Always there to help you
Register your product and get support at
www.philips.com/support
Question?
Contact
Philips
CEM2300BT
User manual
Contents
1 Safety 2
2 Your car audio system 3
Introduction 3
What's in the box 3
Overview of the system 4
3 Install the car audio system 6
Connect wires 7
Mount into the dashboard 7
Attach the front panel 9
4 Get started 10
For the rst time use 10
Set the time format 10
Set the clock 10
Turn on 10
Switch music listening zone 10
Mute the button beep 10
5 Listen to radio 11
Tune to a radio station 11
Store radio stations in memory 11
Tune to a preset station 11
Play with RDS 11
10 Adjust sound 18
11 Adjust system settings 18
12 Others 19
Reset 19
Replace fuse 19
13 Product information 20
14 Troubleshooting 21
General 21
About the Bluetooth device 21
15 Notice 22
Compliance 22
Care of the environment 22
Trademark notice 23
Copyright 23
6 Play from hard media 13
Play a disc 13
Play from a USB storage device 14
7 Use Bluetooth devices 15
Connect a device 15
Play audio from a Bluetooth device 16
Make a call 16
8 Listen to an external player 17
9 Charge your USB device 17
1EN
1 Safety
Read and understand all instructions before
you use your apparatus. If damage is caused by
failure to follow instructions, the warranty does
not apply.
• This apparatus is designed for negative
ground (earth) 12 V DC operation only.
• To ensure safe driving, adjust the volume to
a safe and comfortable level.
• Improper fuses can cause damage or
re. When you need to change the fuse,
consult a professional.
• Use only the supplied mounting hardware
for a safe and secure installation.
• To avoid short circuit, do not expose the
apparatus to rain or water.
• Never insert objects into the ventilation
slots or other openings on the apparatus.
• Clean the apparatus and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the apparatus.
• Never place any objects other than discs
into the apparatus.
• Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
• Visible and invisible laser radiation when
open. Avoid exposure to beam.
Caution
Use of controls or adjustments or performance of
•
procedures other than herein may result in hazardous
laser exposure or other unsafe operation.
• The apparatus shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
apparatus (e.g. liquid lled objects, lighted
candles).
2 EN
2 Your car audio
df
system
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
• Unsupported les:
AAC, WAV, and PCM les
DRM protected WMA les (.wav, .m4a,
.m4p, .mp4, and .aac)
WMA les in lossless format
What's in the box
Check and identify the contents of your
package:
Introduction
With the in-car audio system, you can listen to
• FM or AM (MW) radio,
• Audio from a CD or MP3 disc,
• Audio from a USB storage device,
• Audio from a Bluetooth device, and
• Audio from an external player.
Playable media:
• Disc
• Audio CD, MP3-CD, WMA-CD
• CD-R, CD-RW
• USB storage device
• Compatibility: USB 2.0, USB 1.1
• Class support: MSC (Mass Storage
Class)
• Maximum capacity: 32 GB
• Files
• File system: FAT16, FAT32
• Maximum number of folders: 99
• Maximum number of tracks/les: 999
• Maximum level of directory: 8
• .mp3 les
Sampling frequencies: 32 kHz, 44.1 kHz,
48 kHz
Bitrates: 8-320 kbps and variable
bitrates
• .wma les
Versions: V4, V7, V8, V9 (L1 and L2)
Sampling frequencies: 44.1 kHz, 48 kHz
Bitrates: 64-192 kbps and variable
bitrates
• ID3 tag V2.0 or later
abc
e
a Main unit (with a sleeve)
b Carrying case (with the front panel
included)
c Trim plate
d Disassembly tool x 2
e Rubber cushion
f Screw x 1
g User manual
g
3EN
Overview of the system
ab cdef
ts rqpo nmlkji ghuv
w
a
• Unlock the front panel.
b
• Press to return to the previous menu.
• Press and hold to access the system
menu.
c
• For .wma and .mp3 tracks, press to
select the previous folder.
• In radio mode, press to select a tuner
band.
• Press and hold to activate the selection
of listening zones.
4 EN
d Disc slot
e LCD screen
f
• Eject the disc from the disc
compartment.
g
• Connect to a USB storage device.
h AUDIO IN
• Connect to the audio output socket
(usually the headphone socket) of an
external device.
i
• Start, pause, or resume the play of
tracks.
• In radio mode, press to select the
preset radio station of No. 6.
• In radio mode, press and hold to store
the current radio station at channel
No. 6 .
j
• In radio mode, press to select the
preset radio station of No. 5.
• In radio mode, press and hold to store
the current radio station at channel
No. 5.
k
• In radio mode, press to select the
preset radio station of No. 4.
• In radio mode, press and hold to store
the current radio station at channel
No. 4.
• For .wma and .mp3 tracks, press
repeatedly to select a play mode: play
all tracks randomly ([SHU ALL]), play
tracks in the current folder randomly
([SHU FLD]), or play all tracks in the
storage device in sequence ([SHU
OFF]).
l
• In radio mode, press to select the
preset radio station of No. 3.
• In radio mode, press and hold to store
the current radio station at channel
No. 3.
• For .wma and .mp3 tracks, press
repeatedly to select a repeat mode:
repeat the current track ([REP ONE]) ,
repeat all tracks in the current folder
([RPT FLD]), or repeat all tracks in the
storage device ([RPT ALL]).
m
• In radio mode, press to select the
preset radio station of No. 2.
• In radio mode, press and hold to store
the current radio station at channel
No. 2.
• For .wma and .mp3 tracks, press to
access the folder list.
n
• In radio mode, press to select the
preset radio station of No. 1.
• In radio mode, press and hold to store
the current radio station at channel
No. 1.
• For .wma and .mp3 tracks, press to
access the track list.
o
/DISP
• Press repeatedly to display available
information about the current track.
• Press repeatedly to display available
RDS information.
• Press and hold to display the set clock.
p AS/SOURCE
• Press repeatedly to select a source.
• In radio mode, press and hold to
activate the automatic search of radio
stations.
q
• Press and hold to enable or disable
the DBB (dynamic bass boost) sound
effect.
• For .wma and .mp3 tracks, press to
select the next folder.
• In radio mode, press to select a tuner
band.
r
• Press to turn on the system.
• Press and hold to turn off the system.
• Press to mute the speakers or release
them from mute status.
• Press to conrm an option.
• Rotate to switch between menu
options.
• Rotate to adjust the volume level.
s
• Press repeatedly to select a preset
sound equalizer.
• Press and hold to activate the setup of
bass, treble, balance, and fader.
5EN
t /
• Tune to a radio station.
• Press to skip to the previous or next
track.
• Press and hold to rewind a track or
search fast forward.
u
• Press to hang up an ongoing call.
• When there is an incoming call, press
to reject it.
• When it is not in a call, press to enable
or disable the MAX Sound feature.
v
• When there is an incoming call, press
to answer.
• Press and hold to redial the last called
number.
• In a call, press and hold to transfer the
voice between the phone and the car
speakers.
w RESET
• Press to reset the system to factory
default settings.
3 Install the car
audio system
Caution
Use the controls only as stated in this user manual.
•
Always follow the instructions in this chapter in
sequence.
These instructions are for a typical installation.
However, if your car has different requirements,
make the adjustment accordingly. If you have
any question regarding installation kits, consult
your local retailer.
Note
This system is designed for negative ground (earth) 12V
•
DC operation only.
• Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system
heats up during use.
• To avoid short-circuit: before you connect, make sure
that the ignition is off.
• Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
• Make sure that all loose leads are insulated with
electrical tape.
• Make sure that the leads do not get caught under
screws or iron parts that will move (e.g. seat rail).
• Make sure that all ground (earth) leads are run to a
common ground (earth) point.
• Use only the supplied mounting hardware for a safe
and secure installation.
• Improper fuses can cause damage or re. When you
need to change the fuse, consult a professional.
• When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
• Never connect speaker wires to the metal body or
chassis of the car.
• Never connect speaker wires with stripes to one
another.
6 EN
Loading...