Philips GC9080 Service Manual

Active Ironing Board

GC9080

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

Features

- Double-sided ironing

- Heater temperature : 60 ± 5 °C

- Iron stand tray click-on system

- Large ironing surface : 1.10 m x 0.42 m

- Adjustable heights : 0.74 - 0.94 m

- Single leg construction

- Power cord length : 3m

- Cord storage compartment

- Wheels feature

Safety Information

- This product meets the requirements regarding
interference suppression on radio and TV.

- After the product has been repaired, it should function
properly and has to meet the safety requirements and
legal regulations as officially laid down at this moment.

TECHNICAL INFORMATION

- Voltage : 220 - 240 V

- Frequency : 50 - 60 Hz

- Power Consumption : 320 W - 380 W

- Dimension (F-box) : 160 cm (L) x 54 cm (W) x (27 cm (H)

- Weight (Product) : 17 kg

Double-sided Ironing

The surface is heated, allowing double-sided ironing, giving
you faster and better result.
There are also on-board suction fan and blowing fan.
The suction fan can affi x garments to the board for easier
ironing. The blowing fan creates an air cushion on which
delicate garment can be ironed without false creases.

Iron stand tray click-on system

The Philips Intellicare and the Provapor have a perfect fi t
on this new and strong support as a result of its shape and
click-on system. This can accommodate both left and right
handed.

Adjustable heights

The height of the ironing board can be set from 74 cm to
94 cm (6 positions) to suit different people.

Single leg construction

The single leg construction allows you to sit comfortably
while ironing. The pivot joint of the legs is in the middle,
making it well-suited for sitting on either side of the board.

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

04/03

DISASSEMBLY ADVICE

GC9080

IRONING BOARD

TOP COVER 1

IRONING BOARD TOP 2

HEATING ELEMENT ASSY 4

FELT WITH ADHESIVE 5

THERMOSTAT 6

Remove IRONING BOARD
COVER 1

Remove IRONING BOARD
CLIP 3 (8x)

Open Heating element clip (6x)

IRON TRAY ASSY 7

FAN BLADE 11

FAN MOTOR (SUCTION) 12

FAN MOTOR (BLOWING) 13

CONTROL PANEL ASSY 14

MAIN SWITCH 15

FAN SELECTOR SWITCH 16

POWER SOCKET 17

CORDSET ASSY 18

Turn the Ironing Board
Remove Screw cover at tray (2x)
Remove Bolt A (2x)
Remove Leg from Ironing Board
Remove Screws B (Torx T20) (2x)
Remove IRON TRAY ASSY 7
Remove Screws C (‘+’) (6x)
Remove Screws D (Torx T20) (5x)
Remove Fan Housing
Remove Cord Storage Compartment
Remove CONTROL PANEL

ASSY 14

HINGE LEG ASSY 21

Remove SCREW COVER (grey) 20
(2x)

Remove Bolt E

WHEEL ASSY 22

Remove SCREW COVER (grey) 20
(2x)

Remove Bolt F

REPAIR INSTRUCTIONS

- You will need a Torx T20 screwdriver.

- IRONING BOARD CLIP 3 must be replaced with new one once it is disassembled.

- FAN CLIP 10 needs to be removed before disassembling FAN BLADE 11.

- Fan motor wiring : Black connector => Suction fan
White connector => Blowing fan

2-4