Philips CDR600-602 Service Manual

CHANGE IN COURSE OF PRODUCTION

From production week 0127 onwards the Power Supply Unit (pos. 1003) has been changed from
“PSU-CDR3-ECO” to “SMPS CDR785”.

Sets with the new Power Supply Unit can be identified by factory change code VN020127... or higher.
The complete boards can be ordered with following code numbers:

3103 308 52960 SMPS CDR785 EU /00
3103 308 52970 SMPS CDR785 US /17

To adapt the set to the new Power Supply following additional changes were implemented:

- support frame pos. 184 added → see new Exploded View attached to this Service Information

- 4,7kΩ resistor soldered on Power Supply Board between pin 1 and 2 of connector 1

- cables 8002 and 8006 replaced by a special Y-cable 8010 → see new Wiring Diagram attached to this Service
Information

NOTE: In case of a failure the new Power Supply Units are intended to be replaced completely.

For orientation block diagrams, schematic diagrams and assembly drawings are attached to this Service
Information.

In CDR600/00 the European version “SMPS CDR785 EU /00” and the World Wide version
“SMPS CDR785 WW /01” of the Power Supply Unit will be used alternatively.
For Service it is recommended always to replace by the European version.

Service will deliver the new Power Supply Units without the 4,7kΩ resistor soldered on the board.
When the unit has to be exchanged the resistor has to be soldered onto the new board.

Service Information

SSeerrvviiccee
SSeerrvviiccee

Service

Product Service Group CE Audio

Compact Disc Recorder CDR600, CDR602

A01-350

©

3103 785 25120

2001-06-30

Already published Service Information: none

Mechanical Instructions

GB 25-1

4

CDR600

8010

3103 308 9287

2 pole

8 pole

9 pole

grey

green

8001

3104 157 1124

Connections delivered
with CDR-loader assy

Cable connected
to tray switch and
tray motor

8003

3104 157 10982

3104 128 0599

I/O BOARD

3104 128 0585

MAIN BOARD CDR

POWER SUPPLY UNIT

1400

114

1500

11

F934

110

CON1

CON2

1000

1220

1330

1200

1

10

1

11

Flex connected
to CDM

Flex connected
to sledge motor

Flex connected
to turn table motor

1

4

130

114

1

0101

1 7

1

11

ON/OFF & STBY LED

3104 128 0589

8009

3104 157 11271

8010 (special Y cable)

at conn.1500

CDR Module

at conn.1

PSU

at conn.1301
on/off switch

1 VDC2

VFTD2

3 VDC1
4

NC
+5V

GROUND
5
6
7 GROUND

GROUND

NC

8
9
10 +12V

-8V11

1 ON/OFF

NC (5V ever)2

1 ON/OFF

GROUND2

3 -F
4

-30V
+5V

+F
5
6
7 GROUND

GROUND

NC

8
9
10 +12V

-8V11

8003 (at conn. F934
of CDR main board)

1 VDC2
2 VFTD
3 VDC1
4 SYS_RESET
5IIC_DATA
6 GROUND
7IIC_CLK
8 DISPL_INT
9 GROUND
10 D5V

8004

1 LEFT_HP_OUT
2 GROUND
3 RIGHT_HP_OUT

8001 (at conn. 1400
of CDR main board)

1 GROUND
2 DIG_OUT_C
3 GROUND
4 EXT_DIG_IN
5 EXT_OPT_IN
6 GROUND
7D5V
8KILL
9LEFT_IN
10 GROUND
11 RIGHT_IN
12 RIGHT_OUT
13 GROUND
14 LEFT_OUT

Pin 1 indicated by All Wires are 1/1, except flex 8001 and 8010

8008

1LED_ON
2 GROUND

TO FRAME

8008

3104 157 11261

3104 128 0589

DISPLAY BOARD

1410

13

1119

1

1

10

8004

3104 157 11002

TO FRAME

1301

1300

HEADPHONE/IR BOARD

3104 128 0589

3

13

31

12

1121

1122

1200

1201

1000

Texture indicates text on flex.

12

1

2

CDR600 with CDR785 PSU, 130601

8009

1+5V
2 IR_IN
3 GROUND

grey

green

3103 308 54210 PSU CDR600/00

(3103 308 52960 CDR785/00 + 4,7kΩ soldered between pin 1 and 2 of CON1

or

3103 308 52980 CDR785/01 + 4,7kΩ soldered between pin 1 and 2 of CON1)

3103 308 54220 PSU CDR600/17

(3103 308 52970 CDR785/17 + 4,7kΩ soldered between pin 1 and 2 of CON1)

pin 1 = grey wire

not

used

WIRING DIAGRAM

Power Supply Unit

SMPS CDR785

Mechanical Instructions

GB 26-1

4

CDR600

EV CDR600 SMPS CDR785, 130601

DISPLAY ASSY

MAIN BOARD CDR

LOADER ASSY

CDL4009/51

CDR770-LOADER MODULE

SUSPENSION

POWER SUPPLY UNIT

ON/OFF&STBY LED

HEADPHONE/

IR BOARD

DISPLAY BOARD

76+77+78+79+81+82+
85+86+1001

I/O BOARD

Pl. Torx

3x10

Pl. Torx

3x10

Pl. Torx

3x10

Pl. Torx

3x10

Torx

M3x6

Torx

M3x6

Torx

M3x6

Torx

M3x6

Torx

M3x6

Torx

M3x6

Filter FTD

1005

97 98

40

41

99 100

Pl. Torx

3x10

Torx

M3x15

Torx

M3x6

Pl. Torx

3x10

2x

184

185

for /00:

SMPS CDR785 EU /00

or

SMPS CDR785 WW /01

for /17:

SMPS CDR785 US /17

+ 4,7kΩ soldered between

pin 1 and 2 of con 1

301

xxx

312

2x

317

318

76 77 78 79

Service part

xxx

no Service part

RC282921/01

800

1

EXPLODED VIEW

Power Supply Unit

SMPS CDR785