Philips DVP3360K 51 User Manual
Register your product and get support at
www.philips.com/welcome
DVP3360K
DVP3362K
EN User manual
2
Contents
6 Advanced features 25
Create MP3 les 25
English
1 Important 4
Safety and important notice 4
Trademark Notice 5
2 Your DVD player 6
Features highlight 6
Product overview 7
3 Connect 9
Connect video cables 9
Connect audio cables 10
Route audio to other devices 11
Connect USB device 11
Connect to power outlet 11
7 Adjust sound 26
Karaoke settings 26
Turn off vocal (cancel voice) 26
Contents
8 Adjust settings 27
General setup 27
Audio setup 28
Video setup 30
Preferences 33
9 Additional information 35
Update software 35
Care 35
10 Speci cation 36
4 Get started 12
Prepare the remote control 12
Find the correct viewing channel 13
Select menu display language 13
Turn on Progressive Scan 14
Use Philips EasyLink 15
5 Play 16
Play from disc 16
Play video 17
Play music 21
Play photo 22
Play from USB device 24
11 Troubleshooting 37
12 Glossary 39
13 Lifetime card 41
EN 3
1 Important
Safety and important notice
Warning
•
Risk of overheating! Never install the DVD player
in a con ned space. Always leave a space of at least
four inches around the DVD player for ventilation.
Ensure the curtains or other objects never cover the
ventilation slots on the DVD player.
•
Never place the DVD player, remote control or
batteries near naked ames or other heat sources,
including direct sunlight.
•
Only use this DVD player indoors. Keep this DVD
player away from water, moisture and liquid- lled
objects.
Never place this DVD player on other electrical
•
equipment.
Keep away from this DVD player during lightning
•
storms.
Where the mains plug or an appliance coupler is
•
used as the disconnect device, the disconnect device
shall remain readily operable.
•
Visible and invisible laser radiation when open. Avoid
exposure to beam.
About Progressive Scan
Consumers should note that not all high
de nition television sets are fully compatible
with this product and may cause artifacts to be
displayed in the picture. In case of 525 or 625
progressive scan picture problems, it is
recommended that the user switch the
connection to the ‘standard de nition’ output. If
there are questions regarding our TV set
compatibility with this model 525p and 625p
DVD player, please contact our customer
service center.
Recycle notice
Your product is designed and manufactured
with highly quality material and components,
which can be recycled and reused. When this
crossed-out wheeled bin symbol is attached to
a product, it means the product is covered by
the European Directive 2002/96/EC.
This product complies with the radio
interference requirements of the European
Community. This product complies with the
requirements of the following directives and
guidelines: 2006/95/EC, 2004/108/EC.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
4 EN
Trademark Notice
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
Copyright notice
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorised by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
English
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Important
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
DivX, DivX Ultra Certi ed, and associated logos
are trademarks of DivX, Inc. and are used under
license.
Of cial DivX® Ultra Certi ed product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX®
media les and the DivX® Media Format.
Plays DivX® video with menus, subtitles and
audio tracks.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
HDMI, and HDMI logo and High-De nition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
EN 5
2 Your DVD
ALL
player
Screen t
View the movie in full screen on any TV with
this DVD player.
Congratulations on your purchase, and
welcome to Philips! To fully bene t from the
support that Philips offers, register your product
at www.philips.com/welcome.
This DVD player offers higher picture quality
video play for an amazing viewing experience.
Features highlight
Video upscaling to 1080p
You can now watch the DVDs in the highest
picture quality available for your HDTV. This
DVD player offers full high-de nition video play
up to 1080p resolution for an amazing viewing
experience. A highly detailed picture and
increased sharpness delivers a more true-to-life
picture.
Hi speed USB 2.0 link
Simply plug your USB ash drive into the USB
socket to play your MP3/WMA/JPEG/DivX les
to enjoy the music play in superb sound quality.
Create MP3 les
Convert your favourite audio tracks from an
audio CD into MP3 format. The created MP3
les are saved in your USB device.
Karaoke scoring function
Karaoke scoring gives a score for each
performance. Have your singing performance
scored for even more karaoke fun at home!
Region codes
Your DVD player plays discs with the following
region codes.
EasyLink
EasyLink uses the HDMI CEC (Consumer
Electronics Control) industry standard protocol
to share functionality with all HDMI CEC
compliant devices over HDMI. It enables the
connected devices to control each other with a
single remote control.
Note
EasyLink (HDMI CEC) is only applicable with cer tain •
criteria. Terms and conditions may vary by product.
Consult your product dealer for information.
Philips does not guarantee 100% interoperability
•
with all HDMI CEC devices.
DVD region code Countries
Russia
6 EN
Product overview
Remote control
English
Main unit
a 2 (Standby-on)
Turn on the DVD player or switch to •
standby mode.
b Disc compartment
c Display panel
1
2
3
4
5
31 2
5
4
7
6
6
7
8
9
10
18
17
16
15
14
13
12
11
Your DVD player
d Z (Open/Close)
Open or close the disc compartment.•
e u (Play/Pause)
Start, pause or resume disc play.•
f (USB) socket
Connect a USB ash drive.•
g MIC
Audio input from a microphone.•
a 2 (Standby-On)
Turn on the DVD player or switch to •
standby mode.
Press and hold to turn off the DVD •
player and all HDMI CEC compliant
devices.
b Z (Open/Close)
Open or close the disc compartment.•
c DISC MENU
Access or exit the disc menu.•
Switch to disc mode.•
For VCD/SVCD, turn PBC (Playback •
Control) on or off in PBC mode.
EN 7
d v V b B (Navigation buttons)
m AUDIO/CREATE MP3
Navigate through the menus.•
Search fast-forward (• B) or fast-
backward (b). Press repeatedly to
change the search speed.
Search slow-forward (• v) or slowbackward (V). Press repeatedly to
change the search speed.
e 2 BACK
Return to the previous display menu.•
For DVD, navigate to the title menu.•
For VCD version 2.0 or SVCD with •
PBC turned on, return to the menu.
f í/ë (Previous/Next)
Skip to the previous or next title, •
chapter, or track.
Press and hold for fast-backward or •
fast-forward search.
Select an audio language/channel.•
Access the menu to create MP3.•
n x (Stop)
Stop disc play.•
o u (Play/Pause)
Start, pause or resume disc play.•
p INFO
For disc, display the current status or •
disc information.
For slideshows, display a thumbnail view •
of photo les.
q OK
Con rm an entry or selection.•
r SETUP
Access or exit the setup menu.•
g (USB)
Switch to USB mode and display the •
content.
h Numeric buttons
Select an item to play.•
i SUBTITLE
Select DVD or DivX subtitle language.•
j , ZOOM
Fit the picture format to the TV screen.•
Zoom in or out of the picture.•
k VOCAL
Change the audio channel of a karaoke •
disc.
l KARAOKE
8 EN
Access or exit the karaoke menu.•
3 Connect
Select the best video connection that the TV can
support.
Make the following basic connections to use the
DVD player.
Basic connections:
Video cables•
Audio cables•
Optional connections:
Audio to other devices:•
Digital ampli er/receiver•
Analogue stereo system•
Note
Refer to the type plate at the rear or bottom of the •
product for identi cation and supply ratings.
Before you make or change any connections, ensure
•
that all the devices are disconnected from the power
outlet.
Option 1:• Connect to HDMI socket (for a
HDMI, DVI or HDCP-compliant TV).
Option 2:• Connect to component video
sockets (for a standard TV or Progressive
Scan TV).
Option 3:• Connect to video (CVBS) socket
(for a standard TV).
Note
You must connect this • DVD player directly to a
TV.
Option 1: Connect to HDMI socket
English
Connect
Tip
Different types of connectors may be used to •
connect this product to your TV, depending on
availability and your needs. A comprehensive
interactive guide to help you connect your product is
available at www.connectivityguide.philips.com.
Connect video cables
Connect this DVD player to the TV to view
disc play.
HDMI IN
HDMI OUT
1 Connect a HDMI cable (not supplied) to
the HDMI OUT socket on this DVD
player and the HDMI input socket on the
TV.
Use a HDMI-DVI adaptor in case the •
TV has only a DVI connection.
Note
If the device supports HDMI CEC, you can control •
compliant devices with a single remote control (see
chapter ‘Use Philips EasyLink’).
This type of connections provide best picture quality.•
Tip
EN 9
Option 2: Connect to component
Option 3: Connect to video (CVBS)
video sockets
Pb
Pr
Y
COMPONENT VIDEO OUT
Pr
COMPONENT
Pb
VIDEO IN
Y
1 Connect the component video cables (not
supplied) to the Y Pb Pr sockets on this
DVD player and the component video
input sockets on the TV.
If a progressive scan TV is used, you •
may turn on the progressive scan mode
(see chapter ‘Turn on Progressive Scan’
for details).
socket
VIDEO IN
1 Connect a composite video cable
(supplied) to the TV OUT socket on this
DVD player and the video input socket on
the TV.
Tip
The video input socket on the TV may be labelled as •
A/ V IN, VIDEO IN, COMPOSITE or BASEBAND.
This type of connection provides standard picture
•
quality.
Tip
The component video input sockets on the T V may •
be labelled as Y Pb/Cb Pr/Cr or YUV.
This type of connection provides good picture
•
quality.
Connect audio cables
Connect the audio from this DVD player to the
TV to allow sound output through the TV.
AUDIO IN
1 Connect the audio cables (supplied) to the
AUDIO OUT L/R sockets on this DVD
player and the audio input sockets on the
TV.
10 EN
Route audio to other devices
Route the sound from this DVD player to other
devices to enhance audio play.
Connect to digital ampli er/receiver
DIGITAL IN
DIGITAL
OUT
COAXIAL
1 Connect a coaxial cable (not supplied) to
the COAXIAL/DIGITAL OUT socket on
this DVD player and the COAXIAL/
DIGITAL input socket on the device.
Tip
You can optimise the audio output (see chapter •
‘Adjust settings’ - [ Audio Setup ] > [ Analog Output
]) for details.
Connect USB device
1 Connect the USB ash drive to the
(USB) socket on this DVD player.
Note
English
Connect
Tip
You can optimise the audio output (see chapter •
‘Adjust settings’ - [ Audio Setup ] > [ Digital Audio
]) for details.
Connect to analogue stereo system
AUDIO IN
This DVD player can only play/view MP3, WMA, •
DivX or JPEG les that are stored on such devices.
Press
• to access the content and play the les.
Connect to power outlet
Warning
Risk of product damage! Ensure that the power •
supply voltage corresponds to the voltage printed on
the back or the underside of the DVD player.
1 Connect the power cord to the power
outlet.
The DVD player is ready to be set up
for use.
1 Connect the audio cables (supplied) to the
AUDIO OUT L/R sockets on this DVD
player and the audio input sockets on the
device.
EN 11
4 Get started
Prepare the remote control
Navigate through the menu
1 Point the remote control directly at the
remote sensor on this DVD player and
select the desired function.
1 Push to open the battery compartment
cover.
2 Insert two R03 or AAA batteries type with
correct polarity (+/-) as indicated.
3 Close the battery compartment.
Caution
Remove batteries if they are exhausted or if the •
remote control is not to be used for a long time.
Do not mix batteries (old and new or carbon and
•
alkaline, etc.).
Batteries contain chemical substances, they should
•
be disposed of properly.
2 Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button Action
v V
b B
OK
Move up or down.
Move left or right.
Con rm a selection.
Enter numbers.
12 EN
Find the correct viewing
channel
Select menu display language
Press 2 to turn on the DVD player.
1
2 Turn on the TV and switch to the correct
video-in channel.
You may go to the lowest channel on •
the TV, then press the Channel Down
button on the TV remote control until
you see the Video In channel.
You may press • ° button repeatedly
on the TV remote control.
Usually this channel is between the •
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO, etc..
Tip
See the TV user manual on how to select the correct •
input on the TV.
•
If the audio output of this DVD player is routed
to other audio device (such as audio system
or receiver), turn on the audio device to the
appropriate audio input channel. Refer to the device
user manual for details.
Note
You can skip this setting if this DVD player is •
connected to a HDMI CEC compliant TV. It switches
automatically to the same OSD menu language as
per your TV setting.
1 Press SETUP.
[ General Setup ] menu is displayed.
2 Select [ OSD Language ], then press B.
General Setup
Disc Lock
OSD Language
Sleep Timer
Auto Standby
DivX(R) VOD Code
The language options are different •
depending on your country or region.
It may not correspond to the illustration
shown here.
Auto (Rus)
English
Polski
Русский
English
Get started
3 Press vV to select a language, then press
OK.
Tip
You can set the default language for DVD audio •
and disc menu, see chapter ‘Adjust settings’ - [
Preferences ] for details.
EN 13
Turn on Progressive Scan
Connect a progressive scan TV with
component video sockets (see chapter
‘Connect video cables - Option 2: Connect to
component video sockets’ for details).
1 Turn on the TV to the correct viewing
channel for this DVD player.
2 Press SETUP.
3 Press V to select [ Video Setup ].
7 You can now turn on the progressive scan
mode on the TV (see the TV user manual).
Note
The progressive scan setting will not be available •
when the HDMI video signal is detected.
During play, when progressive scan mode is on for
•
both this DVD player and the TV, distorted picture
may display. Turn off the progressive scan feature on
both this DVD player and the TV.
4 Select [ Progressive ] > [ On ]
then press
,
OK.
A warning message is displayed.
Video Setup
TV System
TV Display
Progressive
Picture Setting
HD JPEG
HDMI Setup
On
Off
5 To proceed, select [ OK ] and press OK.
The progressive setup is complete.
Note
If a blank /distorted screen is displayed, wait for 15 •
seconds for the auto recover.
•
If no picture displayed, turn off the progressive scan
mode as follows:
1) Press Z to open the disc compartment.
2) Press the numeric button ‘1’.
6 To exit the menu, press SETUP.
14 EN
Loading...