Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
ll rights reserved. No part of this publication may by reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronics,
mechanical, photocopying, or otherwise without the prior permission of Philips
TABLE OF CONTENTS
Chapter
Technical Specification and Service hints.…………………1
Safety Instructions………………………………………………2
Instructions for Use……………………………………………. 3
Mechanical Instructions………………………………………. 4
Exploded view and Service parts list…………………...….. 5
Factory Service Mode testing………………………………… 6
Overall Block diagram…………………………………………. 7
Overall Electrical diagram……………………………………. 8
Component layout……………………………………………… 9
Revision list………………………………………………………10
3141 785 30483
Version 1.3
1.0 TECHNICAL SPECIFICATION and SERVICE HINTS
General
Dimensions (WxLx H) : 53 x 86 x 16.7 mm (2.1 x 3.4 x
Weight : 78 g (2.8 oz)
Output power : 2 x 5 mW
Frequency response : 20-20 000 Hz
Equalizer : 5 band DSP controlled
Hard disk : 1,0” micro HDD
Capacity : 3GB
Display : Black/White
Backlight : White Led
Battery : 640 mAh Li-ion internal
Battery life time: >9hr
File transfer rate using
USB :
Battery charging current 320 -420mA
Detection Level Typ.
4-step to 3-step voltage 3.95V
3-step to 2-step voltage 3,8V
2-step to 1-step voltage 3,7V
Force Power Off voltage 3,4V
Current consumption
DC-IN SUPPLY (3.8V)
Battery Charging Current 370mA typ.
BATT. SUPPLY (3.4V)
Power Off <15uA
Idle with LCD Backlight on 55mA
Playback without HDD reading 45mA
Playback with HDD reading 350mA
File transfer using USB1.1 350mA
Service Hints
To replace the Hard disk (HDD) please follow the
below instructions:
ID3-tag support :Yes
PC Connectivity :USB
File Transfer
via Windows Media Player 9 or 10 for music playback
or Windows Explorer for general data (music playback
disabled)
Firmware and software upgrades
For the best interaction between your HDD and your
PC. Check www.philips.com/support for latest
upgrades available.
Firmware upgrade procedure
1. Download the latest version of the Device
Manager application from
http://www.philips.com/support. You may need to
enter your language preference and the model
number e.g.hdd084, to access the Device
Manager application upgrade file.
2. Double click the downloaded execution file to start
the installation of the Device Manager.
3. Once the installation is completed, connect the
GoGear to the power supply with the AC/DC
adapter.
4. Launch the Device Manager at Start->Programs->Philips GoGear HDD->Philips GoGear HDD on
your PC
5. A dialogue box will pop up; click Upgrade to start
the upgrading of the firmware. (Please do not
disconnect the jukebox during the upgrading
process as this interruption may damage the
firmware!)
6. Follow all screen instructions to complete the
firmware upgrade.
7. The Device Manager will close automatically once
the success message is displayed. Close all opened
application and then safely remove your GoGear
1.0 TECHNICAL SPECIFICATION and SERVICE HINTS
micro jukebox by clicking on the icon in your
task tray bar. When prompted, “The USB Mass
Storage Device can now be safely removed from
the system”, click OK and unplug your micro
jukebox.
8. Once the GoGear micro jukebox is disconnected
from the computer, the display will show
“Firmware Upgrading” for a couple of seconds
and then start up as usual. If the message does
not disappear after 2 minutes, do a soft reset by
pressing and holding the key and the volume
+ key for a couple of seconds.
WARNING
GB
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
2.0 SAFTETY INSTRUCTIONS
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
WAARSCHUWING
NL
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
“Pour votre sécurité, ces documents
doivent être utilisés par des spécialistes agréés, seuls habilités à réparer
votre appareil en panne”.
CLASS 1
LASER PRODUCT
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
Varoitus !
SF
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
3122 110 03420
"After servicing and before returning set to customer perform a
leakage current measurement test from all exposed metal parts to
earth ground to assure no shock hazard exist. The leakage current
must not exceed 0.5mA."
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
Overview of controls and connections
3.0 Instructions for use
1USB cable connector
2pHeadphones jack
35V DCCharging socket
4HOLD sliderTo disable key press
5LCD displayDynamically displays menu, options and track information
6VIEWTo switch between root menu, library and now playing screens
73 / 4 Scroll; SuperScroll; 3 / 4
J( / § Rewind / Fast forward; Up / Down to 1 level / Skip to previous / next
y 2;Power on / off and Play / Pause; confirms a menu setting
8Neckstrap eyelet
9Volume + / -Volume control
0RECStart or Stop Voice recording
!PLAYLISTAdd the current track to My Playlist
@MICMicrophone
3
4.0 MECHANICAL INTRUCTIONS
Set Disassembly
1. Remove the Cosmetic screw with an Allen key
2. Use a screwdriver to carefully lift up the back cover of
the device.
3. Gently open up the back cover.
4. Remove 4 x screws. See arrows
4.0 MECHANICAL INTRUCTIONS
5. Open up and remove the bottom part.
6. Remove the battery pack and then the hard disk
7. Take out the 2 screws on the PCB assembly to replace
the board from the casing.
Overview of the disassembly parts
Bottom
parts
Back cover
Mainboard /
LCD
module
Top
assembly /
Key set
Hard
Disk
Battery
PCBA KIT ASSY HDD084/00
PCBA KIT ASSY HDD084/05
PCBA KIT ASSY HDD084/17
PCBA KIT ASSY HDD082/17
PCBA KIT ASSY HDD084/97
HDD 1.0"3GB 000936-02(CORN)Y
HDD 1" 2GB HDD082/17
DAMPER HDD084
KEYSET-FRONT-ASSY HDD084
LENS-PRI ASSY HDD084
SCREW HEXAGON HDD084
MECHANICAL PARTS
MISCELLENEOUS
101 314017750172 COVER-REAR LAQ ASSY HDD084 SIL
102 314017750132 REAR CABINET ASSY HDD084
100 314017750142 FRONT CAB. ASSY HDD084 SILVER
111
314017900111
314017900191
103 314017870131 BATTERY PACK 610MAH LI POLYMER
105
100
314017900181
106 314017900121
107 314017800131
111 314017750181
103
314017040031
112
314017310091 Neck Strap
314017400511 Rubber Sleeve HDD084
314017830122 AY4108/00 AC/DC Adaptor
314017830132 AY4108/05 AC/DC Adaptor
314017830111 AY4108/17 AC/DC Adaptor
908210004736 Headphone SHE775BI/00
102
314011769601 USB CABLE ASSY
101
112
310420052301
108 282206200083
109 314017400331
110 314017750321
105,106
107
110
108
5.0 EXPLODED VIEW & SERVICE PARTS LIST
109
Loading...
+ 17 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.