Philips DVP620VR 78 Owner Manual
DVP620VRDigital Video Disc Player &
Video Cassette Recorder
Owner’s Manual
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 1
2
Safety and General Information
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose this equipment to rain or
moisture.
Federal Communications Commission (FCC) Warning: Any unauthorized changes or
modifications to this equipment void the user’s authority to operate it.
Department of Health and Human Services (DHHS) Certification: Complies with
2
1 Center for Radiation (CFR) chapter 1 subchapter J applicable at time of manufacture.
Laser Safety: This unit employs a laser. Only a qualified service person should remove
the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION:VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.THE BEAM IS LOCATED INSIDE, NEAR THE
DECK MECHANISM.
Special Information for Canadian Users: This Class B digital apparatus
complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Radio/TV Interference: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.These limits
are designed to provide reasonable protection against harmful interference in a residential
installation.This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1)Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and the receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
Copyright Protection: Unauthorized copying, broadcasting, public performance, and
lending of Discs are prohibited.This product incorporates copyright protection technology
that is protected by method claims of certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other rights owners.Use of this copyright
protection technology must be authorized by Macrovision Corporation and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Notice for Progressive Scan Use: Consumers should note that not all high
definition television sets are fully compatible with this product and may cause artifacts to be
displayed in the picture. In case of 525 progressive scan picture problems, it is recommended
that the user switch the connection to the ‘standard definition’ output. If there are questions
regarding your TV set compatibility with this model 525p DVD player, please contact our
customer service center.
Note to the Cable TV System Installer: This reminder is provided to call
the Cable TV system installer’s attention to Article 820-40 of the National Electrical Code,
which provides guidelines for proper grounding – in particular, specifying that the cable
ground shall be connected to the grounding system of the building, as close to the point of
cable entry as possible.
Declaration of Conformity
Model Number: DVP620VR
Trade Name: Philips
Responsible Party: Philips Consumer Electronics
Manufactured under license from Dolby Laboratories."Dolby" and the double-D symbol are trademarks of
Dolby Laboratories.
Copyright 2004 Philips.All rights reserved.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 2
Table of Contents
3
General Information
Safety and General Information . . . . . . . . . . . . . . . . .2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Playable Discs and Video Cassettes . . . . . . . . . . . . . .5
Initial DVD/VCR Setup
Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14
Remote Control Setup . . . . . . . . . . . . . . . . . . . . . .15
First-time DVD/VCR Setup . . . . . . . . . . . . . . . . . . .16
Basic Playback
Video Cassette Playback . . . . . . . . . . . . . . . . . . . . .17
Disc Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Basic DVD/VCR Controls
Display Panel (DVD) . . . . . . . . . . . . . . . . . . . . . . . .19
Display Panel (VCR) . . . . . . . . . . . . . . . . . . . . . . . .20
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Remote Control . . . . . . . . . . . . . . . . . . . . . . . .23-24
Additional VCR Setup
Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . .25-26
Clock (VCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . .27-28
Language (VCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
VCR Status Displays . . . . . . . . . . . . . . . . . . . . . . . .30
VCR Recording Options
Videotape Recording . . . . . . . . . . . . . . . . . . . . . . . .31
Recording One Channel/Watching Another . . . . . .32
One-Touch Recording . . . . . . . . . . . . . . . . . . . . . . .33
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . .34
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . .35-37
DVD to Videotape Duplication . . . . . . . . . . . . . . . .38
Video Cassette Playing Options
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Ta pe Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Time Search, Index Search . . . . . . . . . . . . . . . . . . . .41
Special Effects Playback . . . . . . . . . . . . . . . . . . . . . .42
Automatic Operation Features . . . . . . . . . . . . . . . .43
Additional VCR Features
Multi-Channel Television Sound . . . . . . . . . . . . .44-45
Hi-Fi Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Disc Playback Features
DVD Disc Menus . . . . . . . . . . . . . . . . . . . . . . . . . .47
Fast Forward/Reverse Search . . . . . . . . . . . . . . . . .48
Title/Chapter Playback, Specific Time Playback . . . .49
Track Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Paused and Step-by-Step Playback, Resume On . . .51
Repeat,A-B Repeat . . . . . . . . . . . . . . . . . . . . . . . . .52
Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Subtitles, Camera Angles . . . . . . . . . . . . . . . . . . . . .54
Parental Controls Password . . . . . . . . . . . . . . . . . .55
Parental Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Audio Language, Stereo Sound Mode . . . . . . . . . . .57
Slow Motion, Zoom . . . . . . . . . . . . . . . . . . . . . . . .58
Programmed Playback . . . . . . . . . . . . . . . . . . . . . . .59
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . .60
MP3/JPEG Playback . . . . . . . . . . . . . . . . . . . . . . . . .61
MP3/JPEG Displays . . . . . . . . . . . . . . . . . . . . . . . . .62
DVD Player Setup Options
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63-64
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65-66
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . .68
Black Level,Virtual Surround . . . . . . . . . . . . . . . . . .69
Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Information You May Need
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . .73-76
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . .77
Information Index . . . . . . . . . . . . . . . . . . . . . . . . . .78
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 3
4
Introduction
VCR Features
• Automatic Head Cleaner
• Channel Setup
• English, French, and Spanish menus and
displays
• Multi-Channel TV Sound
• 19 Micron head
• Recording: One-Touch and Timer
• Repeat Play
• Searching:Time, Index, Forward,and
Reverse
• Slow Motion
• Still Picture
•Tape Counter
•Tracking Adjustment
Welcome!
This DVD/VCR combines a Digital Video Disc (DVD) Player and a Hi-Fi Video Cassette
Recorder (VCR) into one unit, letting you play DVDs,Audio Compact Discs (Audio
CDs), and Video Cassettes on one piece of equipment.
Read this owner’s manual carefully to learn how to use the features listed below.
Package Contents
The following items are provided with your new DVD/VCR.
• Remote Control and two AA batteries
• One black RF coaxial cable, 75 ohm
• One set of Audio (red and white tips) and Video (yellow tips) cables
• This Owner’s Manual and Quick-Use Guide
DVD Disc Menus...
Some explanations in this manual describe DVD Disc menus. DVD manufacturers set
the menus, which vary among DVDs. Not all DVDs have menus. If the DVD has a
menu, access it by pressing DVD, then DISC/VCR/MENU on the remote control.
Details are on page 47.
DVD Player Setup Menu...
Some instructions explain how to use the DVD Player’s Setup menu to set up features
of the DVD Player or a DVD.Access the DVD Player menu by pressing
SYSTEM/MENU on the remote control when playback is stopped. Even if a feature is
set in the DVD Player’s menu, it may not be available if the current DVD does not
include that feature.
Available Disc Features...
All features described in this manual are not available on every Disc. If
the feature is not available on the Disc, you cannot use the DVD/VCR
to make it available.An “X” will appear in the top right corner of the
TV screen if you try to access a feature that is not currently available.
Disc Features
• Audio Language choices*
•Bit Rate display
• Camera Angle*
• Dolby Digital Sound*
•DVD to Videotape Duplication
• Dynamic Range Control
• Fast/Paused/Slow/Step-by-Step Playback
• Markers
• Parental Controls*
•Program Playback
• Progressive Scan
• Random Playback
• Repeat, Repeat A-B
• Screen Saver
• Search (Title/Chapter,Time,Track)
• Subtitles*
• Virtual Surround
•Zoom
* If available on the DVD
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 4
Playable Discs and Video Cassettes
5
Region Codes
This DVD/VCR has a Region One (1) DVD Player. DVDs must be labeled for ALL
regions or for Region 1 in order to play on the DVD Player.You cannot play DVDs
that are labeled for other regions. Look for the symbols below on your DVDs. If these
region symbols do not appear on your DVD, you cannot play the DVD in this DVD
Player.
The number inside the globe refers to a region of the world. Region 4 represents
Australia, New Zealand, Pacific Islands, Central America, Mexico, South America, and
the Caribbean.
A DVD labelled for a specific region can only play on DVD Players with the same
region code.
Color Systems
DVDs are recorded in different color systems throughout the world.The most
common color systems are NTSC (which is used primarily in the United States and
North America), PAL, and SECAM.
This DVD Player will play both NTSC and PAL DVDs.You cannot play DVDs recorded
in other formats.The color system of the DVD may be listed on the DVD or on the
Disc case.Your TV must have the NTSC and/or PAL color system as well.
Playable Video Cassettes
The VCR of this DVD/VCR has a High Quality (HQ) system and is compatible with
existing Video Home System (VHS) equipment. Use only video cassettes that have the
mark.The use of other tapes may result in poor picture quality and excessive
deposits on the video heads, which may not be covered by the warranty if damage
occurs.
The VCR also has a 19 micron head, which provides a better picture when you view
tapes recorded in slow speed (SLP).
Playable Discs
The DVD Player will play Digital Video Discs (DVDs);Audio Compact Discs (CDs);
finalized Digital Video Discs Rewritable (DVD+RW); finalized Compact Discs Rewritable
(CD-RW) and Compact Discs Recordable (CD-R); and Video Compact Discs (VCDs).
To play a DVD, make sure it meets the requirements for Region Codes and Color
Systems as described below. Discs that have the following logos will play on the DVD
Player. Other Disc types are not guaranteed to play in the DVD/VCR.
On a Super Audio CD, only the sound on the normal CD layer can be heard.The
sound on the high-density Super Audio CD layer cannot be heard.
DVD Audio CD CD-RW/CD-R Video CD DVD+RW
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 5
Recordable
ReWritable
4
6
Hookups
Determining the best possible connection...
Your hookup will be determined primarily by your existing equipment, especially your TV. However, the following
guidelines describe which options have the best picture (video) and sound (audio) quality.You will not use all the jacks on
the DVD/VCR.
If your TV only has an RF-style jack, usually labelled Antenna In,RF In, or 75 ohm, use the ANT-OUT jack
of the DVD/VCR to connect to the TV.This hookup provides both audio and video in a single cable. Set
your TV to channel 3 or 4 - the output channel of the DVD/VCR.This connection allows you to use both
the DVD and VCR features.
Details are on page 7.
★★★★ If your TV has Component Video In jacks (which could be labelled Y CR CB,Y PR PB, or YUV and may be
green, blue, and red),use the Component Video jacks (Y C
B/PB CR/PR) for the best picture quality. If you
use only this video connection, only the DVD picture will be available.To see DVD features on the TV,
set the TV to its Component Video In channel. Component Video provides the best picture quality.
Details are on page 11.
Progressive Scan provides less flickering and higher image resolution than traditional (525I/480i or interlace)
TV signals. If your TV has Progressive Scan (525P/480p or progressive), connect the TV to the DVD/VCR’s
COMPONENT VIDEO OUT (Y CR/PRCB/PB) jacks.
Set PROGRESSIVE to ON in the DVD/VCR’s DISPLAY menu. Details are on pages 63-64.“P.SCAN” will
appear on the DVD/VCR’s display panel. Set your TV to Progressive Scan also.
If your TV does not have Progressive Scan but has Component Video In jacks, connect them to the
DVD/VCR’s COMPONENT VIDEO OUT jacks (Y CR/PRCB/PB). Set PROGRESSIVE to OFF by pressing and
holding the PLAY button on the front of the DVD/VCR for more than five seconds.
Details are on pages 63-
64.
★★★ If your TV has an S-Video In jack (which also may be labelled Y/C or S-VHS), use the S-VIDEO OUT
jack for excellent picture quality. If you use only this video connection, only the DVD picture will be
available.To see DVD features on the TV, set the TV to its S-Video In channel.Details are on page 12.
★★ If your TV has a single yellow Video In jack (which also may be labelled CVBS, Composite, or baseband),
use the yellow DVD/VCR VIDEO OUT jack for good picture quality.This connection provides a picture
for both the DVD Player and the VCR.To see DVD or VCR features on the TV, set the TV to its Video
In channel. Details are on page 10.
★★★★ If you have a Stereo with a Coaxial Digital Audio In jack, this provides the clearest sound for the DVD
Player. Connect the DVD/VCR’s COAXIAL DIGITAL AUDIO OUT jack to your Stereo for the best
sound quality. If you use only this audio connection, only Disc sound (no VCR) will be available.
Details
are on page 14.
★★★ If digital audio connections are not possible, connect the DVD/VCR’s red and white DVD/VCR AUDIO
OUT jacks to the Audio In jacks of your Stereo or TV.This connection provides sound for both the
DVD Player and the VCR.
Details are on pages 10-13.
Before you begin...
● Refer to the manuals of your TV, Cable Box, Stereo, or other devices as necessary. Note the style of jacks and
connectors on the other equipment. Determine how to choose different Audio and Video In channels on your other
equipment so you can see and hear the DVD/VCR material playing on the TV, Stereo, etc.
● Disconnect all equipment from the power outlets.Connect the equipment to the power outlets only after you have
finished hooking up everything. Never make or change connections with equipment connected to the power outlet.
Remember...
● Set the TV to the correct Video In channel. Such channels may be called AUX or AUXILIARYIN,AUDIO/VIDEO or
A/V IN, EXT1 or External In, etc.These channels often are located near channel zero (0). Or,your TV’s remote may
have a button or switch that selects the Video Input channel. See your TV manual for details. If you do not see the
DVD or VCR playback on the TV, go to the lowest TV channel (01 or 02) and change channels downward until you
see the DVD or VCR picture on the TV. Or,if your TV has only a single Antenna In jack and you are using the RF
coaxial cable (as described on page 7), set the TV to channel 3 or 4.
To help you find the right Audio/Video In channel, turn on the DVD/VCR. Press DVD to put the DVD/VCR in DVD
mode.With no Disc in the Player, a large DVD Video logo will appear on the TV screen when you get the TV on the
correct Audio/Video In channel or channel 3 or 4.
● Set the Stereo to the correct channel or “source” mode.
● Depending on your connection, you may need to purchase additional cables or adaptors.If your TV or monitor has
BNC-type connectors, you will need an adaptor.
● If you set Progressive Scan on or off when the power is on, the DVD/VCR will turn off.When you turn on the DVD
Player again,the last selected scanning system will be active.
● To use the VCR features,you must include a connection with the supplied yellow video cable and
red/white audio cables or with the supplied RF coaxial cable.
Once you determine the best option, find your choice on pages 7-
14. Follow the steps for the hookup you
choose.Then, go to page
16 to complete the first-time setup.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 6
75
ANT /
CABLE
ANT - IN
ANT-OUT
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B
/
P
B
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
P
R
Black RF
coaxial cable
(supplied)
Antenna or
Cable TV
signal
Antenna In Jack
(on back of TV)
example only
1
2
Hookups (cont’d)
7
1
Disconnect the antenna or Cable TV signal from your TV and
connect it to the ANT-IN (Antenna In) jack of your DVD/VCR.
2
Connect the supplied black RF coaxial cable to the ANT-OUT
(Antenna Out) jack on the back of the DVD/VCR and to the
ANTENNA IN JACK on the TV. The ANTENNA IN jack on the TV may be
labelled TV IN, RF IN, 75Ω (ohm), or ANT-IN. See your TV owner’s manual for
assistance.
3
Plug in the power cords of the TV and the DVD/VCR.
4
Set your TV to channel 3 or 4. The DVD/VCR’s output channel is 3 when
you purchase it. So, set your TV to channel 3 when the DVD/VCR is new.
If you cannot use channel 3 at your TV, you can change the DVD/VCR’s output
channel to channel 4.To do so, press the VCR button to put the DVD/VCR in
VCR mode.The VCR light will be on the front of the DVD/VCR. Insert a
videotape and press PLAY B to start playback. During playback, press and
hold the (VCR) PLAY B button on the front of the DVD/VCR for
three to five seconds. Each time you do this, the DVD/VCR’s output
channel switches between 3 and 4, and the selected channel number appears
on the display panel. Change your TV to channel 3 or 4 accordingly. (You
cannot change the DVD/VCR’s output channel while adjusting tracking
manually. Press STOP C to stop play and cancel manual tracking, then press
PLAY B to resume playing and change the output channel.)
There is not a channel 3/4 switch on the DVD/VCR (as customary with most
VCRs).
5
You are ready to turn on the DVD/VCR. Go to page 16 before
turning on the DVD/VCR.
DVD/VCR to TV only
Simplest connection using only the supplied black RF coaxial cable
This connection will let you use the features of both the VCR and the DVD Player.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 7
8
Hookups (cont’d)
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B
/
P
B
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
P
R
OUT
IN
75
ANT /
CABLE
TV’s ANTENNA
IN Jack
Cable Box/Satellite Receiver
DVD/VCR
Connections
1
Connect a Cable TV or Satellite signal to the IN
jack on the Cable Box/Satellite Receiver.
2
Use an RF coaxial cable (as the one supplied) to
connect the OUT jack on the Cable Box/Satellite
Receiver to the ANT-IN (Antenna In) jack on the
DVD/VCR.
3
Use a second RF coaxial cable to connect the ANTOUT (Antenna Out) jack on the DVD/VCR to the
TV’s Antenna In jack.
Remember...
There are two ways to connect your Cable Box/Satellite Receiver
to the DVD/VCR.With the connection on this page:
● Select TV channels at the Cable Box/Satellite Receiver, not the
DVD/VCR.To record or view TV channels, follow these steps:
1) Press VCR to put the DVD/VCR in VCR mode.The VCR light
will appear on the front of the DVD/VCR.
2) Press SKIP ∑/CH o or SKIP w/CH p to set the DVD/VCR
to the Cable Box/Satellite Receiver output channel (03 or 04).
3) Set the TV to the DVD/VCR’s output channel (03 or 04).The
DVD/VCR’s output channel is channel 3 when the DVD/VCR is
new.To change it from 3 to 4, press and hold the (VCR) PLAY
B button on the DVD/VCR for 3-5 seconds during tape
playback. For more details, see step 4 on page 7.
4) Select the channel you want to view/record at the Cable
Box/Satellite Receiver.
●
You may not view a channel other than the one you are recording.
●
You can only program a timer recording for one channel at a time.
Set your Cable Box/Satellite Receiver to the channel you want to
record.When you enter the channel you want to record in a
timer recording, select channel 03 or 04 (the Cable Box/Satellite
Receiver output channel). (This is step 8 on page 36.) Leave the
Cable Box/Satellite Receiver on for a timer recording.
1
2
3
Cable
Signal
RF coaxial cable
RF coaxial cable
DVD/VCR to Cable Box or Satellite Receiver and TV
Using only basic RF coaxial cables
This connection will let you use the features of both the VCR and the DVD Player.
• If your Cable Box or Satellite
Receiver has Audio and Video Out
jacks, use audio and video cables
to connect them to the VCR
AUDIO IN and VIDEO IN jacks on
the rear of the DVD/VCR.You will
not need the RF coaxial cable
connection between the Cable
Box/Satellite Receiver and the
DVD/VCR as described at step 2.
Helpful Hint
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 8
Hookups (cont’d)
9
ANT - IN
ANT-OUT
IN
OUT
75
A
NT /
C
ABLE
TV’s ANTENNA
IN Jack
Cable Box/Satellite Receiver
DVD/VCR
Connections
1
Connect a Cable TV or Satellite signal to the
DVD/VCR’s ANT-IN (Antenna In) jack.
2
Use an RF coaxial cable (as the one supplied) to
connect the ANT-OUT (Antenna Out) jack on the
DVD/VCR to the IN jack on the Cable Box/Satellite
Receiver.
3
Use a second RF coaxial cable to connect the OUT
jack on the Cable Box/Satellite Receiver to the
ANTENNA IN jack on the TV.
Remember...
There are two ways to connect your Cable Box/Satellite Receiver to
the DVD/VCR.With the connection on this page:
● You may watch one channel while recording another. Follow these
steps:
1) Put the Cable Box/Satellite Receiver on the same channel as
the DVD/VCR’s output channel (03 or 04).The DVD/VCR’s output
channel is channel 3 when the DVD/VCR is new.To alternate it
between 3 and 4, press and hold the (VCR) PLAY
B button on the
front of the DVD/VCR for 3-5 seconds during tape playback.
For
details, see step 4 on page 7. Set the TV to the Cable Box/Satellite
Receiver output channel (03 or 04).
2) Press VCR to put the DVD/VCR in VCR mode.The VCR light
will appear on the front of the DVD/VCR.
3) Press VCR/TV on the remote to choose VCR position.
4) Press SKIP ∑/CH o or SKIP w/CH p to select the channel
you want to record at the DVD/VCR. Press RECORD
I to start
the recording.
5) Press VCR/TV on the remote once to put the DVD/VCR in TV
position.
6) Select the channel you want to watch at the Cable
Box/Satellite Receiver.
● When you play a tape or Disc, make sure the Cable Box/Satellite
Receiver is set to the DVD/VCR’s output channel (03 or 04).
Set the TV to the Cable Box/Satellite Receiver output channel
(03 or 04).
1
2
3
Cable
Signal
RF coaxial cable
RF coaxial cable
DVD/VCR to Cable Box or Satellite Receiver and TV
Using only basic RF coaxial cables
This connection will let you use the features of both the VCR and the DVD Player.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 9
10
Hookups (cont’d)
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B
/
P
B
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
P
R
AUDIO IN
VIDEO IN
L
R
Antenna or Cable TV
Signal to ANT-IN Jack
Audio Cables
Video Cable
Audio and
Video IN Jacks
on TV
1
3
2
1
Connect the antenna or Cable TV signal to the ANT-IN (Antenna In)
jack of your DVD/VCR.
2
Connect the red and white audio cables (supplied) to the red and
white DVD/VCR AUDIO OUT jacks on the DVD/VCR and to the red
and white AUDIO IN jacks on the TV. Match the cable colors to the jack
colors. If the TV has a single AUDIO IN jack, use the white audio cable to
connect the DVD/VCR’s white DVD/VCR AUDIO OUT (left) jack to the TV’s
AUDIO IN jack.You will not use the red cable. Or, purchase a “splitter” audio
cable to go from the left/right AUDIO OUT jacks of the DVD/VCR to the TV’s
single AUDIO IN jack.
3
Connect the yellow video cable (supplied) to the DVD/VCR VIDEO
OUT jack on the DVD/VCR and to the VIDEO IN jack on the TV.
The VIDEO IN jack on the TV is usually yellow and may be labelled CVBS,
Composite, or Baseband video.
4
Connect the power cords of the TV and the DVD/VCR to a power
outlet.Turn on the TV and set it to the correct Audio/Video In
channel. Go to your lowest TV channel (01 or 02), then change channels
downward until you see VCR or DVD playback on the TV screen.
To help you find the right Audio/Video In channel, turn on the DVD/VCR. Press
DVD to put the DVD/VCR in DVD mode.With no Disc in the Player, a large DVD
Video logo will appear on the TV screen when you get the TV on the correct
Audio/Video In channel.
Make sure PROGRESSIVE is OFF and P.SCAN does not appear on the DVD/VCR’s
display panel. Disable
Progressive Scan by pressing and holding PLAY B (DVD)
on the front of the DVD/VCR for more than five seconds. Details are on pages 6
and 63-64.
5
You are ready to turn on the DVD/VCR. Go to page 16 to complete
the first-time setup.
DVD/VCR to a TV that has Audio and Video In jacks
Using the supplied red, white, and yellow cables
This connection will let you use the features of both the VCR and the DVD Player.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 10
Hookups (cont’d)
11
DVD/VCR to a TV that has Component Video In jacks
AUDIO IN
Y
Cb/Pb
Cr/Pr
COMPONENT
VIDEO IN
L
R
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B
/
P
B
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
P
R
1
Connect the antenna or Cable TV signal to the ANT-IN (Antenna In)
jack of your DVD/VCR.
2
Connect the supplied red and white audio cables to the red and
white DVD/VCR AUDIO OUT jacks on the DVD/VCR and to the red
and white AUDIO IN jacks on the TV. Match the cable colors to the jack
colors.
3
Connect component video cable (not supplied) to the
COMPONENT VIDEO OUT jacks on the DVD/VCR and to the
COMPONENT VIDEO IN jacks on the TV. The Component Video In
jacks on the TV are usually red, blue, and green.
The Component Video connection only supplies video (picture) for the DVD Player of
the DVD/VCR.Therefore, in order to use the VCR features or view TV channels at the
DVD/VCR, you still need to either connect the RF coaxial cable between the ANT-OUT
jack of the DVD/VCR and the TV’s Antenna In jack, or connect the yellow video cable.
To connect the supplied RF coaxial cable, see step 2 on page 7.To connect the
supplied yellow video cable, see step 3 on page
10.
If your TV is compatible with Progressive Scan (525P/480p), turn on Progressive Scan
at the DVD/VCR. Set PROGRESSIVE to ON in the Display menu so “P. SCAN”
appears on the display panel. Details are on pages 63-64.
If your TV is not compatible with Progressive Scan, press and hold PLAY
B
(DVD) on
the front of the DVD/VCR for more than five seconds so “P. SCAN” does not appear
on the display panel.
4
Connect the power cords of the DVD/VCR and TV to a power outlet.
Turn on the TV and set it to the Component Video In channel for
DVD Player features.
If you are using the RF coaxial cable for VCR playback, choose channel 3 or 4
at the TV. If you are using the yellow video cable for VCR playback, choose the
Video In channel at your TV.
Go to your lowest TV channel and change channels down until you see VCR or
DVD playback on the TV screen, or try channel 3 or 4 at the TV.
To help you find the right Audio/Video In channel, turn on the DVD/VCR. Press
DVD to put the DVD/VCR in DVD mode.With no Disc in the Player, a large DVD
Video logo will appear on the TV screen when you get the TV on the correct
Component Video In channel.
5
You are ready to turn on the DVD/VCR. Go to page 16 before
turning on the DVD/VCR.
2
3
Antenna or
Cable TV
Signal
1
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 11
12
Hookups (cont’d)
DVD/VCR to a TV that has an S-Video In jack
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B
/
P
B
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
P
R
AUDIO IN
LEFT
RIGHT
S-VIDEO IN
1
Connect the antenna or Cable TV signal to the ANT-IN (Antenna In)
jack of your DVD/VCR.
2
Connect the supplied red and white audio cables to the red and
white DVD/VCR AUDIO OUT jacks on the DVD/VCR and to the red
and white AUDIO IN jacks on the TV.
Match the cable colors to the jack
colors.
3
Connect an S-Video cable (not supplied) to the S-VIDEO OUT jack
on the DVD/VCR and to the S-VIDEO IN jack on the TV.
The S-Video connection only supplies video (picture) for the DVD Player of the
DVD/VCR.Therefore, in order to use the VCR features or view TV channels at the
DVD/VCR, you still need to either connect the RF coaxial cable between the ANT-OUT
jack of the DVD/VCR and the TV’s Antenna In jack, or connect the yellow video cable.
To connect the supplied RF coaxial cable, see step 2 on page 7.To connect the
supplied yellow video cable, see step 3 on page
10.
4
Connect the power cords of the DVD/VCR and TV to a power outlet.
Turn on the TV and set it to the S-Video In channel for DVD Player
features.
If you are using the RF coaxial cable for VCR playback, choose channel 3 or 4
at the TV. If you are using the yellow video cable for VCR playback, choose the
Video In channel at your TV.To find the correct Video In channel, go to your
lowest TV channel and change channels downward until you see VCR or DVD
playback on the TV screen, or try channel 3 or 4 at the TV.
To help you find the right S-Video In channel, turn on the DVD/VCR. Press DVD to
put the DVD/VCR in DVD mode.With no Disc in the Player, a large DVD Video
logo will appear on the TV screen when you get the TV on the S-Video In channel.
Make sure PROGRESSIVE is OFF and “P.SCAN” does not appear on the DVD/VCR
display panel. Disable
Progressive Scan by pressing and holding PLAY B (DVD)
on the front of the DVD/VCR for more than five seconds SO “P.SCAN” does
not appear on the display panel. Details are on pages 63-64.
5
You are ready to turn on the DVD/VCR. Go to page 16 before
turning on the DVD/VCR.
3
2
Antenna/Cable
TV Signal
1
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 12
Hookups (cont’d)
13
DVD/VCR to a TV and a Stereo
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B
/
P
B
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
P
R
VIDEO IN
AUDIO (LEFT) IN
AUDIO (RIGHT) IN
1
Connect the antenna or Cable TV signal to the ANT-IN (Antenna In)
jack of your DVD/VCR.
2
Connect the supplied red and white audio cables to the red and
white DVD/VCR AUDIO OUT jacks on the DVD/VCR and to the red
and white AUDIO IN jacks on the Stereo. Match the cable colors to the
jack colors.
3
Connect the supplied yellow video cable to the DVD/VCR VIDEO
OUT jack on the DVD/VCR and to the VIDEO IN jack on the TV.
To use Component Video cable or S-Video cable instead for the DVD Player,
see pages 11-12.You will still need the yellow video cable or RF coaxial cable
for VCR features.
4
Connect the power cords of the DVD/VCR,TV, and Stereo to a
power outlet.Turn on the TV and set it to the Video In channel. Or,
simply go to your TV’s lowest channel (02 or 03) and continue changing
channels downward at the TV until you see VCR or DVD playback on the TV
screen.
To help you find the right Video In channel at the TV, turn on the DVD/VCR. Press
DVD to put the DVD/VCR in DVD mode.With no Disc in the Player, a large DVD
Video logo will appear on the TV screen when you get the TV on the correct
Video In channel.
Turn on the Stereo and set it to the correct Auxiliary or Source mode.
Check your Stereo manual for details.
5
You are ready to turn on the DVD/VCR. Go to page 16 before
turning on the DVD/VCR.
3
2
Antenna/Cable
TV Signal
1
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 13
1
Connect the antenna or Cable TV signal to the ANT-IN (Antenna In) jack
of your DVD/VCR.
2
Connect a coaxial digital audio cable (not supplied) to the DVD/VCR’s
COAXIAL DIGITAL AUDIO OUT jack and to the COAXIAL DIGITAL
AUDIO IN jack on the Stereo.
This digital audio connection only provides sound for the DVD Player of the DVD/VCR. So, in
order to use the VCR features or hear TV channels at the DVD/VCR, you still need to either
connect the RF coaxial cable between the ANT-OUT jack of the DVD/VCR and the TV’s Antenna
In jack, or connect the supplied red/white audio cables.To connect the supplied RF coaxial cable,
see step 2 on page 7.To connect the red/white audio cables, see step 2 on page
10.
3
Connect the supplied yellow video cable to the yellow DVD/VCR VIDEO
OUT jack on the DVD/VCR and to the VIDEO IN jack on the TV.
To use
component video cable or S-Video cable instead for the DVD Player, see pages
11-
12.You will still need the yellow video cable or RF coaxial cable for VCR features.
4
Plug in the power cords of the Stereo,TV, and DVD/VCR.Turn on the
Stereo and select its Auxiliary IN channel.Turn on the TV and set it to
the correct Video In channel.
Go to your TV’s lowest channel (01 or 02) and
change channels downward until you see DVD or VCR material on the TV screen.
To help you find the right Video In channel on the TV, turn on the DVD/VCR. Press
DVD to put the DVD/VCR in DVD mode.With no Disc in the Player, a large DVD
Video logo will appear on the TV screen when you get the TV on the correct Video
In channel.
Make sure PROGRESSIVE is OFF and “P.SCAN” does not appear on the
DVD/VCR’s display panel. Disable
Progressive Scan by pressing and holding PLAY
B (DVD) on the front of the DVD/VCR for more than five seconds. Details are
on pages 6 and 63-64.
5
You are ready to turn on the DVD/VCR. Go to page 16 before turning on
the DVD/VCR.
Remember...
Some DVDs are recorded in Dolby Digital 5.1 channel Surround.Select Dolby Digital 5.1
channel Surround Sound in the DVD Disc menu. If Dolby Digital Surround is not recorded
on the Disc, you will not have surround sound available.
If you connect the DVD/VCR to a Dolby Digital Stereo, set DOLBY DIGITAL to ON in the
DVD Player’s Setup menu.
Details are on page 67. If the DVD/VCR is not connected to a
Dolby Digital-compatible Stereo,set DOLBY DIGITAL to OFF. Incorrect settings may cause
noise distortion and damage the speakers.
14
Hookups (cont’d)
DVD/VCR to a TV and to a Stereo that is Dolby Digital-compatible
Using Digital Audio connections
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B
/
P
B
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
P
R
VIDEO IN
COAXIAL
DIGITAL
AUDIO IN
2
3
Back of TV
(example only)
Stereo
Antenna/Cable TV Signal
1
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 14
Remote Control Setup
15
Putting Batteries in the Remote Control
1
Remove the battery compartment lid on the bottom
of the remote control by pressing the tab, then lifting the
lid.
2
Place two AA batteries inside the battery
compartment
with their +and –ends aligned as
indicated.
3
Replace the battery compartment lid.
Using the Remote Control
● Point the remote control at the DVD/VCR’s remote sensor (see
page 21) when using the remote to operate the DVD/VCR. Do
not point the remote at the TV.
● Do not put objects between the remote and the DVD/VCR.
Recycling Guidelines/Battery Safety
● Your new product and its packaging contain materials that can
be recycled and reused. Specialized companies can recycle your
product to increase the amount that needs to be properly
disposed.Your product uses batteries that should not be thrown
away when depleted but should be disposed of as small chemical
waste. Please find out about the local regulations on disposal of
your old product, batteries, and packaging whenever you replace
existing equipment.
● Battery Usage CAUTION - To prevent battery leakage that may
result in bodily injury, property damage, or damage to the unit:
Install ALL batteries correctly, with the + and - markings on the
battery aligned as indicated on the unit;
Do not mix batteries, for example, old with new or carbon with
alkaline; and
Remove batteries when the unit will not be used for a long
time.
1
2
3
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 15
16
First-time DVD/VCR Setup
3
Press o or p to select English, French, or Spanish as
the language for VCR on-screen displays and menus.
Then,
press
B.
4
Press B to begin channel programming. AUTO
SETUP will flash on the TV screen during the channel
search.The DVD/VCR will memorize all available channels.
When channel programming is complete, the lowest
available channel will appear on the TV.
These channels will be available when you want to watch
TV while in VCR mode.To put the DVD/VCR in VCR
mode, press VCR so the VCR light appears. Use the SKIP
∑/CH o and SKIP w/CH p buttons to select memorized
channels.To select non-memorized channels, use the
Number buttons.
• To skip this feature and play a tape
immediately, insert a tape with its
record tab removed.
• To skip step 3, press
DISC/VCR/MENU.VCR menus and
displays will be in English.
• If you try to program channels
when there is no antenna or Cable
TV signal connected to the ANT-IN
jack of the DVD/VCR, programming
will stop.AUTO SET UP will stop
flashing. Connect an antenna or
Cable TV signal to the DVD/VCR’s
ANT-IN jack and press Bagain.
• Repeat this process if the power
fails.
•To stop the Channel Setup while
AUTO SET UP is flashing, press
DISC/VCR/MENU.
Helpful Hints
Before turning on your DVD/VCR, make sure batteries are in the
remote control and the DVD/VCR and TV are connected correctly.
You cannot program channels if you are using a Cable Box or a
Satellite Receiver.
These menus may not appear if you have already turned
on the DVD/VCR.
1
Turn on the TV. Set it to channel 3 or 4 or its
AUDIO/VIDEO IN channel, depending on how you
connected the DVD/VCR to a TV.
2
Press VCR, then press STANDBY-ON yy. The VCR light
will appear on the front of the DVD/VCR.The display shown
below will appear.
These menus may not appear if you have already turned on
the DVD/VCR.You may have turned on the DVD/VCR
before to find the Audio/Video In channel of the TV, for
example. If so, follow the steps on page 25 to set up
channels and page 29 to select a language for the VCR
menus.
1
Turn on the TV.
AUTO SET UP
PUSH
B
2
3-4
LANGUAGE SELECT
BENGLISH [ON]
FRANÇAIS
ESPAÑOL
PUSH
B
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 16
SEARCH MODE
SUBTITLE ZOOM
RETURN TITLE
REPEAT REPEAT
A-B
STANDBY-ON
DISPLAY
AUDIO
SKIP / CH
ANGLE
CLEAR/RESET SLOW
DISC/VCR
MENU MENU
SPEED
1 2 3
5
4
9
8
DVDVCR VCR/TV
SYSTEM
OK
PLAY
PAUSESTOP
MARKER RECORDTIMER SET
7
6
0
+10
Video Cassette Playback
17
• Other tape playback features are
on pages 39-46.
• If AUTO REPEAT is ON, playback will
begin when you insert a tape, even
when the record tab is intact. Details
are on page 39.
• You must connect the DVD/VCR to
a TV using the RF coaxial cable or
the audio/video cables in order to
use the VCR features.These hookups
are explained on pages 7 and 10.
Helpful Hints
Read and follow the steps below to play a tape.
1
Turn on the TV. Set it to channel 3 or 4 or its
AUDIO/VIDEO IN channel. This depends on how you
connected the DVD/VCR to a TV.
Details are on pages 6-14.
2
With the DVD/VCR power off, insert a tape in the
cassette compartment of the DVD/VCR.The VCR
light will appear on the front of the DVD/VCR. If the tape’s
record tab has been removed, play will start automatically.
If the DVD/VCR power is already on, press VCR to put the
DVD/VCR in VCR mode if necessary.The VCR light will
appear on the front of the DVD/VCR.
3
If playback does not start automatically, press VCR,
then press PLAY B.
4
Press STOP C to stop playback.
5
Press h to rewind the tape.
6
After the tape stops, press STOP/EJECT CA on the
front of the DVD/VCR to remove the tape.
1
2
6
Press STOP/EJECT C A
on the DVD/VCR.
Turn on the TV.
Insert a tape in the
DVD/VCR.
3
4
5
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 17
SEARCH MODE
REPEAT REPEAT
SUBTITLE ZOOM
RETURN TITLE
DISC/VCR
MENU MENU
SPEED
4
8
STANDBY-ON
DISPLAY
AUDIO
A-B
ANGLE
CLEAR/RESET SLOW
OK
PLAY
MARKER RECORDTIMER SET
1 2 3
5
6
0
9
SKIP / CH
DVDVCR VCR/TV
SYSTEM
PAUSESTOP
7
+10
18
Disc Playback
• An “X” may appear at the top right
corner of the TV screen when you
try a feature. Either the feature is
not available on the Disc, or the
DVD/VCR cannot access the feature
at this time.This does not indicate a
problem with the DVD/VCR.
• If a Disc is dirty or scratched, the
picture may appear distorted or
playback may stop. Remove the Disc
and turn off the DVD/VCR.
Disconnect the power cord, then
reconnect it. Clean the Disc, then
turn on the DVD/VCR again and
reinsert the Disc for playback.
• When the DVD or CD light appears
on the display panel, the Disc is
loaded and ready for playback.
• When you press OPEN/CLOSE
A
or
PLAY (DVD) on the front of the
DVD/VCR when the power is off,the
DVD/VCR will turn on in DVD mode.
Otherwise, the DVD/VCR will turn on
in the mode in which it was turned
off.
Helpful Hints
Before you begin, turn on the TV, Stereo, and other equipment
connected to the DVD/VCR. Make sure the TV and the Stereo (if
applicable) are set to the correct channel.
Details are on pages 6-14.
1
Press STANDBY-ON yyto turn on the DVD/VCR.
2
Press DVD so the DVD light appears on the front of
the DVD/VCR.
3
Press OPEN/CLOSE A (to the left of the disc tray on
the front of the DVD/VCR) to open the Disc tray.
4
Place a Disc into the tray. If the DVD is recorded on
only one side, place the Disc in the tray with the label
facing up and the shiny side facing down. Some DVDs are
recorded on both sides. Make sure the label of the side you
want to play is facing up.
5
Press PLAY B. The tray will close and play will begin at
the first Chapter or Track. If a DVD menu appears instead,
see page 47. With some Audio CDs, playback will not begin
unless you press PLAY B.
Or, press OPEN/CLOSE A or press the tray toward the
DVD/VCR to close the tray.
With MP3 and JPEG files, playback will begin from the
beginning of the disc.
6
Press STOP C to stop playback.
Insert a Disc.
4
Remember, this DVD/VCR
will play only certain Discs.
See page 5 for details.
Press OPEN/CLOSE A
on the DVD/VCR.
3
1
2
6
5
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 18
STANDBY-ON
SEARCH MODE
REPEAT REPEAT
SUBTITLE ZOOM
RETURN TITLE
DISC/VCR
MENU MENU
DISPLAY
AUDIO
A-B
ANGLE
CLEAR/RESET SLOW
OK
PLAY
MARKER RECORDTIMER SET
SKIP / CH
DVDVCR VCR/TV
SYSTEM
PAUSESTOP
Display Panel (DVD)
19
Display
Messages about current Disc
operations appear here.
See Display Messages below.
STANDBY-ON
SOURCE
POWER ON
VIDEO AUDIO REW F.FWD PLAY
RECORD CHANNEL
VCR
OPEN/CLOSE
DVD
STOP PLAY
ONE TOUCH RECORDING • LONG PLAY
STOP/EJECT
LR
GROUP P.SCAN
DVD
VCD
DVD light
This light appears when the DVD/VCR is in
DVD mode.You can only watch DVDs when
the DVD light is on.To make the DVD light
come on, press SOURCE on the front of the
DVD/VCR or DVD on the remote.
Disc tray
Insert a Disc here.
Appears after the disc tray closes if the tray is empty, if
there is an error reading the disc, or if an unacceptable
disc is installed.
Tr ay is opening or is open.
Tr ay is closing.
Disc is loading.
Appears when Playback Control is active (Video CD).
Display Messages
Appears when a repeat
function is active
Appears when A-B
Repeat is on
Appears during Disc play
Appears during slow
motion play (DVD,
Video CD)
Appears when
Progressive Scan is
active
Displays the current Disc type
• DVD: DVD
• CD:Audio CD, MP3, JPEG
• VCD:Video CD
Displays the elapsed playing time of
the current Title or Track; briefly
displays a Track, Chapter, or Title
number when play begins.
Appears when ALL
Repeat is on
Appears when Disc
play is paused
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 19
STANDBY-ON
SOURCE
POWER ON
VIDEO AUDIO REW F.FWD PLAY
RECORD CHANNEL
VCR
OPEN/CLOSE
DVD
STOP PLAY
ONE TOUCH RECORDING • LONG PLAY
STOP/EJECT
LR
VCR REC
PM
20
Display Panel (VCR)
Cassette Compartment
Insert a video cassette here.
VCR light
This light appears when the DVD/VCR is
in VCR mode.You can only watch
videotapes or access VCR features and TV
channels when the VCR light is on.
To make the VCR light come on, press
VCR on the remote control or SOURCE
on the front of the DVD/VCR.
Indicates a tape
is in the
DVD/VCR.
Indicates VCR position
Appears if
Repeat Play
is active
Appears if tape
play is paused or
during slow
motion tape play
Appears during
tape play
Appears when a timer
recording or an OTR
has been set
Appears during
recording; flashes when
recording is paused
Indicates current time is P.M.
There is no A.M. indication.
Indicates the elapsed playing time of a
tape; also displays a channel number,
tape speed, remaining time for an
OTR, or the current time
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 20
Front Panel
21
STANDBY-ON
SOURCE
POWER ON
VIDEO AUDIO REW F.FWD PLAY
RECORD CHANNEL
VCR
OPEN/CLOSE
DVD
STOP PLAY
ONE TOUCH RECORDING • LONG PLAY
STOP/EJECT
LR
OPEN/CLOSE A Button (DVD)
Press to open or close the Disc tray.
CHANNEL op Buttons
Press to select TV channels
at the VCR.
PLAY B Button (VCR)
Press to play a video cassette.
Press to release Slow, Search, or
Still mode and return to playback.
Details are on page 42.
STOP/EJECT C A
Button (VCR)
Press once to stop tape
playback.When play is stopped,
press to eject the tape.
RECORD I button (VCR)
Press once to start a recording.
Press repeatedly to start a One-Touch
Recording. Details are on page 33.
Remote Sensor
Receives a signal from your remote control so
you can work your DVD/VCR from a distance.
Point the remote here, not at your TV.
STANDBY-ON yyButton
Press to turn the power on
or off.
POWER ON Light
Appears when the DVD/VCR
power is on
AUDIO and VIDEO In Jacks
Connect audio and video cables
from a camcorder,VCR, etc. here.
This will be useful if you want to
copy a videotape or watch material
that is playing on other equipment.
Details are on page 34.
STOP C Button (DVD)
Press to stop Disc playback.
Details are on page 18.
PLAY B Button (DVD)
Press to start Disc playback.
Details are on page 18.
Press and hold for more
than five seconds to disable
Progressive Scan.
Details are on page 6.
SOURCE Button
Press to select DVD mode or VCR
mode.The DVD light appears in DVD
mode.The VCR light appears in VCR
mode.
REW h
Button (VCR)
Press to rewind
the tape. Details
are on page 42.
F. FWD g
Button (VCR)
Press to fast forward
the tape. Details are
on page 42.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 21
22
Rear Panel
DVD COMPONENT VIDEO OUT
(Y CB/PB CR/PR) Jacks (green, blue, red)
Connect component video cables (not supplied)
here and to the Component Video In jacks of a
TV.This supplies the picture only for the DVD
Player. Details are on page 11.
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
L
R
LRL
R
S-VIDEO
OUT
COMPONENT
VIDEO OUT
Y
C
B /
PB
AUDIO OUT
DVD/VCR
VCR
ANT - IN
ANT-OUT
VIDEO OUT
AUDIO IN
VIDEO IN
CR /
PR
AC Power Cord
Connect to a standard
AC outlet to supply
power to the DVD/VCR.
DVD S-VIDEO OUT Jack
Connect an S-Video cable (not supplied)
here and to the S-Video In jack of a TV.
This supplies the picture only for the
DVD Player. Details are on page 12.
DVD/VCR VIDEO
OUT Jack (yellow)
Connect the yellow video cable
(supplied) here and to the TV’s
Video In jack.This supplies the
picture for both the VCR and the
DVD Player. Details are on page 10.
DVD AUDIO OUT jacks
Left (white) and Right (red)
Connect the supplied audio
cables here and to the Audio In
jacks of a TV or Stereo.These
jacks only supply audio for the
DVD Player. Use these for a
second connection to a TV, etc.
DVD COAXIAL DIGITAL
AUDIO OUT Jack (black)
Connect a coaxial digital audio cable
(not supplied) here and to the Coaxial
Digital Audio In jack of a Stereo.This
supplies audio only for the DVD
Player. Details are on page 14.
ANT-IN
(Antenna In) jack
Connect your antenna
or Cable TV signal here.
Details are on pages 7-14.
ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to
connect this jack to the ANTENNA IN
jack on your TV, Cable Box, or Satellite
Receiver. Details are on pages 7-9.
VCR VIDEO IN Jack (yellow)
Connect a video cable from a
camcorder,VCR, or DVD Player
here. Details are on page 34.
VCR AUDIO IN jacks
Left (white) and Right (red)
Connect audio cables coming
from the audio out jacks of a
camcorder, another VCR,
another DVD Player, or Stereo
here. Details are on page 34. This
will be useful if you want to
copy a videotape or watch
material that is playing on other
equipment.
• The DVD S-VIDEO OUT, DVD
COMPONENT VIDEO OUT, DVD
AUDIO OUT and DVD COAXIAL
DIGITAL AUDIO OUT jacks are only
useful in DVD mode.To have sound
and picture in VCR mode, you must
connect either the RF coaxial cable
or the audio/video cables supplied.
Details are on page 7 and 10.
Helpful Hint
DVD/VCR AUDIO OUT Jacks
Left (white) and Right (red)
Connect the supplied audio cables here and to
the Audio In jacks of a TV or Stereo. Details
are on pages 10-13. These jacks provide audio
for both the DVD Player and the VCR.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 22
Remote Control
23
• For DVD Player features, press DVD before pressing other buttons.To
put the DVD/VCR in DVD mode, press DVD or SOURCE so the DVD
light appears on the front of the DVD/VCR.
• For VCR features, press VCR before pressing any other buttons.To put
the DVD/VCR in VCR mode, press VCR or SOURCE so the VCR light
appears on the front of the DVD/VCR.
Helpful Hints
STANDBY-ON
PLAY
DVD
VCR VCR/TV
OK
MENU MENU
DISC/VCR
RETURN TITLE
A-B
CLEAR/RESET SLOW
SUBTITLE ZOOM
ANGLE
REPEAT REPEAT
AUDIO
SEARCH MODE
DISPLAY
SKIP / CH
SYSTEM
PAUSESTOP
MARKER RECORDTIMER SET
SPEED
1 2 3
7
6
5
4
8
9
0
+10
STANDBY-ON yyButton
Press to turn the power on or off.
sB KLButtons
Press to select an item in a
menu.
g (Fast Forward) Button
In DVD mode, press to fast forward
the Disc. Details are on page 48. Press
when DVD or Video CD playback is
paused to start slow motion playback.
Details are on page 58.
In VCR mode, press to fast forward
the tape. Details are on page 42.
DISPLAY Button
In VCR mode, press to see
status displays. Details are on
page 30. In DVD mode, press
to access Disc information.
Details are on page 68.
REPEAT Button
Press to play a Track, Audio CD,
Title, or Chapter repeatedly.
Details are on page 52.
A-B REPEAT Button
Press to set up A-B Repeat.
Details are on page 52.
RETURN Button
Press to return to the
previous level of the DVD
Player’s Setup menu or to
remove the Setup menu.
SKIP ∑∑/CH ooand SKIP ww/
CH ppButtons
In DVD mode, press to skip
Chapters or Tracks. In VCR
mode, press to change TV
channels at the DVD/VCR.
Press to adjust tracking.
Details are on page 43.
RECORD I Button
Press to start a VCR
recording. Details are on page
31.Press repeatedly to start a
One-Touch Recording.
Details are on page 33.
SEARCH Button
In DVD mode, press to search
for a specific
Title/Chapter/Track/Time. Details
are on pages 49-50.
In VCR mode, press for a Time
Search or an Index Search.
Details are on page 41.
SLOW Button
Press to view a videotape in slow
motion. Details are on page 42.
CLEAR/RESET Button
Press to remove VCR menus.
Press to reset the tape counter.
Details are on page 40.
Press to reset a menu item in
DVD mode.
PAUSE k Button
Press to pause Disc playback.
Press repeatedly to advance
the DVD or Video CD picture
step by step (or one frame at
a time). Details are on page 51.
Press to pause or resume VCR
recording. Details are on page
31. Press to pause a tape.
Details are on page 42.
STOP C Button
Press to stop Disc playback,
tape playback, or recording.
MARKER Button
Press to see the Markers, which give
you quick access to points you
select on a Disc.
Details are on page 53.
TITLE Button
Press to see a DVD Title
menu. Details are on page 47.
PLAY B Button
Press to begin Disc or tape
playback.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 23
24
Remote Control (cont’d)
TIMER SET Button
Press to set a timer recording
that you have programmed.
Details are on pages 35-37.
SUBTITLE Button
Press to select a language for
DVD subtitles. Details are on
page 54.
VCR Button
Press before using the remote
control for VCR features.
Press to put the DVD/VCR in
VCR mode.
OK Button
Press to confirm or select
menu items.
ANGLE Button
Press to see a DVD picture
from a different angle. Details
are on page 54.
Number Buttons
In DVD mode, press to select a Track
or Chapter for playback. Use the +10
button for items 10 and above.
Details are on page 50.
In VCR mode, use to select TV
channels. Enter channel numbers as a
two-digit number for the quickest
results (to select channel 6, press 0,6).
For channels 100 and above, enter a
three-digit number (for channel 117,
press 1, 1, 7). If you have Cable TV,
channels 1-125 are available. If you
have an antenna, channels 2-69 are
available.The +10 button has no effect
in VCR mode.
ZOOM Button
Press to enlarge the DVD,
Video CD, or JPEG image.
Details are on page 58.
STANDBY-ON
PLAY
DVD
VCR VCR/TV
OK
MENU MENU
DISC/VCR
RETURN TITLE
A-B
CLEAR/RESET SLOW
SUBTITLE ZOOM
ANGLE
REPEAT REPEAT
AUDIO
SEARCH MODE
DISPLAY
SKIP / CH
SYSTEM
PAUSESTOP
MARKER RECORDTIMER SET
SPEED
1 2 3
7
6
5
4
8
9
0
+10
MODE Button
Press to set a Program. Details
are on page 59. Press to start
Random playback.
Details are on page 60.
SYSTEM/MENU Button
Press to access or remove the
DVD Player’s Setup menu.
VCR/TV Button
Press to select VCR or TV
position. In VCR position, watch
a tape or watch/record TV
programs (changing channels at
the VCR).
Use TV position to watch TV
channels (changing channels at
the TV) or watch one program
while recording another.
Details are on page 32.
h (Rewind) Button
Press to fast reverse a Disc.
Details are on page 48. Press
when DVD playback is paused
to start reverse slow motion
playback.
Details are on page
58.
Press to rewind a tape. Details
are on page 42.
AUDIO Button
Press to choose a DVD audio
language or an Audio CD
sound mode.
Details are on page 57.
DISC/VCR/MENU Button
Press to access or remove a
DVD Disc menu or the VCR
menu.
DVD Button
Press before using the remote
control for DVD features.
Press to put the DVD/VCR in
DVD mode.
SPEED Button
Press to select the VCR’s
recording speed (SP or SLP).
Details are on pages 31, 34, and 71.
H9622MD(EN)1_46.qx4 04.4.8 5:03 PM Page 24
Loading...