Philips CEM220X/78, CEM220/55 Quick Installation Guide
Register your product and get support at
CEM220/55
EN Installation Guide
1
ab
efg
c
d
34
2
A1A2 A3A4 A5A6A7 A8
B1 B2 B3 B4 B5B6 B7 B8
A
A
B
abcd
B
b
a
c
d
aa
b
c
d
a
b
e
f
c
d
g
h
i
b
c
d
Overview of parts
1
These are the supplied parts needed to
connect and install this unit.
1 In-car audio system
2 Sleeve
3 Front panel
4 Trim plate
5 Rubber cushion
6 Disassembly tools
7 Screws 4 pieces
Connect wires
Caution
Ensure that all loose leads are insulated with
electrical tape.
•
For cars with ISO connectors
2 3
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied
standard connector to the unit.
3
Connect the antenna and amplifi er as
illustrated, if applicable.
Connector Connect to
1 REAR LINE OUT R Rear right
speaker
2 REAR LINE OUT L Rear left speaker
3 SUB OUT Subwoofer
4 ANTENNA Antenna
For cars with ISO connectors
3 4
Caution
Be sure to connect the black ground (earth)
lead fi rst.
•
1
Connect the antenna and amplifi er as
illustrated, if applicable.
2
Cut off the bigger end of the supplied stan-
dard connector.
3
Check the car’s wiring carefully and connect
them to the supplied standard connector.
4
Connect the supplied standard connector to
the unit.
1 Green/black
strip
Left speaker
(Rear)
2 White/black
strip
Left speaker
(Front)
3 Gray/black
strip
Right speaker
(Front)
4 Purple/black
strip
Right speaker
(Rear)
e RED Ignition key +12V DC
when ON/ACC
f BLUE Motor/electric antenna
relay control lead/
Amplifi er relay control
lead
g BLACK Ground
h Or ange/
white
Illumination switch
i YELLOW To the +12V car battery
which is energized at all
times
Attach the front panel 5
1
Insert the right side of the panel in the
chassis until it is correctly engaged.
2
Press the left side of the panel and point
the left hole at the left pillar.
3
Release the panel to engage the left side.
4
Attach the trim plate.
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in a car
that has an on-board drive or navigation
computer, the computer may lose its
memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Remove the two screws on the top of the
unit.
3
Remove the mounting sleeve with the
supplied disassembly tools.
4
Ensure that car dashboard opening is
within these measurements:
•
•
5
Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
6
Place the rubber cushion over the end of
the bolt.
7
Slide the unit into the dashboard until you
hear a click sound.
8
Reconnect the negative terminal of the car
battery.
Turn on
1
Press z to turn on the unit.
To turn off the unit, press zfor 3
seconds.
Set clock
1
Press MENU/DISP for 3 seconds.
2
Press 3 or4 repeatedly to until the cur-
rently time is displayed.
3
Tur n z clockwise to set hour.
4
Press z to confi rm.
5
Tur n z anti-clockwise to set minute.
6
Press z to confi rm.
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1
Press SOURCE repeatedly to select Tuner.
2
Press or to select band: [FM1],[FM2],
[FM3], [AM1], or [AM2] .
3
Press∞or§to tune to a radio station
manually.
To search for a radio station
automatically, press SEARCH.
•
•
Play audio fi les
1
Press on the front panel to release the
panel.
2
Insert a CD with the printed side facing up.
3
Close the panel.
4
Press
2;
, to start play.
To pause CD play, press
2;
.
To resume CD play, press 2; again.
Insert the USB device
1
Open the cover marked on the front
panel.
2
Insert the USB device into the USB socket.
»
ToThe unit starts playing from the USB
device automatically.
•
•
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
5
4.75-5.56 mm
Loading...