Philips DVDR-3460 Service Manual

DVD-Video Recorder

CLASS 1

LASER PRODUCT

DVDR3460/75/97/96

Contents Page

1 Technical Speciﬁcations and Connection Facilities 2 2 Safety Information, General Notes & Lead Free Requirements 5 3 Directions for Use 7 4 Mechanical Instructions 10 5 Upgrade Software 13 6 Block Diagrams,Waveforms, Wiring Diagram 15 Overall block diagram 15 Wiring diagram 16 Waveforms of Analog Board 17 Waveforms of Digital Board 18 Test Point Overview for Analog Board 19 Test Point Overview for Digital Board 20 7 Circuit Diagram and PWB Layout 21 Front: Front Panel - Display 21 Layout: Front Display (Top View) 22 Layout: Front Display (Bottom View) 22 Front: Stanby 23 Layout: Standby (Top View) 23 Layout: Standby (Bottom View) 23 Analog: PSU and Tuner 24 Analog: Video input/output 25 Analog: MSP 26 Analog: Audio Converters 27 Layout: Analog-Main Part (Top View) 28 Layout: Analog-Main Part (Bottom View) 29

Copyright 2007 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

Contents Page Digital: Back-end Processor 30 Digital: Memory 31 Digital: 1394 & USB Interface 32 Digital: Interfaces 33 Layout: Digital-Main Part (Top View) 34 Layout: Digital-Main Part (Bottom View) 35 8 Exploded View & Spare Parts List 37 Exploded View of the set 37 Spare Parts List 38

Published by KC-TE 0715 V&MA Printed in the Netherlands Subject to modiﬁcation EN 3139 785 32500

Version 1.0

EN 2

3139 785 32500

Technical Speciﬁ cations and Connection Facilities

1. Technical Speciﬁ cations and Connection Facilities

1.1 PCB Locations

1.2 Diversity Matrix

/97/75 /96

Tuner PAL NTSC

PSU

ODD D6.1

Analog Board

Digital Board

Front Panel

(Behind the Front Plate)

1.4.3 Receiver:

Output of Cinch connector to be used for measurements (direct output from front end)

Video Performance:

1.3 General:

Power Supply : 110V-240V Mains Frequency : 50Hz – 60Hz Power consumption : 20W (typical) Standby Power consumption : < 3W

1.4 RF Tuner (Analogue)

Test equipment: Fluke 54200 TV Signal generator Test streams: Philips Standard test pattern

1.4.1 System

M, N (/96) B/G, I, L/L’, D/K (/97/75)

1.4.2 RF - Loop Through:

Frequency range : 43 MHz – 860 MHz Gain (ANT IN – ANT OUT) without ampliﬁ er : -4 dB ± 2 dB Gain (ANT IN – ANT OUT) with ampliﬁ er : From 2 dB + 3 dB until 2 dB – 2 dB

Frequency Response (/96) : -1 ± 3 dB

(0 to 3.58 MHz) Frequency Response (/97/75) : 0 ± 4 dB (0 to 4.4 MHz) Group Delay (/96) : 0 ± 150 n sec

(0 to 3.58 MHz) Group Delay (/97/75) : 0 ± 150 n sec

(0 to 4.4 MHz)

Audio Performance:

Audio analogue Mono/ BTSC (/96):

Frequency Response relative to 1 kHz : 0 ± 3 dB (100 Hz to 10 k Hz) S/N unweighted : ≥ 40 dB (Quasi peak,

22 Hz – 22 kHz) S/N weighted : ≥ 45 dB (Quasi peak,

CCIR 468) Harmonic distortion at 1 kHz : ≤ 1.5 % (FM: ± 25 kHz) Channel Separation : ≥ 20 dB

Audio analogue Mono (/97/75):

Frequency Response relative to 1 kHz : 0 ± 3 dB (100 Hz to 12 k Hz) S/N unweighted : ≥ 40 dB (Quasi peak,

22 Hz – 22 kHz) S/N weighted : ≥ 45 dB (Quasi peak,

CCIR 468) Harmonic distortion at 1 kHz : ≤ 1.5 % (FM: ± 25 kHz) Channel Separation : ≥ 20 dB

Technical Speciﬁ cations and Connection Facilities

3139 785 32500

EN 3

Audio NICAM Stereo/Dual (/97/75):

Frequency Response relative to 1 kHz : 0 ± 3 dB (40 Hz to 15 k Hz) S/N unweighted :  65 dB (Quasi peak,

22 Hz – 22 kHz)

S/N weighted :  70 dB (Quasi peak,

CCIR 468)

Harmonic distortion at 1 kHz :  0.5 % (Headroom:

System I – 21.1 dB, all others – 16.5 dB)

Channel Separation :  45 dB

1.4.4 Tuning

Tuning Frequency Range (/96) : 55 MHz – 805 MHz Tuning Frequency Range (/97/75) : 45.25 MHz – 857 MHz Antenna Level for 40dB luminance S/N (video unweighted) at 75 : < 40 dBV (High End)  60 dBV (Low End)

Automatic Search Tuning

Scanning time auto search without RF Signal : < 2.5 min. (Typical 3 minutes) Stop level (vision carrier) :  40 dBV Maximum tuning error during operation (drift) : ± 100 kHz Maximum tuning error of a recalled program : ± 62.5 kHz

Tuning Principles:

Automatic system recognition Manual Selection in “Store” mode Storage of frequencies at each random position number Direct channel access to “Off air” (A2-A69) or “Cable”

1.5 Analog Inputs / Outputs

1.5.1 Audio/Video Front Input Connectors

Audio - Cinch (L/R)

Input voltage : 2.2Vrms max Input impedance : > 10k

CAM (video) - Cinch

Input voltage : 1Vpp ± 3dB Input impedance : 75

1.5.2 Audio/Video Rear Input Connectors

Audio - Cinch (L/R)

Input voltage : 2.2Vrms max Input impedance : > 10k

1.5.3 Audio/Video Output Connectors

AUDIO – Cinch (L/R)

Output voltage : 2 Vrms max. Output impedance : > 10k

VIDEO (CVBS) – Cinch

Output voltage : 1 Vpp ± 3dB Output impedance : 75 

S-VIDEO (Y/C) - Hosiden

According to IEC 933-5 Superimposed DC-level on pin 4 (load  100 k): < 2.4V is detected as 4:3 aspect ratio > 3.5V is detected as 16:9 aspect ratio

Output voltage Y : 1 Vpp ± 3dB Output impedance Y : 75  Output voltage C : 300 mVpp ± 3dB Output impedance C : 75 

COMPONENT VIDEO – Cinch (Y/Pb/Pr)

According to EIO-770-I-A, EIA-770-2

1.6 Digital Inputs / Outputs

1.6.1 IEEE 1394 Digital Video Input (DV IN)

Implementation Standard according:

IEEE Std 1394-1995 IEC61883 - Part 1 IEC61883 - Part 2 SD-DVCR (02-01-1997)

Speciﬁ cation of consumer use digital VCR’s using 6.3mm

magnetic tape – dec.1994

Mechanical connection according to Annex of IEC 61883-1

1.6.2 Digital Output

DIGITAL AUDIO – Cinch

LPCM : according IEC 60958 MPEG 1, MPEG 2, AC3 : according IEC 61937 DTS : according IEC 61937 +

addendum

1.7 Video Performance

1.7.1 SNR

PAL

RGB CVBS Y/C

 55 dB Lumincance:  55 dB

Chroma:  55 dB (AM)  52 dB (PM)

Y:  57 dB C:  57 dB (AM)  54 dB (PM)

EXT1 VIDEO(CVBS) - Cinch

Input voltage : 1Vpp ± 3dB Input impedance : 75

EXT2 S VIDEO (Y/C) – Hosiden

According to IEC 933-5 Superimposed DC-level on pin 4 (load > 100k): < 2.4V is detected as 4:3 aspect ratio > 3.5V is detected as 16:9 aspect ratio

Input voltage Y : 1 Vpp ± 3dB Input impedance Y : 75  Input voltage C : 300 mVpp ± 3dB Input impedance C : 75  Input impedance : > 10k

NTSC

Y Pb Pr CVBS Y/C

 55 dB Lumincance:  55 dB

Chroma:  54 dB (AM)  54 dB (PM)

Y:  55 dB C:  54 dB (AM)  54 dB (PM)

EN 4

3139 785 32500

Technical Speciﬁ cations and Connection Facilities

1.7.2 Bandwidth

PAL

RGB CVBS Y/C

0.5 to 4 MHz:+1dB/2dB

4.8 MHz:-3dB 4.8 MHz:-3dB C:700 kHz

5.8 MHz:-6dB 5.8 MHz:-6dB

NTSC

YPbPr CVBS Y/C

4.2 MHz:-3dB 4.2 MHz:-3dB Y:4.2MHz-3dB

5.8 MHz:-6dB 5.8 MHz:-6dB C: 700 kHz

With Pscan: 8.4MHz

-3dB

0.5 to 4 MHz:+1dB/2dB

Y:4.8MHz-3dB

1.8 Audio Performance CDDA (PCM)

1.8.1 Cinch Output Rear

Output voltage 2 channel mode : 2Vrms ± 1dB Channel unbalance (1kHz) :  |0.22| dB (0.05V) Crosstalk 1kHz :  |100| dB Crosstalk 16Hz-20kHz :  |90| dB Frequency response :  |0.2| dB Frequency response with

de-emphasis :  |0.5| dB Signal to noise ratio (unweighted) :  - 95 dB Signal to noise ratio (A-weighted) :  - 100 dB Signal to noise ratio (unweighted) :  - 115 dB Dynamic range 1kHz :  |90| dB Distortion and noise 1kHz :  -85 dB Distortion and noise 16Hz-20kHz :  -85 dB Intermodulation distortion :  0.002 %

Intermodulation distortion :  0.002 % (-94 dB)

Phase Difference between channels: 1 sample Phase non-linearity : ± 2° Level non-linearity (-60dB to –90dB):  |1.0| dB Output polarity : 7FFF (H) positive pulse at output 8000 (H) negative pulse at output Mute :  -95 dB (during spin-

Outband attenuation :  -40 dB above 30 kHz

(60 Hz and 7 kHz)

(19 kHz and 20 kHz)

up, spin-down, pause and access)

1.11 Playability

Video Playback

1. Disc playback media: CD, CD-R/-RW, DVD, DVD-Video, DVD+R/+RW, DVD-R/-RW SVCD, Video CD, DVD+R DL, DVD-R DL Video disc playback system: PAL, NTSC

2. Compression formats: MPEG2, MPEG1, DivX

Audio Playback

1. Disc playback media: CD, CD-R/-RW, MP3-CD, MP3-DVD

2. Compression formats: Dolby Digital, MP3, MPEG2 Multichannel, PCM

3. MP3 bit rates: 32~256 kbps and VBR x

Still Picture Playback

1. Disc formats: DVD+R/+RW, DVD-R/-RW, DVD+R DL, DVD-R DL, Picture CD

2. Picture Compression Format: JPEG

3. Picture enhancement: Rotate, Zoom

1.12 Supported Disc Types and Media Speed for Recording

Disc Media speeds

DVD+R 1x - 16x

DVD+RW 2.4 x - 4x

DVD-R 1x - 16x

DVD-RW 2x - 4x

DVD+R DL 2.4x - 8x

DVD-R DL 4x

1.9 Dimension and Weight

Set Dimension W x D x H : 360 x 43 x 322mm Net Weight : 3 kg

1.10 Laser Output Power & Wavelength

1.10.1 DVD

Output power during reading : 0.8mW Output power during writing : 20mW Wavelength : 650nm

1.10.2 CD

Output power : 0.3mW Wavelength : 780nm

Safety Information, General Notes & Lead Free Requirements

3139 785 32500

2. Safety Information, General Notes & Lead Free Requirements

EN 5

2.1 Safety Instructions

2.1.1 General Safety

Safety regulations require that during a repair:

• Connect the unit to the mains via an isolation transformer.

• Replace safety components, indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of ﬁ re or electrical shock hazard.

Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points:

• Route the wires/cables correctly, and ﬁ x them with the mounted cable clamps.

• Check the insulation of the mains lead for external damage.

• Check the electrical DC resistance between the mains plug and the secondary side:

1. Unplug the mains cord, and connect a wire between the two pins of the mains plug.

2. Set the mains switch to the ‘on’ position (keep the mains cord unplugged!).

3. Measure the resistance value between the mains plug and the front panel, controls, and chassis bottom.

4. Repair or correct unit when the resistance measurement is less than 1 M.

5. Verify this, before you return the unit to the customer/ user (ref. UL-standard no. 1492).

6. Switch the unit ‘off’, and remove the wire between the two pins of the mains plug.

2.1.2 Laser Safety

This unit employs a laser. Only qualiﬁ ed service personnel may remove the cover, or attempt to service this device (due to possible eye injury).

2.2 Warnings

2.2.1 General

• All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD, ). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same potential. Available ESD protection equipment: – Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. – Wristband tester 4822 344 13999.

• Be careful during measurements in the live voltage section. The primary side of the power supply, including the heatsink, carries live mains voltage when you connect the player to the mains (even when the player is ‘off’!). It is possible to touch copper tracks and/ or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touching this area or components in this area. A ‘lightning stroke’ and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply.

• Never replace modules, or components, while the unit is ‘on’.

2.2.2 Laser

• The use of optical instruments with this product, will increase eye hazard.

• Only qualiﬁ ed service personnel may remove the cover or attempt to service this device, due to possible eye injury.

• Repair handling should take place as much as possible with a disc loaded inside the player.

• Text below is placed inside the unit, on the laser cover shield:

Laser Device Unit

Type : Semiconductor laser GaAlAs Wavelength : 650 nm (DVD) : 780 nm (VCD/CD) Output Power : 20 mW (DVD+RW writing) : 0.8 mW (DVD reading) : 0.3 mW (VCD/CD reading) Beam divergence : 60 degree

CLASS 1

LASER PRODUCT

Figure 2-1

Note: Use of controls or adjustments or performance of procedure other than those speciﬁ ed herein, may result in hazardous radiation exposure. Avoid direct exposure to beam.

CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D’OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU

Figure 2-2

2.2.3 Notes

Dolby

Manufactured under licence from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. Conﬁ dential Unpublished Works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.

Figure 2-3

Trusurround

TRUSURROUND, SRS and symbol (ﬁ g 2-4) are trademarks of SRS Labs, Inc. TRUSURROUND technology is manufactured under licence frm SRS labs, Inc.

Figure 2-4

EN 6

3139 785 32500

Safety Information, General Notes & Lead Free Requirements

Video Plus

“Video Plus+” and “PlusCode” are registered trademarks of the Gemstar Development Corporation. The “Video Plus+” system is manufactured under licence from the Gemstar Development Corporation.

Figure 2-5

Macrovision

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

2.3 Lead Free Requirement

Information about Lead-free produced sets

Philips CE is starting production of lead-free sets from

1.1.2005 onwards.

INDENTIFICATION:

Regardless of special logo (not always indicated)

One must treat all sets from 1 Jan 2005 onwards, according next rules.

Example S/N:

Due to lead-free technology some rules have to be respected by the workshop during a repair:

• Use only lead-free solder alloy Philips SAC305 with order code 0622 149 00106. If lead-free solder-pate is required, please contact the manufacturer of your solder-equipment. In general use of solder-paste within workshops should be avoided because paste is not easy to store and to handle.

• Use only adequate solder tools applicable for lead-free solder alloy. The solder tool must be able

o To reach at least a solder-temperature of 400°C, o To stabilize the adjusted temperature at the solder-tip o To exchange solder-tips for different applications.

• Adjust your solder tool so that a temperature around 360°C – 380°C is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400°C otherwise wear-out of tips will rise drastically and ﬂ ux-ﬂ uid will be destroyed. To avoid wear-out of tips switch off un-used equipment, or reduce heat.

• Mix of lead-free solder alloy / parts with leaded solder alloy / parts is possible but PHILIPS recommends strongly to avoid mixed solder alloy types (leaded and lead-free). If one cannot avoid or does not know whether product is lead-free, clean carefully the solder-joint from old solder alloy and re-solder with new solder alloy (SAC305).

• Use only original spare-parts listed in the Service-Manuals. Not listed standard-material (commodities) has to be purchased at external companies.

• Special information for BGA-ICs:

- always use the 12nc-recognizable soldering temperature proﬁ le of the speciﬁ c BGA (for de-soldering always use the lead-free temperature proﬁ le, in case of doubt)

- lead free BGA-ICs will be delivered in so-called ‘drypackaging’ (sealed pack including a silica gel pack) to protect the IC against moisture. After opening, dependent of MSL-level seen on indicator-label in the bag, the BGA-IC possibly still has to be baked dry. (MSL=Moisture Sensitivity Level). This will be communicated via AYSwebsite.

Do not re-use BGAs at all.

• For sets produced before 1.1.2005 (except products of

2004), containing leaded solder-alloy and components, all needed spare-parts will be available till the end of the service-period. For repair of such sets nothing changes.

Bottom line of typeplate gives a 14-digit S/N. Digit 5&6 is the year, digit 7&8 is the week number, so in this case 1991 wk 18

So from 0501 onwards = from 1 Jan 2005 onwards

Important note: In fact also products of year 2004 must be treated in this way as long as you avoid mixing solder-alloys (leaded/ lead-free). So best to always use SAC305 and the higher temperatures belong to this.

• On our website www.atyourservice.ce.Philips.com you

 BGA-de-/soldering (+ baking instructions)  Heating-proﬁ les of BGAs and other ICs used in Philips-sets

You will ﬁ nd this and more technical information within the

For additional questions please contact your local repair-helpdesk.

ﬁ nd more information to:

“magazine”, chapter “workshop news”.

Directions For Use

PBPR

VIDEO

(

CVBS

)

EXT 2

S-VIDEO

(

Y/C

)

EXT 1

EXT 3

COMPONENT VIDEO

AUDIO

ANTENNA-IN

TV-OUT

INPUT

COMPONENT

VIDEO

(

CVBS

)

S-VIDEO

(

Y/C

)

AUDIO

COAXIAL

OUT 3

(DIGITAL AUDIO)

UT 2

UT 1

dvdr3460-96_QSG_EN_26641.indd 2 2007-03-22 10:15:22 AM

3139 785 32500

3. Directions For Use

The following except of the Quick Use Guide serves as an introduction to the set. The Complete Direction for the Use can be downloaded in different languages from the internet site of Philips Customer care Center:

www.p4c.philips.com

To AC

power

EN 7

Television (rear)

S-VIDEO

OUT

AUDIO

R L

VIDEO

Cable box/ Satellite

receiver (rear)

To antenna or

Connection with a Cable Box

or Satellite Receiver

Television (rear)

Connect

Start with the ‘Basic Connection.’

If you have a Cable Box or Satellite Receiver, follow the instructions for ‘Connection with a

Cable Box or Satellite Receiver’.

Basic Connection

set-top box

To antenna

or set-top

box

To AC

power

AUDIO

OUT 3

COAXIAL

(DIGITAL AUDIO)

) Y/C (

S-VIDEO

DVD Recorder

(rear)

before you proceed to step D below.

Antenna TV signal to the Cable Box/ Satellite

A Keep the existing antenna connection from the

connect it to the ANTENNA-IN socket on

A Disconnect the antenna cable from your TV and

RF OUT jack on the Cable Box/Satellite Receiver.

Receiver.

ANTENNA-IN jack on the recorder to the

B Use an antenna cable to connect the

this recorder.

TV-OUT socket on this recorder to the

Antenna In socket on the TV.

B Use an RF antenna cable to connect the

depending on the Satellite Receiver/Cable Box.

Refer to its user manual for proper antenna

connection.

Note The antenna connection may be different

C Follow steps C to E under ‘Basic Connections’

connect the VIDEO (CVBS) OUTPUT jack on

C Use the supplied video cable (yellow plug) to

D Use the yellow video cable (not supplied) to

on this recorder to the AUDIO IN jacks on the

this recorder to the VIDEO IN jack on the TV.

plugs) to connect the AUDIO OUTPUT jacks

D Use the supplied audio/video cable (red/ white

connect the VIDEO (CVBS) INPUT jack on

TV.

this recorder to the VIDEO OUT jack on the

Cable Box/ Satellite Receiver.

supplied) to connect the AUDIO INPUT jack

on this recorder to the AUDIO OUT jack on

the Cable Box/ Satellite Receiver.

For additional connection diagrams, see the

E Use the audio cable (red/white plugs – not

an AC power outlet.

E Connect the power cable from the recorder to

accompanying User Manual.

User

Manual

Connect

Enjoy

Set up

and 2 batteries

Remote Control

Audio/video cable

DVD Player/ Recorder

RF antenna Cable

DVD Player/ Recorder DVDR3460

Quick Start Guide

What’s in the box?

EN 8

Welcome

Before using the recorder,

please complete the initial installation.

Tuner Mode

BACK

Next Page Prev Page

Select current tuner mode.

Antenna

Cable

Cancel

Auto scan the channels.

Auto Scan

100%

BACK

Next Page Prev Page

Set the system time.

Clock Setting

BACK

Next Page Prev Page

Date: Time:

01 01 2007 12 00 00

Finish

BACK

Exit Prev Page

The installation is completed.

The recorder is now ready for use.

Welcome

Before using the recorder,

please complete the initial installation.

Menu Language

BACK

Select a menu language.

English

Cancel

Auto scan the channels.

Channels found: 10

Auto Scan

100%

BACK

Next Page Prev Page

Program List

BACK

Next Page Prev Page

1 P01 On C03

2 P02 On C13

3 P03 On S08

Sort and rename the programs.

PR Station NICAM CH

Move Up

Move Down

NICAM

Rename

Set the system time.

Clock Setting

BACK

Next Page Prev Page

Date: Time:

01 01 2007 12 00 00

Finish

BACK

Exit Prev Page

The installation is completed.

The recorder is now ready for use.

appears.

3139 785 32500

Note In this menu, you can change the TV channels

sequence, rename it or set NICAM mode. For detailed

descriptions, refer to the accompanying User Manual.

C Once auto search completes, the program list menu

Directions For Use

The clock setting menu appears.

D Press OK on the remote control to continue.

use W X keys to select different entry fields.

E Use ST keys to set the current date and time,

Note You may use the numeric keypad 0-9 on

the remote control to enter the date and time.

installation screen appears.

F Once complete, press OK to confirm. The final

The DVD recorder is now ready for use.

G Press OK to exit.

/75/97

Set up

B Press OK on the remote control.

Finding the viewing channel

(e.g. Cable Box, Satellite Receiver).

You should see the welcome menu.

Press STANDBY-ON on the recorder.

B Turn on the TV and other connected devices

The auto scan menu appears and the automatic

TV channel search starts.

Note This process may take several minutes.

menu, press the Channel Down button on the

C In case you don’t see the recorder’s welcome

The clock setting menu appears.

C Press OK on the remote control to continue.

The

TV’s remote control repeatedly (or AV, SELECT,

Start basic setup

° button) until you see the menu. This is the

correct viewing channel for the recorder.

Use the recorder’s remote control and

D Use ST keys to set the current date and time,

language setting menu appears.

follow the on-screen instructions to

complete the installation.

A Press OK on the remote control.

Note You may use the numeric keypad 0-9 on

the remote control to enter the date and time.

use W X keys to select different entry fields.

installation screen appears.

E Once complete, press OK to confirm. The final

display and press OK.

The auto scan menu appears and the automatic TV

channel search starts.

Note This process may take several minutes.

B Select the language for this recorder’s on-screen

The DVD recorder is now ready for use.

F Press OK to exit.

/96

Set up

Finding the viewing channel

(e.g. Cable Box, Satellite Receiver).

You should see the welcome menu.

Press STANDBY-ON on the recorder.

B Turn on the TV and other connected devices

SELECT, ° button) until you see the menu.

C In case you don’t see the recorder’s welcome

Use the recorder’s remote control

Use ST keys to select the tuner mode.

and follow the on-screen instructions

to complete the installation.

A Press OK on the remote control.

Start basic setup

This is the correct viewing channel for

the recorder.

menu, press the Channel Down button on the

TV’s remote control repeatedly (or AV,

{ Antenna }

if the recorder is connected directly to an indoor or

outdoor antenna.

{ Cable }

if the recorder is connected directly to the cable signal or

through set-top box.

Hours of Recording

that can be stored

Hours of Recording

that can be stored

Types of discs for recordingTypes of discs for recording

Record QualityRecord Quality

12346

High Quality HQ

Standard Play SP

Long Play LP

Extended Play EP

Super Long Play SLP

4.7 GB

DVD±R/±RW disc

DVD±R DL

dvdr3460-96_QSG_EN_26641.indd 1 2007-03-22 10:15:20 AM

Directions For Use

3139 785 32500

EN 9

Enjoy

up S or down T

load in a disc and close the disc tray.

Press DISC MENU, then use

Press PLAY/PAUSE u to start playback.

To stop playback, press STOP x.

Start playback

Start recording

keys to select a title.

A Press OPEN/CLOSEç to open the disc tray,

To record a TV programme, use up S

down T keys to scroll through the channels, or

press 0 -9 to select the channel that you want to

Insert a recordable DVD into the recorder.

Press SOURCE repeatedly to select the source

to record from. (eg, TUNER, CAM1, DV, EXT1

Recording from the TV or an external

device

or EXT2).

record.



to start recording.

RECORDâ

Press REC MODE repeatedly to select a desired

recording mode.

It determines the picture quality and recording

time to the recordable DVD.

D Press

PLAY/PAUSE

STOP x

repeatedly to toggle between

To set the recording length, press

RECORDâ

scheduled time, press

30, 60 and 90 minutes recording time.



E To stop the recording before the

Need help?

User Manual

See the user manual that came with your Philips recorder.

Online

Go to www.philips.com/welcome

12 NC 3139 245 26641

EN 10

3139 785 32500 Mechanical Instructions

4. Mechanical Instructions

Note: The position numbers given here refer to the Exploded view in chapter 8.

4.1 Dismantling of the DVD Tray Cover manually

1) Insert a screw-driver into the slot provided at the bottom of the set and push in the direction as shown in Figure 1 to unlock before sliding the Tray cover 110 out.

Figure 4-1: unlock the tray loader

2) Remove the Tray Cover 110 as shown in Figure 2 .

4.2 Dismantling of the Front Panel

1) Remove 7 screws to loosen Top cover 240.

2) Remove 3 screws, loosen the Plate Front Loader 182 and detach the Front Assembly (Plate Front Loader 182 + Front Panel) as shown in Figure 3. The Front Panel Service Position is shown in Figure 4.

Plate Front Loader 183

Front Panel

Figure 4-3: detach the front panel

Figure 4-2: remove the Tray cover

Insulation Sheets

Figure 4-4: Front Panel Service Position

Mechanical Instructions

3139 785 32500

EN 11

4.3 Dismantling of the Basic Engine

1) Remove screws to loosen the Plate Front Loader 182 from the Front Assembly.

2) Remove 4 mounting screw and detach the Basic Engine 1001 from the Frame 161 as shown in ﬁ gure 5.

Figure 4-5: Basic Engine mounting screw

Basic Engine

Assembly

Frame

161

4.4 Dismantling of the PSU Board

1) Remove 3 screws to loosen the PSU Board 1002 as shown in Figure 7.

Figure 4-7: PSU remove mounting screws

2) Service position for PSU Board is given in Figure 8.

3) Flip the Basic Engine 1001 over to remove 4 screws from the PCB protection plate. Service Position of the Basic Engine is shown in Figure 6.

Insulation

Sheets

PCB Protection

Plate

Figure 4-6: Basic Engine Service Position

Insulation Sheet

Figure 4-8: PSU Board Service Position

EN 12

3139 785 32500 Mechanical Instructions

4.5 Dismantling of the Digital Board

1) Remove 4 screws to loosen the Digital Board 1004 as shown in Figure 9.

Figure 4-9: Remove mounting screws for Digital Board

2) Service position for Digital Board is given in Figure 10. The Front Panel should also be detached from the frame 161 in order to ﬂ ip over the Digital Board for servicing.

4.6 Dismantling of the Analog Board

1) Remove 6 screws from the Rear Panel 230. Remove 3 more screws that attach the Analog Board 1003 to the Frame 161 and detach the Analogue Board 1003.

2) Detach the Rear Panel 230 from the Frame 162 by removing 1 screw. Analogue Board Service Position is shown in Figure 13.

Insulation

Sheet

Figure 4-11: Analogue Board Service Position (Rear Panel

detached from the Frame)

Notes: While ﬂ ipping over the Analog Board for service, beware of the connections to the PSU, Basic Engine and Digital Board.

Beware of the

Insulation

Sheet

connection

Insulation

Figure 4-10: Digital Board Service Position

Sheet

+ 26 hidden pages

Philips DVDR-3460 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual