|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CBTS3257 |
INTEGRATED CIRCUITS |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CBTS3257
Quad 1-of-2 multiplexer/demultiplexer with Schottky diode
Product data |
2002 Sep 27 |
P s
on o s
Philips Semiconductors |
Product data |
|
|
|
|
|
|
|
Quad 1-of-2 multiplexer/demultiplexer
CBTS3257
with Schottky diode
FEATURES
•5 Ω switch connection between two ports
•TTL-compatible input levels
•Schottky diodes on I/O clamp undershoot
•Minimal propagation delay through the switch
•Latch-up protection exceeds 500 mA per JESD78
•ESD protection exceeds 2000 V HBM per JESD22-A114,
200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101
DESCRIPTION
The CBTS3257 is a quad 1-of-2 high-speed TTL-compatible multiplexer/demultiplexer. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise.
Output Enable (OE) and select-control (S) inputs select the appropriate B1 and B2 outputs for the A-input data.
Internal Schottky diode provides I/O undershoot protection.
The CBTS3257 is characterized for operation from ±40 to +85 °C.
PIN CONFIGURATION
|
|
|
|
|
VCC |
|
S |
1 |
|
16 |
|
||
|
|
|
|
|
|
|
1B1 |
2 |
|
15 |
|
OE |
|
|
|
|
|
|
|
|
1B2 |
3 |
|
14 |
|
4B1 |
|
|
|
|
|
|
|
|
1A |
4 |
|
13 |
|
4B2 |
|
|
|
|
|
|
|
|
2B1 |
5 |
|
12 |
|
4A |
|
|
|
|
|
|
|
|
2B2 |
6 |
|
11 |
|
3B1 |
|
|
|
|
|
|
|
|
2A |
7 |
|
10 |
|
3B2 |
|
|
|
|
|
|
|
|
GND |
8 |
|
9 |
|
3A |
|
|
|
SA00533 |
||||
|
|
|
|
|
|
|
PIN DESCRIPTION
PIN NUMBER |
SYMBOL |
NAME AND FUNCTION |
|||
|
|
|
|
|
|
1 |
|
S |
Select-control input |
||
|
|
|
|
|
|
2, 3, |
1B1, 1B2, |
|
|||
5, 6, |
2B1, 2B2 |
B outputs |
|||
10, 11, |
3B1, 3B2 |
||||
|
|||||
13, 14 |
4B1, 4B2 |
|
|||
|
|
|
|
|
|
4, 7, 9, 12 |
1A, 2A, 3A, 4A |
A inputs |
|||
|
|
|
|
|
|
8 |
GND |
Ground (0 V) |
|||
|
|
|
|
|
|
15 |
|
|
|
Output enable |
|
|
OE |
||||
16 |
VCC |
Positive supply voltage |
ORDERING INFORMATION
PACKAGES |
TEMPERATURE RANGE |
ORDER CODE |
TOPSIDE MARK |
DWG NUMBER |
|
|
|
|
|
16-pin plastic SO |
±40 to 85 °C |
CBTS3257D |
CBTS3257D |
SOT109-1 |
|
|
|
|
|
16-pin plastic SSOP |
±40 to 85 °C |
CBTS3257DB |
CS3257 |
SOT338-1 |
|
|
|
|
|
16-pin plastic SSOP (QSOP) |
±40 to 85 °C |
CBTS3257DS |
CBS3257 |
SOT519-1 |
|
|
|
|
|
16-pin plastic TSSOP |
±40 to 85 °C |
CBTS3257PW |
CBS3257 |
SOT403-1 |
|
|
|
|
|
Standard packing quantities and other packaging data is available at www.philipslogic.com/packaging.
2002 Sep 27 |
2 |
Philips Semiconductors |
Product data |
||
|
|
|
|
Quad 1-of-2 multiplexer/demultiplexer |
CBTS3257 |
||
with Schottky diode |
|||
|
|
||
|
|
|
LOGIC DIAGRAM (positive logic)
4 |
2 |
1A |
1B1 |
|
3 |
|
1B2 |
7 |
5 |
2A |
2B1 |
|
6 |
|
2B2 |
9 |
11 |
3A |
3B1 |
|
10 |
|
3B2 |
12 |
14 |
4A |
4B1 |
|
13 |
|
4B2 |
1
S
15
OE
FUNCTION TABLE
|
|
INPUTS |
FUNCTION |
|
|
|
|
|
|
|
OE |
|
S |
|
|
L |
|
L |
A port = B1 port |
|
|
|
|
|
|
L |
|
H |
A port = B2 port |
|
|
|
|
|
|
H |
|
X |
Disconnect |
|
|
|
|
|
SA00532
2002 Sep 27 |
3 |
Philips Semiconductors Product data
Quad 1-of-2 multiplexer/demultiplexer |
|
|
CBTS3257 |
||||
with Schottky diode |
|
|
|||||
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
ABSOLUTE MAXIMUM RATINGS1 |
|
|
|
|
|
||
SYMBOL |
PARAMETER |
|
CONDITIONS |
RATING |
|
UNIT |
|
|
|
|
|
|
|
|
|
VCC |
DC supply voltage |
|
|
±0.5 to +7.0 |
|
V |
|
VI |
DC input voltage2 |
|
|
±0.5 to +7.0 |
|
V |
|
|
Continuous channel current |
|
|
128 |
|
mA |
|
|
|
|
|
|
|
|
|
IK |
Input clamp current |
|
VI/O < 0 |
±50 |
|
mA |
|
Tstg |
Storage temperature range |
|
|
±65 to +150 |
|
°C |
|
NOTES:
1.Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under ªrecommended operating conditionsº is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
2.The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
RECOMMENDED OPERATING CONDITIONS
SYMBOL |
PARAMETER |
|
LIMITS |
UNIT |
|
|
|
|
|||
MIN |
|
MAX |
|||
|
|
|
|
||
|
|
|
|
|
|
VCC |
DC supply voltage |
4.5 |
|
5.5 |
V |
VIH |
High-level input voltage |
2.0 |
|
Ð |
V |
VIL |
Low-level Input voltage |
Ð |
|
0.8 |
V |
Tamb |
Operating free-air temperature range |
±40 |
|
+85 |
°C |
NOTE: |
|
|
|
|
|
1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation.
DC ELECTRICAL CHARACTERISTICS
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LIMITS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
SYMBOL |
PARAMETER |
|
TEST CONDITIONS |
Tamb = ±40 to +85 °C |
UNIT |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
MIN |
TYP1 |
MAX |
|
|
VIK |
Input clamp voltage |
A or B inputs |
VCC = 4.5 V; II = ±18 mA |
Ð |
Ð |
±0.8 |
V |
||||||||||
|
|
|
|
|
|
||||||||||||
Control inputs |
Ð |
Ð |
±1.2 |
V |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|||||||
VP |
Pass voltage |
VI = VCC = 5.0 V; I/O = ±100 mA |
3.4 |
3.6 |
3.9 |
V |
|||||||||||
|
II |
|
Input leakage current |
VCC = 5.5 V; VI = GND or 5.5 V |
Ð |
Ð |
±1 |
μA |
|||||||||
ICC |
Quiescent supply current |
VCC = 5.5 V; IO = 0, VI = VCC or GND |
Ð |
Ð |
3 |
μA |
|||||||||||
|
I |
|
Additional supply current per input pin2 |
VCC = 5.5 V, one input at 3.4 V, |
Ð |
Ð |
2.5 |
mA |
|||||||||
|
CC |
|
|
|
other inputs at VCC or GND |
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
||||||||
|
CI |
Control pins capacitance |
VI= 3 V or 0 |
|
|
|
|
|
Ð |
3.3 |
Ð |
pF |
|||||
CIO(OFF) |
Off capacitance |
A port |
VO = 3 V or 0; |
OE |
= VCC |
Ð |
9.9 |
Ð |
pF |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
||||||
B port |
VO = 3 V or 0; OE = VCC |
Ð |
6.4 |
Ð |
pF |
||||||||||||
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
VCC = 4.5 V; VI = 0V; II = 64 mA |
Ð |
5 |
7 |
Ω |
|||||||
r |
on |
3 |
On-resistance |
V |
= 4.5 V; V |
I |
= 0V; I |
I |
= 30 mA |
Ð |
5 |
7 |
Ω |
||||
|
|
|
|
|
CC |
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
VCC = 4.5 V; VI = 2.4 V; II = 15 mA |
Ð |
10 |
15 |
Ω |
NOTES:
1.All typical values are at VCC = 5 V, Tamb = 25 °C.
2.This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND
3.Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. On-state resistance is determined by the lowest voltage of the two (A or B) terminals.
2002 Sep 27 |
4 |