Philips B5/93 Operation Manual

Download

Question?

Contact

Philips

Soundbar speaker

wireless detachable speakers and subwoofer

wireless music streaming with Bluetooth

User manual

Always there to help you

Contents

1 Important 2

Safety 2 Care for your product 3 Care of the environment 3 Help and support 3

2 Your SoundBar 4

Main unit 4 Remote control 4 Wireless portable speakers 5 Wireless subwoofer 6 Connectors 7

3 Connect and set up 7

Charge portable speakers 7 Pair up with subwoofer/speakers 8 Place speakers 8 Connect to TV 9 Connect digital devices through

HDMI 10

Connect audio from TV and

other devices 10

6 Update software 18

Check software version 18 Update software via USB 18

7 Wall mount your SoundBar 19

Wall mount 19

8 Productspecications 20

9 Troubleshooting 21

English

4 Spatial calibration 11

Step 1: calibrate the listening

zone 12

Step 2: calibrate the surround

speaker position 12

5 Use your SoundBar 13

Adjust the volume 13 Choose your sound 13 MP3 player 15 Play music via Bluetooth 15 Connect Bluetooth via NFC 17 Auto standby 17 Set display brightness 17 Apply factory settings 17

1 Important

Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply.

Safety

Riskofelectricshockorre!

• Never expose the product and

accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power outlet immediately. Contact Consumer Care to have the product checked before use.

• Never place the product and

accessories near naked ames or

other heat sources, including direct sunlight.

• Never insert objects into the

ventilation slots or other openings on the product.

• Where the mains plug or an appliance

coupler is used as the disconnect device, the disconnect device shall remain readily operable.

• Disconnect the product from the

power outlet before lightning storms.

• When you disconnect the power cord,

always pull the plug, never the cable.

Riskofshortcircuitorre!

• Before you connect the product to the

power outlet, ensure that the power voltage matches the value printed on the back or bottom of the product. Never connect the product to the power outlet if the voltage is different.

Riskofinjuryordamagetothisproduct!

• For wall-mountable products, use

only the supplied wall mount bracket. Secure the wall mount to a wall that can support the combined weight of the product and the wall mount. WOOX Innovations bears no responsibility for improper wall mounting that results in accident, injury or damage.

• Never place the product or any

objects on power cords or on other electrical equipment.

• If the product is transported in

temperatures below 5°C, unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet.

• Parts of this product can be made of

glass. Handle with care to avoid injury and damage.

Riskofoverheating!

• Never install this product in a conned

space. Always leave a space of at least four inches around the product for ventilation. Ensure curtains or other objects never cover the ventilation slots on the product.

Riskofcontamination!

• Do not mix batteries (old and new or

carbon and alkaine, etc.).

• Danger of explosion if batteries are

incorrectly replaced. Replace only with the same or equivalent type.

• Remove batteries if they are

exhausted or if the remote control is not to be used for a long time.

• Batteries contain chemical substances,

they should be disposed of properly.

Riskofswallowingbatteries!

• The product/remote control may

contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion.

• If you suspect that a battery has been

swallowed or placed inside any part of the body, seek immediate medical attention.

• When you change the batteries, always

keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery.

• If the battery compartment cannot be

completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer.

This is CLASS II apparatus with double insulation, and no protective earth provided.

Care for your product

Use only microber cloth to clean the

product.

Care of the environment

Disposal of your old product

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Do not throw away the product with the normal household waste at the end of its

life, but hand it in at an ofcial collection

point or recycling. By doing this, you help to preserve the environment.

Help and support

For extensive online support, visit www.philips.com/support to:

• download the user manual and the

quick start guide

• watch video tutorials (available only for

selected models)

• nd answers to frequently answered

questions (FAQs)

• email us a question

• chat with our support representative.

Follow the instructions on the website to select your language, and then enter your product model number. Alternatively, you can contact Consumer Care in your country. Before you contact, note down the model number and serial

number of your product. You can nd this

information on the back or bottom of your product.

English

2 Your SoundBar

c d

f g h i j k l

e p

Remote control

Congratulations on your purchase, and

welcome to Philips! To fully benet from

the support that Philips offers, register your SoundBar at www.philips.com/welcome.

Main unit

This section includes an overview of the main unit.

ab c

a Display panel

b (Standby-On/Standby indicator)

When the SoundBar is in standby, the standby indicator turns red.

This section includes an overview of the remote control.

c NFC tag

Tap the NFC-enabled device on the tag for Bluetooth connection.

Switch the SoundBar on or to standby.

b Source buttons

• HDMI ARC: Switch your source to

HDMI ARC connection.

• HDMI 1: Switch your source to the

HDMI IN 1 connection.

• HDMI 2: Switch your source to the

HDMI IN 2 connection.

• COAX: Switch your audio source

to the coaxial connection.

• OPTICAL: Switch your audio

source to the optical connection.

• AUDIO IN: Switch your audio

source to the MP3 connection (3.5mm jack).

• : For Bluetooth on the main unit

only: Switch to Bluetooth mode.

• AUX: Switch your audio source to

the AUX connection.

c /

For Bluetooth on the main unit only: skip to the previous or next track.

For Bluetooth on the main unit only: play, pause or resume.

e BASS +/-

Increase or decrease bass on the main unit.

f Volume control

• +/-: Increase or decrease volume.

• : Mute or restore volume.

g VOICE

• Press to select voice clarity sound

mode.

• Press and hold to toggle on or

off CLOSE TO ME (close to me) sound mode.

l AUTO VOL.

Turn auto volume on or off.

m CALIBRATION

• Press and hold to trigger

calibration for listening zone.

• Press three times to trigger

calibration for the portable left and right speakers position.

n DIM

Set the brightness of SoundBar display panel.

o MOVIE

Select surround sound mode.

p TREBLE +/-

Increase or decrease treble on the main unit.

Wireless portable speakers

The SoundBar comes with two wireless portable speakers (left and right).

b ea dc

English

h MUSIC

Select stereo sound mode.

i REAR VOL.+/-

Press to increase or decrease volume of the portable left and right speakers (only applicable when the portable left and right speakers are wirelessly connected to the main unit (or SURROUND ON DEMAND mode switches on)).

j AUDIO SYNC +/-

Increase or decrease audio delay.

k NIGHT

Turn night mode on or off.

* The illustration above is for overview of

the portable left speaker.

a Reset key

Press with a pin to reset the portable speaker to the default settings.

b ON

• Press to turn on the portable

speaker if it automatically goes to standby.

• Press and hold to switch the

portable speaker to standby.

c Speaker LED

• Blinks in red and orange

alternatively if the portable speaker is not wirelessly connected to the main unit.

• Lights up white when the portable

speaker is wirelessly connected to the main unit, or when the battery capacity is full or more than 30% remaining.

• Lights up red when the battery

capacity is less than 30% remaining .

• Blinks red when the battery

capacity is less than 10% remaining.

• Lights up orange when the

portable speaker is being charged (only for the portable speakers docked into the main unit).

d SURROUND ON DEMAND button/

LED

• Press to switch the portable

speaker to SURROUND ON DEMAND mode.

• The LED lights up white when

the portable speaker is switched to SURROUND ON DEMAND mode.

Note

• If you press the button on the

portable speaker, the portable speaker disconnects the main unit (or SURROUND ON DEMAND mode switches off).

Wireless subwoofer

The SoundBar comes with a wireless subwoofer.

a CONNECT (connect)

Press to to enter the pairing mode for the subwoofer.

e button/LED

• Press to switch the portable

speaker to Bluetooth mode.

• The LED blinks when you switch

the portable speaker to Bluetooth and no Bluetooth devices are connected.

• The LED lights up when you

switch the portable speaker to Bluetooth and Bluetooth devices are connected.

b Subwoofer indicator

• When the power is turned on, the

indicator lights up.

• During wireless pairing between

the subwoofer and the main unit, the indicator blinks white quickly.

• When the pairing succeeds, the

indicator lights up white.

• When the pairing fails, the indicator

blinks white slowly.

c AC MAINS~

Connect to the power supply.

Connectors

3 Connect and set

This section includes an overview of the connectors available on your SoundBar.

a c de g hb f

a AUDIO-IN

Audio input from, for example, an MP3 player (3.5mm jack).

b AUX-AUDIO IN L/R

Connect to an analog audio output on the TV or an analog device.

c DIGITAL IN-COAXIAL

Connect to a coaxial audio output on the TV or a digital device.

d (SERVICE)

Connect a USB ash drive to upgrade

software of this product (not for media play).

e DIGITAL IN-OPTICAL

Connect to an optical audio output on the TV or a digital device.

f HDMI IN1 / HDMI IN2

Connect to the HDMI output on a digital device.

g TO TV-HDMI OUT (ARC)

Connect to the HDMI (ARC) input on the TV.

This section helps you connect your SoundBar to a TV and other devices, and then set it up. For information about the basic connections of your SoundBar and accessories, see the quick start guide.

Note

• For identication and supply ratings,

see the type plate at the back or bottom of the product.

• Before you make or change any

connections, make sure that all devices are disconnected from the power outlet.

Charge portable speakers

If the portable left/right speaker is undocked from the main unit, its battery level is indicated by the LED on the speaker.

• Light up white: full battery or more

than 30% capacity remaining

• Light up red: low battery level, less

than 30% remaining

• Flash red: near empty, less than 10%

remaining

English

h AC MAINS~

Connect to the power supply.

1 Dock your portable speakers into the

main unit to charge.

2 Turn on the main unit.

» During charging, the LED on the

portable speaker lights up orange.

» When fully charged, the LED on

the portable speaker lights up white for 10 seconds.

Note

• It may take around two hours to fully

charge the portable speakers.

• Battery performance varies due to

many factors including volume, sound setting and media played.

2 Press the CONNECT (connect)

button on the subwoofer to enter the pairing mode.

» The indicator on the subwoofer

blinks white quickly.

3 In OPTICAL mode (press OPTICAL)

, within six seconds, on the remote control, press twice then Volume + once, and then hold down BASS +.

» If the pairing succeeds, the

indicator on the subwoofer lights up white.

» If the pairing fails, the indicator on

the subwoofer blinks white slowly.

4 If the pairing fails, repeat the steps

above.

Pair up with the speakers

Pair up with subwoofer/ speakers

The wireless speakers and subwoofer automatically pair up with the SoundBar for wireless connection when you turn on the SoundBar, the portable speakers and the subwoofer. If no audio from the wireless speakers and subwoofer can be heard, manually pair up the portable speakers and the subwoofer.

Pair up with the subwoofer

1 Turn on the SoundBar and the

subwoofer.

» If the connection to the SoundBar

is lost, the indicator on the subwoofer blinks white slowly.

1 Turn on the SoundBar and the

portable speakers.

» If the connection to the SoundBar

is lost, the LED on the portable blinks in red and orange alternatively.

2 Dock the por table left and right

speakers into the main unit to pair up automatically.

3 If the pairing fails, re-dock the portable

speakers into the main unit.

Place speakers

For best sound effect, position all the speakers towards the seating position and place them close to your ear level (seated).

Dock the portable speakers

SUB

WOOFER

REAR L

REAR R

Note

• Surround sound depends on factors

such as room shape and size, type of

wall and ceiling, windows nd reective

surfaces, and speaker acoustics. Experiment with the speaker positions

to nd the optimum setting for you.

Follow these general guidelines for speakers placement.

1 Seating position:

This is the center of your listening area.

2 Place the SoundBar in front of the

seating position.

3 REAR L (rear left) and REAR R (rear

right): Place the portable speakers (surround) to the left and right side of your seating position, either in line with it or slightly behind it.

4 SUBWOOFER (subwoofer):

Place the subwoofer at least one meter to the left or right of the TV. Leave about 10-centimeter clearance from the wall.

You can also dock the portable left and right speakers into the main unit to listen to audio, for example, watching TV shows and news.

English

Connect to TV

Connect your SoundBar to a TV. You can listen to audio from TV programs through your SoundBar. Use the best quality connection available on your SoundBar and TV.

Connect to TV through HDMI (ARC)

Your SoundBar supports HDMI with Audio Return Channel (ARC). If your TV is HDMI ARC compliant, you can hear the TV audio through your SoundBar by using a single HDMI cable.

1 Using a High Speed HDMI cable,

connect the HDMI OUT (ARC) connector on your SoundBar to the

HDMI ARC connector on the TV.

• The HDMI ARC connector on the

TV might be labeled differently. For details, see the TV user manual.

2 On your TV, turn on HDMI-CEC

operations. For details, see the TV user manual.

Note

• If your TV is not HDMI ARC compliant,

connect an audio cable to hear the TV audio through your SoundBar. (see 'Connect audio from TV and other devices' on page 10)

• If your TV has a DVI connector, you

can use an HDMI/DVI adapter to connect to TV. However, some of the features may not be available.

Connect digital devices through HDMI

2 Connect your SoundBar to TV through

HDMI OUT (ARC).

• If the TV is not HDMI CEC

compliant, select the correct video input on your TV.

3 On the connected device, turn on

HDMI-CEC operations. For details, see the user manual of the device.

Connect audio from TV and other devices

Play audio from TV or other devices through your Soundbar speakers. Use the best quality connection available on your TV, Soundbar, and other devices.

Note

• When your Soundbar and TV are

connected through HDMI ARC, an audio connection is not required.

Connect a digital device such as a set-top box, DVD/Blu-ray player, or games console to your SoundBar through a single HDMI connection. When you connect the devices

in this way and play a le or game, the

• video is automatically displayed on

your TV, and

• audio is automatically played on your

SoundBar.

1 Using a High Speed HDMI cable,

connect the HDMI OUT connector on your digital device to the HDMI IN 1/2 on your SoundBar.

Option 1: Connect audio through a digital optical cable

Best quality audio

1 Using an optical cable, connect

the OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the TV or other device.

• The digital optical connector might

be labeled SPDIF or SPDIF OUT.

Option 2: Connect audio through a digital coaxial cable

Best quality audio

1 Using a coaxial cable, connect the

COAXIAL connector on your SoundBar to the COAXIAL/DIGITAL OUT connector on the TV or other

device.

• The digital coaxial connector might

be labeled DIGITAL AUDIO OUT.

Option 3: Connect audio through analog audio cables

Basic quality audio

1 Using an analog cable, connect the

AUX connectors on your SoundBar to

the AUDIO OUT connectors on the TV or other device.

4 Spatial

calibration

Spatial calibration is used to achieve the following convenience, and simultaneously optimizes surround sound experience for it.

• Have freedom to place the portable

left and right speakers (surround) according to your need.

• Automatically balance the portable

speakers (surround) with respect to your seating position.

The spatial calibration involves two steps.

• Step 1: calibrate the listening zone

• Step 2: calibrate the surround speaker

position

When to calibrate

• If you perform spatial calibration for

the rst time, perform Step 1 and Step 2 in sequence.

• If you re-design your seating layout,

perform Step 1 and Step 2 in sequence.

• If you re-locate the portable left and

right speakers (surround), perform Step 2 independently (Step 1 can be skipped).

English

DVD

Before you start

• Make sure that the room is fairly quiet.

• Place the portable left and right

speakers angled towards the main unit.

• Make sure that the main unit, the

portable left and right speakers can fully "see" each other, no obstacle between them blocking such view. Stand the portable speakers upright if needed.

• The minimum distance between the

portable speakers and the main unit is 0.8m (2.6'), the maximum distance 6m (20').

Step 1: calibrate the listening zone

Step 2: calibrate the surround speaker position

1 Place the por table left and right

speakers on two seating positions you prefer most (such as on a sofa).

• Make sure that the portable left

and right speakers are wirelessly connected to the main unit (press SURROUND ON DEMAND on the speaker).

2 Press and hold CALIBRATION on the

remote control for three seconds to trigger calibration.

» ZONE (zone) is displayed on the

display panel.

» You can hear the calibration tones

from the portable speakers.

3 Wait until the calibration tones end.

» ->SPKR (speaker) is displayed on

the display panel.

4 Then perform the following Step

2 (calibrate the surround speaker position) to complete and store the new settings.

1 Place the por table left and right

speakers (surround) on the position you prefer.

• Make sure that the portable left

and right speakers are wirelessly connected to the main unit (press SURROUND ON DEMAND on the speaker).

2 Press CALIBRATION once to trigger

calibration.

• Press CALIBRATIONthree

times to trigger calibration if you re-locate the portable left and right speakers and skip Step 1 (calibrate the listening zone) after you completed a round of spatial calibration previously.

» You can hear the calibration tones

from the portable speakers.

3 Wait until the calibration tones end.

» If the calibration succeeds, DONE

(done) is displayed on the display panel. And the new settings are stored.

Note

• Spatial calibration takes around three

minutes.

• Surround sound improvement is only

noticeable if the portable left and right speakers (surround) were improperly placed, or if there is strong surround effect in the music you play.

• If the portable left and right speakers

are swapped in placement, during calibration L<->R is displayed for few seconds, then the calibration completes.

• During calibration, you may press

CALIBRATION to cancel calibration, and the settings returns to the default.

• If the spatial calibration fails, an error

message is displayed on the display panel, such as FAIL (fail), and the settings returns to the default.

• If the spatial calibration fails, try the

spatial calibration again, and make sure that the calibration points described at the beginning of this chapter are fully met.

5 Use your

SoundBar

This section helps you use the SoundBar to play audio from connected devices.

Before you start

• Make the necessary connections

described in the quick start guide and the user manual.

• Switch the SoundBar to the correct

source for other devices.

Adjust the volume

1 Press +/- (Volume) to increase or

decrease a volume level.

• To mute sound, press .

• To restore the sound, press

again or press +/- (Volume).

For the portable left and right speakers only

1 When the por table left and right

speakers are wirelessly connected to the main unit (in SURROUND

ON DEMAND mode), press REAR VOL.+/- to increase or decrease a

volume level.

English

Choose your sound

This section helps you choose the ideal sound for your video or music.

Surround sound mode

Experience an immersive audio experience with surround sound modes.

• Press MOVIE to create a surround

listening experience. Ideal for watching movie.

• Press MUSIC to create stereo sound. Ideal for listening to music.

Voice clarity

It makes human voice more clear and outstanding for listening.

1 Press VOICE to switch to voice clarity.

» When voice clarity is turned on,

VOICE is displayed.

2 To exit this sound mode, press MOVIE

or MUSIC to select other sound mode.

CLOSE TO ME (close to me)

For ultimate clear sound without disturbing your neighbors, place both the portable left and right speakers close to you, and activate this feature (to mute the main unit).

Note

• It is applicable only when the portable

left and right speakers are wirelessly connected to the main unit (or SURROUND ON DEMAND mode switches on).

• If CLOSE TO ME (close to me) is

turned on, the functions for MOVIE and MUSIC buttons are disabled.

1 Press and hold VOICE for three

seconds to activate the feature.

» CLOSE TO ME (close to me)

scrolls once on the display panel.

» The main unit is muted.

2 To exit this sound mode, press and

hold VOICE again for three seconds.

» The previous sound mode

switches in.

Equalizer

Change the high frequency (treble) and low frequency (bass) settings of the SoundBar.

1 Press TREBLE +/- or BASS +/- to

change the frequency.

Auto volume

Turn the auto volume on to keep the volume constant when you switch to a different source. It also compresses the sound dynamics, increasing the volume for quiet scenes and decreasing the volume for loud scenes.

1 Press AUTO VOL. to turn auto

volume on or off.

» When auto volume is turned on,

ON AUTO scrolls once on the display panel.

» When auto volume is turned off,

OFF AUTO scrolls once on the display panel.

Synchronize video and sound

If the audio and video are not synchronized, delay the audio to match the video.

1 Press AUDIO SYNC +/- to

synchronize the audio with the video.

• AUDIO SYNC + increases the

sound delay, and AUDIO SYNC - decreases the sound delay.

Night mode

3 Press the buttons on the MP3 player

to select and play audio les or music.

• On the MP3 player, it is

recommended to set the volume in the range of 80% maximum volume.

For quiet listening, night mode decreases the volume of loud sounds when audio is played. Night mode is only available for Dolby Digital soundtracks.

1 Press NIGHT to turn night mode on

or off.

» When night mode is turned on,

ON NIGHT scrolls once on the display panel.

» When night mode is turned off,

OFF NIGHT scrolls once on the display panel.

Note

• If auto volume is set to turned on, you

cannot enable the night mode.

MP3 player

Connect your MP3 player to play your

audio les or music.

What you need

• An MP3 player.

• A 3.5mm stereo audio cable.

1 Using the 3.5mm stereo audio

cable, connect the MP3 player to the AUDIO IN connector on your SoundBar.

2 Press AUDIO IN.

Play music via Bluetooth

Through Bluetooth, connect the SoundBar with your Bluetooth device (such as an iPad, iPhone, iPod touch, Android phone, or laptop), and then you can listen to the

audio les stored on the device through

your SoundBar speakers.

What you need

• A Bluetooth device which supports

Bluetooth prole A2DP, and with

Bluetooth version as 2.1 + EDR.

• The maximum operational range

between the SoundBar and a Bluetooth device is approximately 10 meters (30 feet).

Note

• The music streaming may be

interrupted by obstacles between the device and this product, such as wall, metallic casing that covers the device, or other devices nearby that operate in the same frequency.

• If you want to connect this product

with another Bluetooth device, break the current Bluetooth connection.

English

Bluetooth on the main unit

1 Press on the remote control to

switch the main unit to Bluetooth mode.

» BT on the display blinks.

2 On the Bluetooth device, switch on

Bluetooth, search for and select Fidelio B5 to start connection (see the user

manual of the Bluetooth device on how to enable Bluetooth).

» During connection, BT on the

display blinks.

3 Wait until BT on the display lights up.

» If the connection succeeds, BT on

the display lights up.

» If the connection fails, BT on the

display blinks.

4 Select and play audio les or music on

your Bluetooth device.

• During play, if a call is coming,

music play is paused.

• If music streaming is interrupted,

place the Bluetooth device closer to the main unit.

5 To exit Bluetooth, select other source.

» When you switch back to

Bluetooth mode, Bluetooth connection resumes.

• To break the current Bluetooth

connection, press and hold on the remote control.

Bluetooth on a single speaker

You can use the portable left or the portable right speaker as a standalone Bluetooth speaker, independently from the main unit.

1 Press the button on the left or right

speaker to switch to Bluetooth mode.

» The LED on the left or right

speaker blinks.

2 On the Bluetooth device, switch on

Bluetooth, search for and select the name of the left or right speaker to start connection (see the user manual of the Bluetooth device on how to enable Bluetooth).

• B5 -L portable stands for the

portable left speaker, B5 -R portable for the portable right speaker.

» During connection, the LED on

the left or right speaker blinks.

3 Wait until the LED on the portable

speaker lights up.

» If the connection succeeds,

connection tone is heard, and the

LED on the portable speaker

lights up.

» If the connection fails, the LED

on the portable speaker blinks.

4 Select and play audio les or music on

your Bluetooth device.

• During play, if a call is coming,

music play is paused.

• If music streaming is interrupted,

place the Bluetooth device closer to the main unit.

5 To exit Bluetooth, press the

SURROUND ON DEMAND button

on the speaker.

» When you switch back to

Bluetooth mode, Bluetooth connection resumes.

• To break the current Bluetooth

connection, press and hold the button on the speaker.

Note

• The function of the remote control is

not available to a standalone Bluetooth speaker (the portable left or right speaker).

3 Select and play audio les or music on

your NFC device.

• To break the connection, tap again

the NFC device onto the NFC tag on the main unit.

Auto standby

Connect Bluetooth via NFC

NFC (Near Field Communication) is a technology that enables short-range wireless communication between NFCenabled devices, such as mobile phones.

What you need

• A Bluetooth device with NFC function.

• For pairing, tap the NFC device on the

NFC tag of the main unit.

Note

• NFC feature is only available to the

main unit, not available to the portable left and right speakers.

1 Enable NFC on the Bluetooth device

(see the device' s user manual for details).

2 Tap the NFC device onto the NFC

tag of the main unit until the SoundBar beeps.

• For rst time connection, on

some mobile devices prompt for pair-up appears, select "YES" for connection.

» When the Bluetooth connection

succeeds, BT is displayed on the display panel.

» If the connection fails, BT on the

display panel blinks continuously.

When playing media from a connected device, the SoundBar automatically switches to standby if:

• no source button is pressed for

15 minutes, and

• no audio/video playback is detected

from a connected device.

Set display brightness

You can press DIM repeatedly to select a different brightness level of the display panel on this product.

• If you select DIM O (dim) on the

display, the display turns off after 10 seconds each time you press a button on the remote control.

Apply factory settings

You can reset this product to the default settings programmed at the factory.

1 In AUX mode, on the remote control

press Volume-, BASS -, and TREBLE - in sequence within three seconds.

» When the factory settings

restore is complete, the product automatically switches off and restarts.

English

6 Update software

To get the best features and support, update your product with the latest software.

What you need

• A USB ash drive that is FAT-

formatted. Do not use a USB hard drive.

• A computer with Internet access.

• An archive utility that supports the ZIP

le format.

Check software version

In HDMI ARC source, on the remote control press TREBLE -, BASS -, and Volume- in sequence within three seconds.

» The software version number is

displayed on the display panel.

3 Connect the USB ash drive to the

(SERVICE) connector on this

product.

4 Switch this product to HDMI ARC

source (press HDMI ARC).

5 On the remote control, within

6 seconds press twice then

Volume + once, and then hold down MOVIE.

» Then "UPG" (upgrade) is displayed

on the display panel.

6 Wait until the upgrade is completed.

» If the upgrade is complete, this

product automatically turns off and on again.

Caution

• Do not turn off the power or remove

the USB ash drive when the software

update is in progress because you might damage this product.

• The upgrade time may take around

eight minutes.

Update software via USB

1 Check the latest software version on

www.philips.com/support.

• Search for your model and click on

"Software and drivers".

2 Download the software into a USB

ash drive.

a Unzip the download if zipped,

and make sure that the unzipped folder is named "UPG".

b Put the "UPG" folder in the root

directory.

7 Wall mount

your SoundBar

Before you mount your SoundBar on the wall, read all safety precautions. (see 'Safety' on page 2)

Wall mount

Note

• You must detach the portable

speakers from the main unit before wall mounting or un-mounting.

• Improper wall mounting may result in

accident, injury or damage. If you have any query, contact Consumer Care in your country.

• Secure the wall mount to a wall that

can support the combined weight of the product and the wall mount.

• Before wall mount, you need not

remove the four rubber feet at the bottom of the soundbar, otherwise the

rubber feet cannot be xed back.

3 - 3.5mm

See the illustration on the separate wall mount sheet on how to wall mount the SoundBar.

1) Drill holes on the wall.

2) Secure the wall bracket on the wall with

3) Hang the SoundBar on the wall bracket.

> 25mm

the dowels and screws.

English

Screw length/diameter

Depend on the type of wall mounting this wall mount bracket, make sure that you use screws of a suitable length and diameter.

8 Product

specifications

Note

• Specications and design are subject to

change without notice.

Amplier

• Built-in speakers

• 2 x woofer (76 mm/3”, 8 ohm)

• 2 x tweeter (25.4 mm/1”, 8 ohm)

Portable speakers

• Speaker impedance: 8 ohm

• Speaker drivers: 2 x 76 mm (3") full

range

• Dimensions (W x H x D):

191 x 73 x 156 mm

• Weight: 0.86 kg/each

• Total output power:

210W RMS (+/- 0.5 dB, 30% THD) / 168W RMS (+/- 0.5 dB, 10% THD)

• Frequency response:

20 Hz-20 kHz / ±3 dB

• Signal-to-noise ratio:

> 65 dB (CCIR) / (A-weighted)

• Input sensitivity:

• AUX: 750 mV

• AUDIO IN: 400 mV

Audio

• S/PDIF Digital audio input:

• Coaxial: IEC 60958-3

• Optical: TOSLINK

Bluetooth

• Bluetooth proles: A2DP

• Bluetooth version: 2.1 + EDR

Main unit

• Power supply: 110-240 V~, 50-60 Hz

• Power consumption: 50 W

• Standby power consumption: ≤ 0.5 W

• Dimensions (W x H x D): 1035 x 73 x 156 mm (with portable left and right speakers attached)

• Weight: 4.4 kg

Subwoofer

• Power supply: 110-240 V~, 50-60 Hz

• Power consumption: 30 W

• Standby power consumption: ≤ 0.5 W

• Impedance: 4 ohm

• Speaker drivers: 1 x 165 mm (6.5")

woofer

• Dimensions (W x H x D):

200 x 510 x 201 mm

• Weight: 4.9 kg

Wall mount

• Dimensions (W x H x D): 40 x 100 x 26.5 mm

• Weight: 0.1 kg/each

Remote control batteries

• 2 x AAA-R03-1.5 V

Standby information

• When the product remains inactive for

15 minutes, it automatically switches to standby or networked standby.

• The power consumption in standby or

networked standby is less than 0.5W.

• To deactivate Bluetooth connection,

press and hold the Bluetooth button on the remote control.

• To activate Bluetooth connection,

enable Bluetooth connection on your Bluetooth device, or enable Bluetooth connection via the NFC tag (if available).

9 Troubleshooting

Warning

• Risk of electric shock. Never remove

the casing of the product.

To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following points before you request service. If you still have a problem, get support at www.philips.com/support.

Sound

No sound from SoundBar speakers.

• Connect the audio cable from your

SoundBar to your TV or other devices. However, you do not need a separate audio connection when:

• the SoundBar and TV are

connected through HDMI ARC connection, or

• a device is connected to the HDMI

IN connector on your SoundBar.

• On the remote control, select the

correct audio input.

• Make sure that the SoundBar is not

muted.

• Reset your SoundBar to its factory

settings (see 'Apply factory settings' on page 17).

English

No sound from the wireless portable speakers.

• Make sure that the wireless portable

speaker is turned on. Press ON on the bottom of the wireless portable speaker.

• Dock the wireless portable speakers

into the main unit to charge the battery.

• If you intend the wireless portable

speaker to wirelessly connect to the main unit, make sure that you press the SURROUND ON DEMAND button on the wireless portable speaker.

• If you intend the wireless portable

speaker to be a standalone Bluetooth speaker, make sure that you connect the portable left or right speaker to a Bluetooth device (see 'Bluetooth on a single speaker' on page 16).

No sound from the wireless subwoofer.

• Wirelessly connect the subwoofer to

the main unit.

Distorted sound or echo.

• If you play audio from the TV through

the SoundBar, make sure that the TV is muted.

Quality of audio play from a connected Bluetooth device is poor.

• The Bluetooth reception is poor. Move

the device closer to the SoundBar, or remove any obstacle between the device and the SoundBar.

The connected Bluetooth device connects and disconnects constantly.

• The Bluetooth reception is poor. Move

the device closer to the SoundBar, or remove any obstacle between the device and the SoundBar.

• Turn off Wi-Fi function on the

Bluetooth device to avoid interference.

• For some Bluetooth, the Bluetooth

connection can be deactivated automatically to save power. This does not indicate any malfunction of the SoundBar.

Audio and video are not synchronized.

• Press AUDIO SYNC +/- to

synchronize the audio with the video.

Bluetooth

A device cannot connect with the SoundBar.

• The device does not support the

compatible proles required for the

SoundBar.

• You have not enabled the Bluetooth

function of the device. See the user manual of the device on how to enable the function.

• The device is not correctly connected.

Connect the device correctly.

• The SoundBar is already connected

with another Bluetooth device. Disconnect the connected device, then try again.

Spatial calibration

Why spatial calibration is needed?

• Spatial calibration optimizes surround

sound experience if your portable left and right speakers (surround) are not properly placed.

Improvement in surround sound is not noticeable after successful spatial calibration.

• Surround sound improvement is only

noticeable if the portable left and right speakers (surround) were improperly placed, or if there is strong surround effect in the music you play.

Error message is displayed on the display panel.

• If spatial calibration fails, one of the

following error message is displayed. Refer to the fourth chapter (Spatial calibration) for details to re-calibrate.

• FAIL (fail): indicates that the

portable left/right speaker is not in SURROUND ON DEMAND mode or out of calibration range, or there is some obstacle by which the main unit, the portable left and right speakers cannot completely "see" each other.

• BATT LOW (battery low):

indicates that the portable left/right speaker has low battery.

• ERR1 (error): indicates that the

portable left and right speakers are not detached from the main unit.

English

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS Digital Surround is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

The terms HDMI and HDMI High-

Denition Multimedia Interface, and the

HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by WOOX Innovations is under license. Other trademarks and trade names are those of their respective owners.

The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries.

部件名称

Name of the parts

Housing

外壳

Subwoofer

超重低音箱

Loudspeakers

喇叭单元

PWBs

电路板组件

Accessories (Remote control & cables)

附件（遥控器，电源线，连接线）

Batteries in Remote Control (ZnC)

遥控器电池

产品中有害物质的名称及含量

Names and Contents of Hazardous Substances

有害物质

Hazardous Substance

铅

(Pb)

O O O O O O

X O O O O O

O O O O O O

X O O O O O

汞

(Hg)

镉

(Cd)

六价铬

(Cr (VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

本表格依据

SJ/T 11364

的规定编制。

The table is formulated according to SJ/T 11364.

：表示该有害物质在该部件所有均质材料中的含量均在

GB/T 26572

规定的限量要求以下。

O： Indicates that this hazardous substance contained in all of the homogeneous materials

for this part is below the limit requirement in GB/T 26572.

×：表示该有害物质至少在该部件的某一均质材料中的含量超出 ×：

Indicates that this hazardous substance contained in at least one of the homogeneous

GB/T 26572

规定的限量要求。

materials used for this part is above the limit requirement in GB/T 26572.

环保使用期限

此标识指期限（十年），电子电气产品中的有害物质在正常使用的条件下不会发生外泄或突变，用户使用该电子电气产品不会对环境造成严重污染或对其人身、财产造成严重损害的期限。

This logo refers to the period (10 years) during which the hazardous substances in electronic and electrical products will not leak or mutate so that the use of these [substances] will not result in any severe environmental pollution, any bodily injury or damage to any asset

Environmental Protection Use Period

Specifications are subject to change without notice 2015 © WOOX Innovations Limited. All rights reserved. Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited under license from Koninklijke Philips N.V.

B5_93_UM_V2.0

Philips B5/93 Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Important

Safety

Care for your product

Care of the environment

Help and support

2 Your SoundBar

Remote control

Main unit

Wireless portable speakers

Wireless subwoofer

Connectors

Charge portable speakers

Pair up with subwoofer/ speakers

Place speakers

Connect to TV

Connect digital devices through HDMI

Connect audio from TV and other devices

Step 1: calibrate the listening zone

Step 2: calibrate the surround speaker position

Adjust the volume

Choose your sound

MP3 player

Play music via Bluetooth

Auto standby

Connect Bluetooth via NFC

Set display brightness

Apply factory settings

6 Update software

Check software version

Update software via USB

Wall mount

9 Troubleshooting