Philips FC8404 Service Manual
City Line Roma Vacuum cleaner
FC8404
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION
- Electronic controled motor rpm
- Cordwinder build-in with flat cord
- Dustbag-full indicator in dustcover
- This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
TECHNICAL INFORMATION
- Maximum air displacement : 34 l/sec
- Maximum vacuum water column : 280 cm
- Power consumptio (IEC) 225V : 1400 W
- Dust storage capacity : 2 litres
- Cord length (depends on version) : 6 m
- Filter system : 6 filters
- Dimensions cleaner : 37 x 28 x 23 cm
- Weight + accessoiries on board : 4.3 kg
- Noise : 80 dB
- Colour : Apricot gold
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- To open the appliance, first remove the screws A,B,C,D.
- To reach the motor remove the screws E.
- To disassemble the cordwider use Torx screw driver no T10,
which is one of set consisting of :
T20, T15, T10, T9, T8, T7 and T6 = 4822 395 50145.
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
- First remove the two screws
B of (item 15) hinge turn +
window. Remove (item 15)
hinge turn + window from (item
3) upper housing by means of a
flat instrument (e.g. screw driver)
as shown (to prevent demage).
The hinge turn + window has
snaps which fits into the upper
housing. Vario / knob turn
(item 10 ) can now be separated
as shown in next drawing.
- Place the knob turn in line with
the adjuster item 10A. Hook
(item 15) hinge turn + window
into the (item 3) upper housing.
Use the 2 screws (item B) to
fasten item 15 to item 3. Place
the cover of vario / knob turn
(item 10) in the correct way;
only on one way possible.
REPAIR INSTRUCTION
- Give attention that the contact fingers (item 45) are placed on
the cord-winder shaft in such a way that the pressure point of the
cordwinder knob to the cord winderlever (item 40) is vertical.
- The spare parts have been standardized as much as possible.
- Component configuration on exploded view may differ in case of
specific versions, however, the actual components are distinguished
by means of code numbers.
- Item 1 Cotton dustbag is used in those countries where paper
dustbags are not available
- Item 41 Cord-winder spring unit is provided with a long spring,
both long and short cords can be used in combination with this
spring.
- Cordwinder spring has to be tensioned till maximum minus
approx. 1,5 revolution.
B
1
B
2
4
B
3
B
2
1
02/12
PARTS LIST & ELECTRICAL DIAGRAM
FC8404
Pos Service code Description
1
2
3
4
5
6
7
8
9
10
10A
11
12
13
14
15
16
17
18
19
20
21
22
22A
23
24
25
26
27
28
4822 480 10113
8836 999 90010
8836 997 01010
4322 009 06030
4322 009 06150
4322 001 73150
4322 003 20580
4322 005 13780
4322 003 17230
4322 009 06050
4322 005 13960
4322 009 06170
4322 003 11730
4322 009 06100
4322 001 72900
4322 001 73160
4322 009 08460
4322 000 35360
4322 009 06190
4322 009 06070
4322 003 20640
8836 932 01210
4322 009 06080
4322 003 20600
4322 000 09750
4322 006 22440
4322 006 50600
4322 001 73270
4322 003 17850
4322 001 72780
4322 009 06430
4322 003 11990
4322 009 07520
S-paper dustbags FC8021
Sydney 3M dustbags (opt.)
Sydney cotton dustbag (opt.)
dustbag holder
upperhousing (canyon grey)
inletrubber
nose piece (canyon grey)
caster dish assy
fi xing pin
lower housing (canyon grey)
handle turn (apricot gold)
vario / knob turn
adjuster
dust cover assy (apricot gold)
motor buffer
m.c. sealing
safety fi lter and holder
safety fi lter (duo)
hinge turn + window (canyon grey)
cord outlet (canyon grey)
back grille (canyon grey)
exhaust fi lter
rear wheel (canyon grey)
knobs (canyon grey)
pedal spring
PCB ans 220 - 240 V turn
Switch (soldered version)
AP cooling connection
motor cap
buffer ring front
motor ans 220 - 240 V
receptical housing (opt.)
motor foam / disc / ans
Pos Service code Description
40
41
42
43
44
45
46
47
48
49
50
51
55
56
57
58
59
60
61
62
63
64
4322 003 06620
4322 009 07610
4322 001 72360
4322 009 07640
4322 009 07620
4322 009 07630
4322 006 02110
4322 006 01380
4322 006 01770
4322 006 02100
4322 006 02060
4322 006 02080
4322 006 02070
4341 004 20170
4341 004 20100
4341 004 20190
4322 004 21810
4341 003 00240
4322 002 22610
4322 003 10020
4322 004 21050
4341 004 20450
4322 003 17380
push rod
reelhalf springside
brake tyre
base plate
reelhalf contactside
contact plate
Argentina L = 6.3 m
Australia L = 6.3 m
Japan / Taiwan L = 5.3 m
H.K. / U.K. L = 6.3 m
Euro 4.8 mm L = 6.3 m
Swiss L = 6.3 m
Italy L = 6.3 m
crevice nozzle
small nozzle
plumeau
big nozzle RD262 con. (standard)
tube clip (opt.)
metal tube (opt.)
clip telesc. tube
telescopic tube
bend + hose ass’y
bend (standard)
= changed
OPTIONAL (accessories)
Exhaust air filter HR6932 (8836 932 01210)
Sydney cotton dustbag HR6997 (8836 997 01010)
Sydney 3M dustbag HR6999 (8836 999 90010)
S-paper dustbags FC8021 (4822 480 10113)
Turbo brush con. HR6988 (4822 479 20196)
Polishing nozzle con. HR8040 (4322 004 22330)
M
SPEED
CONTROL UNIT
C
CORD WINDER
2-5
Loading...