Always there to help you
Question?
Contact
Philips
Register your product and get support at
www.philips.com/support
CSS5235Y
User manual
Contents
1 Important 2
Safety 2
Mains fuse 3
Care for your product 3
Care of the environment 3
Compliance 3
Help and support 4
2 Your product 4
Main unit 4
Remote control 5
Connectors 6
Wireless speakers 7
Wireless subwoofer 7
3 Connect and set up 8
Connect the main unit 8
Charge speakers 8
Pair up with speakers/subwoofer 8
Place speakers 9
Connect to TV 10
Connect audio from TV and other
devices 10
English
7 Troubleshooting 17
4 Use your product 12
Adjust the volume 12
Choose your sound 12
Play music via Bluetooth 12
Play music via NFC 13
MP3 player 13
USB storage devices 14
Auto standby 14
Apply factory settings 14
5 Update software 15
Check software version 15
Update software via USB 15
6 Product specications 16
EN
1
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure
to follow instructions, the warranty does not
apply.
Safety
Risk of electric shock or re!
• Before you make or change any
connections, make sure that all devices are
disconnected from the power outlet.
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Consumer Care to
have the product checked before use.
• Never place the product and accessories
near naked ames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, re or the like.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Risk of short circuit or re!
• For identication and supply ratings, see
the type plate at the back or bottom of
the product.
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
Risk of injury or damage to this product!
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
Risk of overheating!
• Never install this product in a conned
space. Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Risk of contamination!
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
• Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Risk of swallowing batteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
2
EN
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
• If the battery compar tment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Mains fuse
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
English
This information applies only to products with a
UK mains plug.
This product is tted with an approved molded
plug. If you replace the fuse, use one with:
• the ratings shown on the plug,
• a BS 1362 approval, and
• the ASTA approval mark.
Contact your dealer if you are not sure about
what type of fuse to use.
Caution: To conform with the EMC directive
(2004/108/EC), do not detach the plug from
the power cord.
Copyright in the U.K.
• Recording and playback of material may
require consent. See Copyright Act 1956
and The Performer’s Protection Acts 1958
to 1972.
Care for your product
Use only microber cloth to clean the product.
This symbol means that the product contains
batteries covered by European Directive
2013/56/EU which cannot be disposed of with
normal household waste.
Inform yourself about the local separate
collection system for electrical and electronic
products and batteries. Follow local rules and
never dispose of the product and batteries
with normal household waste. Correct disposal
of old products and batteries helps prevent
negative consequences for the environment and
human health.
Removing the disposable batteries
To remove the disposable batteries, see battery
installation section.
Compliance
This product complies with the radio
interference requirements of the European
Community.
EN
3
Hereby, Gibson Innovations, declares that this
product is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
A copy of the EC declaration of Conformity is
available at www.philips.com/support.
Help and support
2 Your product
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
For extensive online support, visit
www.philips.com/support to:
• download the user manual and the quick
start guide
• watch video tutorials (available only for
selected models)
• nd answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select
your language, and then enter your product
model number.
Alternatively, you can contact Consumer Care
in your country. Before you contact, note down
the model number and serial number of your
product. You can nd this information on the
back or bottom of your product.
Main unit
The main unit of this product is comprised of
left and right base speakers.
a
b
c
d
e
f
a LED indication
Red LED
• Lights up when the main unit is
switched to standby.
White LED
• Lights up when the main unit is
switched on.
• Blinks once each time you press a
button on the remote control.
• Blinks twice when Dolby Digital audio
is input.
• Blinks three times when DTS audio is
input.
4
EN
b
a
c
d
f
h
i
e
g
j
• Blinks continuously when no audio
from the selected HDMI ARC source
is detected, or when an unsupported
audio format is detected.
Blue LED
• Lights up when you switch to
Bluetooth mode and Bluetooth devices
are paired.
• Blinks when you switch to Bluetooth
mode and Bluetooth devices are not
paired.
b NFC tag
Tap the NFC-enabled device on the tag for
Bluetooth connection.
c
(Standby-On)
Switch the main unit on or to standby.
d
Switch to Bluetooth mode.
e
Toggle through all sources.
f Volume +/-
Increase or decrease volume.
Remote control
This section includes an overview of the
remote control.
English
a (Standby-On)
• Switch the main unit on or to standby.
b Source buttons
COAX: Switch your audio source to the
coaxial connection.
OPTICAL: Switch your audio source to
the optical connection.
AUX: Switch your audio source to the
connection of an external device with
3.5mm jack or with red/white audio jacks.
USB: Switch to USB mode.
EN
5
: Switch to Bluetooth mode; Press and
h
hold three seconds to break the current
Bluetooth connection.
HDMI ARC: Switch your source to HDMI
ARC connection.
c
/
Skip to the previous or next track in USB
mode and Bluetooth mode (only for
AVRCP-supported Bluetooth devices).
d
Start, pause or resume play in USB mode
and Bluetooth mode ( only for AVRCPsupported Bluetooth devices).
e BASS +/-
Increase or decrease bass.
f Volume control
• +/-: Increase or decrease volume.
•
: Mute or restore volume.
g Sound mode control
VOICE: Select voice clarity sound mode.
MUSIC: Select stereo sound mode.
MOVIE: Select surround sound mode.
h AUDIO SYNC +/-
Increase or decrease audio delay.
i NIGHT ON/OFF
Turn night mode on or off.
j TREBLE +/-
Increase or decrease treble.
Connectors
This section includes an overview of the
connectors available on this product.
a cb d ef g
a TO R SPEAKER
Connect to the right base speaker.
b DC IN
Connect to the power supply.
c TO L SPEAKER
Connect to the left base speaker.
d COAXIAL
Connect to a coaxial audio output on the
TV or a digital device.
e
• Audio input from a USB storage device.
• Upgrade software of this product.
• Charge a USB device.
f OPTICAL
Connect to an optical audio output on the
TV or a digital device.
g AUDIO IN
Audio input from, for example, an
MP3 player (3.5mm jack).
h TO TV - HDMI OUT (ARC)
Connect to the HDMI (ARC) input on the
TV.
6
EN
Wireless speakers
This product comes with a pair of wireless
surround speakers.
b
• Switch the surround speaker on.
• The surround speaker automatically
turns off after 4 minutes of being
wirelessly disconnected from the main
unit.
Wireless subwoofer
This product comes with a wireless subwoofer.
English
* The illustration above is for either of wireless
surround speakers.
a LED indicaton
a b
Red LED
• Lights up when the battery capacity
is less than 30% remaining (undocked
from the main unit).
• Blinks when the battery capacity is less
than 10% remaining (undocked from
the main unit).
• If the speaker is not wirelessly
connected to the main unit, the LED
blinks red and orange alternatively.
White LED
• Lights up when the battery capacity
is full or more than 30% remaining
(undocked from the main unit).
• Lights up when the speaker is
wirelessly connected to the main unit
(undocked from the main unit).
Orange LED
• Lights up when the surround speaker
is being charged (only for the wireless
speaker docked onto the main unit).
• If the speaker is not wirelessly
connected to the main unit, the LED
blinks red and orange alternatively.
a
b
c
a CONNECT (connect)
Press to to enter the pairing mode for the
subwoofer.
b Subwoofer indicator
• When the power is turned on, the
indicator lights up.
• During wireless pairing between the
subwoofer and the main unit, the
indicator blinks white quickly.
• When the pairing succeeds, the
indicator lights up white.
• When the pairing fails, the indicator
blinks white slowly.
• When wireless connection is
disconnected for 4 minutes, the
indicator turns off.
c AC MAINS~
Connect to the power supply.
EN
7
3 Connect and set
up
This section helps you connect this product to a
TV and other devices, and then set it up.
For information about the basic connections of
this product and accessories, see the quick start
guide.
Note
For identication and supply ratings, see the type plate
•
at the back or bottom of the product.
• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Connect the main unit
1 Dock the left and right wireless speakers
onto the main unit (the left and right base
speakers) to charge the speakers.
2 Turn on the main unit.
» During charging, the orange LED on
the wireless speaker lights up.
» When fully charged, the orange LED
on the wireless speaker turns off.
With the supplied DIN cable, connect the left
base speaker to the right base speaker as main
unit. See the quick start guide for details.
Charge speakers
If the wireless surround speaker is undocked
from the main unit, its battery level is indicated
by the LED on the wireless speaker.
• Light up white: full battery or more than
30% capacity remaining
• Light up red: low battery level, less than
30% remaining
• Blink red: near empty, less than 10%
remaining
8
EN
Note
It may take around 3 hours to fully charge the speakers.
•
Pair up with speakers/ subwoofer
The wireless speakers and subwoofer
automatically pair up with the main unit (left
and right base speakers) for wireless connection
when you turn on the main unit, the speakers
and the subwoofer.
If no audio from the wireless speakers and
subwoofer can be heard, do the following for
pairing.
Pair up with the speakers
1 Turn on the main unit and the surround
wireless speakers.
» If the connection to the main unit is
lost, the red and orange LEDs on the
wireless speaker blink alternatively.
2 Dock the left and right wireless speakers
onto the main unit (the left and right base
speakers) to pair up automatically.
» If the pairing is successful, the orange
LED on the wireless speaker lights up
for ve seconds.
» If the pairing fails, the red and orange
LEDs on the wireless speaker blinks
alternatively.
3 If the paring fails, re-dock the wireless
speakers onto the main unit.
Pair up with the subwoofer
1 Turn on the main unit, and the subwoofer.
» If the connection to the main unit is
lost, the white LED on the subwoofer
blinks slowly.
2 Press the CONNECT (connect) button
on the subwoofer to enter the pairing
mode.
» The white LED on the subwoofer
blinks quickly.
3 In OPTICAL mode (press OPTICAL) ,
within six seconds, on the remote control,
press
twice then Volume + once, and
then hold down BASS +.
» If the pairing succeeds, the white LED
on the subwoofer lights up.
» If the pairing fails, the white LED on
the subwoofer blinks slowly.
4 If the pairing fails, repeat the steps above.
Note
After the subwoofer is manually connected to the main
•
unit, pair the surround speakers with the main unit
again for re-connection.
Place speakers
For best sound effect, position all the speakers
towards the seating position and place them
close to your ear level (seated).
SUB
WOOFER
Note
Surround sound depends on factors such as room
•
shape and size, type of wall and ceiling, windows and
reective surfaces, and speaker acoustics. Experiment
with the speaker positions to nd the optimum setting
for you.
Follow these general guidelines for speakers
placement.
1 Seating position:
This is the center of your listening area.
2 Place the main unit (left and right base
speakers) in front of the seating position.
English
RL
EN
9
3 L/ R surround speakers (left/right):
Place the rear surround speakers to the
left and right side of your seating position,
either in line with it or slightly behind it.
4 SUBWOOFER (subwoofer):
Place the subwoofer at least one meter
to the left or right of the TV. Leave about
10-centimeter clearance from the wall.
TV
Dock the surround speakers
You can also dock your surround speakers onto
the main unit to listen to audio, for example,
watching TV shows and news.
Connect to TV
Connect this product to a TV. You can listen to
audio from TV programs through the speakers
of this product.
Connect to TV through HDMI (ARC)
Best quality audio
This product supports HDMI with Audio
Return Channel (ARC). If your TV is HDMI
ARC compliant, you can hear the TV audio
through the speakers of this product by using a
single HDMI cable.
1 Using a High Speed HDMI cable, connect
the HDMI OUT (ARC) connector on
the right base speaker to the HDMI ARC
connector on the TV.
• The HDMI ARC connector on the TV
might be labeled differently. For details,
see the TV user manual.
2 On your TV, turn on HDMI-CEC
operations. For details, see the TV user
manual.
Note
If your TV is not HDMI ARC compliant, connect an
•
audio cable to hear the TV audio through the speakers
of this product (see 'Connect audio from TV and other
devices' on page 10).
• If your TV has a DVI connector, you can use an HDMI/
DVI adapter to connect to TV. However, some of the
features may not be available.
Connect audio from TV and other devices
Play audio from TV or other devices through
the speakers of this product.
Use the best quality connection available on this
product, TV, and other devices.
Note
When this product and TV are connected through
•
HDMI ARC, an audio connection is not required.
10
EN
Option 1: Connect audio through a
digital optical cable
Best quality audio
TV
Option 3: Connect audio through
analog audio cables
Basic quality audio
AUDIO OUT
RL
English
1 Using an optical cable, connect the
OPTICAL connector on the right base
speaker of this product to the OPTICAL
OUT connector on the TV or other
device.
• The digital optical connector might be
labeled SPDIF or SPDIF OUT.
Option 2: Connect audio through a
digital coaxial cable
Best quality audio
1 Using a coaxial cable, connect the
COAXIAL connector on the right base
speaker of this product to the COAXIAL/
DIGITAL OUT connector on the TV or
other device.
• The digital coaxial connector might be
labeled DIGITAL AUDIO OUT.
1 Using an analog cable, connect the AUDIO
IN (3.5mm jack) on the right base speaker
of this product to the AUDIO OUT
connectors (red and white) on the TV or
other device.
2 Press once or two times AUX on the
remote control until higher volume is
heard.
EN
11
4 Use your
product
This section helps you use this product to play
audio from connected devices.
Before you start
• Make the necessary connections described
in the quick start guide and the user
manual.
• Switch this product to the correct source
for other devices.
Adjust the volume
1
Press Volume +/- to increase or decrease a
volume level.
• To mute sound, press
• To restore the sound, press
press Volume +/-.
» If volume is set to the maximum or
minimum, the white LED on the right
base speaker blinks two times.
Choose your sound
This section helps you choose the ideal sound
for your video or music.
.
again or
Equalizer
Change the high frequency (treble) and low
frequency (bass) settings of this product.
1 Press TREBLE +/- or BASS +/- to change
the frequency.
» If the treble or bass is set to the
maximum or minimum, the white LED on
the right base speaker blinks two times.
Synchronize video and sound
If the audio and video are not synchronized,
delay the audio to match the video.
1 Press AUDIO SYNC +/- to synchronize
the audio with the video.
• AUDIO SYNC + increases the sound
delay, and AUDIO SYNC - decreases
the sound delay.
» If the value of sound delay is set to the
maximum or minimum, the white LED
on the right base speaker blinks two
times.
Night mode
For quiet listening, night mode decreases the
volume of loud sounds when audio is played.
Night mode is only available for Dolby Digital
soundtracks.
1 Press NIGHT ON/OFF to turn night
mode on or off.
Sound mode
Select predened sound modes to suit your
video or music.
• Press MOVIE to create a surround listening
experience. Ideal for watching movie.
• Press MUSIC to create stereo sound. Ideal
for listening to music.
• Press VOICE to create sound effect
which makes human voice more clear and
outstanding for listening.
12
EN
Play music via Bluetooth
Through Bluetooth, connect your product with
a Bluetooth device (such as an iPad, iPhone,
iPod touch, Android phone, or laptop), and then
you can listen to the audio les stored on the
device through the speakers of this product.
What you need
• A Bluetooth device which supports
Bluetooth prole A2DP, and with Bluetooth
version as 4.1.
• The operational range between the
main unit (left and right speakers) and
a Bluetooth device is approximately
10 meters (30 feet).
1 Press on the remote control to switch
this product to Bluetooth mode.
» The blue LED on the right base
speaker blinks.
2 On the Bluetooth device, switch on
Bluetooth, search for and select Philips
CSS5235Y to start connection (see the
user manual of the Bluetooth device on
how to enable Bluetooth).
» During connection, the blue LED on
the right base speaker blinks.
3 Wait until you hear a beep sound from this
product.
» The blue LED on the right base
speaker lights up.
» If the connection fails, the blue LED on
the right base speaker blinks continually.
4 Select and play audio les or music on
your Bluetooth device.
• During play, if a call is coming, music
play is paused.
• If your Bluetooth device supports
AVRCP prole, on the remote control
you can press
or press
/ to skip to a track,
to pause/resume play.
5 To exit Bluetooth, select other source.
• When your switch back to Bluetooth
mode, Bluetooth connection remains
active.
Play music via NFC
NFC (Near Field Communication) is a
technology that enables short-range wireless
communication between NFC-enabled devices,
such as mobile phones.
What you need
• A Bluetooth device with NFC function.
• For pairing, tap the NFC device on the
NFC tag of this product.
• The operational range between the
main unit (left and right speakers) and a
NFC device is approximately 10 meters
(30 feet).
1 Enable NFC on the Bluetooth device (see
the device' s user manual for details).
2 Tap the NFC device on the NFC tag of
this product until you hear a beep sound
from this product.
» The blue LED on the right base
speaker lights up, and the NFC device
is connected to this product via
Bluetooth.
» If the connection fails, the blue LED on
the right base speaker blinks continually.
3 Select and play audio les or music on
your NFC device.
• To break the connection, tap again the
NFC device with the NFC tag on this
product.
MP3 player
English
Note
The music streaming may be interrupted by obstacles
•
between the device and this product, such as wall,
metallic casing that covers the device, or other devices
nearby that operate in the same frequency.
• If you want to connect this product with another
Bluetooth device, press and hold
control to break the current Bluetooth connection.
on the remote
Connect your MP3 player to play your audio
les or music.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the AUDIO IN
connector on the right base speaker.
EN
13
2 Press the buttons on the MP3 player to
select and play audio les or music.
3 Press once or two times AUX on the
remote control until higher volume is
heard.
• On the MP3 player, it is recommended
to set the volume in the range of 80%
maximum volume.
USB storage devices
Enjoy audio on a USB storage device, such as an
MP3 player and USB ash memory, etc.
What you need
• A USB storage device that is formatted for
FAT or NTFS le systems, and complies
with the Mass Storage Class.
• An MP3 or WMA le on a USB storage
device
1 Connect a USB storage device to this
product.
2 Press USB on the remote control.
3 Use the remote control to control play.
Note
This product supports WMA les which are converted
•
via Windows Media Player (WMA les converted via
other le format converters may not work).
• If a USB storage device has a large media library, it takes
some time to load those contents.
• This product may not be compatible with certain types
of USB storage device.
• If you use a USB extension cable, USB HUB, or USB
multi-reader, the USB storage device may not be
recognized.
• Digital camera PTP and MTP protocols are not
supported.
• Do not remove the USB storage device while it is
being read.
• DRM-protected music les (MP3, WMA) are not
supported.
• Support a USB por t: 5V 1A.
Auto standby
When playing media from a connected device,
this product automatically switches to standby
after 15 minutes of button inactivity and no
audio/video play from a connected device.
Button Action
Start, pause or resume play.
/ Skip to the previous or next track.
USB During play, press to toggle: repeat all
tracks and repeat off.
Repeat play indicator
• If repeat mode is turned on, the
white LED indicator on the main
unit blinks once.
• If repeat mode is turned off, the
white LED indicator on the main
unit blinks twice.
14
EN
Apply factory settings
You can reset this product to the default
settings programmed at the factory.
1 In AUX mode, on the remote control
press Volume -, BASS -, and TREBLE - in
sequence within three seconds.
» When the factory settings restore is
complete, the product automatically
switches off and restarts.
5 Update software
To get the best features and support, update
your product with the latest software.
What you need
• Connect this product to your TV through
HDMI.
Note
Dock the surround speakers onto the main unit (the
•
left and right base speakers), so that the surround
speakers can be upgraded.
Check software version
1
Switch to HDMI ARC mode (press HDMI
ARC).
2 On the remote control, press TREBLE -,
BASS - and Volume - in sequence within
three seconds.
» The current software information is
displayed on the TV screen.
Update software via USB
b Put the "CSS5235.bin" and
"MCU5235.bin" in the root directory
of the USB device.
3 Connect the USB storage device to the
connector on this product.
4 Switch this product to the HDMI ARC
source, and switch your TV to the HDMI
source.
5 On the remote control, within 6 seconds
press
twice, and Volume + once, then
hold down MOVIE.
» If an upgrade media is detected, on the
TV screen you are prompted to start
the update.
» If an upgrade media is not detected,
an error message is displayed on the
TV screen. Make sure that the latest
software of this product is put in the
USB storage device.
6 Press to star t the update.
7 Wait until the update is completed.
» If the update is complete, this product
automatically turns off and on again.
Caution
Do not turn off the power or remove the USB storage
•
device when the software update is in progress because
you might damage this player.
English
1
Check the latest software version on
www.philips.com/support.
• Search for your model and click on
"Software and drivers".
2 Download the software into a USB storage
device.
a Unzip the download if zipped, and
make sure that the unzipped le
contains the following two les.
"CSS5235.bin" (for the software of the
main unit)
"MCU5235.bin" (for the software of
the surround speakers)
EN
15
6 Product
specifications
Note
Specications and design are subject to change without
•
notice.
Amplier
• Total output power:
200W RMS (+/- 0.5 dB, 10% THD)
• Frequency response: 20 Hz-20 kHz / ±3 dB
• Signal-to-noise ratio:
> 65 dB (CCIR) / (A-weighted)
• AUX Input sensitivity:
• 400mV +/- 100mV (connection to an
external device with 3.5mm jack)
• 800mV +/- 100mV (connection to an
external device with red and white
audio jacks)
Audio
• S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
Bluetooth
• Bluetooth proles: A2DP
• Bluetooth version: 4.1
Main unit (left and right base speakers)
• Power supply:
• Model (Philips branded AC power
adapter): DYS602-210309W;
AS650-210-AA309
• Input: 100-240 V~, 50/60 Hz 1.5 A
• Output: 21V
• Standby power consumption: ≤ 0.5 W
• Dimensions (W x H x D):
128 x 221 x 128 mm
, 3.09A
• Weight
• Left base speaker: 1.11 kg
• Right base speaker: 1.29 kg
• Built-in speakers
• 2 x woofer (76.2mm/3", 8 ohm)
• 2 x tweeter (25.4mm/1", 8 ohm)
Surround speakers
• Speaker impedance: 8 ohm
• Speaker drivers: 2 x 63.5 mm (2.5") full
range
• Dimensions (W x H x D):
120 x 117 x 120 mm
• Weight: 0.66 kg/each
Subwoofer
• Power supply: 110-240 V~, 50-60 Hz
• Power consumption: 35 W
• Standby power consumption: ≤ 0.5 W
• Impedance: 3 ohm
• Speaker drivers:
1 x 133 mm (5.25") woofer
• Dimensions (W x H x D):
226 x 251 x 306 mm
• Weight: 4.0 kg
Remote control batteries
• 1 x AAA-R03-1.5 V
Standby power management
• When the product remains inactive for
15 minutes, it automatically switches to
standby or networked standby.
• The power consumption in standby or
networked standby is less than 0.5W.
• To deactivate Bluetooth connection, press
and hold the Bluetooth button on the
remote control.
• To activate Bluetooth connection, enable
Bluetooth connection on your Bluetooth
device, or enable Bluetooth connection via
the NFC tag (if available).
16
EN
7 Troubleshooting
Warning
•
Risk of electric shock. Never remove the casing of the
product.
Distorted sound or echo.
• If you play audio from the TV through this
product, make sure that the TV is muted.
Audio and video are not synchronized.
• Press AUDIO SYNC +/- to synchronize
the audio with the video.
English
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at
www.philips.com/support.
Main unit
The buttons on this product do not work.
• Disconnect this product from the power
supply for a few minutes, then reconnect.
Sound
No sound from the speakers of this product.
• Connect the audio cable from this product
to your TV or other devices. However, you
do not need a separate audio connection
when this product and TV are connected
through HDMI ARC connection.
• Reset this product to its factory settings.
• On the remote control, select the correct
audio input.
• Make sure that this product is not muted.
No sound from the wireless surround
speakers.
• Wirelessly connect the speakers to the
main unit.
• Dock the wireless surround speakers into
the main unit to charge the battery.
No sound from the wireless subwoofer.
• Wirelessly connect the subwoofer to the
main unit.
Bluetooth
A device cannot connect with this product.
• The device does not support the
compatible proles required for this
product.
• You have not enabled the Bluetooth
function of the device. See the user manual
of the device on how to enable the
function.
• The device is not correctly connected.
Connect the device correctly.
• This product is already connected with
another Bluetooth device. Disconnect the
connected device, then try again.
Quality of audio play from a connected
Bluetooth device is poor.
• The Bluetooth reception is poor. Move the
device closer to this product, or remove
any obstacle between the device and this
product.
The connected Bluetooth device connects and
disconnects constantly.
• The Bluetooth reception is poor. Move the
device closer to this product, or remove
any obstacle between the device and this
product.
• Turn off Wi-Fi function on the Bluetooth
device to avoid interference.
• For some Bluetooth, the Bluetooth
connection can be deactivated
automatically to save power. This does not
indicate any malfunction of this product.
EN
17
NFC
A device cannot connect with this product via
NFC.
• Make sure that the device is supported by
NFC.
• Make sure that NFC is enabled on the
device (see the device' s user manual for
details).
• For pairing, tap the NFC device on the
NFC tag of this product.
18
EN
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, & DTS and the
Symbol together are registered trademarks, and
DTS Digital Surround is a trademark of DTS,
Inc. © DTS, Inc. All Rights Reserved.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the
double-D symbol are trademarks of Dolby
Laboratories.
The terms HDMI and HDMI High-Denition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
is under license. Other trademarks and trade
names are those of their respective owners.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.
19
Specications are subject to change without notice
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and
Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V.
CSS5235Y_12_UM_V2.0
Loading...