Philips DVDR-70 Service manual

DVD-Video Recorder DVDR70 & DVDR75/0x1

Contents Page Contents Page

1 Technical Specifications and Connection

Facilities Diversity Matrix 2

PCB Locations 5 2 Safety Information, General Notes 6 3 Directions for Use 8 4 Mechanical Instructions 45 5 Diagnostic Software 49 6

Block Diagrams, Waveforms, Wiring Diagram

Wiring Diagram 92

Waveforms 93

Testpoints 97 7

Circuit Diagrams and PWB Layouts

Display Panel (Diagram 1) 102

Front Connector (FC) (Diagram 2) 103

Standby Panel (STBY) (Diagram 3) 107

Tray Left Panel (TRL) (Diagram 4) 108

Tray Right Panel (TRR) (Diagram 5) 109

Analog Board:Fronted Video (FV) (Diagram 1) 110

Analog Board: In / Out Video (IOV) (Diagram 2) 111

Analog Board: In / Out Audio (IOA) (Diagram 3) 112

An. Brd for VAE8020: Power Supply (PS)(Diagram 4) 113

An. Brd for VAD8031: Power Supply (PS) (Diagram 5) 114

Analog Board: Multi Sound Processing (MSP)

Analog Board: VPS (Diagram 6) 116

Analog Board: Follow Me (FOME) (Diagram 7) 116

Analog Board: Digital In/Out (DIGIO) (Diagram 8) 117

Analog Board: Audio Converter 603 3033 (DAC_ADC)

Analog Board: Audio Converter 603 3028 (DAC_ADC)

Copyright 2002 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

(Diagram 5)

(Diagram 9) (Diagram 10)

102

115

118 119

UP Sub Board: Central Controler (CECO) UP Sub Board: Fan Control (FACO) (Diagram 12) 129

DVIO Board: 1394 Interface (Diagram 1) 132 DVIO Board: Link + Codec (Diagram 2) 133 DVIO Board: uP Part (Diagram 3) 134 DVIO Board: Interface + DAC (Diagram 4) 135 DVIO Board: Clock (Diagram 5) 136 Digital Board 1.5: VSM Buffer Memory and Bit Engine Interface (Diagram 1) Digital Board 1.5: AV Dec. STI5519 (Diagram 2) 141 Digital Board 1.5: AV Decoder Mem. (Diagram 3) 142 Digital Board 1.5: Video Enc. Empress (Diagram 4) 143 Digital Board 1.5: VIP CVBS Y/C Video Input

Digital Board 1.5: Analog Board Cons. Video In/Out Digital Board 1.5: Progressive Scan (Diagram 7) 146

Digital Board 1.5: Progressive Scan (Diagram 8) 147 Digital Board 1.5: Power, Clock and Reset (Diagram 9) 148 DB Chrysalis 2.1: IDE, UARTS, RESET, BE(Diagram 1) 155 DB Chrysalis 2.1: 1394 (Diagram 2) 156 DB Chrysalis 2.1: Audio PLL (Diagram 3) 157 DB Chrysalis 2.1: Chrysalis (Diagram 4) 158 DB Chrysalis 2.1: 1.8V Power (Diagram 5) 159 DB Chrysalis 2.1: Prog. scan DAC (Diagram 6) 160 DB Chrysalis 2.1: Flash SDRAM EEPROM(Diagram 7) 161 DB Chrysalis 2.1: Video IO (Diagram 8) 162 DB Chrysalis 2.1: VIPs (Diagram 9) 163

8 Alignments 167 9 Circuit-, IC Descriptions and List

of Abbreviations

10 Spare Parts List 246 11 Revision List 260

For service manual of Basic Engine VAE8020 please refer to 3122 785 12473. For service manual of Basic Engine VAD8031 please refer to 3122 785 13680.

(Diagram 11)

(Diagram 5) (Diagram 6)

128

140

144 145

170

Published by GH 0393 Service PaCE Printed in the Netherlands Subject to modification EN 3122 785 13322

EN 2 DVDR70 & DVDR75/0x11.

Technical Specifications and Connection Facilities

1. Technical Specifications and Connection Facilities

1.1 Diversity Matrix for sets with drive VAE8020 (AV2)

Type DVDR 75/001 75/021 75/051 70/001 70/021 70/051

Version A' Lead X X X

A Lead X X X

DVIO DVIO 1.8 <VN05 <VN05 <VN05

Digital Board

(Chrysalis) 2.1

Digital Board

(Empress) 1.5

Basic Engine VAE 8020 XXXXXX

UP Sub AL E1 X X X X X X

3103 603 3033

Analog-Board

3103 603 3028

Display Board DC1 AL X X X X X X

E1 >VN04 >VN04 >VN04 E2 >VN04 >VN04 >VN04

E1 <VN05 <VN05 <VN05 <VN05 <VN05 <VN05

E2/PS

E1/PS AL E2 >VN03 >VN03 AL E1 >VN02 >VN03 >VN02 >VN03

<VN03 <VN04 <VN03 <VN04

<VN04 <VN04

Remarks:

<VN03 ... This module is used in sets with production codes VN01 and VN02. Please see the type plate of the set for the production code.

>VN02 ... This module is used in sets with production code VN03 and higher.

E1 ... Digital Board Chrysalis Version Euro 1 for sets with DV input E2 ... Digital Board Chrysalis Version Euro 2 for sets without DV input

AL E1/PS ... Analog Board version A-Lead Euro 1, used from production start onwards. AL E2/PS ... Analog Board version A-Lead Euro 2 for UK, used from Production Start onwards.

The Analog Board versions "AL Ex/PS" are based on the PWB layout code 3103 603 3033. This layout code can also be seen on the underside of the Analog Board in the copper near the power supply part.

AL E1 ... Analog Board version A-Lead Euro 1 replaces "AL E1/PS" at a certain production date. AL E2 ... Analog Board version A-Lead Euro 2 for UK replaces "AL E2/PS" at a certain production date.

The Analog Board versions "AL Ex" are based on the PWB layout code 3103 603 3028. The main difference to the Analog Board used at production start is the used audio digital/analogue converter; see Analog Board circuit diagram 9.

1.2 Diversity Matrix for sets with drive VAD8031 (AV3)

Sets with VAD8031 can be identified by the production code starting with VN1A, (then VN1B, VN1C...) and by the presence of a set fan.

Type DVDR 75/001 75/021 75/051 70/001 70/021 70/051

Version A' Lead X X X

A Lead X X X

Digital Board

(Chrysalis) 2.1

BasicEngine VAD 8031 X X X X X X

UP Sub AL E1/AV3 X X X X X X

Analog-Board

Display Board DC1 ALXXXXXX

use PWB drawing

603 3028

E1 /AV3 X X X E2 /AV3 X X X

AL E2/AV3 X X AL E1/AV3 X X X X

Technical Specifications and Connection Facilities

EN 3DVDR70 & DVDR75/0x1 1.

1.3 General:

Mains voltage : 198V-276V Mains frequency : 43 Hz - 63Hz Power consumption mains : 28 W Power consumption standby : < 7 W Power consumption low power stand-by : < 3 W

1.4 RF Tuner

Test equipment:Fluke 54200 TV Signal generator Test streams:PAL BG Philips Standard test pattern

1.4.1 System:

PAL B/G, PAL D/K, SECAM L/L’, PAL I

1.4.2 RF - Loop Through:

Frequency range : 45 MHz - 860 MHz Gain: (ANT IN - ANT OUT) : -6 dB to 0dB

1.4.3 Radio Interference:

input voltage /3 tone method (+40 dB min) : no limit

1.4.4 Receiver:

PLL tuning with AFC for optimum reception Frequency range: : 45.25 MHz - 857 MHz Sensitivity at 40 dB S/N : ≥ 60dBµV at 75Ω

(video unweighted )

1.4.5 Video Performance:

Channel 25 / 503,25 MHz, Test pattern: PAL BG PHILIPS standard test pattern, RF Level 74 dBV Measured on SCART 1 Frequency response: : 0 - 4.00 MHz +0-4dB Group delay ( 0.1 MHz - 4.4 MHz ) : 0 nsec ± 150nsec

1.4.6 Audio Performance:

Audio Performance Analogue - HiFi:

Frequency response at SCART 1 (L+R) output: : 100 Hz - 12 kHz / 0±

3dB S/N according to DIN 45405, 7, 1967 : and PHILIPS standard test pattern video signal: : FM: ≥ 50dB; AM ≥

45dB, unweighted Harmonic distortion ( 1 kHz, ± 25 kHz deviation ): : FM ≤ 1.5%; AM ≤ 2%

Audio Performance NICAM:

Frequency response at SCART 1(L+R) output: : 40 Hz - 15 kHz 0 ±

3dB S/N according to DIN 45405, 7, 1967 : and PHILIPS standard test pattern video signal: : ≥ 60 dB unweighted Harmonic distortion (1 kHz): : ≤ 0.5 %

1.4.7 Tuning

Automatic Search Tuning

scanning time without antenna : typ. 3 min. PAL stop level (vision carrier) : ≥ 37dBµV

Maximum tuning error of a recalled program : ± 62.5 kHz Maximum tuning error during operation : ± 100 kHz

Tuning Principle

automatic B,G, I, DK and L/L’detection manual selection in "STORE" mode

1.5 Analogue Inputs

1.5.1 SCART 1 (Connected to TV)

Pin Signals: 1 - Audio R 1.8V RMS  2 - Audio R  3 - Audio L 1.8V RMS  4 - Audio GND  5 - Blue/Chroma GND  6 - Audio L  7 - Blue out/ Chroma in 0.7Vpp ± 0.1V into 75 Ohm (*)  8 - Function switch <2V = TV

>4.5V / <7V = asp. ratio 16:9 DVD

>9.5V / <12V = asp. ratio 4:3 DVD  9 - Green GND  10 - P50 control  11 - Green 0.7Vpp ± 0.1V into 75 Ohm (*) 12 - Nc 13 - Red/Chroma GND  14 - fast switch GND  15 - Red out/ Chroma out 0.7Vpp ± 0.1V into 75 Ohm (*)

± 3dB 0.3Vpp Chroma (burst)  16 - fast switch RGB/ CVBS or Y <0.4V into 75 Ohm = CVBS

>1V / <3V into 75 Ohm = RGB  17 - Y/CVBS GND OUT  18 - Y/CVBS GND IN  19 - CVBS/Y 1Vpp ± 0.1V into 75 Ohm (*)  20 - CVBS/Y  21 - Shield 

1.5.2 SCART 2 (Connected to AUX)

Pin Signals: 1 -Audio R 1.8V RMS  2 -Audio R  3 -Audio L 1.8V RMS  4 -Audio GND  5 -Blue/Chroma

GND  6 -Audio L  7 -Blue in/

Chroma out ± 3dB 0.3Vpp Chroma (burst)  8 -Function

switch  9 -Green GND  10 -P50 control  11 -Green  12 -Nc 13 -Red/Chroma

GND  14 -fast switch

GND  15 -Red in/

Chroma in 

EN 4 DVDR70 & DVDR75/0x11.

Technical Specifications and Connection Facilities

16 -fast switch

RGB/ CVBS or Y 

17 -CVBS GND

OUT 

18 -CVBS GND

IN 

19 -CVBS/Y/RGB

sync 1Vpp ± 0.1V into 75 Ohm (*)  20 -CVBS/Y  21 -Shield 

(*) for 100% white

1.5.3 Audio/Video Front Input Connectors

Audio

Input voltage : 2 Vrms Input impedance : >10kΩ

Video - Cinch

Input voltage : 1 Vpp ± 3dB Input impedance : 75 Ω

Video - YC (Hosiden)

Input voltage Y : 1Vpp ± 3dB Input impedance Y : 75 Ω Input voltage C : burst 300 mVpp ± 3

Input impedance C : 75 Ω

1.6 Video Performance

All outputs loaded with 75 Ohm SNR measurements over full bandwidth without weighting.

1.6.1 SCART (RGB)

SNR : > -65 dB on all output Bandwidth : 4.8 MHz ± 2dB

Intermodulation distortion : >70dB Mute (spin-up, pause, access) : >85dB Outband attenuation: : >40dB above 25kHz

1.8 Digital Output

1.8.1 Coaxial

CDDA/ LPCM (incl MPEG1) : according IEC958 MPEG2, AC3 audio : according IEC1937 DTS : according IEC1937,

amendment 1

1.9 Digital Video Input (IEEE 1394)

1.9.1 Applicable Standards

Implementation according: IEEE Std 1394-1995 IEC 61883 - Part 1 IEC 61883 - Part 2 SD-DVCR (02-01-1997) Specification of consumer use digital VCR’s using 6.3 mm magnetic tape - dec.1994 Mechanical connection according: Annex A of 61883-1

1.10 P50 System Control

Via SCART pin nr 10

1.11 Dimensions and Weight

Height of feet : 10mm Apparatus tray closed : WxDxH :435 x 324.5 x

88cm

Apparatus tray open : WxDxH :435 x 366 x

88cm Weight without packaging : app. 4 kg ± 0.5 kg Weight in packaging : app. 6.5 kg

1.7 Audio Performance CD

1.7.1 Cinch Output Rear

Output voltage 2 channel mode : 2Vrms ± 2dB Channel unbalance (1kHz) : <1dB Crosstalk 1kHz : >95dB Crosstalk 20Hz-20kHz : >85dB Frequency response 20Hz- 20kHz : ±0.2dB max Signal to noise ratio : >95 dB Dynamic range 1kHz : >85dB Dynamic range 20Hz-20kHz : >80dB Distortion and noise 1kHz : >85dB Distortion and noise 20Hz-20kHz : >75dB Intermodulation distortion : >77dB Mute : >95dB Outband attenuation: : >40dB above 30kHz

1.7.2 Scart Audio

Output voltage 2 channel mode : 1.6Vrms ± 2dB Channel unbalance (1kHz) : <1dB Crosstalk 1kHz : >85dB Crosstalk 20Hz-20kHz : >70dB Frequency response 20Hz- 20kHz : ± 0.2dB max Signal to noise ratio : >85 dB Dynamic range 1kHz : >75dB Dynamic range 20Hz-20kHz : >70dB Distortion and noise 1kHz : >75dB Distortion and noise 20Hz-20kHz : >65dB

1.12 Laser Output Power & Wavelength

1.12.1 DVD

Output power during reading : 0.8mW Output power during writing : 20mW Wavelength : 660nm

1.12.2 CD

Output power : 0.3mW Wavelength : 780nm

Technical Specifications and Connection Facilities

1.13 PCB Locations

EN 5DVDR70 & DVDR75/0x1 1.

Display Board

EPG Board

DVIO Board

Basic Engine

IOE Board

Up Sub Board

Analog Board

Digital Board

Remarks:

The EPG Board and the In/Out Extension Board IOE are only used in the DVDR80.

The DVIO Board is only present in the DVDR75 and only in combination with the Digital Board 1.5 (Empress). It is not present in DVDR75 with Digital Board 2.1 (Chrysalis).

TR 06002_001

300103

EN 6 DVDR70 & DVDR75/0x12.

Safety Information, General Notes

2. Safety Information, General Notes

2.1 Safety Instructions

2.1.1 General Safety

Safety regulations require that during a repair:

• Connect the unit to the mains via an isolation transformer.

• Replace safety components, indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard.

Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points:

• Route the wires/cables correctly, and fix them with the mounted cable clamps.

• Check the insulation of the mains lead for external damage.

• Check the electrical DC resistance between the mains plug and the secondary side:

1. Unplug the mains cord, and connect a wire between

the two pins of the mains plug.

2. Set the mains switch to the 'on' position (keep the

mains cord unplugged!).

3. Measure the resistance value between the mains plug

and the front panel, controls, and chassis bottom.

4. Repair or correct unit when the resistance

measurement is less than 1 MΩ.

5. Verify this, before you return the unit to the customer/

user (ref. UL-standard no. 1492).

6. Switch the unit ‘off’, and remove the wire between the

two pins of the mains plug.

2.1.2 Laser Safety

This unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury).

2.2 Warnings

2.2.1 General

• All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, ). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: – Complete kit ESD3 (small tablemat, wristband,

connection box, extension cable and earth cable) 4822 310 10671.

– Wristband tester 4822 344 13999.

• Be careful during measurements in the live voltage section. The primary side of the power supply (pos. 1005), including the heatsink, carries live mains voltage when you connect the player to the mains (even when the player is 'off'!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A 'lightning stroke' and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply.

• Never replace modules, or components, while the unit is ‘on’.

2.2.2 Laser

• The use of optical instruments with this product, will increase eye hazard.

• Only qualified service personnel may remove the cover or attempt to service this device, due to possible eye injury.

• Repair handling should take place as much as possible with a disc loaded inside the player.

• Text below is placed inside the unit, on the laser cover shield:

Laser Device Unit

Type : Semiconductor laser

GaAlAs

Wavelength : 650 nm (DVD)

: 780 nm (VCD/CD)

Output Power : 20 mW

(DVD+RW writing)

: 0.8 mW

(DVD reading)

: 0.3 mW

(VCD/CD reading)

Beam divergence : 60 degree

Figure 2-1

Note: Use of controls or adjustments or performance of

procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.

CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN VARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU

Figure 2-2

2.2.3 Notes

Dolby

Manufactered under licence from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.

Figure 2-3

Trusurround

TRUSURROUND, SRS and symbol (fig 2-4) are trademarks of SRS Labs, Inc. TRUSURROUND technology is manufactured under licence frm SRS labs, Inc.

Figure 2-4

Safety Information, General Notes

Video Plus

“Video Plus+” and “PlusCode” are registered trademarks of the Gemstar Development Corporation. The “Video Plus+” system is manufactored under licence from the Gemstar Development Corporation.

Figure 2-5

Macrovision

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be autorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

EN 7DVDR70 & DVDR75/0x1 2.

EN 8 DVDR70 & DVDR75/0x13.

3. Directions For Use

Briefly press the button during playback: Previous chapter/film or

previous title

Hold down the button: Search backwards

Hold down button during still picture, slow motion backwards

Briefly press the button during playback: Next chapter/film or next title

Hold down the button: Search forwards

Hold down button during still picture, slow motion forwards

(TIMER)

N Select previous title/search backwards :

O Select next title/search forwards :

STOP h Stop: Stop playback/recording, except with programmed recordings

Hold down button, opens and closes the disc tray.

Directions For Use

DVD recorder switches to pause. You will see a still picture.

If this button is pressed during recording, the DVD recorder will also

switch to pause.

TV VOLUME q TV volume: Increase TV volume

AUDIO Audio: Select the audio language. For recording language 1 or 2

REC/OTR n Record: Record the current TV channel

PAUSE 9 Pause (still picture): If this button is pressed during playback, the

Additional TV functions

This will only work with TV sets with the same remote control code *RC5) (e.g. Philips TV sets)

TV VOLUME r TV volume: Reduce TV volume

For the following functions you need to hold down the button at the side DVD/TV and then

select the function you need with the appropriate button.

STANDBY m Switching the TV off:

0..9 Number buttons:0-9

CH+ A TV programme number: To select a higher programme number

CH- B TV programme number: To select a lower programme number

tuner) in the DVD recorder (TV picture on the TV set) and playback on

MONITOR Monitor: This button lets you switch between the TV receiver (internal

The remote control

the DVD recorder.

STANDBY m Switch on or off: To switch set on or off, interrupt menu function,

ENGLISH

interrupt a programmed recording (TIMER)

to the TV set. This lets you watch the picture from any unit connected

TV/DVD TV/DVD switch: Switches the scart socket EXT 2 AUX-I/O directly

to this scart socket (set-top box', video recorder or satellite receiver)

and at the same time record from another source.

If you have not connected a device to the EXT 2 AUX-I/O socket, use

this button to switch between TV reception and the DVD recorder.

But this only works if you use a scart cable to connect the TV set to

your DVD recorder ( EXT 1 TO TV-I/O socket) and your TV set

responds to this switch-over.

'(Chapter) directly from the

'(Title)/'

menu bar

T/C Title/Chapter: Choose the '

/without

or to alter or clear a programmed TIMER

If 'INFO' appears in the display, the index menu from a recorded disc or

an introductory film will be shown. In this case, this function is not

available.

PLAY MODE Playback type: Choose between repeat, shuffle play and intro-scan

REC MODE Record type (quality): To select the maximum possible record time

the screen)

0..9 Number buttons:0-9

DISC-MENU Disc menu: To show the DVD menu or the index screen

SYSTEM-MENU System menu: Call up/cancel the main menu (menu bar at the top of

SELECT Select: Select function/value

OK Store/confirm: To store or confirm entry

DC Cursor keys : Cursor left, right

CH+ A Cursor buttons/Plus : Cursor up/ Next programme number

CH- B Cursor buttons/Minus : Cursor down / Previous programme number

ShowView

TIMER TIMER: To make a TIMER programming with ShowView

chapter markers

FSS & EDIT: For displaying the edit menu for DVD+R(W) discs, for setting

RETURN Back: Return to previous menu on a video CD (VCD). This also works

with some DVDs.

CLEAR Delete: To delete last entry or clear programmed recording (TIMER)

PLAY G Playback: To play a recorded disc.

Back of the unit

4MAINS Mains socket: Connection to the mains supply (230V/50Hz)

ANTENNA IN Aerial input: Connection of the aerial

Directions For Use

set-top box, video recorder, camcorder, etc.)

TV OUT Aerial output: Connection of the TV set

EXT 2 AUX-I/O Scart socket 2: Connection of an additional device (satellite receiver,

EXT 1 TO TV-I/O Scart socket 1: Connection of a TV set. RGB output

Output sockets (AUDIO/VIDEO OUT)

EN 9DVDR70 & DVDR75/0x1 3.

Multi-function display/text line

•) Clock

•) Disc/title playing time

•) OTR switch-off time

•) Title name

•) Display of the programme number of the TV channel/playing

time/channel name/function.

Video output (yellow socket): Connecting a TV set with a video

input (CVBS, Composite Video)

set with audio input sockets or connection of an additional device

OUT S-VIDEO (Y/C) SVideo output: Connection of an S-Video-compatible TV set

OUT VIDEO

OUT L AUDIO R Analogue audio output (white/red socket): Connection of a TV

(CVBS)

Output socket (DIGITAL AUDIO OUT)

Digital audio output: Connection of a digital audio device

DIGITAL AUDIO

(amplifier/receiver)

OUT

The symbols on your DVD recorder

display

These symbols can light up on your DVD recorder display:

•) Display of information and alerts

Front of the device

ENGLISH

STANDBY/ON m Switch on or off: To switch off or on, interrupt a function, interrupt a

programmed recording (TIMER)

OPEN/CLOSE J Open/close disc tray: Open/close disc tray

RECORD Record: Record the current TV channel

G Playback: To play a recorded disc

N Select previous title/search backwards

O Select next title/search forwards

h Stop: Interrupt playback/recording

Behind the flap at the righthand corner on

S-VIDEO SVideo socket: Connection of SVHS/Hi8 camcorders or SVHS/Hi8

the front

video recorders (programme number 'CAM1')

Video input socket: Connection of camcorders or video recorders

(programme number 'CAM1')

VIDEO

Yellow socket

Audio input socket left/right : Connection of camcorders or video

recorders (programme number 'CAM1')

left AUDIO right

White/red socket

Switching between the S-VIDEO and VIDEO sockets takes place automatically. If both sockets

are in use, the signal at the S-VIDEO socket has priority.

Connecting a digital camcorder or other suitable device (programme

DV IN iLink/DV socket (digital video input, IEEE 1394, FireWire):

number 'CAM2').

EN 10 DVDR70 & DVDR75/0x13.

Directions For Use

recordings).

EMPTYDISC The disc inserted is either new or has been completely erased (no

PROTECTED The disc is protected against recording.

MAX TITLE The maximum number of titles per disc has been reached. The

maximum number of titles per disc is 48.

maximum number of chapters per title is 124.

MAX CHAP The maximum number of chapters per title/disc has been reached. The

DISC FULL The disc is full. There is no space for new recordings

PAL DISC A disc with PAL recordings has been inserted. The machine is trying to

ENGLISH

record an NTSC signal. Insert a new disc or one that contains NTSC

recordings.

NTSC DISC A disc with NTSC recordings has been inserted. The machine is trying

to record a PAL signal. Insert a new disc or one that contains PAL

recordings.

recording.

RECORDING An illegal action (e.g. OPEN/CLOSE J button) was attempted during

FREETITLE Playback was started for an empty title or the following title is empty.

disc. This message appears if an attempt is made to insert a chapter

marker ( FSS & button).

DISC LOCK An attempt has been made to record during playback of a protected

please clean the disc or use a new one.

For instructions on how to clean a disc see the section on 'Cleaning the

DISC ERR An error occurred when writing the title. If this error keeps occurring,

discs' in the next chapter.

DISC WARN An error occurred when writing the title. Recording was continued; the

error was skipped

SETUP After the automatic search the menu for setting the date/time will

appear on the screen.

WAIT 01 During the automatic search the TV channels found are counted

BLOCKED The disc tray cannot be closed/opened.

(SAFE RECORD).

SAFE REC The new recording will be added at the end of all the other recordings

EASYLINK Data is being transferred from the 'EasyLink' TV.

POST-FORMAT Post format

Disc bar: Displays the current position on the disc (disc pointer).

Play/Record: Single flashing segment at the current position.

Pause: Flashing segment on both sides of the current position.

IIIIIIIIIIIIIII

Stop: Illuminated segment at the current position.

A satellite recording has been programmed.

SAT

A recording (timer) has been programmed

A remote control signal has been received

TIMER

o(((

Video programming system / programme delivery control: A VPS or

PDC code will be transmitted for the selected TV program

During playback a HiFi/2 channel tone was detected or a HiFi/2 channel

VPS/PDC

LANG II

tone was received. 'I' or 'II' lights up depending on which sound channel

has been selected

Messages in the DVD recorder display

read the paragraph on 'Initial installation' in 'Installing your DVD

recorder'.

IS TV ON? The DVD recorder is in initial installation mode. Switch the TV on, then

The following messages may appear in your DVD recorder display

READING

NO SIGNAL No input signal available (signal inadequate or unstable)

MENU The menu on the screen is active

OPENING Disc tray opening

TRAY OPEN Disc tray open

CLOSING Disc tray closing

READING Disc being read

MENU UPDT Once recording has been successfully completed the table of contents is

created.

INIT MENU The menu structure is created after the first recording has been made

on a new disc

COPY PROT You have tried to copy a copy-protected DVD/video cassette.

WAIT Please wait until this message disappears. The DVD recorder is busy

performing a task.

cannot be read.

Information about the inserted DVD is displayed on the screen

compatible

NO DISC A disc has not been inserted for recording. If a disc has been inserted, it

INFO

BUSY The DVD recorder is processing the changes to make them DVD

ERASING The entire disc is erased

Directions For Use

EN 11DVDR70 & DVDR75/0x1 3.

Connecting the DVD recorder

When you install your DVD recorder for the first time, select one of the following options:

'Connecting with a scart cable and Easy Link'

If your TV set is equipped with 'Easy Link, Cinema Link, NexTView Link, Q-Link, Smart Link,

Megalogic, Datalogic, ...' and you wish to use a scart cable.

'Connecting with a scart cable without Easy Link'

If your TV set is not equipped with 'Easy Link, Cinema Link, NexTView Link, Q-Link, Smart Link,

Megalogic, Datalogic, ...' and you wish to use a scart cable.

'Connecting with an SVideo(Y/C)cable'

If your TV set is equipped with an S-Video(SVHS) socket.

'Connecting with video(CVBS) cable'

If your TV set is equipped only with an video(CVBS) socket.

ENGLISH

Connecting with a scart cable and

'Easy Link'

Your DVD recorder can exchange information with your TV set using 'Easy Link'. Your TV

channels can also be transferred in the same order from your TV set to your DVD recorder

using 'Easy Link'.

Please see your TV's operating instructions.

Tip

Have the following cables ready:

an aerial cable (1, supplied), a mains cable (2, supplied), a special scart cable (3, suitable for

Easylink).

ANTENNA IN socket at the back of the DVD recorder.

1 Switch off your TV set.

2 Remove the aerial cable plug from your TV set. Insert it into the

the back of the DVD recorder and the other end into the aerial input

socket at the back of the TV set.

3 Insert one end of the supplied aerial cable into the TV OUT socket at

TO TV-I/O at the back of the DVD recorder and the corresponding

scart socket at the back of the TV set (see TV set operating

4 Plug in a special scart cable (for Easylink) into the scart socket EXT 1

instructions).

Preparing the remote control for

Connecting the DVD recorder

operation

The remote control and its batteries are packed separately in the original DVD recorder

packaging. You must install the batteries in the remote control before use - described in the

following section.

1 Take the remote control and the enclosed batteries (2 batteries).

2 Open the battery compartment, insert the batteries as shown and

then close the battery compartment.

The remote control is now ready to use.

Its range is approximately 5 to 10 meters.

'Aim' correctly

In the following sections, you will need the remote control for the first time.

Aim the remote control at the DVD recorder and not at the TV set.

Connecting your DVD recorder to the TV

set

The necessary cable connections must be made before you can record or playback TV

programmes using your DVD recorder.

Connect the DVD recorder directly to your TV set. If there is a video recorder in between

the picture quality may be poor.

We recommend that you use a scart cable to connect your TV set and DVD recorder.

What is a scart cable?

The scart or Euro AV cable serves as the universal connector for picture,

sound and control signals. With this type of connection, there is practically no

loss of quality in picture or sound transmission.

Connecting the DVD recorder

EN 12 DVDR70 & DVDR75/0x13.

Connecting with a scart cable without

'Easy Link'

Have the following cables ready:

Directions For Use

Connecting the DVD recorder

My TV set has several scart sockets. Which one should I use?

Select the scart socket that is suitable for both video output and for video

input.

My TV set shows me a selection menu for the scart socket

ANTENNA IN socket at the back of the DVD recorder.

an aerial cable (1, supplied), a mains cable (2, supplied), a scart cable (3).

1 Remove the aerial cable plug from your TV set. Insert it into the

the back of the DVD recorder and the other end into the aerial input

socket at the back of the TV set.

2 Insert one end of the supplied aerial cable into the TV OUT socket at

back of the DVD recorder and the scart socket for the DVD

3 Plug a scart cable into the scart socket EXT 1 TO TV-I/O at the

recorder at the back of the TV set (see TV set operating instructions).

Select 'VCR' as tje source for this scart socket.

4MAINS at the back of the DVD recorder and the other end into

the wall socket.

The most important features of the DVD recorder will appear in

scrolling text on the display. After the first installation is completed

4 Switch on the TV set.

5 Insert one end of the supplied mains cable into the mains socket

this function will be switched off. How you switch on this function

again, read in the chapter 'User preferences' in the section 'standby'.

6 Switch on the DVD recorder using STANDBY/ON m .'IS TV ON?'

will appear on the display.

switched to the programme number for the scart socket, e.g. 'EXT',

'0', 'AV', you will see the following picture:

7 If the connection was properly made and your TV was automatically

ENGLISH

Problem

below the picture)

off

remote control.3Select the next line with CH+ A or CH- B .4Check if the displayed settings for 'Year', 'Month' and 'Date' are

correct.

When all information is correct, save by pressing OK .

I can see more installation menus on my TV set

Not all the necessary data has been transferred. Please enter the settings

Check if the time in 'Time' is correct.2If required, change the time with the number buttons 0..9 on your

Normally the date and time are taken from the data sent by the TV

channel stored on programme P01. If th aerial signal is too weak or there

is excessive interference, you should set the date and time manually:

a'Time', 'Year', 'Month', 'Date' appears on the TV screen

4MAINS at the back of the DVD recorder and the other end into

the wall socket.

5 Switch on the TV set.

6 Insert one end of the supplied mains cable into the mains socket

7 A message appears on the screen announcing that the transfer has

started. 'EASYLINK' appears on the display during transfer.

The TV set transfers all saved TV channels, in the same order, to the

DVD recorder.

This may take several minutes.

by hand as follows. For more information on the various functions see

'Initial installation' in 'Installing your DVD recorder'.

with OK .

Select the desired audio language using CH- B or CH+ A and confirm

confirm with OK .

Select the desired subtitle language with CH- B or CH+ A and

Select the desired screen format position using CH- B or CH+ A .

'4:3 letterbox' For a 4:3 TV set; cinema format (black bars above and

'4:3 panscan' For a 4:3 TV set; full height format with the sides cut

Problem

Confirm with OK .5Select the country of your residence with CH- B or CH+ A .

If your country does not appear, select 'Other'.6Confirm with OK .

'16:9' For a 16:9 TV set

Initial installation is now complete.

EasyLink

loading data from TV;

please wait

Virgin mode

English

Audio Language

Español

Français

English

Italiano

Press OK to continue

Connecting the DVD recorder

Directions For Use

EN 13DVDR70 & DVDR75/0x1 3.

Connecting the DVD recorder

Cinch socket OUT L AUDIO R at the back of the DVD recorder

and the other end into the audio input socket (usually red/white) on

4 Insert one end of the supplied audio (Cinch) cable into the red/white

the TV set (usually labelled 'Audio in' or 'AV in'. See TV operating

instructions).

5 Switch on the TV set. Switch the TV set over to the SVHS input

socket or select the relevant programme number. Please see your

TV's operating instructions for the programme number you need.

4MAINS at the back of the DVD recorder and the other end into

the wall socket.

6 Insert one end of the supplied mains cable into the mains socket

ENGLISH

Problem

The most important features of the DVD recorder will appear in

scrolling text on the display. After the first installation is completed

this function will be switched off. How you switch on this function

again, read in the chapter 'User preferences' in the section 'standby'.

7 Switch on the DVD recorder using STANDBY/ON m . IS TV ON?'

will appear on the display.

Then, read the paragraph on 'Initial installation' in 'Installing your DVD recorder'.

Connecting with video(CVBS) cable

This cable, usually with yellow Cinch connectors, is used for transmitting the Composite Video

signal (FBAS, CVBS). In this method of transmission the colour signal and the brightness signal

are transmitted on the same cable. In certain circumstances, this can lead to problems with the

picturem, such as 'Moiré' patterns.

Have the following cables ready:

an aerial cable (1, supplied), a mains cable (2, supplied), a video (CVBS)cable (3, supplied, yellow

plug), an audio cable (4, supplied, red/white plug).

ANTENNA IN socket at the back of the DVD recorder.

1 Remove the aerial cable plug from your TV set. Insert it into the

the back of the DVD recorder and the other end into the aerial input

socket at the back of the TV set.

2 Insert one end of the supplied aerial cable into the TV OUT socket at

Virgin mode

aMy screen is empty.

b Many TV sets are switched by the DVD recorder to the programme

Menu Language

number for the scart socket by way of a control signal sent through the

English

scart cable.

b If the TV set does not automatically switch to the scart socket programme

Español

Français

number, manually change to the corresponding programme number on your

TV set (see your TV's operating instructions).

Italiano

Deutsch

Press OK to continue

TO TV-I/O socket on the DVD recorder. The EXT 2 AUX-I/O socket is

intended only for additional devices.

b Check that the scart cable is connected from the TV set to the EXT 1

Connecting with an SVideo(Y/C)cable

Then, read the paragraph on 'Initial installation' in 'Installing your DVD recorder'.

This connecting cable, also known as the SVHS cable, is used to transmit the brightness signal (Y

signal) and colour signal (C signal) separately. This mini DIN socket/plug is also called a Hosiden

socket/plug.

Have the following cables ready:

an aerial cable (1, supplied), a mains cable (2, supplied), an S-Video(SVHS) cable (3), an audio

cable (4, supplied, red/white plug).

ANTENNA IN socket at the back of the DVD recorder.

1 Remove the aerial cable plug from your TV set. Insert it into the

the back of the DVD recorder and the other end into the aerial input

socket at the back of the TV set.

2 Insert one end of the supplied aerial cable into the TV OUT socket at

(Y/C) socket at the back of the DVD recorder and the other end into

the S-Video (SVHS) input socket on the TV set (usually labelled

3 Insert one end of an S-Video(SVHS) cable into the OUT S-VIDEO

'S-Video in' or 'SVHS in'. See TV operating instructions).

Connecting the DVD recorder

EN 14 DVDR70 & DVDR75/0x13.

Connecting additional devices to the

second scart socket

You can connect additional devices such as decoders, satellite receivers, camcorders, etc. to the

EXT 2 AUX-I/O socket. When playback is started on this additional device the DVD recorder

automatically connects the EXT 2 AUX-I/O scart socket with the EXT 1 TO TV-I/O scart

Directions For Use

Problem

Connecting additional devices

shows 'NO SIGNAL'

video recorder.

this signal is poor or does not comply with relevant standards.aWhen I copy DVD video discs or prerecorded video cassettes the

picture is fuzzy and the brightness varies

copy-protected. Even though the picture on the TV is fine the recording on

a DVD+R(W) is faulty. This interference is unavoidable with copy-protected

aWhen copying video cassettes the display on the DVD recorder

b Check that the cable is plugged in firmly.

b If a recording is made from a video recorder, change the tracking on the

b The DVD recorder may not be able to recognise the video input signal if

EXT 2 AUX-I/O scart socket and playback from the DVD recorder.

socket. You will then see the picture from the additional device on your TV set, even if the

DVD recorder is switched off.

The TV/DVD button on the remote control allows you to switch between playback through the

Connecting additional video recorders

You can connect a video recorder to the EXT 2 AUX-I/O socket.

If you have an SVHS video recorder you can also use the OUT S-VIDEO (Y/C) socket and the

OUT L AUDIO R sockets.

Please note:

Most prerecorded video cassettes and DVDs are copy-protected. If you try to copy them you

will see the message 'COPY PROT' on the DVD recorder's display.

b This happens if you try to copy DVDs or video cassettes that have been

DVDs or video cassettes.

Connecting additional devices

Cinch socket OUT VIDEO (CVBS) at the back of the DVD

3 Insert one end of the supplied video (CVBS) cable into the yellow

recorder and the other end into the video input socket (usually

yellow) on the TV set (usually labelled 'Video in' or 'AV in'. See TV

operating instructions).

Cinch socket OUT L AUDIO R at the back of the DVD recorder

4 Insert one end of the supplied audio (Cinch) cable into the red/white

and the other end into the audio input socket (usually red/white) on

the TV set (usually labelled 'Audio in' or 'AV in'. See TV operating

ENGLISH

instructions).

input socket or select the relevant programme number. Please see

5 Switch on the TV set. Switch the TV set over to the Video/Audio

your TV's operating instructions for the programme number you need.

4MAINS at the back of the DVD recorder and the other end into

6 Insert one end of the supplied mains cable into the mains socket

the wall socket.

The most important features of the DVD recorder will appear in

scrolling text on the display. After the first installation is completed

this function will be switched off. How you switch on this function

again, read in the chapter 'User preferences' in the section 'standby'.

7 Switch on the DVD recorder using STANDBY/ON m .'IS TV ON?'

will appear on the display.

Then, read the paragraph on 'Initial installation' in 'Installing your DVD recorder'.

Connecting the DVD recorder

Connecting audio devices to the digital

audio socket

At the back of the DVD recorder there is a digital audio output socket DIGITAL AUDIO

OUT for an coaxial cable.

These can be used to connect the following:

•) an A/V receiver or an A/V amplifier with a digital multichannel sound decoder

•) a receiver with twochannel digital stereo (PCM)

Directions For Use

Digital multichannel sound

Digital multi-channel sound offers the best possible sound quality. You will

need a multi-channel A/V receiver or amplifier that supports at least one of

the audio formats of the DVD recorder (MPEG2, Dolby Digital and DTS).

Consult the operating instructions for your receiver to find out which audio

formats it supports.

aAll I can hear from my loudspeakers is a loud distorted noise

b The receiver is not compatible with the digital audio format of the DVD

recorder. The audio format of the DVD disc is displayed in the status

window when you switch to anoter language. Playback in six-channel digital

Problem

surround sound is only possible if the receiver has a digital multi-channel

sound decoder.

EN 15DVDR70 & DVDR75/0x1 3.

Connecting additional devices

Connect camcorder to the front sockets

To copy camcorder recordings, you can use the front sockets. These sockets are located behind

the flap on the left hand side.

Best picture quality

If you have a DV or Digital 8 camcorder, connect the DV IN input of the DVD recorder to the

ENGLISH

' function (Subtitle).

appropriate DV output on the camcorder.

When films are transferred the original recording date and time are stored as DVD subtitles.

On playback, this data can be displayed on the TV screen by using the '

Very good picture quality

If you have a Hi8 or S-VHS(C) camcorder, connect the S-VIDEO input of the DVD recorder to

the appropriate S-VHS output on the camcorder.

You must also connect the audio input left AUDIO right on the DVD recorder to the audio

output on the camcorder.

Good picture quality

If you have a camcorder that only has a single video output (Composite Video, CVBS), connect

the VIDEO input on the DVD recorder to the appropriate output on the camcorder.

You must also connect the audio input left AUDIO right on the DVD recorder to the audio

output on the camcorder.

Connecting audio devices to the analogue

audio sockets

Two audio output sockets OUT L AUDIO R are located on the back of the DVD recorder

(audio signal output left/right)

These can be used to connect the following:

•) a receiver with Dolby Surround Pro Logic

•) a receiver with twochannel analogue stereo

Can I use the 'Phono' input on my amplifier?

This socket (input) on the amplifier is designed only for record players

without preamplifiers. Do not use this input for connecting the DVD

recorder.

The DVD recorder or the amplifier may be damaged as a result.

Connecting additional devices

EN 16 DVDR70 & DVDR75/0x13.

Directions For Use

7 Select the desired screen format position using CH- B or CH+ A .

Virgin mode

These settings will only be used if you insert a DVD that contains this

information.

TV Shape

Which screen formats can I select?

4:3 letterbox

4:3 panscan

Problem

Installing your DVD recorder

the top and bottom.

The DVD recorder cannot find any TV stations

TV set?

If not, check the cable connection from the aerial (aerial socket) to the

DVD recorder and to the TV set.

The DVD recorder searches the entire frequency range in order to find

and save the largest possible number of TV channels.

to the end and then, if you wish, start the automatic search (see 'Automatic

Please wait

b If you have not connected an aerial, go through all the basic settings right

TV station search').

complete' will appear on the TV screen.

B When the automatic TV channel search is complete, 'Autom. search

'Time', 'Year', 'Month', 'Date' will then appear on the TV screen.

C Check if the time in 'Time' is correct.

Autom. search

À If required, change the time with the number buttons 0..9 on your

Autom. search complete

remote control.

00 Channels found

Á Select the next line with CH+ A or CH- B .

Time 20:01

Year 2003

To continue

Press OK

Month 01

Date 01

'4:3 letterbox' for a 'wide-screen' (cinema format) picture with black bars at

'4:3 panscan' for a full-height picture with the sides trimmed.

'16:9' for a wide-screen TV set (screen edge ratio 16:9)

8 Confirm with OK .

16:9

Press OK to continue

Why do I have to select a country?

To call up the specific settings for the respective country, you must first install

Austria

Country

the country.

Belgium

Denmark

Finland

France

Press OK to continue

the DVD recorder, press OK .

0 Confirm with OK .

A After you connect the aerial (or cable TV, satellite receiver, etc.) to

If your country does not appear, select 'Other'.

9 Select the country of your residence with CH- B or CH+ A .

Virgin mode

The automatic TV channel search starts. 'WAIT' will appear on the

display.

b Select channel 1 on the TV set. Can you see the stored TV channel on the

Autom. search

Installation

Searching for TV channels

00 Channels found

b Please have patience.

Initial installation

Installing your DVD recorder

After successfully connecting your DVD recorder to the TV set and other additional devices as

described in the previous chapters, this chapter will show you how to start the initial installation.

The DVD recorder automatically seeks out and stores all available TV channels.

Connecting additional devices

If you have connected additional devices such as a satellite receiver to the

ENGLISH

aerial cable, switch them on. The automatic channel search will recognise it

and save it.

No aerial connected

Even if you only want to use the DVD recorder to play back or have only

Tip

connected a satellite receiver, you must still complete the initial installation.

This is necessary so that the basic settings are stored correctly. Once initial

installation is complete you can use the DVD recorder as normal.

CH- B or CH+ A .

1 Select the desired language for the on-screen menu by pressing

Virgin mode

What is an onscreen menu?

English

Menu Language

The multi-language on-screen menu takes the mystery out of using your new

Español

Français

DVD recorder. All settings and/or functions are displayed on your TV screen

Italiano

in the relevant language.

Deutsch

Press OK to continue

What is an audio language?

The DVD will play the sound in the language you select, provided this

language is available on the disc. If it is not available on the disc the fist

language on the DVD will be used instead. The DVD Video Disc menu, if

available, will also be displayed in the language you select.

2 Confirm with OK .

3 Select the desired audio language using CH- B or CH+ A .

Virgin mode

English

Español

Français

English

Audio Language

Italiano

Press OK to continue

CH+ A .

4 Confirm with OK .

5 Select the desired language for the subtitles by pressing CH- B or

Virgin mode

What is the subtitle language?

English

Subtitle Language

The subtitles will be displayed in the language you select, provided this

Español

Français

language is available on the disc. If it is not available on the disc the fist

language on the DVD will be used instead.

English

Italiano

6 Confirm with OK .

Press OK to continue

Installing your DVD recorder

Directions For Use

EN 17DVDR70 & DVDR75/0x1 3.

Allocating a decoder

Some TV channels send coded TV signals that can only be viewed properly with a purchased or

rented decoder. You can connect such a decoder (descrambler) to your DVD recorder. The

following function automatically activates the connected decoder for the TV channel you want to

watch.

How do I allocate the decoder for Easy Link?

Installing your DVD recorder

' symbol with D or C .

If your TC=V set supports 'Easy Link' the decoder must be assigned to the

relevant TV channel on the TV set (see the operating instructions for your TV

set). Settings cannot then be made in this menu.

the DVD recorder.

1 Switch on the TV set. If required, select the programme number for

0..9 on the remote control to select the TV channel for which you

want to use the decoder. If necessary, use the MONITOR button to

switch to the internal tuner.

bar appears.

3 Use the CH+ A and CH- B buttons or the number buttons

2 Switch on the DVD recorder using STANDBY/ON m .

4 Press the SYSTEM-MENU button on the remote control. The menu

5 Select '

C .

6 Select 'Installation' using CH- B or CH+ A and confirm with C .

7 Select 'Manual search' using CH- B or CH+ A and confirm with

8 Select 'Decoder' using CH- B or CH+ A .

Installation

Manual search

How do I switch the decoder off again?

Use C to select 'Off'inthe'Decoder' line on the screen (Decoder off).

9 Select 'On' with D or C .

Channel/freq. CH

Entry/search 01

0 Confirm with OK .

A To end, press SYSTEM-MENU .

Your decoder has now been allocated to this TV channel.

To store

Press OK

Programme number 01

TV channel name BBC1

Decoder Off

TV system PAL-BG

NICAM On

Fine tuning 0

Â Check if the displayed settings for 'Year', 'Month' and 'Date' are

correct.

ENGLISH

Tip

Satellite receiver

If you are connecting a satellite receiver, please read the section on 'Using a

satellite receiver'.

Decoder

If you are connecting a decoder, you must install it as described in the next

section.

Ã When all information is correct, save by pressing OK .

The initial installation is now complete.

sound at all, the wrong TV system may have been stored for the TV

aSound may be distorted on some TV channels.

b If the sound is distorted on any of the stored TV channels or if there is no

Problem

channel. Read 'Manual TV channel search' for information on how to

change the TV system.

Using a satellite receiver

TV channels from a satellite receiver (connected to scart socket EXT 2 AUX-I/O ) are received

on the DVD recorder on programme number 'EXT2'

If necessary, use the MONITOR button to switch to the internal tuner.

Select programme number 'EXT1' with 0 on the remote control and then select programme

number 'EXT2' with CH- B .

You should select the TV channels to be received by the satellite receiver directly on the

receiver itself.

Installing your DVD recorder

EN 18 DVDR70 & DVDR75/0x13.

Directions For Use

In 'TV channel name', press C .2Select the desired symbol position using D or C .3Change the symbol at the symbol position with CH- B or CH+ A .4Select the next symbol position in the same way.5Keep pressing C until the cursor disappears.

How can I change the symbol of a TV channel?

Tip

How can I change the TV system of the TV channel?

In 'TV system', use D or C to select the TV system that produces the

least distortion of picture and sound.

What is NICAM?

NICAM is a digital sound transmission system. Using NICAM, you can

Tip

Installing your DVD recorder

transmit either 1 stereo channel or 2 separate mono channels. However, if

reception is poor and the sound distorted you can turn off NICAM.

In 'NICAM', select 'Off' using D or C .

How can I improve the automatic process for storing channels?

To change the automatic process for storing channels (fine tuning), select

'Fine tuning'.

Using D or C you can try to fine-tune the TV channelmanually.

0 Press OK to store the TV channel.

Sorting TV channels automatically

B To end, press SYSTEM-MENU .

A To search for other TV channels, begin again at

(Follow TV)

When the automatic channel search function is activated, the TV channels are stored in a specific

order. This may differ from the order in which the TV channels appear on your TV set.

This function changes the order of the TV channels stored in your DVD recorder to match the

order on the TV set.

This only works if the DVD recorder ( EXT 1 TO TV-I/O socket) and the TV set are

connected with a scart cable.

What does EasyLink do?

If your TV set supports 'Easylink,..', TV channels will be stored during initial

installation in the same order as they appear on the TV set. To store the TV

channels in a different order, you'll need to change the order on the TV set.

When you start the Follow TV function the information is transferred again

from the TV set.

the DVD recorder.

1 Switch on the TV set. If required, select the programme number for

Manual TV channel search

In some cases, not all of the available TV channels may have been found and stored during initial

installation. In this case, you will need to search for and store the missing or coded TV channels

manually.

ENGLISH

Manual search with EasyLink

With 'Easy Link', the DVD recorder will automatically download the TV

channels stored on the TV set. This is why some lines have no function. To

store new TV channels, they must first be stored on the TV set. The

Tip

information will then be transferred to the DVD recorder automatically.

1 Switch on the TV set. If required, select the programme number for

the DVD recorder.

2 Switch on the DVD recorder using STANDBY/ON m .

3 Press SYSTEM-MENU on the remote control. The menu bar

appears.

Problem

' symbol with D or C .

C .

'Freq.'(Frequency), 'CH'(Channel), 'S-CH'(Special/hyperband channel)

using the number buttons 0..9 .

4 Select '

5 Select 'Installation' using CH- B or CH+ A and confirm with C .

6 Select 'Manual search' using CH- B or CH+ A and confirm with

7 In 'Channel/freq.', select the desired display using C .

Manual search

Installation

8 In 'Entry/search', enter the frequency or channel of the TV station

Channel/freq. CH

Entry/search 01

Programme number 01

TV channel name BBC1

Decoder Off

aI don't know the channel for my TV station

TV system PAL-BG

NICAM On

number/frequency number will appear on the TV screen.

b In this case, press C to start the automatic search. A changing channel

To store

Fine tuning 0

Continue the automatic search until you have found the TV channel you

are looking for.

number you want to use for the TV channel, e.g. '01'.

9 Using D or C in 'Programme number', select the programme

Press OK

Installing your DVD recorder

Directions For Use

EN 19DVDR70 & DVDR75/0x1 3.

Installing your DVD recorder

' symbol with D or C .

What does Easy Link do?

With Easylink, you can search for and store TV channels only on the TV set.

These settings are accepted by the DVD recorder. Use this function to start

the transfer of TV channels from the TV set.

the DVD recorder.

appears.

recorder to save all available TV channels. This procedure may take

several minutes.

complete' will appear on the TV screen.

Automatic TV channel search

During installation, all available TV channels are searched for and stored. If the channel

' symbol with D or C .

bar appears.

assignments of your cable or satellite TV provider change or if you are reinstalling the DVD

recorder, e.g. after moving house, you can start this procedure again. This will replace the stored

TV channels with the new ones.

the C button.

ENGLISH

the DVD recorder display.

aI cannot switch my TV set to programme number '1'

please disconnect these devices. Other connected devices may have

b If you have connected additional devices to the EXT 2 AUX-I/O socket,

1 Switch on the TV set. If required, select the programme number for

Problem

switched the TV set to the programme number of the scart socket.

2 Switch on the DVD recorder using STANDBY/ON m .

'WAIT' will appear in the display. The DVD recorder compares the TV

3 Press SYSTEM-MENU on the remote control. The menu bar

channels on the TV set and the DVD recorder.

If the DVD recorder finds the same TV channel as on the TV set it

stores it at 'P01'.

4 Select '

5 Select 'Installation' using CH- B or CH+ A and confirm with C .

6 Select 'Autom. search' using CH- B or CH+ A .

7 Press C .

8 The automatic TV channel search starts. This allows the DVD

9 When all the TV channels have been found, 'Autom. search

Autom. search

Installation

Searching for TV channels

00 Channels found

0 To end, press SYSTEM-MENU .

Please wait

You can read about how to search for a TV channel manually in 'Manual TV channel search'.

Problem

receiving a video signal from the TV set.

for video signals.

b Chech the connectors at both ends of the scart cable.

b Check your TV's operating instructions to see which scart socket is used

b If the problem persists, you won't be able to use this feature.

Please read 'Adding and clearing TV channels manually'.

a'NOTV' will appear in the display. The DVD recorder is not

Tip

Deleting sorting

You can delete incorrect TV channel sorting by pressing D .

until you have assigned all the TV channels.

3 Press the SYSTEM-MENU button on the remote control. The menu

2 Switch on the DVD recorder using STANDBY/ON m .

5 Select 'Installation' using CH- B or CH+ A and confirm with C .

4 Select '

6 Select line 'Follow TV' with CH- B or CH+ A . and confirm with

7 Confirm the message on the screen with OK .'TV 01' will appear in

8 Select programme number '1' on the TV set.

TV 01

9 Confirm with OK on the DVD recorder remote control.

0 Wait until for example 'TV 02' appears in the display.

A Select the next programme number on the TV set, e.g. '2'.

B Confirm with OK on the DVD recorder remote control.

TV 02

C Repeat steps

À To end, press SYSTEM-MENU .

Installing your DVD recorder

EN 20 DVDR70 & DVDR75/0x13.

the DVD recorder.

Directions For Use

' symbol with D or C .

appears.

the C button.

Which settings can I choose?

'Audio Language' : Playback language (audio language)

'Recording audio' : Type of audio recording 'Language 1'or'Language2''Subtitle' : Subtitle language

'Menu': Language of the OSD menu

Tip

'Country' : Location (country)

Installing your DVD recorder

with OK .

Setting the language/country

You can select the country and, for DVD playback, the language for the subtitles and the audio

language. Please note that with some DVDs the audio language and/or subtitle language can be

changed only via the DVD menu.

For bilingual shows you can also select the sound channel of the TV station for recording.

You also have the option of setting one of the displayed languages for the on-screen menu

(OSD). However, the DVD recorder display will only display English text regardless of this

setting.

1 Switch on the TV set. If required, select the programme number for

ENGLISH

EasyLink

With Easylink, you can search for and store TV channels only on the TV set.

2 Switch on the DVD recorder using STANDBY/ON m .

These settings are then accepted by the DVD recorder.

That is why you cannot select this function manually.

3 Press SYSTEM-MENU on the remote control. The menu bar

The teletext clock resets automatically

If you store a TV channel which transmits TXT/PDC on programme number

'P01', the date and time will automatically be transmitted and constantly

updated. As a result, the changes from summer time to winter time and back

5 Select line 'Language' with CH- B or CH+ A . and confirm with

4 Select '

Tip

again will be made automatically.

6 Select the appropriate line and confirm with C .

the DVD recorder.

Language

the remote control. The menu bar appears.

Audio Language English

' symbol with D or C .

7 Select the appropriate setting using CH- B or CH+ A and confirm

8 To end, press SYSTEM-MENU .

Switching over audio recording

(2channel sound)

Some TV programmes transmit an extra audio signal in stereo in addition to the normal audio

signal (2-channel sound). In most cases this means that an additional language is available. If a TV

programme is available in, say, English and German, German may be available as the second

language.

To record TV programmes in stereo or 2-channel sound you can select Stereo or the language

you want as the default setting. This setting does not become active until the sound of a TV

programme is transmitted in 2-channel sound.

When you play back the recording you can play back the sound only in the language you used

for the recording.

Recording audio Language 1

Subtitle English

Menu English

Country Other

Tip

until you have resorted/deleted all the TV

CLEAR . Proceed at step 6 .

Deleting TV channels

with C .

delete or whose order you want to change.

Unwanted channels or those with poor reception can be deleted using

position and press the D button. The DVD recorder will insert the

TV channel.

channels you want.

Adding and clearing TV channels manually

After you have performed the automatic channel search you may not agree with the sequence in

which the individual TV channels have been allocated to the programme positions (programme

numbers). You can use this function to rearrange the TV channels already stored or to delete

TV channels you don't want or those with poor reception.

4 Select 'Installation' using CH- B or CH+ A and confirm with C .

1 Switch on the TV set. If required, select the programme number for

2 Switch on the DVD recorder. Press the SYSTEM-MENU button on

5 Select 'Sort TV channels' using CH- B or CH+ A and confirm

6 Using CH- B or CH+ A select the TV channel that you want to

...

Sort TV channels

Installation

7 Confirm with C .

• P01 BBC1

P02 BBC2

To exit press

SYSTEM MENU

P03 ITV

P04

P05

P06

...

To sort

Press ›

3 Select '

8 Using CH- B or CH+ A , shift the TV channel to the desired

9 Repeat steps

0 To store, press OK .

A To end, press SYSTEM-MENU .

Installing your DVD recorder

Directions For Use

User preferences

Title/trackCChapter/index

Audio languageESubtitle languageFCamera angleGZoom

EN 21DVDR70 & DVDR75/0x1 3.

On-screen information

SoundIFrame advanceJSlow motionKFast forwardLSearch by time

system menu bar. The menu bar cannot be displayed during recording.

Symbols in the menu bar

You can check or change many of the functions and settings of your DVD recorder via the

Onscreen information

Press SYSTEM-MENU to open and close the menu bar (main menu). Use D and C to select

the relevant function. Use CH- B to confirm the function and go either to another menu or

execute the function directly.

Some functions may not be available, depending on the disc inserted.

ENGLISH

Menu bar 1

Menu bar 2

While menu bar 1 is being displayed you can go to menu bar 2 by pressing C again.

the DVD recorder.

1 Switch on the TV set. If required, select the programme number for

' symbol with D or C .

6 Select line 'Recording audio' and confirm with C .

Language

Audio Language English

7 Select 'Language 1'or'Language 2' with CH- B or CH+ A and

Recording audio Language 1

confirm with OK .

Subtitle English

Menu English

Country Other

8 To end, press SYSTEM-MENU .

Setting the time and date

If the display shows an incorrect time or '--:--', the time and date must be reset manually.

If a TV channel which transmits TXT/PDC (teletext/PDC) is stored under programme number

'P01', the time and date will automatically be taken from the TXT/PDC information.

appears.

3 Press SYSTEM-MENU on the remote control. The menu bar

2 Switch on the DVD recorder using STANDBY/ON m .

the C button.

4 Select '

5 Select line 'Language' with CH- B or CH+ A . and confirm with

1 Press SYSTEM-MENU on the remote control. The menu bar

appears.

' symbol with D or C .

'Stored' will appear briefly on the screen.

the fields, use CH- B or CH+ A .

with the number buttons 0..9 on your remote control.

7 Check the displayed settings and confirm with OK .

3 Select 'Installation' using CH- B or CH+ A and confirm with C .

4 Select 'Time/Date' using CH- B or CH+ A and confirm with C .

2 Select '

5 Check if the time in 'Time' is correct. If required, change the time

Time/Date

Installation

6 Check 'Year', 'Month' and 'Date' in the same way. To move between

Time 20:00

Year 2003

Month 01

8 To end, press SYSTEM-MENU .

To exit press

SYSTEM MENU

Date 01

Installing your DVD recorder

EN 22 DVDR70 & DVDR75/0x13.

Directions For Use

On-screen information

RecordingSStopTPlaybackUPlaybackPause

Operating mode symbols

RecordPause

Search forwards (8x speed)YSearch backwards (8x speed)ZSlow motion

ENGLISH

Tuner information box

This field is located in the bottom left-hand corner of the screen. The aerial signal, the TV

channel and the TV channel name for the selected programme are displayed.

Current channel/selected input socketbNo signal

The TV channel is not available/the additional device is not connected or

it is switched offcCopyprotected signal

Timer information box

This box appears above the tuner information box. When a timer recording is set, it shows the

timer icon and the start time or date of the first programme to be recorded.

If no timer recording is scheduled, the current time is displayed.

This box disappears during playback of a disc or after a recording starts.

Timer starts on the day showngOTR recording runs until the stop time displayedhCurrent time

No timer event programmed

Field for temporary messages

The top left corner of the menu line contains a field for temporary messages relating to the

various operating modes. This information appears briefly on the screen when certain disc

functions have been activated:

ShuffleScanRepeat entire discRepeat titleRepeat trackRepeat chapterRepeat from A to the endRepeat from A to BCamera angleChild lock enabledResume playbackIllegal action



Status field

The status field shows the current operating mode (status) of the DVD recorder and the type of

disc inserted. This display can be disabled.

DVD+RWWDVD+RNDVDVideo

Disc type symbols

VideoCDPNo discQError

On-screen information

Directions For Use

EN 23DVDR70 & DVDR75/0x1 3.

Opening/closing the tray using the remote control

You can open and close the disc tray using the remote control.

Press and hold the STOP h button on the remote control until the dialog

Tip

box shows 'OPENING'or 'CLOSING'.

3 Playback starts automatically.

A menu may appear when a DVD is played back. If the titles and chapters are numbered, press a

playback

This will appear on the display:

title, chapter, elapsed time.

Playing a DVD video disc

1 If playback does not start automatically, press PLAY G .

CH- B buttons or number buttons 0..9 to select a menu item and confirm with OK .

number button on the remote control. You can also use the D , C , CH+ A ,

You can also access the menu using DISC-MENU on the remote control.

For further information see 'Playing a DVD video disc'.

O select the title you want to play back.

When a DVD+RW is played back the index overview appears. Using CH- B , CH+ A , N ,

Confirm with OK .

For further information see 'Playing back a DVD+RW/+R Disc'.

If playback does not start automatically, press PLAY G .

For further information see ' Playing an audio CD'.

If the 'h' symbol appears in the display, start playback by pressing PLAY G .

If a menu appears on the screen, use the remote control buttons indicated on the screen to select

the menu option you want (PREV= N , NEXT= O ) or with the number buttons 0..9 .

For further information see ' Playing a (Super) Video CD'.

2 To stop playback, press STOP h on the remote control or h on

the DVD recorder.

recorder.

3 To eject the disc, press OPEN/CLOSE J on the front of the DVD

C01 2:04

General notes on playback

playback

With this DVD recorder you can play back the following systems:

•) DVD Video

•) (Super)Video CD Disc

•) DVD+RW Disc

•) DVD+R Disc

•) DVD-RW (video mode, finalised)

•) DVD-R

ENGLISH

•) CD-R

•) CD-RW

•) Audio CD

•) MP3 CD

You can operate the video recorder using the remote control or the buttons on the front of the

DVD recorder.

aThe display will read 'PIN'

on 'Child lock' and 'Releasing a disc' in the chapter on 'Access control

b The child lock has been activated for the inserted disc. Read the sections

(child lock).aThe menu on the screen is showing an 'X'

before the disc can be played, or so that only limited operation is possible

b Some DVD discs can be manufactured so that certain steps are required

during playback. When an 'X' appears on the screen the selected feature is

not possible.aThe screen is showing regional code information

b Since DVD films are not normally released in all parts of the world at the

same time, all DVD players have a specific regional code. Discs can be given

a regional code. If the regional codes differ between the player and the

disc, playback is not possible.

b The regional code is shown on the label on the back of the machine.

Problem

b The regional code does not apply to recordable DVD discs.

Inserting a disc

How do I insert a doublesided DVD?

Double-sided discs do not have labelling over the whole surface. The labelling

for each side is in the centre of the disc. To play a side its label must be

PLAY G or OPEN/CLOSE J .'CLOSING' and then 'READING' will

open. While the disc tray is opening, 'OPENING' and then 'TRAY OPEN'

when the tray is fully open.

appear in the display. The information on the disc will be read.

1 Press the OPEN/CLOSE J button on the front. The disc tray will

2 Carefully place the disc in the tray with the label facing up and press

facing up.

OPENING P01

playback

EN 24 DVDR70 & DVDR75/0x13.

Directions For Use

Playing an MP3 CD

MP3 (MPEG1 Audio Layer-3) files are highly compressed music files. Using this technology the

data volume can be compressed by a factor of 10. This means it is possible to record 10 hours

of music in CD quality on a single CD-ROM.

When creating MP3 CDs please note the following:

File system: ISO9660

Directory structure: maximum of 8 levels

Formats: *.mp3

Filenames: maximum of 12 characters (8+3)

Maximum of 32 albums, 999 titles

Supported sampling frequencies: 32, 44.1, 48 (kHz). Music with sampling frequencies other than

these will be skipped.

Supported bit rates: 32, 64, 96, 128, 192, 256 (kbit/s)

Tip

show on the TV screen and on the display.

Further information on the album, track and artist will also be displayed if

show on the TV screen and on the recorder display.

During stopped playback ( STOP h button) the numbers of the albums will

included in the ID tag.

2 Stop playback using STOP h . The number of albums is displayed in

the display.

Additional playback features

Using N or O select the next or previous title.

You can also use the T/C button to select titles and albums.

MP3 CD display

If the TV is on, the MP3 CD screen appears automatically.

During playback, the current track number and its elapsed playing time will

Important notes for playback:

Only the first session of a multi-session CD will play back.

1 Insert an MP3 CD. Playback starts automatically.

ID3 Tag: Version 1, 1.1. In later versions the directory name is displayed as the album and the

filename as the title.

Tip

the remote control to select the number of the title/chapter.

Press the T/C button and use the C or D button to select the 'T'

symbol for title or 'C' for chapter.2Use the CH- B or CH+ A buttons or the number buttons 0..9 on

You can also use the repeat functions ( PLAY MODE button).

playback

Playing a DVD+RW/ +R disc

starts automatically.

1 If the disc is write-protected or a finalised DVD+R disc, playback

2 If playback does not start automatically, use the CH- B or

ENGLISH

CH+ A button to select the title you want to play on the index

screen.

You can also use the N or O button on the front.

This will appear on the display:

3 Press the PLAY G button.

title number, recording quality.

Problem

aI can see the message 'EMPTYDISC'

b The disc does not contain any recordings.

the DVD recorder.

4 To stop playback, press STOP h on the remote control or h on

5 To eject the disc, press OPEN/CLOSE J on the front of the DVD

recorder.

What should I note when playing back different recording types

(qualities)?

be selected during playback.

For more information see the section on 'Selecting the recording type

(quality)' in the chapter on 'Manual recording'.

The correct recording quality 'M1, M2, M2x, M3, M4, M6' will automatically

Playing an audio CD

You can also use the DVD recorder to play audio CDs

Audio CD display'

1 Insert an audio CD. Playback starts automatically.

Tip

If the TV is on, the audio CD screen appears automatically.

During playback, the current track number and its elapsed playing time will

show on the TV screen and on the recorder display.

time are displayed.

2 Stop playback using STOP h . The number of tracks and the total

C01 ANNA P01

playback

Directions For Use

EN 25DVDR70 & DVDR75/0x1 3.

Changing to another title/chapter

Additonal playback features

If there is more than one title or chapter on a disc you can change to another title or chapter

as follows. However if there are several chapters within a title, these will be selected. The title

can then still be selected via the menu bar.

1 During playback, press O to go to the next title/chapter. Press

N to return to the start of the current title/chapter. Press

N twice to return to the start of the previous title/chapter.

Use the T/C (title/chapter) button

Tip

Problem

Additonal playback features

').

' symbol using C or D and confirm with CH- B .

appropriate title.

Make sure the symbol 'T' (title) is selected in the menu bar.

Press T/C (title/chapter) and then use CH+ A or CH- B to select the

Use T/C to select chapters within a title. Press T/C and use C to

select the 'C' symbol (chapter).

Now select the appropriate chapter with CH+ A or CH- B .

Searching a disc

You can search the disc for a recording at 4x, 8x or 32x playback speed. Other speeds can only

be selected via the menu bar ('

1 During playback, press and hold N (reverse) or O (forwards) to

switch to the search feature. You can switch between the playback

speeds using N / O .

2 To continue playback, press PLAY G twice at your chosen location.

aNo sound

b The sound is switched off in search mode. This is not a fault in your

machine.

During playback press SYSTEM-MENU on the remote control. The

menu bar will appear at the top of the screen.2Select the '

You can now use the D or C button to select different forward and

Search feature via menu bar

backward search speeds.4If necessary, switch the menu bar off with the SYSTEM-MENU button.5To continue playback, press PLAY G twice.

Playing a (Super) Video CD

(Super) Video CDs may be equipped with PBC (Play Back Control). This means that special

playback functions (menus) can be directly selected. The video CD must be PBC compatible (see

CD case).

'PBC' is active in the default settings.

ENGLISH

If the 'h' symbol appears in the display, start playback by pressing

1 Insert a (Super) Video CD.

PLAY G .

indicated on the screen to select the menu option you want

2 If a menu appears on the screen, use the remote control buttons

(PREV= N , NEXT= O ) or with the number buttons 0..9 .

If a PBC menu consists of a list of titles, you can select a title directly.

3 Use RETURN to go back to the previous menu

4 Stop playback using STOP h .

playback

EN 26 DVDR70 & DVDR75/0x13.

should start.

aThe time entered will flash on the screen

b The selected title is shorter than the time entered. Enter a new time or

Problem

cancel the function by pressing SYSTEM-MENU .

Directions For Use

': repeat chapter (DVD only)

': repeat track/title

': repeat entire disc (Video CD, Audio CD only)

': Shuffle









•) '

MODE again you can chose from the following options:

•) Display disappears: no repeat

•) '

You can also keep pressing the PLAY MODE button until the

displays disappear.

You will see a still picture.

' appears on the screen.



The start point is now saved.

' appears on the

Press PLAY G to start playback.



TV screen. Playback now takes place within these points.

You can also keep pressing the PLAY MODE button until the

displays disappear.

Additonal playback features

3 Enter the start time with the digit keys 0..9 from where playback

Repeat/Shuffle play

4 Confirm with OK .

5 Playback starts at the time you entered.

1 Select the desired chapter, title or the entire disc and start playback.

You can mark entire sections or the whole disc for endless playback. Depending on the type of

disc (DVD video, DVD+RW, video CD) you can select a chapter, title or the entire disc.

2 During playback, press PLAY MODE . By pressing PLAY

3 To end the repeat, press the STOP h button.

Repeating a passage (AB)

You can repeat a particular passage within a title/chapter. You need to indicate the start and end

of the passage.

1 During playback press PAUSE 9 at the start point.

3 When the end point is reached press OK .'

2 Keep pressing PLAY MODE until '

4 To end the repeat, press the STOP h button.

ENGLISH

Tip

Still picture

1 During playback, press PAUSE 9 to stop playback and display a still

picture.

C01 2:04

' symbol using C or D and confirm with CH- B .

During a still picture press SYSTEM-MENU on the remote control.

The menu bar will appear at the top of the screen.2Select the '

You can now use the D or C button to go forwards or backwards one

Frame advance via menu bar

frame at a time.4If necessary, switch the menu bar off with the SYSTEM-MENU button.

2 To continue playback, press PLAY G .

down N or O to switch to slow motion.

Slow motion

1 During playback press PAUSE 9 on the remote control. Now hold

2 You can switch between different speeds using N or O .

' symbol using C or D and confirm with CH- B .

During playback press PAUSE 9 and then SYSTEM-MENU on the

remote control. The menu bar will appear at the top of the screen.2Select the '

You can now use the D or C button to select different forward and

Slow motion via menu bar

backward slow motion speeds.4If necessary, switch the menu bar off with the SYSTEM-MENU button.

Search by time

3 To continue playback, press PLAY G twice.

Using this feature you can select where playback should start (select elapsed time).

1 During playback press SYSTEM-MENU on the remote control. The

menu bar will appear at the top of the screen.

' symbol using C or D and confirm with CH- B .

Playback is stopped and a box appears on the screen showing the

elapsed time.

2 Select the '

Additonal playback features

Directions For Use

can also enter the number directly using the number buttons 0..9 .

' icon

EN 27DVDR70 & DVDR75/0x1 3.

Additonal playback features

can also enter the number directly using the number buttons 0..9 .

using C .

You can switch off subtitles again with 0 or by pressing 'off'.

7 To stop the feature, press PLAY G and then SYSTEM-MENU .

Select the audio language

Many pre-recorded DVD discs have more than one audio language. The language initially selected

for playback will be the one you selected when you first set up the DVD recorder. However

you can change the audio language of the inserted disc at any time.

You can change the audio language either using the menu of the inserted disc

1 During playback press AUDIO .

( DISC-MENU button) or the AUDIO button. The audio languages for DVD playback in the

two menus may be different. Please note that with some DVDs the audio language and/or

subtitle language can be changed only via the DVD menu.

2 Select the required audio language using CH- B or CH+ A . You

6 Confirm with OK .

3 Play continues in the new audio language.

Subtitles

Many pre-recorded DVD discs have more than one subtitle language. The language initially

selected for playback will be the one you selected when you first set up the DVD recorder.

However you can change the subtitle language of the inserted disc at any time.

You can change the subtitle language either using the menu of the inserted disc

2 Select the required subtitle language using CH- B or CH+ A . You

1 During playback press SYSTEM-MENU and select the '

( DISC-MENU button) or the menu bar ( SYSTEM-MENU button). The subtitle languages in

the menus may differ.

3 Playback continues in the new subtitle language.

ENGLISH

Problem

' using PLAY



' icon using C .

Scan feature

This feature plays back the first 10 seconds of each chapter (DVD) or track (CD).

' symbol will be hidden

is therefore not available. For more information please read the cover of

your DVD disc.

aThe '

STOP h and then PLAY G .

chapter/index. To start playback at the relevant chapter/index press

MODE .

2 After 10 seconds the DVD recorder switches to the next

1 During playback, press PLAY MODE . Select '

Camera angle

If a DVD contains scenes that have been shot from different camera angles you can select these

camera angles for playback.

1 During playback, press PAUSE 9 . You will see a still picture.

b The selected scene has been shot from only one camera angle. This feature

2 Press SYSTEM-MENU and select the '

' symbol will remain visible until a scene starts for which

image you wish to view.

there is only one camera angle.

also directly enter the number with the number buttons 0..9 .

The '

3 Select the required camera angle with CH- B or CH+ A . You can

4 After a short time, playback will resume from the new camera angle.

Zoom feature

The Zoom feature allows you to enlarge the video image and pan through the enlarged image.

1 During playback, press PAUSE 9 . The DVD recorder switches to

'PAUSE'. You will see a still picture.

2 Press SYSTEM-MENU and select the '

is complete.

4 When 'press OK to pan' appears on the screen, the zoom process

3 Select the required zoom factor using CH- B or CH+ A .

5 Press OK . Using CH+ A , CH- B , C , D select the part of the

Additonal playback features

EN 28 DVDR70 & DVDR75/0x13.

Directions For Use

recorder.

Recording without automatic switchoff

1 Switch on the TV set and select the programme number for the DVD

2 Insert a disc on which the recording is to be made. This disc is then

checked for content and system. READING' will appear on the display.

aIndex display

b A DVD+RW disc has been inserted that already contains recordings. Use

Problem

Tip

Manual recording

S-VIDEO socket has priority.

Switching between the S-VIDEO and VIDEO sockets takes place

automatically. If both sockets are in use, the signal at the

to start.

the CH+ A or CH- B button to select the point where the recording is

The message 'EMPTYDISC' appears in the display

A dialog box appears asking you whether you want to delete the

contents or eject the disc

video-compatible (e.g. a data disc). Recordings on this disc can only be

made if the entire disc is first deleted with the REC/OTR n button.aThe message 'Title limit' appears on the screen if a recording is to

be made

b The disc inserted is a DVD+RW but its contents are not DVD

b The disc inserted is a blank DVD disc.

b A disc may contain a maximum of 48 titles (including blank titles). Delete

titles or change the disc.

switch to the internal tuner in the DVD recorder.

3 If necessary, use the MONITOR button on the remote control to

name) you want to record. This will appear on the display:

4 Use CH+ A or CH- B to select the programme number (station

Programme numbers of the external inputs:

'EXT1' Scart socket at the back EXT 1 TO TV-I/O

'EXT2' Scart socket at the back EXT 2 AUX-I/O

'CAM1' Front SVHS/audio sockets S-VIDEO / left AUDIO right

'CAM1' Front video/audio sockets A/V S-VIDEO / left AUDIO right

'CAM2' Digital Video (i Link) front socket DV IN

RECORD on the DVD recorder.

'SAFE REC' appears on the display.

For DVD+R discs each new recording is always added at the end of

all previous recordings as existing recordings cannot be overwritten.

recordings, hold down the REC/OTR n button until the message

This will, for example, appear in the display:

If you want to start the recording at the end of the existing

5 To start recording, press REC/OTR n on the remote control or

1 FREETITLE P01

Which discs can I use for recording?

General

Manual recording

With this DVD recorder, you can record on two types of DVD:

DVD+RW

This disc can be written to and then the contents deleted.

DVD+R

This type of disc can only be recorded once.

ENGLISH

If you want to play this DVD in a DVD player it must be finalized using the

'Finalise disc' function. It is not possible to make further recordings using

this disc.

If this disc is to be played in a DVD recorder it must not be finalised.

Recordings can be added and deleted. The disc space (playback time) from the

deleted recording cannot be recovered for further recordings

Use the 'Manual recording' function to spontaneously start recording (e.g. to record a TV show

already in progress).

In the 'index display' select the title to be overwritten or 'Empty title' with CH- B , CH+ A .

If you insert recordings between existing recordings, check the lengths of the old and new

recordings. If the new recording is too long the subsequent recording (title/chapter) will be

overwritten.

Insert new recordings at the end of all existing recordings (Safe

Record)

To add a new recording at the end of the last recording on the disc, hold

Tip

display.

For DVD+R discs each new recording is always added at the end of all

previous recordings as existing recordings cannot be overwritten.

down the REC/OTR n button until the message 'SAFE REC' appears on the

End of disc is reached

If the end of a disc is reached during recording, recording will stop and the

Recorder will turn itself off automatically.

Please refer to section 'Recording without automatic switchoff', if you want to manually

start and stop your own recording.

If you want to start a recording manually but have it stopped automatically, read the section

'Recording with automatic switchoff'. (e.g. not to record to the end of the disc)

Read the section 'Automatic recording from a satellite receiver', if you want a recording

to be controlled automatically by a satellite receiver.

Read the section 'Direct record' if you want to record a programme currently being shown.

Manual recording

Directions For Use

EN 29DVDR70 & DVDR75/0x1 3.

switch to the internal tuner in the DVD recorder.

name) you want to record.

Recording with automatic switchoff

(OTR onetouchrecording)

1 Insert a disc.

2 If necessary, use the MONITOR button on the remote control to

3 Use CH+ A or CH- B to select the programme number (channel

4 Press REC/OTR n on the remote control.

Manual recording

time.

How can I cancel the recording time I have just entered?

To delete an entry, press CLEAR while the display shows the recording

recording time.

5 Each time you press REC/OTR n you will add 30 minutes to the

Preventing accidental erasing of discs

To ensure you don't accidentally delete a recording you can protect the entire disc. You can

only ever protect the entire disc. You cannot protect individual recordings.

What happens with DVD+R discs?

As long as these discs are not finalised, they can be protected against

accidental erasure in the same way as DVD+RW discs.

1 Insert the disc to be protected.

2 While the index screen is displayed press STOP h on the remote

control. The first title is highlighted.

3 Press CH+ A . This takes you to the disc info screen.

Select the 'Protection' line.

4 Press the C button.

Confirm with C .

5 Select 'Protected' with the CH- B button and confirm with OK .

6 Press D and then DISC-MENU to terminate.

Insert chapter markers

During recording you can mark scenes so you can find them or hide them

later.

appears on the TV screen. In the display, the number of the 'CHAPTER'

During recording, press FSS & at the start point. 'Inserting marker'

increases by one.

Tip

For further information on titles and chapters, see the section on 'Changing to

another title/chapter' in 'Playback'.

ENGLISH

machine to stop the recording. 'MENU UPDT' will appear on the display.

The DVD recorder is writing the list of contents. Wait until the

6 Use the STOP h button on the remote control or h on the

message disappears from the display. The recording is then complete.

aThe display will read 'DISC ERR'

b Recording could not be completed correctly because of a disc error. Check

Problem

the disc and clean it if necessary.

Making recordings on DVD+R discs compatible

If you want to play back the recording on a DVD player, you need to finalise

the disc in the DVD recorder. You can prepare your DVD for use in a DVD

Tip

player using the 'Finalising' feature. See 'Finalising DVD+R discs' in 'Managing

the disc contents'.

the commercials.

Interrupt recording (Pause)

1 During recording press PAUSE 9 , for example to avoid recording

Tip

disappears from the display.

End recording

To end the recording, press the STOP h button. Wait until 'MENU UPDT'

2 To continue recording, press REC/OTR n .

C01 1:16:51 P01

Manual recording

EN 30 DVDR70 & DVDR75/0x13.

the DVD recorder.

Select the record mode with the button REC MODE on the remote

Directions For Use

Which recording types can I choose?

'M1': High Quality offers the best picture quality and a recording time of 1

hour.

'M2': Standard Play (pre-recorded DVD quality) offers standard picture quality

control.

and a recording time of 2 hours.

'M2x': Standard Play plus (better than S-VHS quality) offers standard picture

quality and a recording time of 2.5 hours.

'M3': Long Play (S-VHS picture quality). Recording time of 3 hours.

Tip

Manual recording

' symbol with D or C .

C .

select the settings 'Stndrd' (Standard) or 'Sport' (for rapid movements)

In the line 'Record mode' select the recording type with D or C .5Confirm using OK and SYSTEM-MENU .6If you have selected the recording mode 'M3', 'M4'or'M6', you can

in the 'Filter mode' line.

Press the SYSTEM-MENU button.2Select '

Can I select the recording type via a menu as well?

Select 'Record settings' using CH- B or CH+ A and confirm with

'M4': Extended Play (better than VHS picture quality). Recording time of 4

hours.

'M6': Super Long Play (VHS picture quality). Recording time of 6 hours.

Selecting the recording type (Quality)

You can select the picture quality of the recording using the recording quality feature and hence

the maximum recording time per disc.

You can check the quality by changing the recording mode and then watching the picture from

the built-in tuner ( MONITOR button).

During playback, the correct picture quality will automatically be selected.

1 Switch on the TV set. If required, select the programme number for

ENGLISH

The entire disc is now protected.

If an attempt is made to record on a protected disc, 'DISC LOCK' will appear on the display and

'Disc locked' will appear on the screen.

Lining up recordings within a title

(assemble cut)

On a recorded DVD+RW disc you can add another recording to an existing title. This recording

is added to the title as a 'chapter'. The existing information will be overwritten starting from this

point. Titles will also be overwritten that follow the current title depending on the length of the

new recording. The recording type (Quality) will be taken from the current title.

What happens with DVD+R discs?

New recordings on 'DVD+R' discs can only be added after existing recordings.

It is not possible to overwrite existing recordings on 'DVD+R' discs.

To play back this recording, press SYSTEM-MENU and use the C button to select the 'C'

(Chapter) symbol. You can also use the T/C key.

For further information, see 'Changing to another title/chapter' in 'Playback'.

1 In the index display, find the title to which the new recording is to be

added.

2 Look at the last minute of the old recording (playback)

3 Press PAUSE 9 on the remote control at the position where the

new recording is to go. '9' will appear on the screen.

remote control.

The new recording will be inserted.

internal tuner.

4 To monitor the recording you can press MONITOR to switch to the

6 Stop recording with STOP h .

5 Now start recording as usual by pressing REC/OTR n on the

Manual recording

+ 230 hidden pages