Philips HB 824-A, HB 821-A Service Manual

Service Service

Service

HPA solarium

HB 821/A HB 824/A

Service Information

Domestic Appliances and Personal Care

Service Information

Service Manual

TECHNICAL DATA

1200W / 230V

Input consumption UV-A source Ballast Starter Timer Hours counter HB 824 Radiation area Protecting goggles Output (minimum) LMV meter HEBRU meter Production code YYWW

3x HPA400 / 118 mm

3x BHA 400L / 230V

3x SN 58-spec.

60 mins motor driven

electro mechanical

185 x 75 cm

HB072 - 4822 690 80147

mW/cm at 65 cm

4.6

2.4

on type plate

SK1

Re1

a1b1

L1 L2 L3

SK2

TIMER

Published by Philips Domestic Appliances and Personal Care Printed in The Netherlands Copyright reserved Subject to modification

S1 S2 S3

SK3

LA1 LA2 LA3

SK4 SK5 TCO

FLOOR PART

HB 824

RADIATION PART

4822 729 21954 98/05

PCS 98 527

IMPORTANT

HINTS FOR REPAIRS

- On account of the short high starting current, the house fuse should be of a 16A-delayed type.

- The appliance will work in operating position only.

- Always check if the protecting glass pane (item 7) is fitted after a repair.

- HPA-lamps only start when they have cooled down sufficiently.

- Never touch a HPA-lamp with your fingers. If necessary, clean the lamp with alcohol.

- Colour differences may occur when new lamps are installed. This phenomenon is characteristic of HPAlamps and disappears after a short period of use.

- After assembly the glass filter should be free from finger prints and dust. Clean the glass filter with alcohol, if necessary.

- Never look in the direction of the radiation part while the lamps are on without wearing protecting goggles.

- In case of insufficient cooling (e.g. when the ventilation apertures are blocked or when the fan is defective) the safety device (item 8) will automatically switch off the solarium. Once the cause of overheating has been removed and the solarium has cooled down sufficiently, the appliance will switch on again automatically.

- When the appliance is a few years old, we advise you to apply a drop of thin oil to the bearings of the fan.

- If the lift mechanism is defective or the wiring between floor part and radiation part is interrupted, you should contact a Philips Service Centre (repair is not possible).

- The above also applies when the housing (item 1) has to be replaced.

- Disassembly of the radiation part:

1. Remove the 10 screws with wich the cover

(item 6) is fastened to the housing (item 1). The cover will continue to cling to the housing.

2. Disconnect the connectors of the connecting cable

and motor.

3. Undo the other connections.

- It can be established whether lamps, ballasts or starters are defective by interchanging them.

- When replacing a lamp holder (item 9) 2 tubular rivets must be drilled out. The bracket is fastened with 2 M2.5x10 bolts.

- Disassembly of the floor part:

1. Remove 6 square and 3 round ornamental props

(item 16).

2. Loosen 14 visible screws by which the cover

(item 15) is fastened.

3. Pass the mains cord cover (item 23A) and the

timer cover (item 13A) through the opening below, after the screws have been taken out.

4. Loosen the screw under the timer cover.

5. Remove the cover (item 15) in horizontal position

so that the screws will not fall out. (As screws with varying length are used, it is not possible to interchange them.)

- Let the solarium cool down first (approx. 15 mins) before closing and storing it away.

- Only move the solarium when folded.

- In case of complaints about little or no tanning, the output can be measured by means of a so-called LMVor HEBRU-meter. The figures given on the tittle sheet are the minimum values to be measured in the centre of the radiation field after 5 mins of warming up and with the appliance connected to the rated voltage.

PCS 66230

- The wheel can be replaced after the decorative cap has been removed by means of a small screwdriver.

PCS 98 528

+ 4 hidden pages