Page 1
Solarium
HB555/A
Philips Domestic Appliances and Personal Care
Service Manual
TECHNICAL INFORMATION
Input consumption : approx. 1160 W / 230 V / 50 Hz
Lamp : 10x TL Cleo Performance 100 W-S
Starter : 10x S12
Ballast : 10x 100 W / 230 V
Timer : 1x 30 mins – motor-driven
Radiation area : 174 x 58 cm
Radiation distance : 20 cm
Height adjustment : between 67 – 97 cm
Protecting goggles : HB071 – 4822 690 80123
Output UVX36 meter : > 4.6 mW/cm² at 20 cm
SK1
M
L
La
S
M1
230 V / 50 Hz
10 x
100 W
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
4322 277 01064
03/02
Page 2
HB555/A
HINTS FOR REPAIRS
- Interchange starters, lamps or ballasts to establish
whether they are defective.
- If they are not defective, check the internal wiring,
especially that connected to the lamp holders.
- The snap-on connections of the wiring can be detached
by means of a paperclip.
- Premature blackening of a tube end points to a defective
starter or a wiring fault.
Replacement of lamps/starters (items 22,10)
Loosen the screws (item 11) and remove the end covers
(items 7, 21).
Pull the acrylic sheet (item 23) out of the appliance.
Now the lamps/starters can be replaced.
Disassembly of gas spring (item 5)
Put the canopy in its highest position.
Fasten ornamental screw (item 4).
Remove the 2 screws (A).
Lift the canopy off the foot together with a second person.
Place the canopy on a soft surface.
The gas spring can now be taken out.
Disassembly of fan (item 16)
Unlock the clamps of the fan cover (item 15).
Loosen the connecting wires and pull out the fan unit
(item 16).
Disassembly of timer (item 18)
Remove the end cover on the side where the timer is
located.
Pull the top cover on this side out of the groove of the side
panel (item 19).
Pull the side panel off the metal frame to create enough
room to remove the timer.
Disassembly of hinge (items 12, 13 and 14)
Unlock the clamps of the hinge cover with a screwdriver.
Loosen the screw (B).
Ask a second person to depress the locks of the bearing
bush (item 14) with two small screwdrivers.
Position yourself on the other side of the appliance and
press the stand with your foot while pulling the canopy
slightly (approx. 5 mm) towards you to deactivate the lock.
Now you and the other person should position yourselves
at opposite ends of the appliance. Lift the canopy from the
stand by pulling at it.
Place the canopy on a soft surface.
Remove the lock spring (item 13)
Tap the bearing bush off the shaft with a plastic hammer.
2-4
Page 3
HB555/A
Pos Service code Description
1 4822 690 80123 HB 071 protecting goggles
2 4822 321 11395 mains fl ex
3 9965 000 11518 panel rear
4 9965 000 11530 orn. screw
5 9965 000 11527 gas spring
6 4822 146 10344 ballast 100 W
7 9965 000 11523 end cover
8 9965 000 01934 lamp holder
9 9965 000 01933 lamp/starter holder
10 4822 219 80258 starter S12
11 4822 502 14539 s.t. screw 4.8 x 19
12 9965 000 11528 hinge cap
13 9965 000 11525 securing spring
14 9965 000 11526 bearing bush
15 9965 000 11521 fan cover
Pos Service code Description
16 9965 000 11520 fan complete
17 9965 000 11524 top cover
18 9965 000 11519 timer 30 mins
19 9965 000 11517 panel front
20 4822 410 11079 timer knob
21 see item 7
22 9280 043 21920 TL Cleo Performance 100 W-S
23 9965 000 11522 acrylic sheet
24 9965 000 11531 U-shaped foot
25 9965 000 11529 swivel wheel
9965 000 11532 mounting set
= changed
S2
S4
S6
S8
S10
SK1
M
La1 - 100 W
La2 - 100 W
La3 - 100 W
La4 - 100 W
La5 - 100 W
La6 - 100 W
La7 - 100 W
La8 - 100 W
La9 - 100 W
La10 - 100 W
L1L6
S1
S3
S5
S7
S9
230 V / 50 Hz
M1
L4L5L10L9
L
N
NNL1L
1
L2L3L8L7
3-4
Page 4
HB555/A
15
1
16
2
17
18
19
20
3
B
4
12
13
14
21
10
11
5
6
7
22
23
8
9
A
24
25
4-4
Loading...