Philips HDRW720 Service Manual
Diagnostic Software
Nucleus Name DS_SYS_AudioLoopThroughStop
Nucleus Number 1231
Description Stop routing the audio input to all the outputs
User Input Example DS:> 1231
123100:
Test OK @
Electronic Program Guide Board (EPGB)
Nucleus Name DS_EPGB_VersionGet
Nucleus Number 1300
Description Returns the version of the EPG board.
User Input None
Example DS:> 1300
130000:
Version : 6.1.9
Test OK @
PCMCIA INTERFACE (PCMCIA)
Nucleus Name DS_PCMCIA_Reset
Nucleus Number 1400
Description Reset the PCMCIA device by sending a reset command through IDE
Example DS:> 1400
140000:
Test OK @
EN 75HDRW720/0x 5.
Nucleus Name DS_PCMCIA_Inquiry
Nucleus Number 1401
Description Get the vendor- and product identification and the product revision level of the media
Example DS:> 1401
Nucleus Name DS_PCMCIA_WriteRead
Nucleus Number 1402
Description Perform a Write Read test to a random sector on the inserted medium in the
Example DS:> 1402
Nucleus Name DS_PCMCIA_Diagnostics
Nucleus Number 1403
Description Shall perform the internal diagnostic tests implemented by the media in the slot.
Example DS:> 1403
HARD DISK DRIVE (HDD)
Nucleus Name DS_HDD_Communication
Nucleus Number 2100
Description Check the communication between the digital board and the hard disk drive by
User Input None
Example DS:> 2100
in the slot.
140100:
Test OK @
PCMCIA device and check if the data read is equal to the data written.
140200:
Test OK @
140300:
Test OK @
querying the device type of the hard disk drive
210000:Found a hard disk drive: MASTER device on IDE interface 1
Test OK @
Nucleus Name DS_HDD_Reset
Nucleus Number 2101
Description Reset the hard disk drive
User Input None
EN 76 HDRW720/0x5.
Diagnostic Software
Example DS:> 2101
Nucleus Name DS_HDD_VersionGet
Nucleus Number 2102
Description Get the vendor- and product identification and the product revision level of the hard
User Input None
Example DS:> 2102
Nucleus Name DS_HDD_WriteRead
Nucleus Number 2103
Description Write data to the hard disk, read it back and verify the data read back.
User Input None
Example DS:> 2103
Nucleus Name DS_HDD_CapabilitiesGet
Nucleus Number 2104
Description Get the cylinders, heads and track information of the hard disk drive
User Input None
Example DS:> 2104
210100: Resetting IDE interface 1 succeeded
Test OK @
disk drive
210200: Serial number = F19LP8WE,Firmware rev. = VAM51JJ0 ,Model number =
Maxtor 2F040L0
Test OK @
ATTENTION: THIS NUCLEUS DESTROYS DATA ON THE DISK! A COMPLETE
FORMAT OF THE HDD MIGHT BE NECESSARY!
210300: OK, writing to sector 3f95776
Test OK @
Number of cylinders 16383
Number of heads 16
Number of sectors per track 63
Capacity in sectors 80293248
Number of current cylinders 16383
Number of current heads 16
Number of current sectors per track 63
Current capacity in sectors 16514064
Number of unformatted bytes per track 0
Number of unformatted bytes per sector 0
210400:
Test OK @
Nucleus Name DS_HDD_Diagnostics
Nucleus Number 2105
Description Shall perform the internal diagnostic tests implemented by the hard disk drive.
User Input None
Example DS:> 2105
210500:
Test OK @
Nucleus Name DS_HDD_UploadImage
Nucleus Number 2106
Description Upload raw data from the HDD to a DVD+RW
User Input The user can enter 3 parameters in the next format:
<COMMAND> is one of the next strings:
<HDD sector> = the sector on HDD to start reading from
<HDD sectors> = the number of HDD sectors to transfer
<COMMAND> <HDD sector> <nr of HDD sectors>
· NEW: Create a new transfer image table, <HDD sector> and <nr of HDD
sectors> must be entered. The tray of the DVD drive is sent out an the user
is asked to insert a DVD+RW
· ADD: Add a section to the current transfer table, <HDD sector> and <nr of
HDD sectors> must be entered
· READ: Read the current transfer image table from the DVD. The tray of the
DVD drive is sent out an the user is asked to insert a DVD+RW
· VIEW: View the contents of the current transfer table
· GO: Copy data from the HDD to the DVD+RW according to the currently
entered transfer table
Loading...