Philips BG2028-42 User Manual

ENGLISH

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electric appliance, basic precau tions should always be followed, including the following;

Read all instructions before using this

appliance.

DANGER

To reduce the risk of electric shock:

1. Do not reach for a charging stand while plugged in that has fallen into water. Unplug immediately.

2. Power plug and the accessories connected to it are not for immersion or for use in shower.

3. Do not use an extension cord with this appliance.

4. Do not place or store charging stand where it can fell or be pulled into a tub or sink. Do not place or drop a charging stand into water or other liquid while plugged in.

5. Always unplug the charging stand from the electrical outlet immediate^ use. except when groomer is (re)charging.

6. Remove power supply cord from charging stand before cleaning.

7. When discarding groomer, unplug charging stand and remove groomer from charging stand before removing rechargeable batteries. See Battery Removal instructions.

WARNING

To reduce the risk of burns, fire, electric shock or injury to persons:

1. Close supervision is necessary when this groomer/charging stand is used by. on, or near children or invalids.

2. Use this groomer/charging stand for its intended household use as described in this manual. Do not use attachments not recommended by Philips Electronics North America Corporation.

3. This appliance is only intended for shaving and trimming body parts below the neckline. Do not use it to shave or trim facial or scalp hair.

4. Never operate this groomer/charging stand if it has a damaged cord or charging plug, if it is not working properly, if it has teen dropped or damaged, or dropped into vvater. For assistance cairi.800-243-i050.

5. Keep the groomer, charging stand, cord and charging (xug away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Never operate the groomer with the air openings blocked or while on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint. hair, and the lite.

8. Do not operate, charge or plug in groomer outdoors or where aerosol (spray) products are being used or where oxygen is being administered.

9. Always check foil, cutters, and trimmers before using the groomer. Do not use the groomer if foil, cutters or trimmers are damaged, as injury may occur.

10. Always attach plug to charging stand first then charging plug into outlet To disconnect remove charging plug from outlet

11 Use only the cord and charging stand

provided to charge and (re)charge the groomer.

12. n the appliance is subjected to a major change in temperature, pressure or humidity, let the appliance acclimatize for 30 minutes before using.

13. Never put the groomer/charging stand in direct sunlight or store at a temperature above 140*r.

14. Groomer is water-safe and can be rinsed under running cap water or used in shower. Do not submerge groomer in water.

15. To prevent possible damage to the cord, do not wrap cord around the charging stand. Do not store in a damp environment.

16. Only use the power plug and other accessories supplied with the groomer.

SAVETHESE

INSTRUCTIONS

IMPORTANT: The power plug contains a transformer. Do not cut off the power plug to replace it with another plug, as this will cause a hazardous condition.

Registration

Congratulations on your purchase and welcome to Philips Norelco!

To fully benefit from the support that Philips

Norelco offers, register your product at vAvw.norelco.com/register

Create Your Own Look

Your new Philips Norcko Bodygroom system offers you a safe, gentle and quick way to trim and shave every body part below the neckline. This unique combination allows you to create your own look safely and with less irritation. The trimming unit gives you multiple trimming combs to choose from so you can control the exact hair length you desire or use the shaving unit to completely shave off body hair Use wet or dry. your Bodygroom system with self-sharpening blades will give you a precise trim and shave anywhere, every time.

Like many r>ew products, your Philips Norelco Bodygroom may take a little getting used to. If you are shaving sensitive areas for the first time, your skin may need time to adapt Give yourself some lime to acquaint yourself with your new Bodygroom. If you are still not convinced. Philips Norelco will refund you the full purchase price as long as the request is received within 45 days of purchase.

Stick with it! If you alternate trimming or shaving methods during the adjustment period it may make it more difficult to adapt to the Philips Norelco Bodygroom system.

Features

A Trimming Comb 1 (1/8 inch/3mm)

B Trimming Comb 2 (3/16 inch/Smm)

C Trimming Comb 3 (9/32 inch/7mm)

D Shaving Head E On/Off Button F Battery Status Indicator

G Adapter

H Cleaning Brush I Charging Stand

J Comb Size Indicator

Full Two-Year Warranty 45-Day Money-Back Guarantee

This symbol indicates that the groomer can be used in the bath or shower.

Battery Status Indicator

I The Battery Status Indicator on the Groomer

will flash green to indicate Groomer is (re)charging.

> After approximately 8 hours the Battery Status

Indicator lights up continuously to indicate the Groomer is fully charged.

t After Groomer is fully charged, the Battery

Status Indicator goes out after 30 minutes to save energy.

Before First Use

> Charge the Groomer before you start using

it (see 'Charging'). Make sure the Groomer is switched off before you start charging it.

t Before using, check foil, cutters, trimmers and

combs for wear or damage. If foil, cutters, trimmers or combs show signs of wear or damage, do not use Groomer as injury may occur. Do not use Groomer until foil, cutters, trimmers or combs have been replaced.

Important

t Only use the power cord provided to charge

the Groomer.

Charging

> Chargif^ requires 8 hours. > Use only the power cord and charging stand

provided.

№ Battery performance is test if you recharge

only when the batteries are completely empty.

№ Charging, recharging or storing at temperatures

below 40®F or higher than 95®F adversely affects lifetime of batteries.

I The Groomer can only be charged in the

charging stand.

□ Be certain Groomer is OFF. □ Connect power cord to chargng stand (Fig. 1). Q Plug the adaptor into any 120V AC outlet.

Use only the power cord provided.

I An adaptor plug may be necessary for power

cord usage in some foreign countries. Use an attachment F^ug adaptor of the proper configuration for the power outlet.

□ Put the Groomer in the charging stand

(Fig. 2). Make sure the charging contacts on front side of the Groomer fit into the charing stand correctly. When placed correctly, the Battery Status Indicator will flash green to indicate the Groomer is (re)chargif^ (Fig. 3).

H A fully charged Groomer has a cordless

grooming time of up to 50 minutes.

Features

□ When the battery is fully charged, the

Battery Status Indicator lights up green continuously (Fig. 4).

D Disconnect the power cord and unplug from

the electrical outlet

Optimize The Working Life of The Battery I After Groomer has been charged for the first

time, do not recharge Groomer betv/een grooming sessions. Continue using it until the battery is completely empty.

I Discharge the battery completely twice a

year by letting the motor run until it stops.

t Do not keep plug permanently plugged in.

Recharging

Recharge when the Battery Status Indicator flashes orange. This indicates there is approximately 10 minutes of operating time lefL

If the Battery Status Irxlicalor Hashes orange quickly, the battery is completely empty. Charge the Groomer before using.

B When Groomer is fully charged, disconnect

the charging plug from outlet.

Trimming

i Use this Groomer for its intended household

use as described in this manual.

i The Groomer comes with 3 trimming combs

to cut hair to 3 different lengths.

I If you are trimming for the first time, be

careful. Do not move the Groomer too fast. Make smooth and gentle movements.

> Practice trimming with the trimming comb 3

first to prevent accidentally trimming hairs too short.

i Trimming is easier and more effective when

skin and hair are dry.

Q Snap the desired trimming comb onto

Groomer. Make sure the teeth of the comb point in the direction you will move the appliance (Fig. 5).

When you move the Groomer towards you.

the teeth should point toward you (Fig. 6).

When you move the Groomer away from you. the teeth should point away from you (Fig. 7).

Trimming Length Setting Table I The comb size (1.2 or 3) is indicated on the

back of each comb.

Trimming Comb Hair length after trimming

1 1/8 in. / 3 mm 2 3

Turn Groomer ON by pressing the on/off

button (Fig. 8).

Move Groomer against the direction of hair growth ntaking sure the tips of the comb point in the same direction as you are moving the Groomer. Always make smooth and gentle rrtovements and be sure the surface of the comb always stays in contact with your skin.

NOTE: Since all hairs do not grow in the same direction, you nviy want to try different trimming positions (i.e. upwards, downwards, or across). Praake is best for optimum results.

□ Turn Groomer OFF by pressing the on/off

button.

Shaving

I Do not use this Groomer to shave or trim

facial or scalp hair. The Groomer should only be used on skin below the neckline.

I WHien shaving sensitive areas for the first time,

you may feel some discomfort, irritation or reddening of the skin. This is normal as your skin needs time to adjust to shaving.

3/16 in. / 5 mm 9/32 in. / 7 mm

I If your hair is l^ger than 13/32 in. / 10 mm.

trim hair usir^ trimmer comb 1 to a length of 1/8 in73mm first for optimum shavir^ results.

I For dry use. be certain that your skin is clean

and dry before using the Groomer.

I For wet use. you may prepare your skin with

lathered soap or shaving foam before using the Groomer.

I Make sure the shaving foil is in complete

contact with your skin for the closest shave and minimum foil wear.

I Pressing too hard may cause skin irritations.

I Practice is best for optimum results.

Remove any trimming comb from Groomer

(Fig. 9).

Turn Groomer ON by pressing the on/off button (Fig. 8).

Stretch your skin taut with your free hand and gently press Groomer to skin and move it slovdy and smoothly against the direction

of hair growth. DO NOT press too hard.Too much pressure can distort the foil and cause skin irritation.

TIP: Stretching your sk/n can help prevent skin

irritation.

□ Make sure the shaving head is always in full

contact with your skin.

B Turn Groomer OFF by pressing the on/off

button (Fig. 8).

Cleaning

I The Groomer should be cleaned after each use. I Always switch Groomer OFF and remove

power cord from charging stand and outlet before cleaning.

I Do not use compressed air. abrasive

cleaning agents, scourers or aggresive liquids such as gasoline, alcohol, benzene bleach or acetone to clean the appliance.

I Never clean, remove or replace shaving head

assembly while motor is on.

I Do not apply pressure to shaving head. Do not

touch foil with hard objects as this may dent or damage foil or cutters. If damage occurs, replace damaged parts.

I Do not use Groomer if foil, cutters, trimmers

or combs are damaged or broken as injury may occur.

I Only use the cleanir^ brush supplied. Any other

brush may cause damage.

Cleaning the shaving unit

Always switch Groomer OFF, remove the power cord from outlet and charging stand before cleaning.

Q Remove any trimming comb from Groomer

(%9).

Q Remove the shaving head by pulling it off

the appliance (Fig. 10).

Hold the shaving head by the plastic housing only.

□ Lift the printed-circuit board out of the inner

body, turn it over and cut the wires that connect the battery to the power unit

Do not attempt to replace batteries. Insulate battery ends by covering with tape and/or place battery in a small plastic bag.

□ Discard Groomer. Do not attempt to plug

electrical cord into the outlet or recharge Groomer after the batteries have been removed.

PHILIPS

^NORELCO

Bodygroom

System

□ Rinse the shaving head under warm running

tap water to rinse away debris (Fig. 11).

Do not use ire cleaning brush to clea- the

shaving head as this mav cause damage to the foil

or cuttcrs>

B Clean the hair chamber with the cleaning

brush. You may also rinse the hair chamber under warm running tap water to remove any residual debris (Fig. 12).

□ Do not use a towel or cloth to dry shaving

foil or cutters as this may cause damage; allow to air dry thoroughly.

Reattach the shaving head by snapping it back

onto the Groomer (Fig. 13).

□ Rinse the Groomer body under njnning warm

tap water. Wipe dry with a soft clean towel or cloth.

Replacing the Shaving Head

I If the shaving foil and cutters are worn or

damaged, do not continue using the Groomer. Replace the shaving foil and cutters immediately.

I It is recommended that you replace your

shaving foil and cutters once a year.

IA worn or damaged shaving foil or cutters

should only be replaced with an original Philips Norelco shaving head, model BG2000. which is available on the Philips Norelco website. www.philips.com/support or call 1^00-243-3050 for assistance.

I The foil is a precision part Handle with care.

Always switch Groomer OFF and remove Groomer from the charging stand before replacing shaving head.

Q Remove the shaving head by pulling it off

the appliance (Fig. 10).

B Place the new shaving head on the Groomer

by snapping it into place (Fig. 13). You will hear a "click”.

After replacing the shaving head, check that the shaving head is firmly attached before using Groomer

This Groomer has no other user-serviceable parts. For assistar>ce call 1 •8Q0-243-3Q5Q.

Storage

i Be sure Groomer is turned off. Remove

power cord from outlet and charging stand before storing in a safe, dry location where it will not be crushed, banged, or subject to damage.

t Do not wrap power cord around Groomer/

charging stand when storing.

t Store cord in a safe location where It will not

be cut or damaged.

t Do not place or store Groomer/charging stand

where it can fall or be pulled into a tub or sink, water or other liquid while plugged in.

Battery Removal

t This Philips Norelco Groomer contains

Nickel Metal Hydride rechargeable batteries which must be disposed of prt^erly (Fig. 14).

i Batteries should only be removed when

Groomer is to be discarded.

I For assistance, call toll free: 1-800-243-3050

or visit our website, www.philips.com/support.

D Conuct your local town or city officials

for battery disposal information or call 1-800-8-BATTERY or

www.rbrc.com for

drop-off locations.

Assistance

For assistance, visit our website; www.philips.com/support or

call 1-800-243-3050 Online information is available 24 hours a day.

7 days a week.

Accessories

I For maximum Groomer performance replace

shaving head once a year.

I Replacement Shaving Head

Model ВС20(Ю-РпШр$ Norelco Rcf^cemcnt Shaving Head

I Replacement Parts may be purchased on

our website

www.philips.com/store

BG2028 Rechargeable Cordless

Always here to help you

www.norelco.com/register

4222 002 82S4 3

PHILIPS

^NORELCO

45-DAY MONEY-

BACK GUARANTEE

If you are not fully sattsfied with your Philips Norelco Groomer send the product back and we’ll refund you the full purchase price. The Groomer must be shipped prepaid by insured mail, insurance prepaid, have the original sales receipt, indicating purchase price and date of purchase, and the money-back guarantee return authorization form enclosed. We cannot be responsible for lost mail. The Groomer must be postmarked no later than 4S days after the date of purchase. Philips Norelco reserves the right to verify the purchase price of the product and limit refunds not to exceed suggested retail price.

To obtain money-back guarantee return authorization form, call 1-800-243-30S0 for assistance.

Delivery of refund check will occur 6-8 weeks AFTER receipt of returned product.

Full Two-Year Warranty

PhAps Eectrono North Amer>u Софогдъоп wurtna Mch new ^>ps Noreico product. Model ЭС2028 (except cutters and cembs) agantt delects n rruterub or vkotimanihap for a penod Ы two years (ran ihe date of purchase.and agrees to repar or reptace any defoewe produn

WlttrOU! -hj’i’-

IMPORTANT: Thu warranty do« not солг damage гечЛг^ from auidentmouse or abuse; lack of геамгиЫес^ Ihe affixrgol any attachment not provided with the product or loss the product to any but the speo<^ voltage.* Use of irtaud<onzcd replicement parts wi vod the warranty.

PHIUPS ELECTRONICS NORTH AMERICA CORPORATION WILL NOT PAY FORWARRANTY SERVICE PERFORMED BY A NON.AUTHORIZED REPAIR SERVICE AND WILL NOT REIMBURSE THE CONSUMER FOR DAMAGE RESULTINC FROM WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED REPAIR SERVICE. NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL. INCIDENTAL OR CONSEQUENTIAL DAMAGES.

In order to oPtan warranty servee. smply go to wwwpiWpscorrV norelco or cal 1-BO(>-243-306Oforasvstance.lt>ssuggeRed that for your protection you return shpanenu of prodjct by rnurod mil nsurance preoaid Damage ocomng dxing sNpment о not covered by thiswarraniy NOTE: No olher warranty written or oraL 5 authonied by №tps EiectroracsNoflh America Corporation T>wswafrarffyg4« you specific legal ngfrts, and you may abo have other nghls which vary from state to state. Some stat« do not allow the еккпюп or Imtation of nodcmal or conscr^ucrmal damages, so the яЬ9Л cxduwn and trrvtations may not ap^ to yoa *Rciad enclosed rsstruclions caiefiAy.

Manu^Ktured fisr:

FT) fips Consumer Uiest^ AOrv«cnof^vaps Qectroncs North America Corporatfon RO BoK 10313. Stamford. CT 06904

Шм Thstjmbolonihrprodjct'srertvptacrnvMntais ШШ htedbyUsdctwrilms'LabonConeblrK.

NcrcfcottaRegiatrfdTradtmirteofPhiptnertrents

North Алегка Софогаьоп

PI« FS n j Rrxntrrrd Iiwlnrwk Ы Konridfr N V

02013 FWpsUectroncsNorPiAmwKaCorporationAIR^tsRomwd

Ы parts or sub|ccung

Be certain Groomer is OFF and removed

from charging stand before dismantling. Allow the Groomer to run until the batteries are completely empty/depleted. Turn Groomer OFF.

B Insert a flathead screwdriver into the slot at

the bottom of the handle and turn it to unlock the rear panel of the housing.

Remove the rear panel of the housing and then remove the side panels.

□ Loosen the screws that connect the Inner

body of the appliance to the front panel of the housing and separate the inner body

from the front panel.

Use a screwdriver to pry open the latches

that lock the inner body. Lift off the cover.