Philips HQ4800A Service Manual
Rechargeable shaver
Service
Service
Service
Domestic Appliances and Personal Care
R1 |
|
|
|
|
|
|
|
|
|
|
L1 |
|
|
T1 |
|
|
|
|
|
D1 |
|
|
|
|
|
|
|
|
|
|
|
|
D7 |
|
|
|
|
|
|
|
|
|
|
|
|
A |
C6 |
|
|
C1 |
C2 |
R2 |
D2 |
R13 R12 |
|
C5 |
|
||
|
1xAA |
|
M |
||||||
|
|
|
|
||||||
|
|
|
D3 |
|
R11 |
|
NiMH |
SK1 |
D9 |
|
|
|
|
|
D6 |
|
|
|
|
|
|
R3 |
|
|
R8 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TS1 |
R5 |
TS2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TS3 |
|
|
|
|
|
|
D5 |
D4 |
|
|
|
|
|
|
|
|
|
|
|
|
TS5 |
|
|
|
|
|
|
|
|
R10 |
R9 |
|
|
|
|
|
|
R4 |
R7 |
|
|
|
|
|
|
|
|
|
|
|
TS4 |
|
|
|
|
|
|
|
R6 |
R14 |
|
|
|
|
|
|
|
|
C3 |
C4 |
|
|
|
5089 |
|
|
|
|
|
|
|
|
|
GENERAL
The HQ4800 shaver can be recharged in 16 hours by means of a ’Fly Back Self Oscillating Power supply’. This electronic circuit enables the battery to be charged at 100-240V, 50/60Hz.
It is possible to have a shave directly from the mains. The green LED only illuminates when the shaver is connected to the mains.
The electronic circuit incorporates the following functions and controls:
-a 1200 mA Quick Charge supply (Vbat < 1.2V)
-a 15 mA Slow Charge supply (Vbat > 1.2V)
-a 1.25V Dynamic supply when shaving from the mains.
-an open cell protection (C5)
-an inrush and surge protection (R1).
TECHNICAL DATA |
|
|
|
|
Input voltage |
: |
100-240V |
||
Motor voltage |
: |
1.2V |
|
|
|
||||
Battery |
: |
1x AA NiMH |
||
Cell capacity |
: approx. 1100 mAH |
|||
Charging system |
: S.O.P.S./volt. control |
|||
Charging time |
: approx. 16 hours |
|||
|
|
initial 24 hours |
||
Charging current |
: 1200/15 mA |
|||
Charging indicator : |
1x LED green |
|||
Comfort control |
: fixed setting |
|||
Shaving heads |
: HQ4 - 4822 690 30468 |
|||
Screwdriver T8 |
: |
4822 395 50263 |
||
SAP Coding |
: |
HQ4800 |
||
Published by Philips Domestic Appliances and Personal Care Printed in The Netherlands © Copyright reserved Subject to modification
4322 277 00184 00/01
HQ 4800/A
1
2 
3
4
5
Z
A2
1.8x10/T8
+ -
6
7
8
9
10
11
12
13
14
15
15+16
17 X 
18
NiMH
19
20
21 |
A1 |
|
1.8x10/T8 |
||
|
22
Y
23
1 |
4822 441 11276 |
Protecting cap |
16 |
4222 036 02390 |
Motor connector |
2 |
4222 036 01980 |
Head holder |
17 |
4822 277 21689 |
On/off switch |
3 |
4822 690 30468 |
HQ4 shaving head |
18 |
4222 036 02270 |
Power module |
4 |
4822 404 40728 |
Retaining bracket |
19 |
4822 138 10584 |
NiMH cell AA |
5 |
4222 036 02260 |
Housing |
20 |
4222 036 02280 |
Cover |
6 |
4222 036 02370 |
Inlet |
21 |
4822 321 10096 |
Flex GB |
7 |
4222 036 02920 |
Hairchamber |
- |
4822 321 10095 |
Flex EU |
8 |
4822 522 32852 |
Gearwheel |
- |
4222 036 01590 |
Flex RA |
9 |
4822 404 40656 |
Lever |
- |
4822 321 10344 |
Flex USA/CDN |
10 |
4822 441 11275 |
Frame |
22 |
4822 479 30183 |
Cleaning brush |
11 |
4822 522 32851 |
Pinion |
23 |
4822 466 12236 |
Foam plate |
12 |
4822 361 21752 |
Motor |
A |
4822 502 30526 |
S.t. screw 1.8x10/T8 |
134822 492 63165 Motor clamp
144822 690 10081 Trimmer
154822 130 34167 Zener diode
Loading...