Philips AZ1316/00C User Manual

Page 1
AZ1316MP3-CD Soundmachine
Printed in China AL/JW-0502
W
AZ 1316
http://www.audio.philips.com
User Manual Manuel d'utilisation Manual del usario Benutzerhandbuch
CLASS 1
LASER PRODUCT
Page 2
This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows:
• Remove fuse cover and fuse.
• Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved type.
• Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the dis­tribution board should not be greater than 5A.
Note: The severed plug must be disposed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accor-dance with the following code: BLUE – "NEUTRAL" ("N") and BROWN – "LIVE" ("L"). As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows:
• The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK.
• The BROWN wire must be connected to the terminal which is marked with the letter "L" or coloured RED.
• Do not connect either wires to the earth terminal in the plug which is marked by the letter "E" or by the safety earth symbol or coloured green or green-and-yellow.
Before replacing the plug cover, make certain that the cordgrip is clamped over the sheath of the lead – not simply over the two wires.
Copyright in the U.K. Recording and playback of material may require consent. See Copyright Act 1956 and The Performer’s Protection Acts 1958 to 1972.
Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materi­als:cardboard, expandable polystyrene, polyethylene. Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging, exhausted batteries and old equipment.
This set complies with the radio interference requirements
of the European Union.
Fitting a mains plug (U.K. only)
Page 3
A
C
M
A
I
N
S
~
1
2 3 4
5
7
8
9
6
0
! @
See A
VOLUM
E
SEARCH
ALBUM
/PRESET
TUNING
REPEAT
SHUFFLE
SEARCH
1
9
8
6
7
2
4
3
5
+
-
1
PRESET
MHz
FM
TUNER
2
CD
TRK ALB
MP3
3
CD
REP
PROG
ALL
TRK
MP3
CD
SHUF
TRK
CD
PROG
TRK ALB
MP3
6
CD
PROG
TRK ALB
MP3
7
8
A AB
C
9
X
A
4
5
Page 4
English CONTROLS/POWER SUPPLY
Using AC Mains 1 Check if the mains supply, as shown on the type
plate located on the bottom of the set, corre-
sponds to your local mains supply. If it does not, consult your dealer or service centre.
2 If your set is equipped with a voltage selector,
adjust the selector so that it matches with the local mains.
3 Connect the mains lead to the wall socket. 4 To disconnect the mains supply, unplug the set
from the wall socket.
The type plate is located on the bottom of the set. IMPORTANT! For users in the U.K.: please follow the instruc­tions on the upper righthand-side.
Helpful hints:
– To avoid unnecessary energy consumption,
always adjust the source selector to TAPE/OFF after using the set. Also check that the tape deck keys are released.
BASIC FUNCTIONS
Switching on and off and selecting function 1 To switch on, adjust the source selector to
CD/MP3, MW, FM or TAPE/OFF as desired.
2 To switch off, adjust the source selector to
TAPE/OFF and check the cassette keys are
released.
Helpful hints:
–To change from TAPE to FM, MW or
CD/MP3
function, or when you are switching off the set: first, make sure you press the tape
0 9
key to end
playback and all the cassette keys are released.
– The tone, sound settings, tuner presets and the
volume level (up to a maximum volume level of 20) will be retained in the set’s memory.
Adjusting volume and sound
1. Adjust the volume with the
VOL 3, 4controls. (or
VOLUME +, on the remote control)
Display shows and the volume level in
number from 00-32.
2. Press DBB once or more to select dynamic bass
boost on or off. Display: shows when activated.
DIGITAL TUNER
Tuning to radio stations
1 Push the source selector to MW or FM.
is displayed briefly and then the radio sta-
tion frequency, waveband and, if programmed, a preset number are shown. (See 2)
2 Press and hold ∞ or § until the frequency in the
display starts running. The radio automatically tunes to a station of suf-
ficient reception. Display shows dur­ing automatic tuning.
3 Repeat step 2 if necessary until you find the
desired station.
•To tune to a weak station, press ∞ or § briefly and repeatedly until you have found optimal recep­tion.
To improve radio reception:
• For FM, extend, incline and turn the telescopic aer­ial. Reduce its length if the signal is too strong.
• For MW, the set uses a built-in aerial. Direct this aerial by turning the whole set.
Programming radio stations
You can store up to a total of 20 radio stations in the memory (10 FM and 10 MW), manually or automati­cally (Autostore).
Manual programming 1 Tune to your desired station (see Tuning to radio
stations).
2 Press PROG to activate programming.
Display: PROG flashes.
3 Press
-, +
(on the remote control 3,4) once or
more to allocate a number from 1 to 10.
4 Press PROG to confirm. 5 Repeat steps 1-4 to store other stations. Helpful hints: You can erase a preset station by
storing another frequency in its place.
Autostore
Autostore automatically starts programming radio sta­tions from preset 1. Any previous presets e.g. manual­ly programmed will be erased.
1 Select MW or FM. 2 Press PROG until flashes.
Available stations are programmed (MW or FM).
After all stations are stored, the first autostore
preset station will then automatically play.
To listen to a preset or autostore station Press the ALBUM/PRESET
-, +
(on the remote con­trol 3,4) buttons once or more until the desired pre­set station is displayed.
SUPPLIED ACCESSORIES
– AC mains lead – remote control
TOP AND FRONT PANELS (See 1)
1 PUSH TO OPEN - press to open/close CD door 2 PROG -
CD/MP3:
programs tracks and reviews the program
MW/FM:
programs preset radio stations
3 MODE - selects different play modes: e.g. REP or
SHUF (random order)
4 VOL 3 , 4 - adjusts volume level
ALBUM/PRESET + ,- (up, down) -
MP3 only: selects albums MW/FM: selects a preset radio station
5 Display - shows the status of the set 6 2; - starts or pauses CD playback.
9 - stops CD playback;
- erases a CD program
, § TUNING DOWN, TUNING UP - CD/MP3: - searches backward and forward within a
track;
- skips to the beginning of a current track/ previous/ later track
MW/FM: -
tunes to radio stations
7 DBB (DYNAMIC BASS BOOST) -tu
rns the bass
enhancement on / off
8 CASSETTE RECORDER keys:
RECORD 0 - starts recording PLAY 1 - starts playback SEARCH 5 / 6 - fast winds/ rewinds tape. STOP•OPEN 0 9 - stops the tape;
- open the cassette compartment
PAUSE ; - pauses playback or recording
9
Source selector:
CD/MP3,
MW, FM
, TAPE/OFF
selects CD/MP3-CD, radio or tape source of sound;
switches off the set
BACK PANEL
0 Telescopic aerial - improves FM reception ! Battery compartment - for 6 batteries, type
R-14, UM2 or C-cells
@ AC MAINS - inlet for mains lead.
REMOTE CONTROL
1 VOLUME
+, – adjusts volume level (up, down)
2 SHUFFLE – plays all CD tracks in random order 3 2; – starts/ pauses CD playback 4 SEARCH 5, 6 – searches backwards/ forwards
within a track
5
ALBUM/
PRESET 3,4
MP3 only: selects albums MW/FM:
selects a preset radio station (up, down)
6 TUNING ∞, § – tunes to tuner stations 7 9 – stops CD playback;
– erases a CD programme
8 ¡, – skips to the beginning of a current track
previous/ subsequent track
9 REPEAT –selects repeat modes
CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
MAINS SUPPLY
Whenever convenient, use the mains supply to con­serve battery life. Make sure you remove the power plug from the set and wall socket before inserting batteries.
Batteries (not included) Main set (See 1)
• Insert 6 batteries, type R-14, UM2 or C-cells,
(preferably alkaline) with the correct polarity.
Remote control (See A)
• Insert 2 batteries, type AAA, R03 or UM4 (prefer-
ably alkaline).
Incorrect use of batteries can cause electrolyte leak­age and will corrode the compartment or cause the batteries to burst.
Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set.
• When inserting new batteries, do not try to mix old batteries with the new ones.
Batteries contain chemical substances, so they should be disposed of properly.
POWER SUPPLY/BASIC FUNCTIONS DIGITAL TUNER
Page 5
CD PLAYER
About MP3
The music compression technology MP3 (MPEG1 Audio Layer 3) significantly reduce the digital data of an audio CD while maintaining CD quality sound.
Getting MP3 files: you can either download legal
music files from the internet to your computer hard disc, or create such files by converting audio CD files in your computer through appropriate encoder software. (128kbps bit rate or higher is recom­mended for MP3 files.)
Creating a MP3 CD: burn the music files from
your computer hard disc on a CDR or CDRW using your CD burner.
Helpful hints:
Make sure that the file names of the MP3 files end
with .mp3.
Total number of music files and albums: around 350 (with a typical file name length of 20 characters)
The length of file names affects the number of
tracks for playback. With shorter file names, more files can be burned on a disc.
Playing a CD
This player plays Audio Discs including CD-R/ CD-RW, and MP3 CD. Do not try to play a CD-ROM, CD-I, CDV, VCD, DVD or computer CD.
IMPORTANT!
CDs encoded with copyright protection tech-
nologies by some record companies may be
unplayable by this product.
For a disc with CD Audio tracks and MP3
files, the MP3 files may be unplayable, depending on the encoding software.
Total number of albums + tracks: Max. 500
(for MP3)
1 Push the source selector to CD/MP3. 2 Insert a CD with the printed side facing up and
close the CD door. is displayed as the CD player scans the contents of a disc and then Audio CD: total playing time and total number of tracks appear. MP3: total number of tracks/albums appear. (See
3)
3 Press 2; to start playback. 4 To pause playback press 2;. Press 2; again to
resume play.
5 To stop CD playback, press 9.
Helpful hints: CD play will also stop when:
– the CD door is opened – the CD has reached the end – you select tuner or tape source.
Selecting a different track
• Press or § (on the remote control ¡ or ) once or repeatedly until the desired track number appears in the display.
For MP3-CD: first press ALBUM/PRESET
-, +
(on the remote control 3,4) once or more to find your album.
• In the pause/stop position, press 2; to start play­back.
Finding a passage within a track
1 During playback, press and hold or § (or
SEARCH 5, 6 on the remote control).
The CD is played at high speed and low volume.
2 When you recognize the passage you want, release
or § to resume normal playback.
Different play modes: SHUFFLE and REPEAT
(See 4, 5) You can select and change the various play modes before or during playback, and combine REP ALL and
REP with PROG.
SHUF – tracks of the entire CD are played in ran-
dom order
REP ALL – repeats the entire CD/program REP – plays the current track continuously
For MP3 only:
REP ALB – all tracks of current album play repeat-
edly.
1 To select play mode, press MODE (SHUFFLE or
REPEAT on the remote control) once or more.
2 Press 2; to start playback if in the stop position. 3 To select normal playback, press MODE repeatedly
until the various modes are no longer displayed. – You can also press 9 to cancel your play mode.
Helpful hints: In shuffle mode, press ∞ ( ¡ on the
remote control) to go to the beginning of current
track
Programming track numbers
You may store up to 20 tracks (for MP3-CD: 10 tracks) in the desired sequence. If you like, store any track more than once.
1 In the stop position, press ∞ or § (on the remote
control ¡ or ) to select your desired track num­ber.
For MP3-CD: first press ALBUM/PRESET
-, +
(on the remote control 3,4) once or more to find your album.
2 Press PROG. Display first shows the number of program location
and then, track/album number stored here. (See 6, 7)
If you attempt to program without first selecting a
track number, is shown.
3 Repeat steps 1-2 to select and store all desired
tracks.
Display: if you try to program more than
20 tracks (for MP3-CD: 10 tracks).
Helpful hints:
When the
PROG
or
SHUF
mode is active, use of
the - , +keys (or
3,4 on the remote control)
are
void.
Reviewing the programme
In the stop position, press PROG repeatedly to see your stored track numbers. Display first shows the number of program location and then, track/album number stored here.
Erasing a programme
You can erase the contents of the memory by:
• opening the CD door;
• selecting MW, FM or TAPE sound sources;
•pressing
9
twice during playback or once in the
stop position.
PROG disappears.
CASSETTE RECORDER
Cassette playback
1 Push the source selector to TAPE.. 2 Insert a cassette and close the door. 3 Press PLAY 1 to start playback.
Display: shows throughout tape opera­tion.
4 To pause, press PAUSE ;. Press again to resume. 5 To stop the tape, press STOP/OPEN 9/.
Fast forwarding/rewinding
1 Press SEARCH 5 or 6 until you reach your
desired passage.
2 Press
9
/ to stop fast forwarding/rewinding.
Helpful hints:
– During playback, the keys are automatically
release at the end of a tape, and the set is switched off (except if
;
has been activated).
– During fast winding/rewinding, the keys will not
be released at the end of a tape. To switch off the set, make sure the cassette keys are also released.
GENERAL INFORMATION ON RECORDING
• Recording is permissible insofar as copyright or. other rights of third parties are not infringed.
• For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken. This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes.
• The best recording level is set automatically. Altering the VOL or DBB controls will not affect the recording.
•To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape.
TAPE
DIGITAL TUNER CD/MP3 PLAYER CD/MP3 PLAYER CASSETTE RECORDER
Page 6
CD Synchro Start recording
1 Select CD/MP3 function. 2 Insert a CD and if desired, programme track num-
bers.
3 Open the cassette door. 4 Insert a suitable tape into the cassette deck and
close the door.
5 Press RECORD 0 to start recording.
Playing of the CD/program starts automatically
from the beginning. You don’t need to start the CD player separately.
Display: shows briefly.
6 To pause recording, press PAUSE ;.
Press PAUSE ; again to resume recording.
7 To stop recording, press STOP/OPEN 9/.
Recording from the Radio
1 Tune to the desired radio station (see Tuning to
radio stations).
2 Follow steps 3-7, under CD Synchro Start record-
ing.
Maintenance & Safety (See 8, 9)
CD player and CD handling
• If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates.
• Always close the CD door to avoid dust on the lens.
•To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc.
• Never write on a CD or attach any stickers to it.
Safety Information
• Place the set on a hard, flat and stable surface so that the system does not tilt.
• Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight.
• The apparatus shall not be exposed to dripping or splashing.
• Adequate ventilation with a minimum gap of 15 cm between the ventilation holes and surrounding surfaces is necessary to prevent heat build-up.
• The ventilation should not be impeded by cover­ing the ventilation openings with items, such as newspapers, table-cloths, curtains, etc..
• No objects filled with liquids, such as vases, shall be placed on the apparatus.
• No naked flame sources, such as lighted candles, should be placed on the apparatus.
• The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated.
•To clean the set, use a dry cloth. Do not use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the housing.
Tape deck maintenance
To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alco­hol or a special head cleaning fluid to clean the deck.
1 Open the cassette door. 2 Press PLAY 1 and clean the roller C. 3 Press PAUSE ; and clean the heads A, and the
capstan B.
4 After cleaning, press STOP/OPEN 9/.
Remote control does not function properly
– Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle
No sound /power
–Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
Severe radio hum or noise
– Electrical interference: set too close to TV, VCR or
computer
• Increase the distance
Poor radio reception
–Weak radio signal
• FM: Adjust the FM telescopic aerial
indication
– CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
– Laser lens steamed up
•Wait until lens has cleared
– CD-R/CD-RW is blank/ not finalized
• Use a finalized CD-R(W)
– CD-ROM disc inserted/
CD contains non-audio files
• Use CD Audio discs/MP3-CD only/ press or § once or more to skip to a CD audio track instead of the data files
Note: Make sure the CD is not encoded with Copyright protection technologies, as some do not con­form to the Compact Disc standard.
The disc skips tracks
Disc damaged or dirty
Replace or clean disc
SHUF
or
PROG
is active
Switch off
SHUF/PROG
Note: For a disc with CD Audio tracks and MP3 files, the MP3 files may be unplayable, depending on the encoding software.
Sound skips during MP3 playback
–MP3 file made at compression level exceeding
320kbps
• Use a lower compression level to record CD tracks into MP3 format
Disc damaged or dirty
• Replace or clean disc
Poor cassette sound quality
– Dust and dirt on the heads, etc.
• Clean deck parts, see Maintenance
– Use of incompatible cassette types
(METAL or CHROME)
• Only use NORMAL (IEC I) for recording
Recording does not work
– Cassette tab(s) may be broken
• Apply adhesive tape over the missing tab space
WARNING
Do not open the set as there is a risk of electric shock! Under no circumstances should you try to repair the set yourself, as this will invalidate the guarantee.
If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
CASSETTE RECORDER MAINTENANCE & SAFETY
TROUBLESHOOTING
Loading...