All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto
is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way
without the express written consent of Funai. All other trademarks used herein remain the exclusive property of
their respective owners. Nothing contained in this manual should be construed as granting, by implication or
otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any
other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights
to the fullest extent of the law.
A91F2UH/FAUH/FJUH/FKUH/FQUF/FRUF
091014
Page 2
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all
P&F Equipment. The service procedures recommended by P&F and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
P&F could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, P&F has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by P&F must first use
all precautions thoroughly so that neither his safety nor the safe operation
of the equipment will be jeopardized by the service method selected.
The LCD panel is manufactured to provide many years of useful life.
Occasionally a few non active pixels may appear as a tiny spec of color.
This is not to be considered a defect in the LCD screen.
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV
Circuit
1. Before returning an instrument to the
customer, always make a safety check of the
entire instrument, including, but not limited to, the
following items:
a. Be sure that no built-in protective devices are
defective and have been defeated during
servicing. (1) Protective shields are provided
on this chassis to protect both the technician
and the customer. Correctly replace all missing
protective shields, including any removed for
servicing convenience. (2) When reinstalling
the chassis and/or other assembly in the
cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating
fishpapers, adjustment and compartment
covers/shields, and isolation resistor/capacitor
networks. Do not operate this instrument or
permit it to be operated without all
protective devices correctly installed and
functioning. Servicers who defeat safety
features or fail to perform safety checks
may be liable for any resulting damage.
b. Be sure that there are no cabinet openings
through which an adult or child might be able to
insert their fingers and contact a hazardous
voltage. Such openings include, but are not
limited to, (1) spacing between the Liquid
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly
secured cabinet back cover.
c. Antenna Cold Check - With the instrument AC
plug removed from any AC source, connect an
electrical jumper across the two AC plug
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch
the other ohmmeter lead in turn to each tuner
antenna input exposed terminal screw and, if
applicable, to the coaxial connector. If the
measured resistance is less than 1.0 megohm
or greater than 5.2 megohm, an abnormality
exists that must be corrected before the
instrument is returned to the customer. Repeat
this test with the instrument AC switch in the off
position.
d. Leakage Current Hot Check - With the
instrument completely reassembled, plug the
AC line cord directly into a 120 V AC outlet. (Do
not use an isolation transformer during this
test.) Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI) C101.1
Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on
position and then in the off position, measure
from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal
cabinet, screw heads, metallic overlays, control
shafts, etc.), especially any exposed metal
parts that offer an electrical return path to the
chassis. Any current measured must not
exceed 0.5 milli-ampere. Reverse the
instrument power cord plug in the outlet and
repeat the test.
READING SHOULD
NOT BE ABOVE 0.5 mA
LEAKAGE
DEVICE
BEING
TESTED
TEST ALL EXPOSED
METAL SURFACES
ALSO TEST WITH
PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
ANY MEASUREMENTS NOT WITHIN THE
LIMITS SPECIFIED HEREIN INDICATE A
POTENTIAL SHOCK HAZARD THAT MUST
BE ELIMINATED BEFORE RETURNING THE
INSTRUMENT TO THE CUSTOMER OR
BEFORE CONNECTING THE ANTENNA OR
ACCESSORIES.
2. Read and comply with all caution and safety-
related notes on or inside the receiver cabinet, on
the receiver chassis, or on the Liquid Crystal
Panel.
CURRENT
TESTER
+
EARTH
GROUND
_
2-1LTVN_ISP
Page 6
3. Design Alteration Warning - Do not alter or add
to the mechanical or electrical design of this TV
receiver. Design alterations and additions,
including, but not limited to circuit modifications
and the addition of items such as auxiliary audio
and/or video output connections, might alter the
safety characteristics of this receiver and create a
hazard to the user. Any design alterations or
additions will void the manufacturer's warranty and
may make you, the servicer, responsible for
personal injury or property damage resulting
therefrom.
4. Hot Chassis Warning a. Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord and maybe safety-serviced without
an isolation transformer only if the AC power
plug is inserted so that the chassis is
connected to the ground side of the AC power
source. To confirm that the AC power plug is
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0 V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
7. Product Safety Notice - Some electrical and
mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by a # on schematics and in parts lists.
Use of a substitute replacement that does not
have the same safety characteristics as the
recommended replacement part might create
shock, fire, and/or other hazards. The product's
safety is under review continuously and new
instructions are issued whenever appropriate.
Prior to shipment from the factory, our products
are strictly inspected to confirm they comply with
the recognized product safety and electrical codes
of the countries in which they are to be sold.
However, in order to maintain such compliance, it
is equally important to implement the following
precautions when a set is being serviced.
2-2LTVN_ISP
Page 7
Precautions during Servicing
A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
B. In addition to safety, other parts and assemblies
are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F.Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I.Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal
connectors, first, disconnect the AC plug from the
AC supply outlet.
L. When installing parts or assembling the cabinet
parts, be sure to use the proper screws and
tighten certainly.
2-3LTVN_ISP
Page 8
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Chassis or Secondary Conductor
Primary Circuit
AC Line VoltageRegion
110 to 130 V
Note: This table is unofficial and for reference only. Be
sure to confirm the precise values.
U.S.A. or
Canada
Clearance
Distance (d), (d’)
≥ 3.2 mm
(0.126 inches)
2. Leakage Current Test
Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
d'd
Fig. 1
Exposed Accessible Part
Z
AC Voltmeter
(High Impedance)
Earth Ground
B
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas
AC Line VoltageRegionLoad ZLeakage Current (i)Earth Ground (B) to:
110 to 130 V
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
U.S.A. or
Canada
0.15 µF CAP. & 1.5 kΩ
RES. Connected in parallel
2-4LTVN_ISP
i ≤ 0.5 mA rms
Exposed accessible
parts
Page 9
STANDARD NOTES FOR SERVICING
Circuit Board Indications
1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
Top View
Out
2. For other ICs, pin 1 and every fifth pin are
indicated as shown.
Pin 1
3. The 1st pin of every male connector is indicated as
shown.
Pin 1
Input
In
Bottom View
5
10
Pb (Lead) Free Solder
Pb free mark will be found on PCBs which use Pb
free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs
without Pb free mark, use standard solder.
Pb free mark
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering
machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
Fig. S-1-1
2. Remove the flat pack-IC with tweezers while
applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
3-1TVN_SN
Page 10
3. The flat pack-IC on the CBA is affixed with glue, so
be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
CBA
Masking
Tape
Tweezers
Hot-air
Flat Pack-IC
Desoldering
Machine
Flat Pack-IC
Fig. S-1-2
Flat Pack-IC
Desoldering Braid
Soldering Iron
Fig. S-1-3
2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Sharp
Pin
Fine Tip
Soldering Iron
3. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Fig. S-1-4
3-2TVN_SN
Page 11
With Iron Wire:
1. Using desoldering braid, remove the solder from
all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting
point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering
iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the
CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using
tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Hot Air Blower
2. Installation
1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. The “●” mark on the flat pack-IC indicates pin 1.
(See Fig. S-1-7.) Be sure this mark matches the
pin 1 on the PCB when positioning for installation.
Then presolder the four corners of the flat pack-IC.
(See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that
none of the pins have solder bridges.
Example :
Pin 1 of the Flat Pack-IC
is indicated by a " " mark.
Fig. S-1-7
To Solid
Mounting Point
CBA
Tweezers
Iron Wire
Soldering Iron
Fig. S-1-5
Fine Tip
Soldering Iron
Flat Pack-IC
or
Presolder
Flat Pack-IC
CBA
Fig. S-1-8
Fig. S-1-6
3-3TVN_SN
Page 12
Instructions for Handling Semiconductors
Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate
with proper grounding (1 MΩ) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
<Correct>
1MΩ
CBA
Grounding Band
1MΩ
CBA
Conductive Sheet or
Copper Plate
3-4TVN_SN
Page 13
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the
cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
[8] Junction
CBA
[9] IR Sensor
CBA
[10] Function
CBA
[1] Stand
Assembly
[2] Rear Cabinet
[3] Inverter CBA
[4] Jack CBA
[5] Power Supply
CBA
[6] Jack Holder
[7] Digital Main
CBA Unit
[12] Speaker
Holder(s)
[13] Speaker(s)
Removal
Step/
Loc.
No.
Part
Fig.
Remove/*Unhook/
Unlock/Release/
No.
Unplug/Unclamp/
Note
Desolder
Digital Main
[7]
CBA UnitD2D4
Junction
[8]
CBA
IR Sensor
[9]
CBA
Function
[10]
CBA
4(S-9), 4(S-10),
*CN3902, Shield Box
D3
Desolder---
D4
D3
(S-11), *CL103A---
D4
D3
------------------
D4
LCD
[11]
Module
D3 5(S-12)---
Assembly
Speaker
[12]
Holder(s)
D3 4(S-13)---
[13] Speaker(s)D3 8(S-14)---
Front
[14]
Cabinet
D3 ------------------
---
[11] LCD Module
Assembly
[14] Front
Cabinet
2. Disassembly Method
Removal
Step/
Loc.
Part
No.
Stand
[1]
Assembly
Rear
[2]
Cabinet
Inverter
[3]
CBA
[4]Jack CBA
Remove/*Unhook/
Fig.
No.
Unlock/Release/
Unplug/Unclamp/
Desolder
D1 3(S-1)---
D1 13(S-2), 2(S-3), 3(S-4)---
5(S-5), *CN1001,
*CN1003, *CN1050,
D2
*CN1100, *CN1150,
D4
*CN1200, *CN1250,
*CN1900
D2
2(S-6), *CL701B---
D4
Note
---
↓
(1)
↓
(2)
↓
(3)
↓
(4)
↓
(5)
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
P = Spring, L = Locking Tab, S = Screw,
H = Hex Screw, CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the
Ta bl e ."
[5]
Power
Supply
CBA
8(S-7), *CN101,
D2
*CN301, *CN302,
D4
*CN801, *CN802
---
[6]Jack Holder D2 2(S-8)---
4-1A91F2DC
Page 14
[2] Rear Cabinet
(S-2)
(S-3)
(S-2)
[1] Stand Assembly
(S-4)
(S-1)
(S-3)
(S-2)
(S-2)
Fig. D1
4-2A91F2DC
Page 15
[3] Inverter CBA
(S-5)
(S-5)
(S-10)
[7] Digital Main
CBA Unit
(S-8)
[4] Jack CBA
Shield Box
[6] Jack Holder
(S-9)
(S-9)
(S-7)
(S-6)
(S-7)
(S-7)
[5] Power Supply CBA
Fig. D2
4-3A91F2DC
Page 16
[14] Front Cabinet
(S-14)
(S-14)
[13] Speaker
[13] Speaker
[12] Speaker
Holder
(S-13)
(S-12)
[12] Speaker
Holder
[9] IR Sensor CBA
(S-13)
[10] Function CBA
[8] Junction
CBA
(S-11)
[11] LCD Module
Assembly
(S-12)
Fig. D3
4-4A91F2DC
Page 17
TV Cable Wiring Diagram
Jack
CBA
Inverter CBA
CN1050
CL701B
CN302
CN301
CN101
Digital Main
CBA Unit
CL701A
CN802
Power Supply CBA
To Speaker
CN602
AC CORD
CN801
Junction
CBA
CN201
CN1100
CN1001
CN1150
CN1200
CN1900
CN1250
CN1003
To LCD Module
Assembly
CN3702
CN3701
CN3902
To LCD Module
Assembly
CL103A
CN101
IR Sensor CBA
CL102C
4-5A91F2DC
CL102A
Function CBA
CL103B
Fig. D4
Page 18
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: “CBA” is abbreviation for
“Circuit Board Assembly.”
Note: Electrical adjustments are required after
replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
Test Equipment Required
1. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
2. Remote control unit
3. Color Analyzer
How to make the Service remote
control unit:
1. Prepare the MAGNAVOX remote control unit.
(Part No. NF800UD or NF802UD)
2. Cut “A” portion of the attached remote control unit
as shown in Fig. 1.
How to set up the service mode:
Service mode:
1. Use the service remote control unit.
2. Turn the power on.
3. Press the service button on the service remote
control unit. The following screen appears.
"*" differs depending on the models.
Code :
***********-***
Pic code :
**-***-**-*****-***
MIPS :
Push 0key
Tuner :
****-*****-****
safety_Non
Safety :
service button
(There is a button under the plastic housing.)
A
Fig. 1
5-1FL9.1PEA
Page 19
1. Purity Check Mode
2. VCOM Adjustment
This mode cycles through full-screen displays of red,
green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service
remote control unit, the display changes as
follows.
Purity Check Mode
White mode
[7] button
[7] button
Black mode
[7] button
Red mode
[7] button
Green mode
[7] button
Blue mode
Test PointAdj. Point
Screen
[CHANNEL UP/DOWN ]
buttons
M. EQ.Spec.
Color analyzerSee below
Figure
To avoid interference from ambinent
light, this adjustment should be
performed in a dark room.
Perpendicularity
L = 3 cm
Color Analyzer
1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical
receptor to the center on the LCD-Panel surface
after zero point calibration as shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the service remote control unit.
5. Press [CHANNEL UP/DOWN] buttons on the
service remote control unit so that the color
analyzer value becomes minimum.
[7] button
White 20% mode
Note:
When entering this mode, the default setting is White mode.
5-2LC7NEA
Page 20
The white balance adjustment should be
performed when replacing the LCD Panel
or Digital CBA.
3. White Balance Adjustment
Purpose: To mix red, green and blue beams correctly
for pure white.
Symptom of Misadjustment: White becomes bluish
or reddish.
Test Point
Screen
Adj. PointModeInput
[VOLUME
DOWN]
button
[VIDEO1]
C/D
M. EQ.Spec.
White Raster
(APL 70%)
or
(APL 40%)
5. [CUTOFF]
Press [1] button to select “COR” for Red Cutoff
adjustment. Press [3] button to select “COB” for
Blue Cutoff adjustment.
[DRIVE]
Press [4] button to select “DR” for Red Drive
adjustment. Press [6] button to select “DB” for Blue
Drive adjustment.
6. In each color mode, press [CHANNEL UP/DOWN]
buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color
temperature becomes 12000°K (x
=
0.272 / y
=
0.278 ±0.005).
Pattern Generator,
Color analyzer
x= 0.272 ± 0.005
y= 0.278 ± 0.005
Figure
To avoid interference from ambinent
light, this adjustment should be
performed in a dark room.
Perpendicularity
L = 3 cm
INPUT: WHITE 70%, 40%
Color Analyzer
1. Operate the unit for more than 20 minutes.
2. Input the White Raster(70%=70IRE, 40%=40IRE).
INPUT SIGNAL
0IRE0IRE
Low
Hight
Light
Light
100IRE
40%=40IRE
70%=70IRE
100IRE
3. Set the color analyzer to the CHROMA mode and
bring the optical receptor to the center on the
LCD-Panel surface after zero point calibration as
shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOLUME DOWN]
button on the service remote control unit and select
“C/D” mode.
5-3LC7NEA
Page 21
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to
select a language and program channels after the set has been initialized.
To put the program back at the factory-default, initialize the LCD TV using the following procedure.
1. Turn the power on.
2. To enter the service mode, press the service
button on the service remote control unit.
- To cancel the service mode, press [POWER]
button on the service remote control unit.
3. Press [INFO] button on the service remote control
unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the
screen. "INITIALIZED" color will change to green
from red when initializing is complete.
6-1A91F3INT
Page 22
FIRMWARE RENEWAL MODE
Equipment Required
a. USB memory
b. Remote Control Unit
Firmware Update Procedure
Note: There are two states (the User Upgrade and
the Factory Upgrade) in firmware update.
User UpgradeUpgrade the firmware only.
The setting values are not
initialized.
Factory upgradeUpgrade the firmware and
initialize the setting values.
The identification of User Upgrade and Factory
Upgrade are done by the filename.
1. Turn the power off and unplug the AC Cord.
2. Insert the USB memory to the USB port as shown
below.
Rear Cabinet
USB Memory
The appearance shown in *1 is described as follows.
AppearanceState
Downloading...
Writing...
Downloading the firmware from
the USB memory.
Writing the downloaded firmware
in flash memory.
Checking...Checking the new firmware.
5. When the firmware update is completed, the
following will appear on the screen.
Software Upgrade
The software upgrade is completed.
Remove USB storage device, unplug and replug power code.
Unplug the AC cord and kindly remove the USB
memory from the USB port. Plug the AC cord in
the wall outlet again and turn the power on.
Note:
When the Factory Upgrade is used, after
restarting TV, shift to initial screen menu in service
mode. "INITIALIZED" will appear on the upper
right of the screen. "INITIALIZED" color will
change to green from red when initializing is
complete.
3. Plug the AC cord in the wall outlet and turn the
power on.
4. The update will start and the following will appear
on the screen.
Software Upgrade
Software upgrade in progress. Please wait.
Do not remove the USB device or turn the TV off
while upgrade is in progress.
*1
Downloading...
0%
Note: If the above screen isn’t displayed, repeat from
step 1.
7-1A91F2FW
Page 23
[ Power Supply Section ]
FLOW CHART NO.1
The power cannot be turned on.
TROUBLESHOOTING
Is the fuse (F601) normal?
Ye s
Is normal state restored when once unplugged
power cord is plugged again several seconds?
Ye s
Is the AL+33V line voltage normal?
Ye s
Check each rectifying circuit of the secondary
circuit and service it if defective.
FLOW CHART NO.2
The fuse blows out.
Check the presence that the primary component
is leaking or shorted and service it if defective.
After servicing, replace the fuse.
FLOW CHART NO.3
When the output voltage fluctuates.
No
No
No
See FLOW CHART No.2 <The fuse blows out.>
Check if there is any leak or short-circuiting on the
primary circuit component, and service it if defective.
(C605, D601, D602, D603, D604, Q601, Q602,
T601)
Check the presence that the rectifying diode or circuit
is shorted in each rectifying circuit of secondary side,
and service it if defective.
Does the photocoupler circuit on the
secondary side operate normally?
Ye s
Check IC601, D609, D611 and their periphery,
circuit and service it if defective.
FLOW CHART NO.4
When buzz sound can be heard in the vicinity of power circuit.
Check if there is any short-circuit on the rectifying diode and the circuit
and service it if defective. (IC631, Q207, Q209, Q210
D631, D632, D633, D638, D641, D642, D646, D647)
FLOW CHART NO.5
AL+33V is not output.
Is approximately +34V voltage supplied to the
cathode of D638?
Ye s
Check D657, R661 and their periphery circuit, and
service it if defective.
Digital Signal Process Block Diagram
[32PFL3504D/F7 (Serial No. : DS2A**********), 32PFL3514D/F7 (Serial No. : DS2A**********)]
LCD MODULE
ASSEMBLY
LLV1P21
LLV1N20
LLV0P23
LLV0N22
LLV2P19
LLV2N18
LLV3P13
LLV3N12
LLV4P11
LLV4N10
LLV5P9
LLV5N8
LLVCLKP16
LLVCLKN15
TP6
POL5
CPV4
OE3
STV1
CN3902
AUDIO SIGNAL
VIDEO SIGNAL
IC3201
DATA(0-15)
H1,H3,H7,H9
B1,B9,C2,C8,
F1,F9,G2,G8,
M2,M3,M7,M8,
D1,D3,D7,D9,
ADDESS(0-12)
N2,N3,N7,N8,
P2,P3,P7,P8,R2
AD23
AD24
AE23
AF23
AF22
AE22
AD21
AD22
AE21
AF21
AF20
AE20
AF24
AE24
W25
TP
W23
POL
Y24
CPV
Y23
OE
(DDR2 SDRAM)
Y22
STV
IC3301 (DIGITAL SIGNAL PROCESS)
V3
U3
AA3
VIDEO-IN
S-VIDEO-Y-IN
S-VIDEO-C-IN
LVD S T X
A/D
CONVERTER
SW
V1
U2
U1
COM-VIDEO-Y-IN
COM-VIDEO-Pr-IN
COM-VIDEO-Pb-IN
DEMODULATOR
/MPEG DECODER
IF-AGC
AF7
AF2
AE2
S-VIDEO-SWM2AUDIO(R)
DIF-OUT1
DIF-OUT2
IF-AGC
S-VIDEO-SW
C6
M1
AUDIO(L)
AD9
BCLK
AD12
ACLK
LRCLK
AUDIO I/F
AD10
SPDIF
AD11
ADATA0
A13-15,A18,
A21-23,B13-15,
B17,B19-23
C15,C17-19,
C23,C24,D14,
D15,D17-19,
D22,D23
DIGITAL
SIGNAL
PROCESS
AUDI O
DECODER
VIDEO
DECODER
HDMI
I/F
A9
B9
B8
A8
C8
C9
B10
A10
AC10
AD14
ADATA1
A11
B11
A5
B5
C4
C5
B4A4B6A6A7
B7
B1
B2
C1C2D1
D2
A1A2A3
B3
DIGITAL MAIN CBA UNIT
TO VIDEO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
TO AUDI O
BLOCK DIAGRAM
TMDS-D0(+)
JK3701
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
79461
9-5
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
3
101216
HDMI-IN1
SDA
SCL
TMDS-CLOCK(-)
15
TMDS-D0(+)
JK3702
79461
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
3
101216
HDMI-IN2
TMDS-CLOCK(-)
SDA
SCL
15
TMDS-D0(+)
JK3703
TMDS-D0(-)
TMDS-D1(+)
TMDS-D1(-)
79461
TMDS-D2(+)
TMDS-D2(-)
TMDS-CLOCK(+)
TMDS-CLOCK(-)
3
101216
HDMI-IN3
A91FJBLD
SDA
SCL
15
Page 37
Inverter Block Diagram
BACK
1
CN1050
LIGHT
2
786
BACK
LIGHT
1
2
CN1100
786
5
5
BACK
1
CN1150
LIGHT
2
786
BACK
LIGHT
1
2
CN1200
5
786
BACK
LIGHT
LCD MODULE
Q1061
ASSEMBLY
OVER VOLTAGE
PROTECTOR
VCOM
1
2
CN1250
OVER VOLTAGE
PROTECTOR
Q1261
5
786
5
Q1211
CN1003
OVER VOLTAGE
PROTECTOR
10
OVER VOLTAGE
Q1161
OVER VOLTAGE
PROTECTOR
PROTECTOR
Q1111
T1050
2
INV+16V
4
1
SW+16V
Q1801,Q1802,
Q1803,Q1804
SW+16V
Q1800,Q1815
T1100
3
IC1000
4
2
DCT
VCC
(PWM CONTROL)
4
12
Q1004,
Q1005
1
3
SW
3
Q1500
Q1501,
Q1502,
T1150
CURRENT
CONTROL
DRIVE
Q1503
11
15
16
4
2
SWITCH
Q1551,
PWM
Q1550
Q1552,
CONTROL
LOGIC
1
CURRENT
CONTROL
SWITCH
DRIVE
Q1553
8
2
1
T1200
4
3
2
5 6
OSC
1
3
Q1003
T1250
4
3
1
2
Q1001
Q1972
OVER VOLTAGE
PROTECTOR
Q1260
IC1700
(COMPARATOR)
Q1600
13
Q1210
12
14
Q1621
OVER VOLTAGE
9
PROTECTOR
10
8
OVER VOLTAGE
PROTECTOR
Q1160
67523
Q1110
1
OVER VOLTAGE
PROTECTOR
Q1060
675
IC1750
(COMPARATOR)
OVER VOLTAGE
PROTECTOR
10
11
23457
T1950
NOTE:
HOT CIRCUIT. BE CAREFUL.
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CN1900
ACL2
HOT-GND1
TO POWER
SUPPLY
BLOCK
DIAGRAM
(CN602)
14
15
8
IC1930
Q1930
SWITCHING
Q1970
14
32
Q1932
IC1931
14
Q1931
32
COLD
HOT
9-6
Q1971
CN1001
PROTECT3
10
TO SYSTEM
BACKLIGHT-ADJ
VCOM
BACKLIGHT-SW
2
12
11
CONTROL
BLOCK
DIAGRAM
(CN201)
INVERTER CBA
A91F2BLINV
Page 38
Power Supply Block Diagram
LCD+16V
LCD+6.8V
INV+16V
VGH
P-ON+3.3V
P-ON+3V
P-ON+7V
AL+3.3V
P-ON+3.3V
P-ON+5V
AL+33V
P-ON+9V
P-ON+5V
AL+13V
AL+3.3V
TUNER+5V
TO SYSTEM
CONTROL
P-ON-H1
P-ON-H2
BLOCK
DIAGRAM
PROTECT2
PROTECT1
INVERTER CBA
DIGITAL MAIN CBA UNIT
2
13
12
10
8,9
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
LCD-6.8V13
P-ON+3.3V12
INV+16V2
VGH10
LCD+16V8,9
CN201CN1001
*1
SW-6.8V
Q211
Q201, Q202,
Q212
For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
Q210
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
CN301CN3701
SW
SW+24.5V
16
10
P-ON+7V16
P-ON+3V10
SWITCHING
Q207,Q208
21,22
AL+3.3V21,22
19,20
P-ON+3.3V19,20
13,14
P-ON+5V13,14
Q401
Q501
SW+16V
32PFL3504D/F7 (Serial No. : DS2A**********),
32PFL3514D/F7 (Serial No. : DS2A**********)
*1
SW+16V
Q209,D204
Q642
SW+9V
SW+3.3V
Q637,D666
SWITCHING
Q638,Q639
Q640
SW+5V
Q634
SW+5V
Q641,643
IC631
Q635
23
REG.
+3.3V
+5V REG.
4A/125V
11
14
12
17
18
4A/125V
4
CN602
TO
INVERTER
ACL2
HOT-GND1
BLOCK
DIAGRAM
(CN1900)
3
T601
BRIDGE
RECTIFIER
D601- D604
LINE
FILTER
L602
LINE
FILTER
L601
F601
4A/125V
HOT CIRCUIT. BE CAREFUL.
AC601
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
AC CORD
5
13
9-7
FEED
16
15
19
14
7
9
8
IC601
BACK
Q631
32
HOTCOLD
CONTROL
Q602
SWITCHING
POWER SUPPLY CBA
SWITCHING
Q601
A91F2BLP
Page 39
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis
have special characteristics. These characteristics
often pass unnoticed and the protection afforded by
them cannot necessarily be obtained by using
replacement components rated for higher voltage,
wattage, etc. Replacement parts that have these
special safety characteristics are identified in this
manual and its supplements; electrical components
having such features are identified by the mark “#” in
the schematic diagram and the parts list. Before
replacing any of these components, read the parts list
in this manual carefully. The use of substitute
replacement parts that do not have the same safety
characteristics as specified in the parts list may create
shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these
drawings for ordering. The correct part number is
shown in the parts list, and may be slightly
different or amended since these drawings were
prepared.
2. All resistance values are indicated in ohms
(K = 10
3. Resistor wattages are 1/4W or 1/6W unless
otherwise specified.
4. All capacitance values are indicated in µF
(P = 10
5. All voltages are DC voltages unless otherwise
specified.
6. This schematic diagrams are masterized version
that should cover the entire FL9.1 chassis models.
Thus some parts in detail illustrated on this
schematic diagrams may vary depend on the
model within the FL9.1 chassis.
Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service
manual is the latest version for this chassis at the
moment of making this service manual.
Depend on the mass production date of each
model, the actual layout of each Board may differ
slightly from this version.
3
, M = 106).
-6
µF).
10-1FL9_1_SC
Page 40
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON
r
THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:
Plug the TV power cord into a standard AC outlet.:
2
(Unit: Volt)
1
5.05.0
3
Power on mode
5. How to read converged lines
1-D3
Distinction Area
Line Number
(1 to 3 digits)
Examples:
1. "1-D3" means that line number "1" goes to the line numbe
"1" of the area "D3".
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
6. Test Point Information
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
Voltage
Indicates that the voltage
is not consistent here.
3
2
1
AREA D3
1-B1
AREA B1
1-D3
ABCD
10-2FL9_1_SC
Page 41
Power Supply 1/4 Schematic Diagram
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
10-3
A91F2SCM1
Page 42
Power Supply 2/4 Schematic Diagram
10-4
A91F2SCM2
Page 43
Power Supply 3/4 & Jack Schematic Diagram
10-5
A91F2SCM3
Page 44
Power Supply 4/4 Schematic Diagram
10-6
A91F2SCM4
Page 45
Inverter Schematic Diagram
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-7
A91F2SCINV
Page 46
Function Schematic Diagram
10-8
A91F2SCF
Page 47
IR Sensor & Junction Schematic Diagram
10-9
A91F2SCIR
Page 48
Digital Main 1/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-10
A91F2SCD1
Page 49
Digital Main 2/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-11
A91F2SCD2
Page 50
Digital Main 3/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-12
A91F2SCD3
Page 51
Digital Main 4/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-13
A91F2SCD4
Page 52
Digital Main 5/5 Schematic Diagram
1 NOTE:
The order of pins shown in this diagram is different from that of actual IC3301.
IC3301 is divided into five and shown as IC3301 (1/5) ~ IC3301 (5/5) in this Digital Main Schematic Diagram Section.
10-14
A91F2SCD5
Page 53
Power Supply CBA Top View
For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
4A/125V
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
10-15
BA94F0F01024-A
Page 54
Power Supply CBA Bottom View
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
4A/125V
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.
For continued protection against risk of fire,
replace only with same type 4 A, 125V fuse.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
WF1
PIN 4 OF
CN302
WF3
PIN 6 OF
CN302
WF2
PIN 8 OF
CN302
WF7
PIN 13 OF
CN302
WF4
PIN 15 OF
CN302
WF5
PIN 17 OF
CN302
WF6
PIN 19 OF
CN302
10-16
BA94F0F01024-A
Page 55
Inverter CBA Top View
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-17
BA91F2F01031-A
Page 56
Inverter CBA Bottom View
Because a hot chassis ground is present in the power
supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
10-18
BA91F2F01031-A
Page 57
Function CBA Top View
Junction CBA
Junction CBA
Top View
Bottom View
BA91F2F01031
Function CBA Bottom View
10-19
BA91F2F01031-B
Page 58
IR Sensor CBA Top View
Jack CBA Top View
IR Sensor CBA Bottom View
Jack CBA Bottom View
BA91F2F01031-C
BA94F0F01024-B
10-20
Page 59
WAVEFORMS
WF1 ~ WF7 = Waveforms to be observed at
Waveform check points.
(Shown in Schematic Diagram.)
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTE: Parts that are not assigned part numbers
(---------) are not available.
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%D.....±0.5%F.....±1%
G.....±2%J......±5%K.....±10%
M.....±20%N.....±30%Z.....+80/-20%
DIGITAL MAIN CBA UNIT
Ref. No.DescriptionPart No.
DIGITAL MAIN CBA UNITA91F2MMA-004
MPW CBA
Ref. No.DescriptionPart No.
MPW CBA
Consists of the following:
POWER SUPPLY CBA(MPW-1)
JACK CBA(MPW-2)
POWER SUPPLY CBA(MPW-1)
Ref. No.DescriptionPart No.
POWER SUPPLY CBA(MPW-1)
Consists of the following:
CAPACITORS
C201CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C202CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C203CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C204ELECTROLYTIC CAP. 2.2µF/50V MCE1JMASDL2R2
C210ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C216CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C217CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C218CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C219ELECTROLYTIC CAP. 47µF/25V MCE1EMASDL470
C221CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C222ELECTROLYTIC CAP. 470µF/25V MCE1EMASDL471
C223ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C224ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C302CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C303ELECTROLYTIC CAP. 330µF/10V MCE1AMASDL331
C305CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
C306ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL1R0
C309CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C776CHIP CERAMIC CAP.(1608) CH J 100pF/50VCHD1JJ3CH101
C801CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C802CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C803CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C804CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C805CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C806CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C807CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
100V J
100V J
100V J
100V J
100V J
CA2A473DT018
CA2A122DT018
CA2A683DT018
CA2A152DT018
CA2A222DT018
2009101315-1A91F2EL
Page 70
Ref. No.DescriptionPart No.
C808CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C809CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C810CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C811CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C815CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C816ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C817CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C818CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C819ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C820CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C821CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C822CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C823ELECTROLYTIC CAP. 1000µF/25V MCE1EMZNDL102
C824CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C825CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C826CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C827ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C828CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C829CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C830CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C832ELECTROLYTIC CAP. 3.3µF/50V MCE1JMASDL3R3
C833CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C834CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C835CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C836CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C837CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C839CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C841CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C842CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C843CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C844ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C846CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C847CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C871CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C872CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C873CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C874CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C877CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C878CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C879CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C880ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C882CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C883CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C884CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C885CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
L601#COIL LINE FILTER ST0807ET28-009 10MHLLEG0Z0Y2029
L602#COIL LINE FILTER ST0807ET28-009 10MHLLEG0Z0Y2029
L801RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
L802RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
L803RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
L804RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
L871WIRE COPPER 6111-06003-0120XZ40C0SHG002
TRANSISTORS
Q172TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q201TRANSISTOR KTA1267-GR-AT/PNQS1KTA1267P
Q203TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q204TRANSISTOR KTA1267-GR-AT/PNQS1KTA1267P
Q205TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q207TRANSISTOR KTA1267-GR-AT/PNQS1KTA1267P
Q208TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q209TRANSISTOR 2SD400(E)QQUE002SD400
Q210TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q211TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q212TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q401TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q402TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q501TRANSISTOR 2SC2120-Y(TE2 F T)QQSY2SC2120F
Q601#FET MOS 2SK3563(Q)QFWZ2SK3563Q
Q602#TRANSISTOR 2SC2120-O(TE2 F T)QQS02SC2120F
Q631TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q634TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q635TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q636TRANSISTOR 2SA950-O (TE2 F T)QQS002SA950F
Q637NPN TRANSISTOR POWER 2SC4881F HFE
Q638TRANSISTOR KTA1267-GR-AT/PNQS1KTA1267P
Q639TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q640TRANSISTOR 2SC2120-Y(TE2 F T)QQSY2SC2120F
Q641TRANSISTOR 2SC2120-Y(TE2 F T)QQSY2SC2120F
Q642TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q643TRANSISTOR 2SC2120-Y(TE2 F T)QQSY2SC2120F
Q771TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q772TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q801TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q802TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q841TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q871TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q872TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q873TRANSISTOR KTC3198-Y-AT/PNQSYKTC3198P
Q874TRANSISTOR KTA1267-GR-AT/PNQS1KTA1267P
MAX320
QQWZ2SC4881F
RESISTORS
R174CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
Ref. No.DescriptionPart No.
R201CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R206CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R207CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R208CHIP RES. 1/10W J 1 ΩRRXAJR5Z01R0
R209CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R210RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R211CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R212RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R213CHIP RES. 1/10W J 100k ΩRRXAJR5Z0104
R214CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R216CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R217CHIP RES. 1/10W J 1.5k ΩRRXAJR5Z0152
R218CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R219CHIP RES. 1/10W J 15k ΩRRXAJR5Z0153
R220CHIP RES. 1/10W J 1k ΩRRXAJR5Z0102
R223RES CARBON FILM T 1/4W J 3.3k ΩRCX4332T1001
R224RES CARBON FILM T 1/4W J 27k ΩRCX4273T1001
R225CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R226CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R227METAL OXIDE FILM RES. 1W J 2.7 ΩRN012R7ZU001
R228RES CARBON FILM T 1/4W J 2.7k ΩRCX4272T1001
R229RES CARBON FILM T 1/4W J 2.7k ΩRCX4272T1001
R231CHIP RES. 1/10W J 1.5k ΩRRXAJR5Z0152
R232CHIP RES. 1/10W F 11k ΩRRXAFR5H1102
R233CHIP RES. 1/10W F 750 ΩRRXAFR5H7500
R234CHIP RES. 1/10W F 2.2k ΩRRXAFR5H2201
R235RES CARBON FILM T 1/4W J 330 ΩRCX4331T1001
R236RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R237RES CARBON FILM T 1/4W J 8.2k ΩRCX4822T1001
R238RES CARBON FILM T 1/4W J 1.5k ΩRCX4152T1001
R240RES CARBON FILM T 1/4W J 47k ΩRCX4473T1001
R241CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R242RES CARBON FILM T 1/4W J 12k ΩRCX4123T1001
R243RES CARBON FILM T 1/4W J 220 ΩRCX4221T1001
R245RES CARBON FILM T 1/4W J 8.2k ΩRCX4822T1001
R247METAL OXIDE FILM RES. 1W J 2.7 ΩRN012R7ZU001
R248CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R249RES CARBON FILM T 1/4W J 1.0k ΩRCX4102T1001
R301CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R302CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R303CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R304CHIP RES. 1/10W J 47 ΩRRXAJR5Z0470
R305CHIP RES. 1/10W J 47 ΩRRXAJR5Z0470
R311CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R401CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R402RES CARBON FILM T 1/4W J 22k ΩRCX4223T1001
R403CHIP RES. 1/10W J 47k ΩRRXAJR5Z0473
R404CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R405RES CARBON FILM T 1/4W J 47k ΩRCX4473T1001
R407RES CARBON FILM T 1/4W J 22k ΩRCX4223T1001
R408CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R410CHIP RES. 1/10W F 8.2k ΩRRXAFR5H8201
R411CHIP RES. 1/10W F 36k ΩRRXAFR5H3602
R412CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R501RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R601#RES. CARBON FILM J 1/2W J 560k ΩRCX2564T1003
R602#CEMENT RESISTOR 5W J 2.2 Ω H 10MMRW052R2PAK10
R604RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R605RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R606RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R610RES CARBON FILM T 1/4W J 180 ΩRCX4181T1001
R611RES CARBON FILM T 1/4W J 180 ΩRCX4181T1001
R613RES CARBON FILM T 1/4W J 1.2k ΩRCX4122T1001
2009101315-3A91F2EL
Page 72
Ref. No.DescriptionPart No.
R614#METAL OXIDE FILM RES. 2W J 0.39 ΩRN02R39ZU001
R615RES CARBON FILM T 1/4W J 3.9k ΩRCX4392T1001
R616RES CARBON FILM T 1/4W J 220 ΩRCX4221T1001
R617#CEMENT RESISTOR 5W J 2.2 Ω H 10MMRW052R2PAK10
R618RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R637RES CARBON FILM T 1/4W J 1.2k ΩRCX4122T1001
R638RES CARBON FILM T 1/4W J 1.5k ΩRCX4152T1001
R639RES CARBON FILM T 1/4W J 1.5k ΩRCX4152T1001
R641RES CHIP.(1608) 1/10W D 1.1k ΩRRXADR5H1101
R642RES CHIP.(1608) 1/10W D 10k ΩRRXADR5H1002
R643RES CHIP.(1608) 1/10W D 10k ΩRRXADR5H1002
R644CHIP RES. 1/10W F 820 ΩRRXAFR5H8200
R645RES CARBON FILM T 1/4W J 270 ΩRCX4271T1001
R646RES CARBON FILM T 1/4W J 180 ΩRCX4181T1001
R648CHIP RES. 1/10W F 1.0k ΩRRXAFR5H1001
R650RES CARBON FILM T 1/4W J 4.7k ΩRCX4472T1001
R651CHIP RES. 1/10W J 1 ΩRRXAJR5Z01R0
R652CHIP RES. 1/10W F 24k ΩRRXAFR5H2402
R660WIRE COPPER 6111-06003-0120XZ40C0SHG002
R661RES. CARBON FILM J 1/2W J 390 ΩRCX2391T1003
R662RES CARBON FILM T 1/4W J 15 ΩRCX4150T1001
R663RES CARBON FILM T 1/4W J 1.8k ΩRCX4182T1001
R664RES CARBON FILM T 1/4W J 1.8k ΩRCX4182T1001
R665WIRE COPPER 6111-06003-0120XZ40C0SHG002
R666RES CARBON FILM T 1/4W J 1.0 ΩRCX41R0T1001
R667WIRE COPPER 6111-06003-0120XZ40C0SHG002
R668CHIP RES. 1/10W F 620 ΩRRXAFR5H6200
R669CHIP RES. 1/10W F 1.0k ΩRRXAFR5H1001
R670WIRE COPPER 6111-06003-0120XZ40C0SHG002
R671WIRE COPPER 6111-06003-0120XZ40C0SHG002
R672METAL OXIDE RES. 1W J 0.33 ΩRN01R33ZU001
R673RES CARBON FILM T 1/4W J 22k ΩRCX4223T1001
R674RES CARBON FILM T 1/4W J 1.0k ΩRCX4102T1001
R675CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R676CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R677RES CARBON FILM T 1/4W J 270 ΩRCX4271T1001
R678RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R679CHIP RES. 1/10W F 3.3k ΩRRXAFR5H3301
R680CHIP RES. 1/10W F 10k ΩRRXAFR5H1002
R682RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
R683RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
R685RES CARBON FILM T 1/4W J 22 ΩRCX4220T1001
R686RES CARBON FILM T 1/4W J 1.0k ΩRCX4102T1001
R687RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R688RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R689RES CARBON FILM T 1/4W J 1.2k ΩRCX4122T1001
R691RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
R692RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
--------------------------------------------------------------------FUNCTION CBA
IR SENSOR CBA
JUNCTION CBA
INVERTER CBA
Ref. No.DescriptionPart No.
INVERTER CBA
Consists of the following:
CAPACITORS
C1000ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C1001CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1002CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1003CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1004CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1005CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1006CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1007CHIP CERAMIC CAP.(1608) B K 0.22µF/16VCHD1CK30B224
C1008CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1009ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1011CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1012POLYESTER FILM CAP. (PB FREE) 0.0039µF/
C1013CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1045METALIZED POLYESTER FILM CAP. 0.47µF/
C1050CERAMIC CAP. B K 0.01µF/1KVCCD3AKP0B103
C1051CERAMIC CAP. B K 0.01µF/1KVCCD3AKP0B103
C1061CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1062CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1063ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1064CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1065CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1066CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1067ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1068CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1072CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1111CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1112CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1113ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1114CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1115CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1116CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1117ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1118CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1122CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1161CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1162CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1163ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1164CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1165CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1166CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1167ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1168CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1172CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1211CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1212CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1213ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1214CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
100V J
50V J
A91F2M1V-001
A91F2M1V-001-IV
---------------------------A91F2M1V-001-FNIRJN
----------
CA2A392DT018
CT1J474DT040
2009101315-5A91F2EL
Page 74
Ref. No.DescriptionPart No.
C1215CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1216CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1217ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1218CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1222CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1261CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1262CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1263ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1264CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1265CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1266CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1267ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1268CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1272CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1501CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1503CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1510CERAMIC CAP. 470pF/2KVCA3D471PAN04
C1511CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1530CERAMIC CAP. 470pF/2KVCA3D471PAN04
C1531CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1600CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1620CHIP CERAMIC CAP.(1608) B K 1000pF/50VCHD1JK30B102
C1700CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1701CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1750CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1751CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1800ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C1801ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C1802CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1930CERAMIC CAP. 1000pF/2KVCA3D102PAN04
C1931# POLYESTER FILM CAP. (PB FREE) 0.001µF/
C1932POLYESTER FILM CAP. (PB FREE) 0.027µF/
C1933POLYESTER FILM CAP. (PB FREE) 0.1µF/100V JCA2A104DT018
C1941CERAMIC CAP. B K 0.01µF/1KVCCD3AKP0B103
C1970POLYESTER FILM CAP. (PB FREE) 0.047µF/
C1981CHIP CERAMIC CAP. F Z 0.01µF/50VCHD1JZ30F103
C1982ELECTROLYTIC CAP. 0.47µF/50V MCE1JMASDLR47
C1990CERAMIC CAP. B K 1500pF/1KVCCD3AKP0B152
C1992# ELECTROLYTIC CAP 470µF/100VCE2AMZNDL471
C1993ELECTROLYTIC CAP 220µF/100VCE2AMZNDL221
C1994ELECTROLYTIC CAP 220µF/100VCE2AMZNDL221
CN101242 SERIES CONNECTOR TUC-P08X-B1 WHT STJCTUB08TG002
----------
FUNCTION CBA
Ref. No.DescriptionPart No.
FUNCTION CBA
Consists of the following:
----------
CAPACITOR
C108CAP CERAMIC (AX) 0.1µF/50V/F/ZCA1J104TU062
RESISTORS
R108RES CARBON FILM T 1/4W J 220 ΩRCX4221T1001
R109RES CARBON FILM T 1/4W G 10k ΩRCX4103T1002
R111RES CARBON FILM T 1/4W G 4.7k ΩRCX4472T1002
R112RES CARBON FILM T 1/4W G 2.7k ΩRCX4272T1002
R113RES CARBON FILM T 1/4W G 4.7k ΩRCX4472T1002
R114RES CARBON FILM T 1/4W G 8.2k ΩRCX4822T1002
R115RES CARBON FILM T 1/4W G 18k ΩRCX4183T1002
SWITCHES
SW101BTACT SWITCH SKQSABSST0101AL038
SW103BTACT SWITCH SKQSABSST0101AL038
SW104BTACT SWITCH SKQSABSST0101AL038
SW105BTACT SWITCH SKQSABSST0101AL038
SW106BTACT SWITCH SKQSABSST0101AL038
SW107BTACT SWITCH SKQSABSST0101AL038
IR SENSOR CBA
Ref. No.DescriptionPart No.
IR SENSOR CBA
Consists of the following:
CAPACITORS
C101ELECTROLYTIC CAP. 47µF/16V M H7CE1CMAVSL470
C103CHIP CERAMIC CAP. CH J 330pF/50VCHD1JJ3CH331
C104CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
----------
2009101315-9A91F2EL
Page 78
ELECTRICAL PARTS LIST
[32PFL3504D/F7 (Serial No. : YA1A**********)]
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%D.....±0.5%F.....±1%
G.....±2%J......±5%K.....±10%
M.....±20%N.....±30%Z.....+80/-20%
DIGITAL MAIN CBA UNIT
Ref. No.DescriptionPart No.
DIGITAL MAIN CBA UNITA91F2MMA-004
MPW CBA
Ref. No.DescriptionPart No.
MPW CBA
Consists of the following:
POWER SUPPLY CBA(MPW-1)
JACK CBA(MPW-2)
POWER SUPPLY CBA(MPW-1)
Ref. No.DescriptionPart No.
POWER SUPPLY CBA(MPW-1)
Consists of the following:
CAPACITORS
C201CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C202CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C203CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C204ELECTROLYTIC CAP. 2.2µF/50V MCE1JMASDL2R2
C210ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C216CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C217CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C218CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C219ELECTROLYTIC CAP. 47µF/25V MCE1EMASDL470
C221CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C222ELECTROLYTIC CAP. 470µF/25V MCE1EMASDL471
C223ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C224ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C302CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C303ELECTROLYTIC CAP. 1000µF/6.3V MCE0KMASDL102
C305CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
C306ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL1R0
C309CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C310CHIP CERAMIC CAP.(1608) CH J 47pF/50VCHD1JJ3CH470
C311CHIP CERAMIC CAP.(1608) CH J 47pF/50VCHD1JJ3CH470
C402CHIP CERAMIC CAP.(1608) B K 0.033µF/50VCHD1JK30B333
A91F2MPW-001
----------
----------
----------
Ref. No.DescriptionPart No.
C501ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C601#CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004
C602#CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004
C605CAP ELECTROLYTIC 470µF/200V MCA2D471DYG07
C609POLYESTER FILM CAP. (PB FREE) 0.047µF/
C610POLYESTER FILM CAP. (PB FREE) 0.0012µF/
C611CERAMIC CAP. 470pF/2KVCA3D471PAN04
C612POLYESTER FILM CAP. (PB FREE) 0.068µF/
C647ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL1R0
C648ELECTROLYTIC CAP. 100µF/10V MCE1AMASDL101
C652ELECTROLYTIC CAP. 1000µF/6.3V MCE0KMASDL102
C653ELECTROLYTIC CAP. 220µF/10V MCE1AMASDL221
C654ELECTROLYTIC CAP. 220µF/10V MCE1AMASDL221
C656ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C657ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C676ELECTROLYTIC CAP. 2.2µF/50V MCE1JMASDL2R2
C681CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C682CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C683CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C684CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C691#SAFTY CAP. 1000pF/250V KXCA2E102MR101
C693#SAFTY CAP. 1000pF/250V KXCA2E102MR101
C723CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C724CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C731CHIP CERAMIC CAP. CH J 39pF/50VCHD1JJ3CH390
C732CHIP CERAMIC CAP. CH J 39pF/50VCHD1JJ3CH390
C733CHIP CERAMIC CAP. CH J 39pF/50VCHD1JJ3CH390
C734CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
C735CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
C736CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
C743CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C744CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C771ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C772CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C775CHIP CERAMIC CAP.(1608) CH J 100pF/50VCHD1JJ3CH101
C776CHIP CERAMIC CAP.(1608) CH J 100pF/50VCHD1JJ3CH101
C801CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C802CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C803CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C804CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C805CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C806CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
100V J
100V J
100V J
100V J
100V J
CA2A473DT018
CA2A122DT018
CA2A683DT018
CA2A152DT018
CA2A222DT018
2009100515-10A91FQEL
Page 79
Ref. No.DescriptionPart No.
C807CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C808CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C809CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C810CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C811CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C815CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C816ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C817CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C818CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C819ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C820CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C821CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C822CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C823ELECTROLYTIC CAP. 1000µF/25V MCE1EMZNDL102
C824CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C825CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C826CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C827ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C828CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C829CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C830CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C832ELECTROLYTIC CAP. 3.3µF/50V MCE1JMASDL3R3
C833CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C834CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C835CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C836CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C837CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C838CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C839CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C841CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C842CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C843CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C844ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C845CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C846CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C847CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C871CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C872CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C873CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C874CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C875CHIP CERAMIC CAP.(1608) CH J 270pF/50VCHD1JJ3CH271
C876CHIP CERAMIC CAP.(1608) CH J 270pF/50VCHD1JJ3CH271
C877CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C878CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C879CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C880ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C882CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C883CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C884CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C885CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
JK751JACK SW DIN PCB L DIN-435C(777D)JYEL040YUQ03
JK752JACK RCA PCB L RCA-101S(1)-03JXRL010YUQ12
JK753JACK RCA PCB L RCA-101S(1)-04JXRL010YUQ13
----------
Ref. No.DescriptionPart No.
JK754JACK SW RCA PCB L RCA-102F(RD)JYRL010YUQ05
INVERTER ASSEMBLY
Ref. No.DescriptionPart No.
INVERTER ASSEMBLY
Consists of the following:
INVERTER CBA
--------------------------------------------------------------------FUNCTION CBA
IR SENSOR CBA
JUNCTION CBA
INVERTER CBA
Ref. No.DescriptionPart No.
INVERTER CBA
Consists of the following:
CAPACITORS
C1000ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C1001CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1002CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1003CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1004CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1005CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1006CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1007CHIP CERAMIC CAP.(1608) B K 0.22µF/16VCHD1CK30B224
C1008CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1009ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1011CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1012POLYESTER FILM CAP. (PB FREE) 0.0039µF/
C1013CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1045METALIZED POLYESTER FILM CAP. 0.47µF/
C1050CERAMIC CAP. B K 0.01µF/1KVCCD3AKN0B103
C1051CERAMIC CAP. B K 0.01µF/1KVCCD3AKN0B103
C1061CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1062CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1063ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1064CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1065CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1066CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1067ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1068CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1072CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1111CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1112CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1113ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1114CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1115CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1116CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1117ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1118CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1122CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1161CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1162CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1163ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1164CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1165CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1166CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1167ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1168CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1172CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1211CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
100V J
50V J
A91FQM1V-001
A91FQM1V-001-IV
---------------------------A91FQM1V-001-FNIRJN
----------
CA2A392DT018
CT1J474DT040
2009100515-14A91FQEL
Page 83
Ref. No.DescriptionPart No.
C1212CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1213ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1214CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1215CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1216CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1217ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1218CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1222CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1261CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1262CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1263ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1264CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1265CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1266CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1267ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1268CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1272CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1501CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1503CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1510CERAMIC CAP. 470pF/2KVCA3D471PAN04
C1511CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1530CERAMIC CAP. 470pF/2KVCA3D471PAN04
C1531CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1600CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1620CHIP CERAMIC CAP.(1608) B K 1000pF/50VCHD1JK30B102
C1700CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1701CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1750CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1751CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1800ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C1801ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C1802CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1905# SAFTY CAP. 2200pF/250V KXCA2E222MR101
C1910CAP ELECTROLYTIC 270µF/200VCEA271DYG005
C1930CERAMIC CAP. 1000pF/2KVCA3D102PAN04
C1931# POLYESTER FILM CAP. (PB FREE) 0.001µF/
C1932POLYESTER FILM CAP. (PB FREE) 0.027µF/
C1933POLYESTER FILM CAP. (PB FREE) 0.1µF/100V JCA2A104DT018
C1941CERAMIC CAP. B K 0.01µF/1KVCCD3AKN0B103
C1970POLYESTER FILM CAP. (PB FREE) 0.047µF/
C1981CHIP CERAMIC CAP. F Z 0.01µF/50VCHD1JZ30F103
C1982ELECTROLYTIC CAP. 0.47µF/50V MCE1JMASDLR47
C1990CERAMIC CAP. 1500pF/1KVCCD3AKA0R152
C1992# ELECTROLYTIC CAP 470µF/100VCE2AMZNDL471
C1993ELECTROLYTIC CAP 220µF/100VCE2AMZNDL221
C1994ELECTROLYTIC CAP 220µF/100VCE2AMZNDL221
C101ELECTROLYTIC CAP. 47µF/16V M H7CE1CMAVSL470
C103CHIP CERAMIC CAP. CH J 330pF/50VCHD1JJ3CH331
C104CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
C105CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
CN101242 SERIES CONNECTOR TUC-P08X-B1 WHT STJCTUB08TG002
----------
FUNCTION CBA
Ref. No.DescriptionPart No.
FUNCTION CBA
Consists of the following:
CAPACITOR
C108CAP CERAMIC (AX) 0.1µF/50V/F/ZCA1J104TU062
RESISTORS
R108RES CARBON FILM T 1/4W J 220 ΩRCX4221T1001
R109RES CARBON FILM T 1/4W G 10k ΩRCX4103T1002
R111RES CARBON FILM T 1/4W G 4.7k ΩRCX4472T1002
R112RES CARBON FILM T 1/4W G 2.7k ΩRCX4272T1002
R113RES CARBON FILM T 1/4W G 4.7k ΩRCX4472T1002
R114RES CARBON FILM T 1/4W G 8.2k ΩRCX4822T1002
R115RES CARBON FILM T 1/4W G 18k ΩRCX4183T1002
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%D.....±0.5%F.....±1%
G.....±2%J......±5%K.....±10%
M.....±20%N.....±30%Z.....+80/-20%
DIGITAL MAIN CBA UNIT
Ref. No.DescriptionPart No.
DIGITAL MAIN CBA UNITA91F2MMA-004
MPW CBA
Ref. No.DescriptionPart No.
MPW CBA
Consists of the following:
POWER SUPPLY CBA(MPW-1)
JACK CBA(MPW-2)
POWER SUPPLY CBA(MPW-1)
Ref. No.DescriptionPart No.
POWER SUPPLY CBA(MPW-1)
Consists of the following:
CAPACITORS
C201CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C202CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C203CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C204ELECTROLYTIC CAP. 2.2µF/50V MCE1JMASDL2R2
C210ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C216CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C217CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C218CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C219ELECTROLYTIC CAP. 47µF/25V MCE1EMASDL470
C221CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C222ELECTROLYTIC CAP. 470µF/25V MCE1EMASDL471
C223ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C224ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C302CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C303ELECTROLYTIC CAP. 1000µF/6.3V MCE0KMASDL102
C305CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
C306ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL1R0
C309CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C776CHIP CERAMIC CAP.(1608) CH J 100pF/50VCHD1JJ3CH101
C801CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C802CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C803CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C804CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C805CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C806CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C807CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
100V J
100V J
100V J
100V J
100V J
CA2A473DT018
CA2A122DT018
CA2A683DT018
CA2A152DT018
CA2A222DT018
2009101315-19A91FAEL
Page 88
Ref. No.DescriptionPart No.
C808CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C809CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C810CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C811CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C815CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C816ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C817CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C818CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C819ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C820CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C821CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C822CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C823ELECTROLYTIC CAP. 1000µF/25V MCE1EMZNDL102
C824CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C825CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C826CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C827ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C828CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C829CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C830CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C832ELECTROLYTIC CAP. 3.3µF/50V MCE1JMASDL3R3
C833CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C834CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C835CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C836CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C837CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C839CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C841CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C842CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C843CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C844ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C846CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C847CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C871CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C872CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C873CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C874CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C877CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C878CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C879CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C880ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C882CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C883CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C884CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C885CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
L601#COIL LINE FILTER ST0807ET28-009 10MHLLEG0Z0Y2029
L602#COIL LINE FILTER ST0807ET28-009 10MHLLEG0Z0Y2029
L801RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
L802RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
L803RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
L804RADIAL LEAD INDUCTORS 33µHLLARKGQTU330
R206CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R207CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R208CHIP RES. 1/10W J 1 ΩRRXAJR5Z01R0
R209CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R210RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R211CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R212RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R213CHIP RES. 1/10W J 100k ΩRRXAJR5Z0104
R214CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R216CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R217CHIP RES. 1/10W J 1.5k ΩRRXAJR5Z0152
R218CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R219CHIP RES. 1/10W J 15k ΩRRXAJR5Z0153
R220CHIP RES. 1/10W J 1k ΩRRXAJR5Z0102
R223RES CARBON FILM T 1/4W J 3.3k ΩRCX4332T1001
R224RES CARBON FILM T 1/4W J 27k ΩRCX4273T1001
R225CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R226CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R227METAL OXIDE FILM RES. 1W J 2.7 ΩRN012R7ZU001
R228RES CARBON FILM T 1/4W J 2.7k ΩRCX4272T1001
R229RES CARBON FILM T 1/4W J 2.7k ΩRCX4272T1001
R231CHIP RES. 1/10W J 1.5k ΩRRXAJR5Z0152
R232CHIP RES. 1/10W F 11k ΩRRXAFR5H1102
R233CHIP RES. 1/10W F 750 ΩRRXAFR5H7500
R234CHIP RES. 1/10W F 2.2k ΩRRXAFR5H2201
R235RES CARBON FILM T 1/4W J 330 ΩRCX4331T1001
R236RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R237RES CARBON FILM T 1/4W J 8.2k ΩRCX4822T1001
R238RES CARBON FILM T 1/4W J 1.5k ΩRCX4152T1001
R240RES CARBON FILM T 1/4W J 47k ΩRCX4473T1001
R241CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R242RES CARBON FILM T 1/4W J 12k ΩRCX4123T1001
R243RES CARBON FILM T 1/4W J 220 ΩRCX4221T1001
R245RES CARBON FILM T 1/4W J 8.2k ΩRCX4822T1001
R247METAL OXIDE FILM RES. 1W J 2.7 ΩRN012R7ZU001
R248CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R249RES CARBON FILM T 1/4W J 10k ΩRCX4103T1001
R301CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R302CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R303CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R304CHIP RES. 1/10W J 47 ΩRRXAJR5Z0470
R305CHIP RES. 1/10W J 47 ΩRRXAJR5Z0470
R311CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
R401CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R402RES CARBON FILM T 1/4W J 22k ΩRCX4223T1001
R403CHIP RES. 1/10W J 47k ΩRRXAJR5Z0473
R404CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R405RES CARBON FILM T 1/4W J 47k ΩRCX4473T1001
R407RES CARBON FILM T 1/4W J 22k ΩRCX4223T1001
R408CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R410CHIP RES. 1/10W F 8.2k ΩRRXAFR5H8201
R411CHIP RES. 1/10W F 36k ΩRRXAFR5H3602
R412CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R501RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R601#RES. CARBON FILM J 1/2W J 560k ΩRCX2564T1003
R602#CEMENT RESISTOR 5W J 2.2 Ω H 10MMRW052R2PAK10
R604RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R605RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R606RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R610RES CARBON FILM T 1/4W J 180 ΩRCX4181T1001
R611RES CARBON FILM T 1/4W J 180 ΩRCX4181T1001
R613RES CARBON FILM T 1/4W J 1.2k ΩRCX4122T1001
R614#METAL OXIDE FILM RES. 2W J 0.39 ΩRN02R39ZU001
2009101315-21A91FAEL
Page 90
Ref. No.DescriptionPart No.
R615RES CARBON FILM T 1/4W J 3.9k ΩRCX4392T1001
R616RES CARBON FILM T 1/4W J 220 ΩRCX4221T1001
R617#CEMENT RESISTOR 5W J 2.2 Ω H 10MMRW052R2PAK10
R618RES CARBON FILM T 1/4W J 390k ΩRCX4394T1001
R636RES. CARBON FILM J 1/2W J 2.7 ΩRCX22R7T1003
R637RES CARBON FILM T 1/4W J 1.2k ΩRCX4122T1001
R638RES CARBON FILM T 1/4W J 1.5k ΩRCX4152T1001
R639RES CARBON FILM T 1/4W J 1.5k ΩRCX4152T1001
R641RES CHIP.(1608) 1/10W D 1.1k ΩRRXADR5H1101
R642RES CHIP.(1608) 1/10W D 10k ΩRRXADR5H1002
R643RES CHIP.(1608) 1/10W D 10k ΩRRXADR5H1002
R644CHIP RES. 1/10W F 820 ΩRRXAFR5H8200
R645RES CARBON FILM T 1/4W J 270 ΩRCX4271T1001
R646RES CARBON FILM T 1/4W J 180 ΩRCX4181T1001
R648CHIP RES. 1/10W F 1.0k ΩRRXAFR5H1001
R650RES CARBON FILM T 1/4W J 4.7k ΩRCX4472T1001
R651CHIP RES. 1/10W J 1 ΩRRXAJR5Z01R0
R652CHIP RES. 1/10W F 24k ΩRRXAFR5H2402
R660WIRE COPPER 6111-06003-0120XZ40C0SHG002
R661RES. CARBON FILM J 1/2W J 390 ΩRCX2391T1003
R662RES CARBON FILM T 1/4W J 15 ΩRCX4150T1001
R663RES CARBON FILM T 1/4W J 1.8k ΩRCX4182T1001
R664RES CARBON FILM T 1/4W J 1.8k ΩRCX4182T1001
R665WIRE COPPER 6111-06003-0120XZ40C0SHG002
R666RES CARBON FILM T 1/4W J 1.0 ΩRCX41R0T1001
R667WIRE COPPER 6111-06003-0120XZ40C0SHG002
R668CHIP RES. 1/10W F 620 ΩRRXAFR5H6200
R669CHIP RES. 1/10W F 1.0k ΩRRXAFR5H1001
R670WIRE COPPER 6111-06003-0120XZ40C0SHG002
R671WIRE COPPER 6111-06003-0120XZ40C0SHG002
R672METAL OXIDE RES. 1W J 0.33 ΩRN01R33ZU001
R673RES CARBON FILM T 1/4W J 22k ΩRCX4223T1001
R674RES CARBON FILM T 1/4W J 1.0k ΩRCX4102T1001
R675CHIP RES. 1/10W J 10k ΩRRXAJR5Z0103
R676CHIP RES. 1/10W J 22k ΩRRXAJR5Z0223
R677RES CARBON FILM T 1/4W J 270 ΩRCX4271T1001
R678RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R679CHIP RES. 1/10W F 3.3k ΩRRXAFR5H3301
R680CHIP RES. 1/10W F 10k ΩRRXAFR5H1002
R682RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
R683RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
R685RES CARBON FILM T 1/4W J 22 ΩRCX4220T1001
R686RES CARBON FILM T 1/4W J 1.0k ΩRCX4102T1001
R687RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R688RES CARBON FILM T 1/4W J 10 ΩRCX4100T1001
R689RES CARBON FILM T 1/4W J 1.2k ΩRCX4122T1001
R691RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
R692RES CARBON FILM T 1/4W J 2.7 ΩRCX42R7T1001
--------------------------------------------------------------------FUNCTION CBA
IR SENSOR CBA
JUNCTION CBA
INVERTER CBA
Ref. No.DescriptionPart No.
INVERTER CBA
Consists of the following:
CAPACITORS
C1000ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C1001CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1002CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1003CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1004CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1005CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1006CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1007CHIP CERAMIC CAP.(1608) B K 0.22µF/16VCHD1CK30B224
C1008CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1009ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1011CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1012POLYESTER FILM CAP. (PB FREE) 0.0039µF/
C1013CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1045METALIZED POLYESTER FILM CAP. 0.47µF/
C1050CERAMIC CAP. B K 0.01µF/1KVCCD3AKP0B103
C1051CERAMIC CAP. B K 0.01µF/1KVCCD3AKP0B103
C1061CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1062CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1063ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1064CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1065CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1066CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1067ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1068CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1072CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1111CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1112CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1113ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1114CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1115CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1116CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1117ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1118CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1122CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1161CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1162CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1163ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1164CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1165CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1166CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1167ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1168CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1172CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1211CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1212CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1213ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1214CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
100V J
50V J
A91F2M1V-001
A91F2M1V-001-IV
---------------------------A91F2M1V-001-FNIRJN
----------
CA2A392DT018
CT1J474DT040
2009101315-23A91FAEL
Page 92
Ref. No.DescriptionPart No.
C1215CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1216CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1217ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1218CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1222CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1261CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1262CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1263ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1264CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1265CAP CERAMIC HV 15pF/6KV/SL/JCCA1500TE009
C1266CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1267ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1268CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1272CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1501CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1503CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1510CERAMIC CAP. 470pF/2KVCA3D471PAN04
C1511CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1530CERAMIC CAP. 470pF/2KVCA3D471PAN04
C1531CHIP CERAMIC CAP. CH J 220pF/50VCHD1JJ3CH221
C1600CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1620CHIP CERAMIC CAP.(1608) B K 1000pF/50VCHD1JK30B102
C1700CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1701CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1750CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1751CHIP CERAMIC CAP.(1608) F Z 0.22µF/50VCHD1JZ30F224
C1800ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C1801ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C1802CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1930CERAMIC CAP. 1000pF/2KVCA3D102PAN04
C1931# POLYESTER FILM CAP. (PB FREE) 0.001µF/
C1932POLYESTER FILM CAP. (PB FREE) 0.027µF/
C1933POLYESTER FILM CAP. (PB FREE) 0.1µF/100V JCA2A104DT018
C1941CERAMIC CAP. B K 0.01µF/1KVCCD3AKP0B103
C1970POLYESTER FILM CAP. (PB FREE) 0.047µF/
C1981CHIP CERAMIC CAP. F Z 0.01µF/50VCHD1JZ30F103
C1982ELECTROLYTIC CAP. 0.47µF/50V MCE1JMASDLR47
C1990CERAMIC CAP. B K 1500pF/1KVCCD3AKP0B152
C1992# ELECTROLYTIC CAP 470µF/100VCE2AMZNDL471
C1993ELECTROLYTIC CAP 220µF/100VCE2AMZNDL221
C1994ELECTROLYTIC CAP 220µF/100VCE2AMZNDL221
CN101242 SERIES CONNECTOR TUC-P08X-B1 WHT STJCTUB08TG002
----------
FUNCTION CBA
Ref. No.DescriptionPart No.
FUNCTION CBA
Consists of the following:
----------
CAPACITOR
C108CAP CERAMIC (AX) 0.1µF/50V/F/ZCA1J104TU062
RESISTORS
R108RES CARBON FILM T 1/4W J 220 ΩRCX4221T1001
R109RES CARBON FILM T 1/4W G 10k ΩRCX4103T1002
R111RES CARBON FILM T 1/4W G 4.7k ΩRCX4472T1002
R112RES CARBON FILM T 1/4W G 2.7k ΩRCX4272T1002
R113RES CARBON FILM T 1/4W G 4.7k ΩRCX4472T1002
R114RES CARBON FILM T 1/4W G 8.2k ΩRCX4822T1002
R115RES CARBON FILM T 1/4W G 18k ΩRCX4183T1002
SWTICHES
SW101BTACT SWITCH SKQSABSST0101AL038
SW103BTACT SWITCH SKQSABSST0101AL038
SW104BTACT SWITCH SKQSABSST0101AL038
SW105BTACT SWITCH SKQSABSST0101AL038
SW106BTACT SWITCH SKQSABSST0101AL038
SW107BTACT SWITCH SKQSABSST0101AL038
IR SENSOR CBA
Ref. No.DescriptionPart No.
IR SENSOR CBA
Consists of the following:
CAPACITORS
C101ELECTROLYTIC CAP. 47µF/16V M H7CE1CMAVSL470
C103CHIP CERAMIC CAP. CH J 330pF/50VCHD1JJ3CH331
C104CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
----------
2009101315-27A91FAEL
Page 96
ELECTRICAL PARTS LIST
[32PFL3514D/F7 (Serial No. : YA1A**********)]
PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
2. Tolerance of Capacitors and Resistors are noted
with the following symbols.
C.....±0.25%D.....±0.5%F.....±1%
G.....±2%J......±5%K.....±10%
M.....±20%N.....±30%Z.....+80/-20%
DIGITAL MAIN CBA UNIT
Ref. No.DescriptionPart No.
DIGITAL MAIN CBA UNITA91F2MMA-004
MPW CBA
Ref. No.DescriptionPart No.
MPW CBA
Consists of the following:
POWER SUPPLY CBA(MPW-1)
JACK CBA(MPW-2)
POWER SUPPLY CBA(MPW-1)
Ref. No.DescriptionPart No.
POWER SUPPLY CBA(MPW-1)
Consists of the following:
CAPACITORS
C201CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C202CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C203CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C204ELECTROLYTIC CAP. 2.2µF/50V MCE1JMASDL2R2
C210ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C216CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C217CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C218CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C219ELECTROLYTIC CAP. 47µF/25V MCE1EMASDL470
C221CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C222ELECTROLYTIC CAP. 470µF/25V MCE1EMASDL471
C223ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C224ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C302CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C303ELECTROLYTIC CAP. 1000µF/6.3V MCE0KMASDL102
C305CHIP CERAMIC CAP.(1608) F Z 0.1µF/50VCHD1JZ30F104
C306ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL1R0
C309CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C310CHIP CERAMIC CAP.(1608) CH J 47pF/50VCHD1JJ3CH470
C311CHIP CERAMIC CAP.(1608) CH J 47pF/50VCHD1JJ3CH470
C402CHIP CERAMIC CAP.(1608) B K 0.033µF/50VCHD1JK30B333
A91F2MPW-001
----------
----------
----------
Ref. No.DescriptionPart No.
C501ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C601#CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004
C602#CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004
C605CAP ELECTROLYTIC 470µF/200V MCA2D471DYG07
C609POLYESTER FILM CAP. (PB FREE) 0.047µF/
C610POLYESTER FILM CAP. (PB FREE) 0.0012µF/
C611CERAMIC CAP. 470pF/2KVCA3D471PAN04
C612POLYESTER FILM CAP. (PB FREE) 0.068µF/
C647ELECTROLYTIC CAP. 1µF/50V MCE1JMASDL1R0
C648ELECTROLYTIC CAP. 100µF/10V MCE1AMASDL101
C652ELECTROLYTIC CAP. 1000µF/6.3V MCE0KMASDL102
C653ELECTROLYTIC CAP. 220µF/10V MCE1AMASDL221
C654ELECTROLYTIC CAP. 220µF/10V MCE1AMASDL221
C656ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C657ELECTROLYTIC CAP. 22µF/50V MCE1JMASDL220
C676ELECTROLYTIC CAP. 2.2µF/50V MCE1JMASDL2R2
C681CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C682CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C683CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C684CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C691#SAFTY CAP. 1000pF/250V KXCA2E102MR101
C693#SAFTY CAP. 1000pF/250V KXCA2E102MR101
C723CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C724CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C731CHIP CERAMIC CAP. CH J 39pF/50VCHD1JJ3CH390
C732CHIP CERAMIC CAP. CH J 39pF/50VCHD1JJ3CH390
C733CHIP CERAMIC CAP. CH J 39pF/50VCHD1JJ3CH390
C734CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
C735CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
C736CHIP RES.(1608) 1/10W 0 ΩRRXAZR5Z0000
C743CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C744CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C771ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C772CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C775CHIP CERAMIC CAP.(1608) CH J 100pF/50VCHD1JJ3CH101
C776CHIP CERAMIC CAP.(1608) CH J 100pF/50VCHD1JJ3CH101
C801CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C802CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C803CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C804CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C805CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C806CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
100V J
100V J
100V J
100V J
100V J
CA2A473DT018
CA2A122DT018
CA2A683DT018
CA2A152DT018
CA2A222DT018
2009100515-28A91FREL
Page 97
Ref. No.DescriptionPart No.
C807CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C808CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C809CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C810CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C811CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C815CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C816ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C817CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C818CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C819ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C820CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C821CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C822CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C823ELECTROLYTIC CAP. 1000µF/25V MCE1EMZNDL102
C824CHIP CERAMIC CAP.(1608) B K 1µF/25VCHD1EK30B105
C825CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C826CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
C827ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C828CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C829CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C830CHIP CERAMIC CAP.(1608) B K 0.47µF/16VCHD1CK30B474
C832ELECTROLYTIC CAP. 3.3µF/50V MCE1JMASDL3R3
C833CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C834CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C835CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C836CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C837CHIP CERAMIC CAP.(1608) B K 2700pF/50VCHD1JK30B272
C838CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C839CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C841CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C842CHIP CERAMIC CAP. F Z 1µF/10VCHD1AZ30F105
C843CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C844ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C845CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C846CHIP CERAMIC CAP.(1608) CH J 470pF/50VCHD1JJ3CH471
C847CHIP CERAMIC CAP.(1608) B K 0.1µF/25VCHD1EK30B104
C871CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C872CHIP CERAMIC CAP.(1608) B K 3300pF/50VCHD1JK30B332
C873CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C874CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C875CHIP CERAMIC CAP.(1608) CH J 270pF/50VCHD1JJ3CH271
C876CHIP CERAMIC CAP.(1608) CH J 270pF/50VCHD1JJ3CH271
C877CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C878CHIP CERAMIC CAP.(1608) B K 6800pF/50VCHD1JK30B682
C879CHIP CERAMIC CAP.(1608) F Z 0.1µF/25VCHD1EZ30F104
C880ELECTROLYTIC CAP. 100µF/16V MCE1CMASDL101
C882CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C883CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C884CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
C885CHIP CERAMIC CAP.(1608) B K 2.2µF/10VCHD1AK30B225
JK751JACK SW DIN PCB L DIN-435C(777D)JYEL040YUQ03
JK752JACK RCA PCB L RCA-101S(1)-03JXRL010YUQ12
JK753JACK RCA PCB L RCA-101S(1)-04JXRL010YUQ13
----------
Ref. No.DescriptionPart No.
JK754JACK SW RCA PCB L RCA-102F(RD)JYRL010YUQ05
INVERTER ASSEMBLY
Ref. No.DescriptionPart No.
INVERTER ASSEMBLY
Consists of the following:
INVERTER CBA
--------------------------------------------------------------------FUNCTION CBA
IR SENSOR CBA
JUNCTION CBA
INVERTER CBA
Ref. No.DescriptionPart No.
INVERTER CBA
Consists of the following:
CAPACITORS
C1000ELECTROLYTIC CAP. 100µF/25V MCE1EMASDL101
C1001CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1002CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1003CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1004CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1005CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1006CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1007CHIP CERAMIC CAP.(1608) B K 0.22µF/16VCHD1CK30B224
C1008CHIP CERAMIC CAP.(1608) B K 0.1µF/50VCHD1JK30B104
C1009ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1011CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1012POLYESTER FILM CAP. (PB FREE) 0.0039µF/
C1013CHIP CERAMIC CAP.(1608) B K 0.1µF/16VCHD1CK30B104
C1045METALIZED POLYESTER FILM CAP. 0.47µF/
C1050CERAMIC CAP. B K 0.01µF/1KVCCD3AKN0B103
C1051CERAMIC CAP. B K 0.01µF/1KVCCD3AKN0B103
C1061CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1062CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1063ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1064CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1065CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1066CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1067ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1068CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1072CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1111CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1112CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1113ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1114CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1115CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1116CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1117ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1118CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1122CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1161CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1162CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1163ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1164CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1165CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
C1166CAP CERAMIC (AX) 1500pF/50V/B/KCA1J152TU061
C1167ELECTROLYTIC CAP. 10µF/50V MCE1JMASDL100
C1168CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1172CHIP CERAMIC CAP.(1608) B K 0.01µF/50VCHD1JK30B103
C1211CAP CERAMIC HV 15pF/6KV/SL/JCCE1500TE009
100V J
50V J
A91FQM1V-001
A91FQM1V-001-IV
---------------------------A91FQM1V-001-FNIRJN
----------
CA2A392DT018
CT1J474DT040
2009100515-32A91FREL
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.