Philips HI510 Service Manual

Service Information

Philips Domestic Appliances and Personal Care

PRODUCT INFORMATION

Steam Iron

HI 510 HI 520 HI 530 HI 540

Features HI 510 HI 520 HI 530 HI 540

pilot light x x x x integrated cord winder x x x x spray x x x x variable steam x x x x turbo steam - x x x shot of steam x x x x vertical steam x x x x self-clean x x x x ball swivel - - x x lenght cord set 2.5 m x x x x anti-drip function x x x x automatic shut-off - - - x anodised soleplate x x x x

Voltage / frequency : 100, 120 - 127, 220 - 240 V

50 - 60 Hz

Power consumption : 110 - 110 V, 1200 Watts at 100 V

120 - 127 V, 1450 Watts at 120 V 220 - 240 V, 1600 Watts at 230 V

Sole plate temperature :215±25°C

Steam output : Variable steam output max. 20 gr/min when :

- slide is set to position 6

- temperature dial is set to position MAX.

Turbo steam output :

Always to be used in combination with the variable steam slide, increases the steam output with max 10 gr/min to a total of 30 gr/min.

Shot Of Steam : 60 gr/min

This product meets the requirements regarding interference

suppression on radio and TV.

Turbo steam function :

The steam output of the variable steam function depends upon the position of the slide knob. When set to postition 6 the steam output is 20 gr/min. This might be not sufficient. In that case the turbo button has to be pushed down for max 10 sec. Due to this operation the steam output will increase to 30 gr/min.

Vertical steam :

When the iron is kept in vertical position, the s.o.s button can be used to iron hanging fabrics as curtains.

Self-clean function :

When the self-clean button is pushed down, a sudden flow of water is released from the tank into the heated sole plate. This thermal shock will cause scale particles come loose from the steam chamber. These particles are then flushed out through the steam vents by the water.

Anti-drip :

Water is only released through the tank valve into the steam chamber if the sole plate temperature is high enough to evaporate all water. If the temperature is not hot enough the tank valve is closed by means of the bi-metal disc.

Auto shut-off :

A relay in the electronic module interrupts the power to the heating element when the iron has been motionless in :

- for 30 seconds in horizontal position.

- for 8 minutes in vertical position The red “ Auto off ” pilot light starts blinking. For the 220-240 Volts version only, a sound signal is heard too. When the iron is moved again, it’s automatically switches on again. N.B. When the iron is plugged in in horizontal position, it will not be

switched off during the first 2 minutes to ensure that it heats up properly.

Real-off function

The movement of the thermostat’s bi-metal is limited in downward direction thus will prevent the thermostat contacts from closing at room temperature at MIN setting.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands

4822 729 21818 97/05

PCS 88 672

DISASSEMBLY ADVICE

DIAL 1

RATTLE SPRING 2

CORD SET 3

BACK PLATE 4

SWIVEL 5

remove SCREW C 1x remove BACK PLATE 4

remove SCREWS

cord clamping

INLAY 6

OPERATION KNOBS 7

DOOR 8

DOOR HOLDER/

DEAIR. BUSH 9

SPRAY UNIT 10

PILOT LIGHT 11

PCB 12

remove SCREW C remove BACK PLATE 4 remove INLAY 6

SLIDE UNIT 13

NEEDLE 14

remove SCREW C 1x remove BACK PLATE 4 remove INLAY 6 remove SCREW A 2x

HANDLE 15

SPRAY PUMP 16

S.O.S.PUMP 17

TANK 18

SELF CLEAN

BUTTONS 19

SEALINGS 22

remove SCREW C 1x remove BACK PLATE 4 remove INLAY 6 remove SCREW A 2x remove DIAL 1 remove SCREWS

cord clamping 2x

remove SCREW B 3x remove SCREW A1 2x remove HANDLE 15

THERMOSTAT 20

THERMOSTAT PIN 21

SEALINGS 22

COVER 23

TYPE PLATE 24

SOLE PLATE 25

ANTI-DRIP VALVE 26

remove SCREW C 1x remove BACK PLATE 4 remove INLAY 6 remove SCREW A 2x remove DIAL 1 remove SCREWS

cord clamping cord set pilot light / pcb

remove SCREW B 3x remove SCREW A1 2x remove HANDLE 15 remove SCREW F 3x

Replacement Thermostat see fig.1-4

PCS 88 673

+ 3 hidden pages