Philips HR2849 Service Manual

Philips Domestic Appliances and Personal Care

Blender

HR 2849

6000

5000

4000

3000

2000

1000

Product information
HR 2845 = Blender with jar

HR 2849 = HR 2845 with HR 2934

Optional:
HR 2924 = Mill see Service Manual 4822 729 21479
HR 2926 = Chopper see Service Manual 4822 729 21481
HR 2934 = Filter see Service Manual 4322 277 00070

Type no.:
HR 2845/AM means first version and production centre is
Mexico; HR 2845/AB means first version and production
centre is Brazil.

Safety system : The blender operates only if the jar,

mill or chopper is correctly placed
on the drive unit.

Safety cap : The cap locks the lid to the jar in

order to avoid spillage.
Cord storage : It allows control of thecordsetlength.
Switch : 3 speeds with pulse position

in the max position (slide control).
Power consumption : 400 W
Dimensions lxhxw : 18.5 x 38.5 x 17 cm.
Volume jar : Effective 1.5 and total 2.0 litre.
Cleaning : Do not clean the parts in a

dishwasher.

Service Information
Safety device.

The appliance can only be operated if the jar (item 23) is
placed on the body of the appliance so that the safety
interruptor (item 10) located inside the appliance is activated
by means of a shaft (item 9).

Knife assy.

To remove the knife assy (item 17) from the jug (item 23) turn
the knife assy clockwise).

Disassembly of the appliance.

Loosen the two screws to be able to remove the base from
the appliance. Then undo the 3 snap connections which
fasten the base 2 snap connections in the front part and 1
snap connection in the rear part.

Remove the base.

Remove the cover (item 1) of the body (item 3) by undoing its
snap tabs through the 4 openings near the jar coupling.
Drive coupling (item 2) can now be loosened with the help of
a hammer and a screwdriver. Hit the screwdriver with a short
sharp blow of the hammer and remove the drive coupling
clockwise.
Grasp the end of the motor shaft and turn the motor
anticlockwise. Disconnect the motor wires.

Inspection after repair.

Test the safety interruptor by mounting and dismounting the
jar while the appliance is switched on.
Make sure that the speed switch operates properly in all
speed settings.

After the product has been repaired, it should function

Product meets the requirements regarding
interference suppression on radio and TV.

Publishedby Philips DomesticAppliancesandPersonalCare PrintedintheNetherlands

properly and has to meet the safety requirements as
laid down officially established at this moment.

4322 277 00071
02/04

PCS 101 289

©

Copyrightreserved Subject to modification

1 4822 441 31341 Cover drive unit
2 4822 690 40302 Fan coupling
3 4822 441 31364 Top housing
4 Not available
7 4822 532 61264 Motor buffer

8 4822 361 30444 Motor 220 - 230 V

4822 361 30448 Motor 120 - 127 V

9+10 4822 276 13585 Safety system

10 4822 277 21774 Safety switch
12 4822 441 31345 Lower cover

13 4822 441 31347 Bottom housing
14 4822 321 10364 Flex (standard)
15 4822 528 20789 Driven coupling
16 4822 532 52643 Sealing ring
17 4822 690 40299 Knife unit

18 4822 273 10293 Switch and wires
21 4822 441 31335 Cap of jar
22 4822 441 31334 Lid of jar
23 4822 418 40975 Cil. jar

- 4222 000 87410 Direction for use

HR 2934

Filter
4206 136 49450

PCS 101 290