Philips AZ-5130 Service manual

Handling Chip Components and Safety ..........................1 - 1

Technical Specification & Service tools...........................2 - 1

Service Measurement......................................................2 - 2

Connections and controls.....................................3 - 1 to 3- 2

Instructions for Use .............................................3 - 3 to 3 - 8

Disassembly Diagram......................................................4 - 1

Pin-description of ICs..........................................4 - 2 to 4 - 5

Block Diagram .................................................................5 - 1

Wiring Diagram................................................................6 - 1

Tuner And Power Amplifier Board

Circuit Diagram........................................................7 - 1

Layout Diagram.......................................................7 - 2

Radio Alignment......................................................7 - 2

VCD Board And LCD Board

Circuit Diagram .......................................................8 - 1

Layout Diagram(LCD Board) ..................................8 - 2

Layout Diagram(VCD Board) .......................8 - 3 to 8-4

Tape Board

Circuit Diagram........................................................9 - 1

Layout Diagram.......................................................9 - 2

Exploded Views Diagram

Cabinet ..............................................................10 - 1

Tape Deck .........................................................10 - 2

Mechanical Partslist.......................................................10 - 2

Electrical Partslist............................................11 - 1 to 11 - 2

Published by LX 0333Service Audio Printed in The Netherlands Subject to modification



VCD MP3 CD Soundmachine

CLASS 1

LASER PRODUCT

AZ 5130

all versions

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.

VIDEO CD

HANDLING CHIP COMPONENTS

All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set via a wristband with resistance. Keep components and tools at this potential.

f ATTENTION

Tous les IC et beaucoup d´autres semi-conducteurs sont sensibles aux décharges statiques (ESD). Leur longévite pourrait être considérablement écourtée par le fait qu´aucune précaution nést prise à leur manipulation. Lors de réparations, s´assurer de bien être relié au même potentiel que la masse de l´appareil et enfileer le bracelet serti d´une résistance de sécurité. Veiller à ce que les composants ainsi que les outils que l´on utilise soient également à ce potentiel.

d WARNUNG

Alle ICs und viele andere Halbleiter sind empfindlich gegenüber elektrostatischen Entladungen (ESD). Unsorgfältige Behandlung im Reparaturfall kann die Lebensdauer drastisch reduzieren. Sorgen Sie dafür, daß Sie im Reparaturfall über ein Puls- armband mit Widerstand mit dem Massepotential des Gerätes verbunden sind. Halten Sie Bauteile und Hilfsmittel ebenfalls auf diesem Potential.

ñ WAARSCHUWING

Alle IC´s en vele andere halfgeleiders zijn gevoelig voor electrostatische ontladingen (ESD). Onzorgvuldig behandelen tijdens reparatie kan de levensduur drastisch doen vermindern. Zorg ervoor dat u tijdens reparatie via een polsband met weerstand verbonden bent met hetzelfde potentiaal als de massa van het apparaat. Houd componenten en hulpmiddelen ook op ditzelfde potentiaal.

i AVVERTIMENTO

Tutti IC e parecchi semi-conduttori sono sensibili alle scariche statiche (ESD). La loro longevità potrebbe essere fortemente ridatta in caso di non osservazione della più grande cauzione alla loro manipolazione. Durante le riparationi occorre quindi essere collegato allo stesso potenziale che quello della massa delápparecchio tramite un braccialetto a resistenza. Assicurarsi che i componenti e anche gli utensili con quali si lavora siano anche a questo potenziale.

Safety regulations require that the set be restored to its original condition and that parts which are identical with those specified be used. Safety components are marked by the symbol

Le norme di sicurezza estigono che l´apparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambiago identici a quelli specificati. Componenty di sicurezza sono marcati con

Veiligheidsbepalingen vereisen, dat het apparaat in zijn oorspronkeliijke toestand wordt teruggebracht en dat onderdelen, identiek aan de gespecificeerde, worden toegepast. De Veiligheidsonderdelen zijn aangeduid met het symbool

s Varning !

Osynlig laserstrålning när apparaten är öppnad och spärren är urkopplad. Betrakta ej strålen.

∂ Advarsel !

Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå udsaettelse for stråling.

ß Varoitus !

Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina näkymättömälle laserisäteilylle. Älä katso säteeseen !

"Pour votre sécurite, ces documents doivent être utilisés par des spécialistes agréés, seuls habilités à réparer votre appareil en panne".

ESD

SAFETY

Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten. Der Originalzustand des Gerätes darf nicht verändert werden. Für Reparaturen sind Original- ersatzteile zu verwenden. Sicherheitsbauteile sind durch das Symbol markiert.

Les normes de sécurité exigent que l`appareil soit remis à l`état d`origine et que soient utilisées les pièces de rechange identiques à celles spécifiées. Les composants de sécurité sont marqués

CLASS 1

LASER PRODUCT

DANGER: Invisible laser radiation when open.

After servicing and before returning the set to customer perform a leakage current measurement test from all  exposed metal parts to earth ground, to assure no shock hazard exists. The leakage current must not exceed 0.5mA.

AVOID DIRECT EXPOSURE TO BEAM.

1 - 1

GENERAL

Mains voltage

-/10

-/01 120/230 V :

-/10 240 V :

-/01 : 60 / 50 Hz

Mains frequency

: 50 Hz

Battery mains : 9 V (R14 x 6) Power consumption : 15W

AMPLIFIER

Output power mains : 2 x 1.5 W

battery : 2 x 1.5 W

Speaker impedance : 2 x 6 ohm

TUNER - FM SECTION

Tuning range : 87.5 - 108 MHz IF frequency : 10.7 MHz Sensitivity : < 14 dBµV at 26dB S/N Selectivity S9/300kHz : > 20 dB

±0.3MHz

IF rejection : > 50 dB Image rejection : > 20 dB

-3dB limiting point : 18dBµV Distortion : 5%

TUNER - MW SECTION

Tuning range : 526.5 - 1606.5 kHz IF frequency : 456 kHz ± 3 kHz Sensitivity : < 72 dBµV/m at 26dB S/N Selectivity : 16 dB

Channel difference dB

Overall frequency responce

AUDIO CASSETTE RECORDER

Number of tracks : 1 stereo Tape speed : 4.76 cm/sec + 3/-2% Wow & flutter : < 0.35 % JIS Unwtd. Fast wind/rewind C60 : < 130 sec. Frequency response P/B : 125 - 8000 Hz S/N ratio : > 36 dB

120Hz

IF rejection 24 dB

Image rejection ratio 28 dB

COMPACT DISC

S/N ratio unwtd. > 50 dB Channel difference 1 kHz : < 2 dB Crosstalk 1 kHz : > 30 dB Frequency response : ± 2dB at 100Hz THD(1kHz,0dB) : 1.5%

2 - 1

SERVICE TOOLS

Audio signal disc SBC 429.......................................................................4822 397 30184

Playability test disc SBC 444

...................................................................4822 397 30245

Test disc 5 (disc without errors ) + Test disc 5A (disc with dropout errors, black spots and fingerprints)

SBC 426/426A.....................................................................4822 397 30096

Burn in test disc (65 min. 1kHz signal at -30 dB level without “pause”)

.....4822 397 30155

anti-static table mat

large 1200x650x1.25mm  4822 466 10953

small 600x650x1.25m 4822 466 10958

anti-static wristband

4822 395 10223

connection box (3 press stud connections, 1MΩ) 4822 320 11307 extendible cable (2m, 2MΩ, to connect wristband to connection box) 4822 320 11305 connecting cable (3m, 2MΩ, to connect table mat to connection box) 4822 320 11306 earth cable (1MΩ, to connect any product to mat or to connection box) 4822 320 11308 KIT ESD3 (combining all 6 prior products - small table mat) 4822 310 10671 wristband tester 4822 344 13999

AVAILABLE ESD PROTECTION EQUIPMENT

TECHNICAL SPECIFICATIONS

2 - 2

SERVICE MEASUREMENT

Bandpass

250Hz-15kHz

e.g. 7122 707 48001

LF Voltmeter

e.g. PM2534

DUT

RF Generator

e.g. PM5326

S/N and distortion meter

e.g. Sound Technology ST1700B

Tuner SW

To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday«s cage. Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).

Ri=50Ω

Aerial replacement

Capacitor

R=50Ω

Bandpass

250Hz-15kHz

e.g. 7122 707 48001

LF Voltmeter

e.g. PM2534

DUT

S/N and distortion meter

e.g. Sound Technology ST1700B

Frame aerial

e.g. 7122 707 89001

Tuner AM (MW,LW)

To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday«s cage.

RF Generator

e.g. PM5326

Ri=50Ω

Low pass filter 22kHz

LEVEL METER

e.g. Sennheiser UPM550

with FF-filter

S/N and distortion meter

e.g. Sound Technology ST1700B

DUT

Use Audio Signal Disc SBC429 4822 397 30184 (replaces test disc 3) L.P.F. = 13

order filter 4822 395 30204

3 - 1

CONTROLS

English

1 LIFT TO OPEN - to open the CD door.

2 Source selector - POWER ON/OFF switch and

to select source of sound source:

CD•VCD/MW/FM/TAPE.

3 Cassette keys:

PAUSE ; - to interrupt recording or playback.

STOP•OPEN 9/- To stop the tape and to

open the cassette holder.

SEARCH 5 or 6 - to fast wind/rewind the

tape.

PLAY 1 - to start playback.

RECORD 0 - to start recording.

4 REMOTE SENSOR - infrared sensor for

remote control

5 LCD Display - to show the VCD, MP3 functions

and disc status.

6 TUNING - to tune to radio stations

7 PLAY•PAUSE 2; - To start or interrupt

CD playback.

8 STOP 9 - to stop playback

9 SEARCH or §

- to skip or search a passage

or a track

0 DBB (Dynamic Bass Boost) - for a more

vivid bass response.

! REPEAT - to repeat a track/programme/entire

CD playback

@ SHUFFLE - to play all tracks in random order

# VOLUME - to adjust volume level.

$ Telescopic aerial - to improve FM radio

reception

% VIDEO/AUDIO OUT - connect to the TV or

VCR VIDEO/AUDIO IN

^ Battery door - to open the battery

compartment

& AC MAINS

~ - socket for mains lead

Remote Control

. . . . . . . . . . . . . . . . . . . .1 pc

Mains Cord

. . . . . . . . . . . . . . . . . . . . . . .1 pc

Audio / Video Cable

. . . . . . . . . . . . . . . .1 pc

1 PBC (PLAYBACK CONTROL) - to switch on or

off PBC mode (for VCD version 2.0 only).

2 RETURN - to return to the previous MENU level

during playback (for VCD with PBC on).

3 VIEW - to scan through a VCD with 9 pictures

display on TV screen. Only when PBC mode is

switched off (for VCD operation only).

4 OSD - to switch on/off the on screen display on

the TV screen.

5 SLOW - to watch a VCD at a slower speed (for

VCD operation only).

6 RESUME -.to resume playback in stop mode.

7 GOTO - to start playback at any chosen time on

the disc (for CD/VCD operation only and PBC

mode is off).

8 PROG

for CD/VCD/MP3-CD . . . to programme disc

tracks.

REMOTE CONTROL

SUPPLIED ACCESSORIES

BACK PANEL

TOP AND FRONT PANEL

CONNECTIONS AND CONTROLS

12 3 51 6

NIN

U T

REPEAT

•

D-

A R

ASS

L AL

DBB

shuffle

prog

78 9 0!@ #

^%&

VIDEO OUT AUDIO OUT

3 - 2

POWER SUPPLY

English

IMPORTANT!

For best CD/MP3-CD/VCD playback, please plug in your set to an AC power supply where

convenient.

If operated in DC mode, see below approximate playtime. (Playtime is also varied from

different brand batteries) :

The CD part of this system also serves as a Video CD player if you connect it to your TV

set.

Before viewing the Video CD, ensure that the set is switched to corresponding PAL or

NTSC system of your TV set (exception Multi-system TV).

Whenever convenient, use the mains supply if you want to conserve battery life. The battery supply

will be switched off when the set is connected to the mains.

Make sure you remove the plug from the

set and wall outlet before inserting batteries.

Batteries

1. Open the battery compartment and insert six batteries, type

R14, UM2 or C-cells, (preferably

alkaline

) with

the correct

polarity as indicated by the "

+" and "-" symbols inside the

compartment.

Remote control

Open the battery compartment and insert two batteries,

type AAA, R03 or UM4 (preferably alkaline).

2. Replace the compartment door, making sure the batteries are

firmly and correctly in place.

3. Remove the batteries if they are exhausted or if they will not be

used for a long period.

– The incorrect use of batteries can cause electrolyte leakage and

will corrode the compartment or cause the batteries to burst. Therefore:

– Do not mix battery types, e.g. alkaline with zinc carbonate.

– When inserting new batteries, replace all at the same time.

– Remove the batteries if the set is not to be used for a long time.

Notes :

–The battery supply is switched off when the set is connected to the mains.

TV screen is disabled during CD / MP3-CD playing if your AZ5130 is battery

powered.

Batteries contain chemical substances, so they should be disposed of properly

6 x 1.5V R14/ UM2/ C CELL

BATTERIES (NOT SUPPLIED)

Battery type Playtime

Alkaline approximate 9 hrs

Zinc Cartonate approximate 45 minutes

CONNECTIONS AND CONTROLS

REMOTE CONTROL

English

9 REPEAT

for MP3-CD . . . . . . . . to repeat a track, or

whole disc.

for CD/VCD . . . . . . . . to repeat a disc track or

the whole disc.

0 A - B - to playback a certain scene or passage

repeatedly (for CD/VCD operation only).

! ZOOM

for VCD only . . . . . . . to zoom in or zoom out

picture.

@ SHUFFLE - When in CD/VCD mode, press to

start or stop shuffle play mode.

# MIX/SEL - to select disc format (CD / MP3-CD)

in a mixed mode disc.

$ NTSC/PAL - to select the video output for

NTSC or PAL system.

% R/L/ST - to select channel left / channel right /

stereo sound, or to select a language in a

bilingual VCD.

^ DIGITS 0 - 9

for CD/VCD/MP3-CD - to select a

track number.

(numbers consisting more than 2 figures must

be keyed in within 2 seconds)

& PLAY/PAUSE 2;

- to start or interrupt playback.

* SEARCH 5 or 6 (for CD/VCD/MP3-CD)

- to search back or forward.

( ALBUM ¡ ™

for MP3-CD only . . . . to select previous / next

album

) TRACK §

for MP3-CD only . . . . to select previous/next

title.

for CD/VCD . . . . . . . . to search backward/

forward track.

¡ STOP 9

- to stop playback or to clear a programme.

3 - 3

CD/VCD/MP3-CD

English

This set can play all digital audio CD, video CD, finalised digital audio CD-Recordable (CDR) discs

and finalised digital audio CD-Rewritable (CDRW) discs.

Support following MP3-CD formats:

•

ISO 9660 or ISO 9660 + Joliet format - Max. 30 characters

•

Max. Track number is 400

•

Max. nested directory is 8 levels

•

The max. album number is 99

•

The max. MP3 programme track number is 20

•

The max. length of each track is 99 minutes 59 seconds

•

The player can play mixed mode disc of CD / MP3-CD

•

Supported VBR bit-rate

•

Supported sampling frequencies for MP3 disc : 8 kHz to 48 kHz (44.1kHz preferably)

•

Supported bit-rates of MP3 disc are: 32 - 320 kbps (128 kbps preferably)

Following formats are not supported

•

The files like *.WMA, *AAC, *.DLF, *.M3U, *.PLS, MP3 PRO

The non-session closed discs

1. Set the source selector to CD/VCD.

2. Lift to open the CD door.

™"OP" will be displayed

3. Insert a disc with the label side facing up.

4. Close the CD door.

™ The total number of tracks of the disc appear on the display.

™ "no" will be displayed if no disc is inserted or error in CD

operation

For MP3-CD only

™The total track number "XXX" and album number “AXX" will

be displayed interchangeably.

MP3

LOADING A DISC

DISCS FOR PLAYBACK

VCD

MP3

CAUTION

Use of controls or adjustments or performance of procedures other than herein

may result in hazardous radiation exposure or other unsafe operation.

Environmental information

All unnecessary packaging material has been omitted. We have done our utmost to make the

packaging easily separable into three mono materials: cardboard, polystyrene and plastic.

Your set consists of materials which can be recycled if disassembled by a specialized

company. Please observe the local regulations regarding the disposal of packaging

materials, exhausted batteries and old equipment.

INSTRUCTIONS FOR USE

GENERAL OPERATION

English

1. Check if the mains voltage as shown on the type plate (on the

bottom of the set) corresponds to your local mains voltage. If it

does not consult your dealer or service organization.

2. Connect the mains lead to the AC MAINS

~ socket and the

wall socket.

™ The set is now ready for use.

3. To switch off the mains supply completely, pull the mains plug

out of the wall socket.

™ Disconnect the mains lead when you change over to battery supply, or to protect the set

during heavy thunderstorms.

The type plate is located on the bottom of the set.

1. To switch on the set, adjust the source selector.

2. Adjust the sound using the VOLUME and DBB controls.

3 To switch off the set, adjust the source selector to the

TAPE/OFF position, with the cassette keys released.

1 Set the source selector to FM or MW.

2. Adjust the sound using the VOLUME controls and the DBB

switch.

3. Tune to a radio station using the TUNING knob.

– For FM, pull out the telescopic aerial. To improve FM-reception,

incline and turn the aerial. Reduce its length if the FM-signal is

too strong (very close to a transmitter).

– For MW, the set is provided with a built-in aerial, so the

telescopic aerial is not needed. Direct the aerial by turning

the whole set.

4. To switch off, set the source selector to the TAPE/OFF

position (with the cassette keys released).

RADIO RECEPTION

•

ICBASS

DBB

REPE

ALL

all

ffle

MP3

GENERAL OPERATION

MAINS

•

M T

•

3 - 4

CD/VCD/MP3-CD

English

Programming tracks of disc is possible when playback is stopped. Up to 20 tracks can be stored in

the memory in any order.

1. In stop mode, press PROG (on remote control) to enter programme setting.

™ PROG will flash on the display.

2. Press digits 0 - 9 on the remote control or

/ §

to select the desired track.

3. Press PROG to store the select track. The number “XXX” represents the track no.

•

Repeat steps 1 to 3 to store other tracks.

4. Press 9 to end programme setting.

™ PROG will remain on the display.

•

Press PROG (on remote control) in stop mode to review the programme sequence.

5. Press

to play the programmed tracks.

•

If you press REPEAT during programme playback, the current track or all programmed tracks will

be played repeatedly.

™ REPEAT/REPEAT ALL icon and PROG will appear on the display.

6. Press 9 in stop mode to clear the programme.

™ PROG will disappear from the display.

Notes : -The programming is automatically cleared as soon as the CD compartment is opened.

- The function of programme setting is disabled in PLAY/PAUSE mode.

- Programme cannot be used for VCDs when PBC is switched on. Switch off PBC before

storing tracks from such a VCD.

For MP3-CD only

1. In stop mode, press

PROG

on the remote control to enter programme setting.

™

PROG

will start flashing and " P01" will be displayed.

™ On TV screen, "PROG" program list (5 lines per page) will be displayed.

2. Press digits 0 - 9 on the remote control or

¡ / ™

to select the desired album.

3. Press

PROG

to store the select album. The number “AXX” represents the album no.

4. Press

/ §

repeatedly (or digits 0 - 9 on the remote control) to select the desired TRACK for

programming.

5. Press

PROG

to store the select track.

™ PROG will remain on the display.

•

Repeat steps 1 to 5 to store other desired album and track.

6. Press 9 to end programme setting.

•

Press

PROG

in stop mode can review the programme sequence.

7. Press 2 to start programme playback. You can press

/ §

to select the programmed track to

play.

8. Press 9 once stop programme playback or twice to clear the programme.

PROGRAMMING TRACKS

INSTRUCTIONS FOR USE

CD/VCD/MP3-CD

English

™ On TV screen, the total ALBUM and TRACK number will display, also with the album list (max.

10 lines per page). The current selected music is highlighted.

Notes : - To ensure good system performance, wait until the disc completely reads before

proceeding.

- For MP3-CD, the disc reading time may exceed 1 minute due to the large number of

songs compiled into one disc.

1. Press

to start playback.

™ The track number of the current track and

appear on the

display.

•

To interrupt playback, press

™

will disappear and the current track number will start flashing.

•

To resume playback, press

again.

2. To stop playback, press 9.

To select a desired track

•

Press

or §

on the set repeatedly (or use digits 0 - 9 buttons on the remote control) until the

desired track appears on the display.

•

If playback is stopped, press

to start playback.

To search for a particular passage during playback

•

Press and hold

or §

on the set for 1 second (or on the remote

control,press

5 or 6

)

™ During searching, the volume will be muted.

For MP3-CD only

To select a desired album

•

On the remote control, press

¡ or ™

until the desired album number appear on the display.

™ "AXX" will be displayed.

™ On TV screen, the arrow will move forward/backward in the ALBUM menu.

To select a desired track

•

Press

or §

on the set repeatedly (or on the remote control, press

or §

) to select a desired

track from the current album.

™ "XXX" will be displayed.

™ On TV screen, the arrow will move forward/backward in the TRACK menu.

•

Use the digital keys on the remote control to select the track under current album directly.

To select and playback another track during playback mode

1. Press

or §

repeatedly to select another track.

™ The new selected track will show on the display screen and TV screen and playback

continuously.

2. Press

to start playback the new selected track.

For VCD only

• Either p

ress

on the remote control repeatedly to select fast search speed (x1, x2, x3 or x4)

press & hold

or §

on the set for 1 second and then release

or §

to select fast search speed

(x1). Repeat this step to select other speed (x2, x3, x4).

SELECTING A DESIRED TRACK/PASSAGE

VCD

MP3

PLAYING A NORMAL DISC

3 - 5

CD/VCD/MP3-CD

English

Playing a Video CD with PBC

VCD with PBC (Playback Control) will be indicated on your TV screen as soon as they are inserted.

PBC is a predefined play sequence stored on the VCD.

1. Switch on the TV, insert a VCD with PBC.

2. Menu appears on the TV screen.

If the menu consists of a list of titles, you can select a sequence directly

1. Press digits 0 - 9 on the remote control to select your choice.

™ The VCD starts playing of the selected sequence automatically.

2. Press RETURN on the remote control to go back to the previous menu.

Note : - If a menu consists of more than one page, press

/ §

to go through the pages.

Switching off PBC

•

In stop mode, press PBC.

™ On TV screen, "PBC OFF" will be displayed shortly.

Notes : - Programme mode is not available whenever PBC mode is switched on.

- The menu structure depends on the programme stored on the VCD. Please refer to the

information supplied with the disc.

Pause

1. During playback, press

to have a still picture on the TV screen.

™ The sound will be muted.

™ On TV screen, "PAUSE" will be displayed.

2. Press

again to continue playback.

Goto

1. Press GOTO on the remote control.

™ On TV screen, "GOTO --:--" will be displayed.

2. Press digits 0 - 9 on the remote control to key in the disc time which you want the disc to begin

playback.

Note : - The disc time entered should not be greater than the total disc time.

- Goto mode is not available whenever PBC mode is switched on.

Slow

1. Press SLOW on the remote control to watch a VCD at a slower speed. There are 4 types of slow

modes to select.

™ The sound will be muted.

™ On TV screen, "SLOW 1/2", "SLOW 1/4", "SLOW 1/8" or "SLOW 1/16" will be displayed.

2. To resume playback at normal speed, press SLOW repeatedly until "PLAY" appears on the TV

screen or press

A-B repeat

This feature is also applicable to audio CD (except for MP3-CD). To Play a certain scene or passage

of the disc repeatedly.

VIDEO CD

INSTRUCTIONS FOR USE

CD/VCD/MP3-CD

English

You can play all the tracks in random order.

1. During playing, pause or stop mode, press SHUFFLE to enable SHUFFLE play mode.

™ SHUFFLE will appear on the display.

2. To exit shuffle mode, press SHUFFLE again or 9.

™ SHUFFLE will disappear from the display.

Note : - If the Shuffle function enabled, and the Repeat function is set on, will disable the Shuffle

play mode.

You can play the current track or the whole disc repeatedly.

1. During CD/ MP3-CD playing or pause mode, press REPEAT on the remote control or on the set.

™ REPEAT icon - to repeat the current track.

™ REPEAT ALL icon all- to repeat the whole disc.

2. To exit the repeat mode, press REPEAT until the REPEAT/REPEAT ALL icon disappears from

the display.

Notes : - If the Repeat function is enable, and the Shuffle function is set on, will disable all the

Repeat play modes.

- If the Repeat function is enable, and the Stop button is pressed, will disable all the

Repeat play modes.

Adjusting the TV System

Before viewing the Video CD, ensure that the set is switched to corresponding PAL or NTSC system

of your TV set (exception Multi - system TV).

1. On the remote control, press NTSC/PAL to switch between NTSC and PAL TV system.

OSD - On Screen Display

If you insert VCD/CD, your TV screen will serve as an additional display for messages (e.g. PLAY,

STOP), and information stored on the VCD/CD.

•

Press OSD on the remote control to select viewing various information.

™ The current track and current /elapsed time in the track/disc appear on the display.

VIDEO CD

REPEAT

SHUFFLE

3 - 6

CD/VCD/MP3-CD

English

This set can play a mixed mode disc.

– mixture of audio CD and MP3-CD

– mixture of other combination may not be operated normally.

1. As default, audio CD tracks will be read first.

™ will be displayed.

™ TV screen, "MIX, CD-DA" will be displayed.

2. Press

MIX/SEL

(on the remote control) repeatedly to select other

disc modes.

• MP3-CD:

™ MP3 is displayed.

™ TV screen, MP3 menu is displayed.

Notes : - For protected CDs, “MIX CD-DA” is displayed on your TV screen even if the disc does

not have other format. The

MIX/SEL

normal functions are not available for protected

CDs.

PLAYING A MIXED MODE DISC

VCD

MP3

INSTRUCTIONS FOR USE

CD/VCD/MP3-CD

English

1. Press A-B on the remote control during playback to mark the start point of the chosen scene or

passage.

™ "REPEAT A" will appear on the screen.

2. Press A-B again to mark the end of the chosen scene or passage.

™ "REPEAT AB" will appear on the screen.

™ The selected scene or passage will start playing repeatedly.

3. Press A-B once more to return to normal playback.

™ "REPEAT AB" will disappear from the display.

Notes : - You can also cancel A-B repeat by pressing

- A-B repeat marking can cross from one track to another. But for VCD 2.0, you are only

able to set the A-B repeat marking within the same track.

Resume

•

In stop mode, press RESUME on the remote control to start playback again from where you have

stopped.

Note : - Resume will not be available if you have changed the disc, opened the disc tray or

disconnected the system from the power supply.

View

This feature allows you to scan through a VCD for a quick review. PBC mode must be switched off.

1. In stop mode, press VIEW on the remote control to go to disc view function.

™ On TV screen, up to 9 pictures will be displayed. If a menu consists of more than one page,

press

to view the previous/next page.

™ The first several seconds of each track will be played.

To exit review mode, press digits 0 - 9 to play the desired track or

to play the current

selected track.

2. In playback mode, press VIEW on the remote control to go to track view function.

™ press

to select the track.

™ On TV screen, up to 9 pictures within the track will be displayed.

™ The first several seconds of each picture will be played.

To exit review mode, press digits 0 - 9 to play the desired position within the track or

play the current selected position.

Note : - If the disc is AVCD disc and there're no video tracks on the same viewed page, cannot use

the direct digital key to play the track.

Return

•

Press RETURN on the remote control to return to the previous VCD disc MENU level. It is

functional only for Video CD when PBC is switched on.

R/L/ST

You can use it to select the different audio modes.

•

Press R/L/ST on the remote control repeatedly to select the following modes:

on the LCD represents channel left/channel right / dual channel on a bilingual

VCD or mono left / mono right / stereo on single language VCD.

VIDEO CD

+ 21 hidden pages

Philips AZ-5130 Service manual

TABLE OF CONTENTS

HANDLING CHIP COMPONENTS

TECHNICAL SPECIFICATIONS

SERVICE MEASUREMENT

CONNECTIONS AND CONTROLS

INSTRUCTIONS FOR USE