PHILIPS HQ7390 User Manual
ENGLISH 4
FRANÇAIS 15
HQ7390, HQ7380, HQ7363, HQ7360
4
ENGLISH
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at www.philips.
com/welcome.
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- Children should be supervised to ensure that they
do not play with the appliance.
Caution
- Do not use the shaver or the adapter if it is
damaged.
- Only use the adapter supplied.
- If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
- Charge, use and store the shaver at a temperature
between 5°C and 35°C.
- Always unplug the shaver before you clean it
under the tap.
ENGLISH 5
- Be careful with hot water. Always check if the
water is not too hot, to avoid burning your hands.
- The appliance complies with the internationally
approved IEC safety regulations and can be safely
cleaned under the tap.
- This washable shaver is not suitable for shaving in
the shower.
- Do not immerse the shaver in water.
- Water may leak from the socket at the bottom
of the appliance when you rinse it. This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
General
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
Electromagnetic elds (EMF)
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this
user manual, the appliance is safe to use based on
scientic evidence available today.
Charging
Make sure the appliance is switched off before you
start to charge it.
When you charge the shaver for the rst time
or after a long period of disuse, let it charge
continuously for at least 12 hours, for instance
overnight.
ENGLISH6
Charging normally takes 1 hour.
You can also shave without charging by connecting
the shaver to the mains.
Charge indications
Charging
- When you start charging the empty shaver, the
charging light goes on.
Battery fully charged
- When the battery is fully charged, the charging
light starts ashing.
When you unplug the shaver, the charging light goes
out.
Battery running low
- When the battery is running low, the battery-low
light goes on.
When you switch off the shaver, this light ashes a
few times.
Cordless shaving time
After having been charged for 6 minutes, the battery
contains enough energy for one shave.
When the shaver is fully charged, it has a cordless
shaving time of up to 35 minutes.
Charging the appliance
Charge the shaver when the battery-low light goes
on.
1 Put the appliance plug in the shaver.
2 Put the adapter in the wall socket.
3 Remove the adapter from the wall socket and
pull the appliance plug out of the shaver when
the battery is fully charged.
ENGLISH 7
Using the appliance
Shaving
1 Press the on/off button once to switch on the
shaver.
, The power-on lights go on.
2 Move the shaving heads quickly over your skin.
Make both straight and circular movements.
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get accustomed
to the Philips shaving system.
3 Clean the shaver (see chapter ‘Cleaning and
maintenance’).
4 Put the protection cap on the shaver every
time you have used it, to prevent damage to
the shaving heads.
Trimming
You can use the trimmer to groom your sideburns
and moustache.
1 Push the slide downwards to open the
trimmer.
The trimmer can be activated while the motor is
running.
2 Close the trimmer after trimming (‘click’).
ENGLISH8
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
Be careful with hot water. Always check if the
water is not too hot, to avoid burning your hands.
Note: Water may leak from the socket at the bottom of
the appliance when you rinse it. This is normal and not
dangerous.
Every day: shaving unit and hair chamber
1 Switch off the shaver, remove the adapter from
the wall socket and pull the appliance plug out
of the shaver.
2 Press the release button to open the shaving
unit.
3 Rinse the hair chamber and the inside of the
shaving unit under a hot tap for some time.
4 Rinse the outside of the shaving unit.
5 Close the shaving unit and shake off excess
water.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
ENGLISH 9
6 Open the shaving unit again and leave it open
to let the appliance dry completely.
You can also clean the hair chamber without water
by using the brush supplied.
Every six months: shaving heads
1 Press the release button to open the shaving
unit, turn the lock anticlockwise (1) and
remove the retaining frame (2).
2 Clean the cutters and guards with the brush
supplied.
Note: Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it may take
several weeks before optimal shaving performance is
restored.
3 Put the shaving heads back into the shaving
unit. Put the retaining frame back into the
shaving unit and turn the lock clockwise.
4 Close the shaving unit.
Trimmer
Clean the trimmer every time you have used it.
1 Switch off the shaver, remove the adapter from
the wall socket and pull the appliance plug out
of the shaver.
ENGLISH10
2 Clean the trimmer with the brush supplied.
3 Lubricate the trimmer teeth with a drop of
sewing machine oil every six months.
Storage
- Put the protection cap on the shaver to prevent
damage to the shaving heads.
Replacement
Replace the shaving heads every two years for
optimal shaving results.
Replace damaged or worn shaving heads with HQ8
Philips shaving heads only.
Note: Do not mix up the cutters and the guards to
guarantee optimal shaving performance.
1 Switch off the shaver, remove the adapter from
the wall socket and pull the appliance plug out
of the shaver.
2 Press the release button to open the shaving
unit.
Loading...