Philips GC8930/10 user manual [tr]
GC8900 series
© 2022 Philips Domestic Appliances Holding B.V.
All rights reserved
4239 001 1354 2 (25/01/2022)
User Manual
Қолданушының нұсқасы
Инструкция по эксплуатации
Kullanım Kılavuzu
1
2
1
2
3
5 6 7
910
11
8
1 2
4
13
15
1214
1
Türkçe
Sorun Neden Çözüm
EASY DECALC düğmesinin lastik
contası aşınmıştır.
Ütü ısınmıyor ve sarı
DECALC ışığı yanıp
sönüyor.
Cihaz size kireç temizleme
adımlarını gerçekleştirmeniz
gerektiğini hatırlatıyordur. Işık
yaklaşık bir aylık kullanımdan
sonra yanar.
Yeni bir EASY DECALC düğmesi almak
için yetkili bir Philips servis merkezi ile
iletişime geçin.
“Cihazın kirecini temizleme”
bölümünde yer alan talimatları
uygulayarak kireç temizleme adımlarını
gerçekleştirin.
25
2
6
3
7
4
8
5
9
Garanti ve destek
Bilgi veya desteğe ihtiyaç duyarsanız lütfen www.philips.com/support adresini ziyaret edin veya
uluslararası garanti kitapçığını okuyun.
10
11
12
13
14
18
15
19
16
2 hr
20
17
21
22
23
24
25
English 6
Қазақша 11
Русский 16
Türkçe 21
English
6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet from the support that Philips
oers, register your product at www.philips.com/welcome.
Read this user manual, the important information leaet, and the quick start guide carefully before you use
the appliance. Save them for future reference.
Product overview (Fig. 1)
1 Steam supply hose
2 Steam trigger/Steam boost
3 ‘Iron ready’ light
4 Soleplate
5 Iron platform
6 Carry lock release button
7 Detachable water tank
8 Filling hole
9 Supply hose storage compartment
10 EASY DECALC knob
11 Mains cord with plug
12 EASY DECALC light
13 ECO button with light
14 ‘Water tank empty’ light
15 On/o button with power-on light and auto-o light
Preparing for use
Type of water to use
This appliance has been designed to be used with tap water. However, if you live in an area with hard
water, fast scale build-up may occur. Therefore, it is recommended to use distilled or demineralized water
(50% demineralized/distilled water mixed with water could be used as well) to prolong the lifetime of the
appliance.
Warning: Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling
agents, ironing aids, chemically descaled water or other chemicals, as they may cause water spitting,
brown staining or damage to your appliance.
Filling the water tank
Fill the water tank before every use or when the ‘water tank empty’ light ashes. You can rell the water
tank at any time during use.
1 Remove the water tank from the appliance (Fig. 2) and ll it with water up to the MAX indication (Fig. 3).
2 Put the water tank back into the appliance by tting the bottom part into the appliance rst.
3 Push in the top part of the water tank until it locks into place (‘click’) (Fig. 4).
Water tank empty light
When the water tank is almost empty, the ‘water tank empty’ light ashes (Fig. 5). Fill the water tank
and press the steam trigger to let the appliance heat up again. When the ‘iron ready’ light lights up
continuously, you can continue steam ironing.
English
Using the appliance
OptimalTEMP technology
Warning: Do not iron non-ironable fabrics.
The OptimalTEMP technology enables you to iron all types of ironable fabrics, in any order, without
adjusting the iron temperature and without sorting your garments.
It is safe to just rest the hot soleplate directly on the ironing board (Fig. 6) without putting back to the iron
platform. This will help reduce the stress on your wrist.
- Fabrics with these symbols (Fig. 7) are ironable, for example linen, cotton, polyester, silk, wool, viscose
and rayon.
- Fabrics with this symbol (Fig. 8) are not ironable. These fabrics include synthetic fabrics such as Spandex
or elastane, Spandex-mixed fabrics and polyolens (e.g. polypropylene). Prints on garments are not
ironable either.
Ironing
1 Place the steam generator on a stable and even surface.
Note: In order to ensure safe ironing we recommend to always place the base on a stable ironing board.
2 Make sure that there is enough water in the water tank (see ‘Filling the water tank’).
3 Put the mains plug in an earthed wall socket and press the on/o button to switch on the steam
generator. Wait until the ‘iron ready’ light lights up continuously (Fig. 9). This takes approx. 2minutes.
4 Remove the steam supply hose from the steam supply compartment.
5 Press the carry lock release button to unlock the iron from the iron platform (Fig. 10).
6 Press and hold the steam trigger to start ironing (Fig. 11).
Note: For rst use, press and hold the steam trigger continuously for up to 30 seconds for steam. It can
take a longer time if the iron is stored for a long time.
7 For best ironing results, after ironing with steam, perform the last strokes without steam.
7
MAX setting
For faster ironing and a higher amount of steam, you can use MAX setting.
1 Press and hold the on/o button for 5 seconds until the light turns white.
2 The appliance returns to normal steam mode automatically after 15 minutes to save energy.
3 Otherwise, to switch back to normal steam mode at any time, press and hold the on/o button for
2seconds until the light turns blue again.
Steam boost function
The steam boost function is designed to help tackle dicult creases.
- Press the steam trigger twice quickly to activate the steam boost function. The appliance releases
3powerful shots of steam.
- To stop the steam boost function, press the steam trigger once.
Vertical ironing
Warning: Hot steam is emitted from the iron. Never attempt to remove wrinkles from a garment
while someone is wearing it (Fig. 12). Do not apply steam near your or someone else's hand.
You can use the steam iron in vertical position to remove wrinkles from hanging fabrics.
1 Hold the iron in vertical position, press the steam trigger and touch the garment lightly with the soleplate
and move the iron up and down (Fig. 13).
English
8
Safe rest
Resting the iron while rearranging your garment
While rearranging your garment, you can rest the iron either on the iron platform or horizontally on the
ironing board (Fig. 6). The OptimalTEMP technology ensures the soleplate will not damage the ironing
board cover.
Energy saving
ECO mode
By using the ECO mode (reduced amount of steam), you can save energy without compromising on the
ironing result.
1 To activate the ECO mode, press the ECO button (Fig. 14). The green ECO light goes on.
2 To deactivate the ECO mode, press the ECO button again. The green ECO light goes out.
Auto-shut o
- To save energy, the appliance switches o automatically when it has not been used for 10 minutes. The
auto-o light in the on/o button starts to ash.
- To activate the appliance again, press the on/o button. The appliance then starts to heat up again.
Warning: Never leave the appliance unattended when it is connected to the mains. Always unplug
the appliance after use.
Cleaning and maintenance
Descaling the appliance
It is very important to use the EASY DECALC function as soon as the ‘EASY DECALC’ light starts to ash
(Fig.15).
The ‘EASY DECALC’ light ashes after about a month or 10 ironing sessions to indicate that the appliance
needs to be descaled. Perform the following EASY DECALC procedure before you continue ironing.
Note: If your water is hard, increase the descaling frequency.
Warning: To avoid the risk of burns, unplug the appliance and let it cool down for at least two
hours before you perform the EASY DECALC procedure (Fig. 16).
1 Remove the plug from the wall socket.
2 Remove the detachable water tank (Fig. 2).
3 Remove the iron from the iron platform.
4 Hold and shake the base of the steam generator (Fig. 17).
5 Remove the EASY DECALC knob (Fig. 18).
6 Hold the base of the steam generator over the sink and empty it through the EASY DECALC opening
(Fig.19).
Note: Be mindful on the heavy weight of the appliance when you tilt it.
7 Reinsert the EASY DECALC knob and turn it clockwise to fasten it (Fig. 20).
8 You can continue using your iron immediately after completing the EASY DECALC procedure.
Descaling the soleplate
If you do not descale your appliance regularly, you may see brown stains coming out of the soleplate due
to scale particles. Descale the soleplate by following the procedure below. We advise you to perform the
procedure twice for better results.
1 Make sure the appliance is cool and clean the soleplate with a damp cloth.
2 Remove the water tank and iron from the iron platform.
3 Remove the EASY DECALC knob and empty the water through the EASY DECALC opening.
English
4 Hold the appliance in the position that the EASY DECALC opening is facing up and pour 500ml water
into the opening (Fig. 21).
Note: Be mindful on the heavy weight of the appliance when you tilt it.
5 Keep the EASY DECALC opening facing up, reinsert the EASY DECALC knob and turn it clockwise to
fasten it (Fig. 22).
6 Put the appliance back on a stable and even surface. Fill up the water tank halfway. Switch on the
appliance and wait for 5 minutes.
7 Keep the steam trigger pressed continuously while you iron a few pieces of thick cloth in a back-and-
forth motion for 3 minutes (Fig. 23).
Warning: Hot, dirty water (about 100-150 ml) comes out of the soleplate.
8 Stop cleaning when no more water comes out of the soleplate or when steam starts coming out of the
soleplate.
9 You can continue to use the appliance immediately. Otherwise unplug the appliance after the descaling
is completed.
Storage
1 Switch o the appliance and unplug it.
Note: it is recommended to empty the water tank after every use.
2 Place the iron on the iron platform and lock it by pushing the carry lock release button (Fig. 24).
3 Let the appliance cool down completely.
4 Fold the supply hose and wind the supply hose inside the supply hose storage compartment (Fig.25).
5 Fold the mains cord and fasten it with the Velcro strip.
6 You can carry the appliance with one hand by the handle of the iron when the iron is locked on the iron
platform.
Troubleshooting
This chapter summarizes the most common problems you could encounter with the appliance. If you are
unable to solve the problem with the information below, visit www.philips.com/support for a list of
frequently asked questions or contact the Consumer Care Center in your country.
Problem Cause Solution
Dirty water, brown stains
or white akes come out of
the soleplate.
There is no or little steam. The appliance has not heated up
Water leaks from the
soleplate.
Scale has built up inside the
appliance because it has not been
descaled regularly.
You have put chemicals or
additives in the water tank.
suciently.
There is not enough water in the
water tank.
Scale has built up inside the
appliance because it has not been
descaled regularly.
Steam condenses into water in
the hose when you use steam for
the rst time or have not used it
for a long time.
Descale the appliance and the
soleplate (see chapter 'Cleaning and
maintenance').
Never use chemical or additives with
the appliance. If you have already done
so, follow the procedure in chapter
'Cleaning and maintenance' to remove
the chemicals.
Wait until the iron ready light stays
on continuously. This takes approx. 2
minutes.
Fill the water tank up to the MAX
indication.
Descale the appliance and soleplate (see
chapter ‘Cleaning and maintenance’).
This is normal. Hold the iron away
from the garment and press the steam
trigger. Wait until steam instead of
water comes out of the soleplate.
9
Loading...