Philips BDP-3406-Mk2 Service Manual

Blu-ray Disc Player

BDP3406

/F7

TABLE OF CONTENTS

Chapter

Technical Specification, PCBs Location………………….. 1 Safety Instruction ……………………………………………… 2 Instruction for Use……………………………………………… 3 Mechanical and Dismantling Instructions…………………. 4 Service Modes, Troubleshooting……………………………. 5 Overall Block Diagram, Wiring Diagram……………………. 6 Electrical Diagram……………………………………………… 7 Exploded View Diagram & Service Part List………………..8 Revision List……………………………………………………. 9

Remark: The Service Manual only for S/N starting from GS1Bxxxxxxxxx. For defective sets with S/N GS1Axxxxxxxxx, please refer to Service Manual with code number 314178536331.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

Published BG LE Printed in The Netherlands Subject to modification

Version 1.1

Version 0.0

314178536661

1-1

1.1 Specifications

Specifications are subject to change without notice

Playable media

- BD-Video

- DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R/-R DL (Dual Layer)

- VCD/SVCD

- Audio CD, CD-R/CD-RW, MP3 media, WMA media, JPEG iles

- DivX (Ultra)/DivX Plus HD media, MKV media

- USB storage device File format

- Video: .avi, .divx, .mp4, .mkv

- Audio: .mp3, .wma, .wav

- Picture: .jpg, .gif, .png Video

- Signal system: PAL / NTSC

- Composite video output: 1 Vp-p (75 ohm)

- HDMI output 480p, 576p, 720p, 1080i, 1080p, 1080p24 Audio

- 2 Channel analog output

- Audio Front L&R : 2 Vrms (> 1 kohm)

- Digital output: 0.5 Vp-p (75 ohm)

- Coaxial

- HDMI output

- Sampling frequency:

- MP3: 32 kHz, 44.1 kHz, 48 kHz

- WMA: 44.1 kHz, 48 kHz

- Constant bit rate:

- MP3: 112 kbps - 320 kpbs

- WMA: 48 kpbs - 192 kpbs USB

- Compatibility: Hi-Speed USB (2.0)

- Class support: USB Mass Storage Class (UMS)

- File system: FAT16, FAT32

- Support HDD (a portable hard drive disc): an external power source may be needed. Main unit

- Power supply rating: AC 110-120V~, 50Hz - 60Hz

- Power consumption: 18 W

- Power consumption in standby mode: < 1 W

- Dimensions (w x h x d): 435 X 41 X 195.5 (mm)

- Net Weight: 1.47 kg Accessories supplied

- Remote control and batteries

- User manual Laser Specification

- Laser Type (Diode): AlGaInN (BD), AlGaInP (DVD/CD)

- Wave length: 405+7nm/-7nm (BD), 655+10nm/-10nm (DVD), 790+10/-20nm (CD)

- Output power: 1mW (BD), 0.26mW (DVD), 0.3mW (CD)

1.1 PCBs Location

1-2

PSU PCBA

MAIN BOARD

VERSION VARIATIONS

pe/Versions:

Service policy

Board in used:

MAIN BOARD

PSU PCBA LED DISPLAY PCBA

*TIPS: C -- Component Lever Repair. M -- Module Lever Repair X -- OCX

LED DISPLAY PCBA

BDP3406

MKII

M M

Software check and upgrade

Preparation to upgrade software

1)Start the CD burning software & create a folder named "UPG_ALL",

2)Then copy the Bin file (BDP3XXXXX-XXX-XXXXXX.bin) into it,

3)Burn the data onto the blank CD.

1-3

B. Read out the software versions to confirm upgrading

4) In homemenu,enter "setup"->"advanced"->"version info", press "OK"

A. Procedure for software upgrade

A) Upgrade software via Disc

1) Power on the set and insert the prepared Upgrade

CDR.

2) The set will starts reading disc & response with the

following display TV screen: Versions

Now searching for upgrade software!

Please wait…!

3) Then screen will display :

software upgrades for this player has been found!Do you want to upgrade?

Model:XXX.XXX

and other information will display on the TV screen as below:

subinfo:xxxx

system SW:xxxx

ethernet MAC:xxxxxxxx

http://www.philips.com/support

Caution: The set must not be power off during

upgrading, otherwise the Main board will be

Cancel Start

4) Press Right cursor button to choose "Start", then press <OK>;

5) The software will updagrde and screen will display as below:

Upgrade is ongoing, Please wait…

Please do not unplug or switch off the device.

6) Restart the set.

B) Update software via USB Flash Drive:

1) Go to www.philips.com/support to check if the latest software

version is available for this player.

2) Download the software onto a USB flash drive's root DIR named "UPG_ALL".

3) Insert the USB flash drive to the USB jack of the rear panel.

4) In the Home menu, select <Setup>-<Advanced>-<Software

update>-<USB>.

5) Then press OK

6) you'll see now searching for new software, please wait.......

7) Waiting, the you'll see "software for this player has been found ......"

8) Then select "Start" and press "OK"

9) then you'll see "upgrade is ongoing ......", wait until it ends.

10) Player will restart automatically or press "Restart now" to restart, after restarting the upgrade ends.

damaged entirely.

2-1

2.0 Safety

1. General

Safety regulations require that during a repair:

. Connect the unit to the mains via an isolation

transformer.

. Replace safety components indicated by the

symbol

Only by components identical to the original ones.

Any

Other component substitution (other than original

type)

May increase risk of fire or electrical shock hazard.

Safety regulations require that after a repair, you

must

Return the unit in its original condition. Pay, in

particular,

Attention to the following points:

. Route the wires/cables correctly, and fix them with

the

mounted cable clamps

. Check the insulation of the mains lead for external

Damage

. Check the electrical DC resistance between the

mains

Plug and the secondary side:

1) Unplug the mains cord, and connect a wire

between

The two pins of the mains plug.

2) Set the mains switch the “on” position (keep

the

Mains cord unplug).

3) Measure the resistance value between the

mains

plug and the front panel, controls, and chassis

bottom.

4) Repair or correct unit when the resistance

measurement is less than 1M Ω

5) Verify this, before you return the unit to the

customer/user (ref. UL-standard no. 1492).

6) Switch the unit “off”, and remove the wire

between

the two pins of the mains plug.

instruction

safety

2. Laser safety

This unit employs a laser. Only qualified service

personnel

May remove the cover, or attempt to service this

device

(due to possible eye injury).

Laser device unit

Type :Semiconductor laser GaAIAs

Wavelength :650nm (DVD)

:780nm (VCD/CD)

Output power :7mW(DVD)

:10mW(DVD/CD)

Beam divergence:60 degree

Note: Use of controls or adjustments or

performance of procedure other than those

specified herein, may result in hazardous

radiation exposure. Avoid direct exposure to

beam.

3-1

3.0 Instruction for Use

You can download this information from the following websites:

http://www.philips.com/support http://www.p4c.philips.com

4-1

4.0 MECHANICAL AND DISMANTLING INSTRUCTIONS

The following guidelines show how to dismantle the player.

Step1: Remove 3 screws a

Step2: Dismantling Front Panel,the CD door should be removed first, then gently pull the Panel out from the set.

use an acuate press the reset hole to release the disc tray; remove the door from the tray; PS: insert reset hole once the disc tray jammed

round the Top Cover, and then remove the Top Cover

Step3: Remove the 9 scre

ws on board to dismantle the DVD BOARD & PSU BOARD & DECK

+ 16 hidden pages