Philips HR3287 Service Manual

Philips Domestic Appliances and Personal Care

BOX FAN

HR 3287

PRODUCT INFORMATION

The HR 3287 is a box fan with 3 fan speeds, a timer and a
rotating louvre.

Available voltages : 220 - 240 V / 50-60 Hz

110 - 127 V / 50-60 Hz

Fan blade size : 12 “ or 30 cm

Timer : max 3 hours

Switches for : - ON / OFF louvre rotation

- speed selection fan.

Fan speed selector : 4 positions 0-1-2-3
Air displacement : max. 55 m3/ min
Power consumption : 55 Watts

Safety switch
Red pilot lamp
Adjustable inclination angle 0 - 7.5° - 15°
Internal cord storage

Product meets the requirements regarding interference
suppression on radio and T.V.

Safety switch : The automatic safety switch will switch off the

fan, when it’s lifted or turned over during
operation

Published by P hilips Domestic Appliances and Personal Care Printed in the Netherlands

4822 729 21566
96/01

PCS 86 669

©

Copyright reserved Subject to modification

DISASSEMBLY ADVICE PARTS LIST HR 3287

GRILLE 1

To replace grille:
remove Screw A (2x)
remove Lock plate 2

ORNAMENTAL

PLATE 3

To replace plate:
remove Grille I
remove Screw B (2x)

FAN BLADE 5

To replace fan blade:
remove Grille I
remove Cap fan 4

TIMER KNOB 6

SPEED CONTROL

KNOB 6

KNOB LOUVRE

ROTATION 7

To replace knobs

TIMER 8

ADAPTER TIMER 9

CAPACITOR 12

LOUVRE MOTOR 13

For replacement
remove Timer knob 6
remove Speed control knob 6
remove Knob louvre switch 7
remove Grille 1
remove Screw C (8x)
remove Rear housing 102
remove Screw I Capacitor (lx)
remove Screw J

Louvre motor (2x)

unsolder wiring

SWITCH PLATE 15

SWITCH SPEED

CONTROL 16

remove Timer knob 6
remove Speed control knob 6
remove Knob louvre switch 7
remove Grille 1
remove Screw C (8x)
remove Rear housing 102
remove Screw D (2x)
remove Switch plate 15
remove Screw E (2x)
remove components
unsolder wires

MOTOR 17

remove Timer knob 6
remove Speed control knob 6
remove Knob louvre switch 7
remove Grille 1
remove Fan blade 5
remove Srew C (8x)
remove Rear housing 102
remove Screw F (4x)
remove Motor mount 103
remove Screw G (4x)
remove / unsolder wires

SAFETY SWITCH 19

KNOB SAFETY

SWITCH 18

for replacement
remove Rubber feet 22 (4x)
remove Screw H (4x)
remove Bottom plate 105
remove / unsolder wiring

POS. DESCRIPTION SERVICE CODE

1 GRILLE 4822 458 10479

2 LOCK PLATE 4822 466 10954

3 ORNAMENTAL PLATE 4822 466 10955

4 FAN CAP 4822 462 10693

5 FAN BLADE 4822 515 10053

6 TIMER / SPEED CONTROL 4822 410 10378

7 PUSH BUTTON LOUVRE 4822 410 10379

8 TIMER 220-240 VOLT 4822 282 10283

8 TIMER 110-127 VOLT 4822 282 10284

9 ADAPTER TIMER KNOB 4822 263 21098

10 APAPTER SPEED CONTROL 4822 263 21099

11 SWITCH LOUVRE 110-240 V 4822 276 13706

12 CAPACITOR 220-240 V 4822 121 10522

12 CAPACITOR 110-127 V 4822 121 10523

13 OSCILL. MOTOR 220-240 V 4822 361 10814

13 OSCILL. MOTOR 110-127 V 4822 361 10815

14 PILOT LAMP 220-240 V 4822 134 10026

14 PILOT LAMP 110-127 V 4822 134 10027

15 SWITCH PLATE 4822 466 10956

16 CONTR. SWITCH 110-240 V 4822 273 10306

17 MOTOR 220-240 V 4822 361 10816

17 MOTOR 110-127 V 4822 361 10817

18 SAFETY KNOB 4822 410 10381

19 SAFETY SWITCH 220-240 V 4822 276 13707

19 SAFETY SWITCH 110-127 V 4822 276 13708

20 FIXING NUT LOUVRE 4822 505 11217

21 LOUVRE + BEARING BUSH 4822 458 10481

22 RUBBER FOOT 4822 462 10694

SK3

B

L

N

SK2SK1

A

SK1 = SAFETY SWITCH

= TIMERSK2
= SPEED SELECTOR SWITCHSK3 = LOUVER MOTOR

4
3

2
1

CIRCUIT DIAGRAM

SK4
M1
M2

SLOW
MED

FAST

F
115˚C

M1

C1

R

GL

= SWITCH LOUVER MOTOR
= MOTOR FAN

SK4

M2

ADAPTER SPEED

CONTROL 10

LOUVRE SWITCH 11

CORDSET 101

PILOT LAMP 14

For replacement:
remove Timer knob 6
remove Speed control knob 6
remove Knob louvre switch 7
remove Grille 1
remove Screw C (8x)
remove Rear housing 102
remove / unsolder wires

PCS 86 850

IMPORTANT

* IN SOME CASES THE CONNECTION POINTS BETWEEN WIRING AND ELECTRICAL

COMPONENTS HAVE BEEN INSULATED.
AFTER REPLACEMENT OF A COMPONENT, MAKE SURE THAT THE ELECTRICAL INSULATION
OF THE CONNECTION POINTS HAS BEEN RESTORED BY FITTING THE REGULAR SLEEVE.
IF THIS REGULAR SLEEVE CANNOT BE USED ANYMORE, REPLACE IT WITH A NEW ONE OR
USE INSULATING TAPE, TAKING CARE A PROPER AND SAFE INSULATION IS REALIZED.

* AFTER THE PRODUCT HAS BEEN REPAIRED, IT SHOULD FUNCTION PROPERLY AND HAS TO

MEET THE SAFETY REQUIREMENTS AND LEGAL REGULATIONS AS LAID DOWN AND
OFFICIALLY ESTABLISHED AT THIS MOMENT.

* PARTST, WITH NUMBERS FROM 100 UPWARDS, CANNOT BE ORDERED SEPARATELY.