Philips GC2025/02, GC2020/02, GC2015/02, GC2010/02, GC2006/02 User Manual [es]

...
Mistral
GC2030,GC2025,GC2020,GC,2016, GC2015,
GC2011,GC2010,GC2006,GC2005
ENGLISH 4 ESPAÑOL 12 PORTUGUÊS 20
TÜRKÇE 28
3
Important
For optimal safety,read these instructions carefully and look at the illustrations before you start using the appliance.
- Never leave the iron unattended when it is connected to the mains.
- Young children should not be allowed to use the appliance without supervision. Keep an eye on children to make sure that they do not play with the appliance.
- The soleplate of the iron can become extremely hot and may cause burns if touched. Do not allow the cord to come into contact with the soleplate when it is hot.
- When you have finished ironing, when you clean the appliance, when you fill or empty the water tank and also when you leave the iron even for a short while: set the steam control to position O,put the iron on its heel and remove the mains plug from the wall socket.
- If the mains cord of this appliance is damaged,it must always be replaced by Philips or a service centre authorised by Philips,as special tools and/or parts are required.
- Never use the appliance if it is damaged in any way.
Before first use
1 Check if the voltage indicated on the type plate corresponds to
the mains voltage in your home before you connect the appliance.
2 Remove any sticker,protective foil or storage cover from the
soleplate.
3 Heat up the iron to maximum temperature and pass the iron
over a piece of damp cloth for several minutes to remove any residues from the soleplate.
The iron may give off some smoke when you use it for the first time. This will cease after a short while.
Filling the water tank
Never immerse the iron in water.
1 Remove the mains plug from the wall socket.
C
2 Set the steam control to position O (= no steam). 3 Tilt the iron.
ENGLISH4
C
4 Pour tap water into the water tank by means of the filling jug
and fill the tank to maximum level.
Do not fill the water tank beyond the MAX indication. If the tap water in your area is very hard, we advise you to use distilled
water. Do not use vinegar, starch or chemically descaled water.
Setting the temperature
1 Put the iron on its heel.
C
2 Set the temperature dial to the required ironing temperature
by turning it to the position of the temperature indicator.
- Check the garment label for the required ironing temperature.
- 1 Synthetic fabrics (e.g. acrylic, viscose,polyamide,polyester)
- 1 Silk
- 2 Wool
- 3 Cotton, linen
- If you do not know what kind of fabric(s) a garment is made of, determine the right ironing temperature by ironing a part that will be invisible when you wear the garment.
- Silk,woollen and synthetic materials:iron the reverse side of the fabric to prevent shiny patches.To prevent stains, avoid using the spray function.
- Start ironing the articles that require the lowest ironing temperature, such as those made of synthetic fibres.
3 Put the mains plug in an earthed wall socket. 4 When the amber temperature pilot light has gone out,wait a
while before you start ironing.
B
The amber pilot light will come on from time to time during ironing.
For auto-shut-off versions (only type GC2030): If the auto-shut-off function has been activated (red pilot light blinks),
move the iron slightly to deactivate it (red pilot light stops blinking).
Steam ironing
Make sure that there is enough water in the water tank.
1 Set the temperature dial to the recommended position.
See 'Setting the temperature'.
ENGLISH 5
N
Y
L
O
N
N
Y
L
O
N
S
S
I
O
L
K
I
E
L
A
W
I
N
O
E
O
L
N
N
I
E
L
N
I
L
N
O
T
O
N
C
O
T
T
O
C
C
2 Set the steam control to the appropriate steam position.
- q for moderate steam (temperature settings 2 to 3)
- w for maximum steam (temperature settings 3 to MAX)
B
Steaming will start as soon as the set temperature has been reached.
Types GC2005,2006,2010, 2011,2015,2016:Water may leak from
the soleplate if the set temperature is too low (MIN to 2).
Ironing without steam
1 Set the steam control to position O ( = no steam). 2 Set the temperature dial to the recommended position.
See 'Setting the temperature'.
Other features
Spraying
To remove stubborn creases at any temperature Make sure that there is enough water in the water tank.
C
1 Press the spray button a couple of times to moisten the
laundry.
Extra Steam (types GC2020,2006,2005 only)
This function provides extra stream to remove stubborn creases. The Extra Steam function only works at temperature settings between 3 and MAX.
C
1 Set the steam control to highest position q.
C
2 Press and hold the Extra Steam button down for max.5
seconds.
3 Wait for at least 1 minute before you use the Extra Steam
function again to prevent water from dripping out of the soleplate.
ENGLISH6
Shot of Steam (types GC2030,2025,2016,2015,2011,2010 only)
A powerful shot of steam helps to remove stubborn creases. The Shot-of-Steam function only works at temperature settings between 2 and MAX.
C
1 Press and release the Shot-of-Steam button.
Vertical Shot of Steam (types GC2030,2025,2016,2015 only)
C
1 The Shot of Steam function can also be used when you hold
the iron in vertical position.
Never direct the steam towards people.
Drip Stop (types GC2030,2025,2020 only)
This iron is equipped with a drip stop function: the iron automatically stops steaming when the temperature is too low to prevent water from dripping out of the soleplate.When this happens you will hear a click.
Automatic shut-off (type GC2030 only)
C
An electronic safety device will automatically switch the heating
element off if the iron has not been moved for a while.
To indicate that the heating element has been switched off,the red
auto-off pilot light will start blinking.
To heat up the iron again:
1 Pick up the iron or move it slightly. 2 The red auto-off pilot light will go out.The amber temperature
pilot light will come on,depending on the soleplate temperature.
ENGLISH 7
3 If the amber pilot light comes on after the iron has been
moved,wait for it to go out before you start ironing.
4 If the amber light does not come on after the iron has been
moved,the iron is ready for use.
Cleaning and maintenance
Calc-Clean
The Calc-Clean function removes scale and impurities. Use the Calc-Clean function once every two weeks. If the water in your area is very hard (i.e. when flakes come out of the soleplate during ironing), the Calc-Clean function should be used more frequently.
1 Set the steam control to position O. 2 Fill the water tank to the maximum level.
Do not pour vinegar or other descaling agents into the water tank..
3 Set the temperature dial to MAX. 4 Put the plug in the wall socket. 5 Unplug the iron when the amber pilot light has gone out.
C
6 Hold the iron over the sink and set the steam control to
position v (Calc-Clean).The steam control knob will spring up slightly.
C
7 Pull the steam control up slightly and gently shake the iron.
B
Steam and boiling water will come out of the soleplate.Impurities and scale (if any) will be flushed out.
C
8 Pull the steam control knob further up to remove the steam
control needle.Use vinegar to remove scale, if any, from the needle.
Do not bend or damage the steam control needle.
ENGLISH8
C
9 Put the steam control needle back by inserting the point of the
needle exactly in the centre of the hole and by fitting the small projection on the side of the needle into the slot.Set the steam control knob to position O.
Repeat the Calc-Clean process if the iron still contains a lot of impurities.
After the Calc-Clean process
- Plug in the iron to let the soleplate dry up.
- Unplug the iron when the amber pilot light has gone out.
- Move the iron gently over a piece of used cloth to remove any water stains that may have formed on the soleplate.
- Let the iron cool down before you store it.
After ironing
1 Remove the mains plug from the wall socket and let the iron
cool down.
2 Wipe scale and any other deposits off the soleplate with a
damp cloth and a non-abrasive (liquid) cleaner.
Keep the soleplate smooth:avoid hard contact with metal objects.
3 Clean the upper part of the appliance with a damp cloth.
C
4 Regularly rinse the water tank with water.Empty the water
tank after cleaning.
Storage
1 Remove the mains plug from the wall socket and set the steam
control to position O.
2 Empty the water tank.
C
3 Let the iron cool down.Wind the mains cord round the cord
storage facility and fix it with the cord clip.
4 Always store the iron standing on its heel in a safe and dry
place.
ENGLISH 9
Information & service
If you need information or if you have a problem, please visit the Philips Web site at www.philips.com or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country,turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.
ENGLISH10
Solution
Check the mains cord,the plug and the wall socket.
Set the temperature dial to the required temperature.
Fill the water tank (see Filling the water tank).
Set to steam position q or w (see Steam ironing).
Set the temperature dial to a temperature in the steam area (&@4,050 to MAX).Put the iron on its heel and wait until the amber pilot light has gone out before you start ironing.
Put the iron in horizontal position and wait for a while before using the (Vertical) Shot of Steam function again.
Set the temperature dial to a temperature in the steam area (&@4,050 to MAX).Put the iron on its heel and wait until the amber pilot light has gone out before you start ironing.
Use the Calc-Clean function a few times (see 'Calc-Clean').
Shake the iron lightly to deactivate the auto shut-off function:the pilot light will stop blinking.
Set the temperature dial to a temperature in the steam area (&@4,050 to MAX).Put the iron on its heel and wait until the amber pilot light has gone out before you start ironing.
Possible cause(s)
Connection problem.
Temperature dial set at MIN.
Not enough water in the water tank.
The steam control has been set to position O.
The soleplate is not hot enough and/or the Drip Stop function (types GC2030,2025,2020) has been activated.
The (Vertical) Shot of Steam function has been used too often within a very short period.
The soleplate is not hot enough.
Hard water forms flakes inside the soleplate.
The auto shut-off function has been activated.See "Automatic shut-off" section.
The temperature has been set too low.
Problem
The iron is plugged in but the soleplate is cold.
No steam
No Shot of Steam (type GC2010, 2011,2015,2016, 2025,2030 only) or no Vertical Shot of Steam (Types GC2030,2025,2016,2015 only)
Flakes and impurities come out of the soleplate during ironing.
Red pilot light is blinking (type GC2030 only).
Water drips out of the soleplate (types GC2016,2015,2011, 2010,2006,2005 only).
ENGLISH 11
Troubleshooting
This chapter summarises the most common problems you could encounter with your iron.Please read the different sections for more details.If you are unable to solve the problem, please contact the Philips Customer Care Centre in your country.See the worldwide guarantee leaflet for telephone numbers of the or visit our website at www.philipsonline.com.
Loading...
+ 24 hidden pages