Page 1
Quick Start Guide
DC912
What’s in the Box?
You should find these items upon opening the box.
2
User Manual
Quick Start Guide
AC power cord
(for the subwoofer)
Quick Start Guide
User Manual
1
Remote Control
AC power adaptor
Pull out the plastic
protective sheet
before use.
3 X iPod dock adaptors
Page 2
1
Connect the AC power cord of the subwoofer to the AC outlet.
2
Connect the AC power adaptor of the system.
In case the wireless connection fails due to conflict or strong
interference etc., you may need the following procedures for
manual pairing:
1 In standby mode, press and hold 2; on the set for three seconds to
activate signal transmitting.
➜“PAIR” flashes on the display screen.
2 Press and hold the PA IR button on the rear of the subwoofer for
three seconds to activate signal receiving.
➜The LED indicator on the subwoofer flashes in blue and green
alternatively.
● If the connection succeeds, the display shows “PASS”.
● If the connection fails or the connection cannot be set up successfully
within 60 seconds, the display shows “FAIL”.
Tip
– See the User Manual for how to
connect other equipment to this
system.
– Use the supplied AC power
adaptor only! Using any other
power connection device may
damage your main set!
1
2
Setting the clock
1
In standby mode, press and hold PROG/SET TIME on the remote control.
2
Press VOLUME +/- (or VOL +/- on the remote control) to switch
between 12 hour and 24 hour display.
3
Press PROG/SET TIME on the remote control again to confirm.
➜ The clock digits flash on the display panel.
4
Press VOLUME +/- (or VOL +/- on the remote control) to set the hours.
5
Press PROG/SET TIME on the remote control again.
➜ The clock digits for the minutes flash.
6
Press VOLUME +/- (or VOL +/- on the remote control) to
set the minutes.
7
Press PROG/SET TIME on the remote control to confirm the time.
Page 3
C
Enjoy
Programming and tuning to radio stations
1
Press SOURCE repeatedly (or TUNER on the remote control) to select the
tuner source (FM).
2
Press PROG for more than two seconds to program all available stations in order
of waveband.
3
Press PRESET +/- (or ALBUM/PRESET 3 / 4 on the remote control) until the
desired preset station is displayed.
Playing a USB mass storage device/SD/MMC card
With the Hi-Fi system, you can use USB flash memory (USB 2.0 or USB1.1),
USB flash players
1
Insert the USB device’s USB plug into the socket or fully insert the SD/MMC card into
the SD/MMC slot on the top of the system.
2
Press SOURCE once or more (or USB/CARD on the remote control) to select
USB/CARD.
3
Play the available audio files using playback buttons on the set or remote control (such as
2;, S/T).
(USB 2.0 or USB1.1) and memory cards
Page 4
C
Enjoy
Playing Apple iPod using DC912
1
Select the correct dock adaptor, as indicated on each adaptor, then fit it in
the dock.
2
Correctly place the compatible iPod player into the dock.
3
Press SOURCE on the system repeatedly or iPod on the remote control
to select the iPod source.
4
Power on your iPod player.
5
Select and play your favourite songs stored in the iPod player.
Tip
Detailed playback features and additional functions are described in the
accompany owner's manual.
Notes for remote control:
– First select the source you wish to control by pressing one of the
source select keys on the remote control (for example iPod,
TUNER).
– Then select the desired function (for example ÉÅ, à, á).
C Royal Philips Electronics N.V. 2008
All rights reserved.
PDCC-ZYL-0835
Loading...