Philips AC1214 User Manual [ml]

© 2018 Koninklijke Philips N.V. All rights reserved.
4241 210 98944
AC1214
D
C
1 2
A B
I
J K L N OM
H
E
EN User manual 1
DA Brugervejledning 19
DE Benutzerhandbuch 37
ES Manual del usuario 57
FI Käyttöopas 77
IT Manuale utente 116
NL Gebruiksaanwijzing 136
NO Brukerhåndbok 155
SV Användarhandbok 173
F
G
3s
3s
3s
3s
Contents
English
1 Important 2
Safety 2
2 Your air purier 5
Product overview (Fig.a) 5 Controls overview (Fig.b) 5
3 Getting started 5
Installing the lters 5 Wi-Fi connection 6
4 Using the air purier 7
Understanding the air quality light 7 Turning on and o 7 Changing the fan speed 7 Light sensor 8 Night sensing mode 8 Setting the child lock 9
5 Cleaning 9
Cleaning the body of the air
purier 9 Cleaning the air quality sensor 10 Cleaning the pre-lter 10
8 Troubleshooting 14
9 Guarantee and service 17
Order parts or accessories 17
10 Notices 17
Electromagnetic elds (EMF) 17 Recycling 18 Software 18 Simplied EU declaration of
conformity 18
6 Replacing the lters 11
Filter replacement indicator 11 Replacing the lters 11 Filter reset 12
7 Storage 13
Environmental friendly paper used. Thanks for your contribution to save trees.
1EN
1 Important
Safety
Read this user manual carefully before you use the appliance, and save it for future reference.
Danger
Do not let water or any
other liquid or ammable detergent enter the appliance to avoid electric shock and/or a re hazard.
Do not clean the
appliance with water, any other liquid, or a (ammable) detergent to avoid electric shock and/ or a re hazard.
Do not spray any
ammable materials such as insecticides or fragrance around the appliance.
Warning
Check if the voltage
indicated on the appliance corresponds to the local power voltage before you connect the appliance.
If the power cord is
damaged, you must have it replaced by Philips, a service center authorized by Philips, or similarly qualied persons in order to avoid a hazard.
Do not use the appliance
if the plug, the power cord, or the appliance itself is damaged.
This appliance can be
used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Child shall not play with the appliance. Cleaning and maintenance shall not be made by children without supervision.
Do not block the air inlet
and outlet, e.g. by placing items on the air outlet or in front of the air inlet.
2 EN
Make sure that foreign
English
objects do not fall into the appliance through the air outlet.
Standard WiFi interface
based on 802.11b/g/n at
2.4 GHz with a maximum output power of 31.62 mW EIRP.
Caution
This appliance is not
a substitute for proper ventilation, regular vacuum cleaning, or use of an extractor hood or fan while cooking.
If the power socket used
to power the appliance has poor connections, the plug of the appliance becomes hot. Make sure that you plug the appliance into a properly connected power socket.
Always place and use
the appliance on a dry, stable, level, and horizontal surface.
Leave at least 20cm
free space behind and on both sides of the appliance and leave at least 30cm free space above the appliance.
Do not place anything on
top of the appliance.
Do not sit or stand on
the appliance. Sitting or standing on the appliance may lead to potential injury.
Do not place the
appliance directly below an air conditioner to prevent condensation from dripping onto the appliance.
Make sure all lters
are properly installed before you switch on the appliance.
Only use the original
Philips lters specially intended for this appliance. Do not use any other lters.
Combustion of the lter
may cause inreversible human hazard and/or jeopardize other lives . Do not use the lter as fuel or for similar purpose.
Avoid knocking against
the appliance (the air inlet and outlet in particular) with hard objects.
3EN
Always lift or move the
appliance by the handle on top of the appliance.
Do not insert your ngers
or objects into the air outlet or the air inlet to prevent physical injury or malfunctioning of the appliance.
Do not use this appliance
when you have used indoor smoke-type insect repellents or in places with oily residues, burning incense, or chemical fumes.
Do not use the appliance
near gas appliances, heating devices or replaces.
Always unplug the
appliance after use and before cleaning or carrying out other maintenance.
Do not use the appliance
in a room with major temperature changes, as this may cause condensation inside the appliance.
To prevent interference,
place the appliance at least 2 meters away from electrical appliances that use airborne radio waves such as TVs, radios, and radio-controlled clocks.
The appliance is only
intended for household use under normal operating conditions.
Do not use the appliance
in wet surroundings or in surroundings with high ambient temperatures, such as the bathroom, toilet, or kitchen.
The appliance does
not remove carbon monoxide (CO) or radon (Rn). It cannot be used as a safety device in case of accidents with combustion processes and hazardous chemicals.
If you need to move the
appliance, disconnect the appliance from the power supply rst.
Do not move the
appliance by pulling its power cord.
4 EN
2 Your air purifier
English
Congratulations on your purchase, and welcome to Philips!
To fully benet from the support that Philips oers, register your product at www.philips.com/welcome.
Product overview (Fig.a)
A Control panel
3 Getting started
Installing the lters
Note
Make sure the air purier is unplugged
from the electrical outlet before installing the lters.
Make sure the side of the lter with the
tag is pointing towards you.
B Air quality light C Air outlet D Air quality sensor
NanoProtect lter Series 3
E
(FY1410)
NanoProtect lter Active Carbon
F
(FY1413)
G Pre-lter H Air inlet
I Front panel
Controls overview (Fig.b)
J On/O button K Night sensing mode button L Display screen
M Wi-Fi indicator
N Fan speed button
O Child lock button
1 Pull the bottom part of the front
panel and gently lift to remove it from the air purier (Fig.c).
2 Press the clip down (1) and pull the
pre-lter towards you (2) (Fig.d).
3 Remove all lters (Fig.e). 4 Remove all packaging materials
from the lters (Fig.f).
5 Place the thick lter (FY1410)
into the air purier and then the thin active carbon lter (FY1413) (Fig.g). The model numbers are shown on each lter.
6 Attach the pre-lter back into the
air purier (Fig.h).
Note
Make sure the side with the clip is
pointing towards you, and that all hooks of the pre-lter are properly attached to the purier.
7 Reattach the front panel by pressing
the top part of the panel onto the top of the air purier (1). Then, gently push the panel against the body of the air purier (2) (Fig.i).
8 Wash your hands thoroughly after
installing lters.
5EN
Wi-Fi connection
Setting up the Wi-Fi connection for the rst time
1 Download and install the
"Air Matters" app from the App Store or Google Play.
2 Put the plug of the air purier in the
power socket and touch on the air purier.
» The Wi-Fi indicator blinks
orange for the rst time.
to turn
3 Make sure that your smartphone or
tablet is successfully connected to your Wi-Fi network.
4 Launch the "Air Matters" app and
click on "Connect an Air Purier or Monitor" on the top of the screen. Follow the onscreen instructions to connect the air purier to your network.
5 After the successful pairing and
connection, the Wi-Fi indicator
will light up white. If pairing
is not successful, consult the troubleshooting section, or the help section in the "Air Matters" App for extensive and up-to-date troubleshooting tips.
6 EN
Note
This instruction is only valid when
the air purier is being set up for the rst time. If the network has changed or the setup needs to be performed again, consult section "Reset the Wi-Fi connection" on page 6.
If you want to connect more than
one air purier to your smartphone or tablet, you have to do this one by one. Complete the set up of one air purier before you turn on the other air purier.
Make sure that the distance between
your smartphone or tablet and the air purier is less than 10 m without any obstructions.
This App supports the latest versions
of Android and iOS. Please check www.philips.com/purier-compatibility for the latest update of supported operating systems and devices.
Reset the Wi-Fi connection
Note
This applies when the default network
to which your purier is connected has changed.
Reset the Wi-Fi connection when your
default network has changed.
1 Put the plug of the air purier in the
power socket and touch on the air purier.
to turn
2 Touch and simultaneously for
3 seconds until you hear a beep.
» The air purier goes to pairing
mode.
» The Wi-Fi indicator blinks
orange.
3 Follow the steps 4-5 in "Setting up
the Wi-Fi connection for the rst time" section.
4 Using the air
English
purifier
Understanding the air quality light
Indoor Allergen Index (IAI) is a real-time numerical display that provides visual and immediate feedback on indoor allergen level.
IAI Air quality
light color
1-3 4-6 7-9 10-12
The air quality light automatically goes on when the air purier is switched on, and lights up all colors in sequence. After approximately 30 seconds, the air quality sensors select the color that corresponds to the surrounding air quality of airborne particles.
Blue Blue-Purple Purple-Red Red
Air quality level
Good Fair Poor Very poor
1 Put the plug of the air purier in the
power socket.
2 Touch to switch on the air purier
(Fig.j).
» The air purier beeps. » The air purier operates under
the auto mode by default.
» When the air purier is warming
up, " " displays on the screen.
» After measuring the air
quality for approximately 30 seconds, the air quality sensor automatically selects the appropriate air quality light color.
3 Touch and hold for 3 seconds to
switch o the air purier.
Note
If the air purier stays connected to
the electrical outlet after turning OFF, the air purier will operate under the previous settings when turned ON again.
If the air purier accidentally shuts o
during running, it restarts automatically and operates under previous settings when the power supply is resumed.
Turning on and o
Note
Always place the air purier on a
stable, horizontal, and level surface with the front of the unit facing away from walls or furniture.
For optimum purication performance,
close doors and windows.
Keep curtains away from the air inlet or
air outlet.
Changing the fan speed
There are several fan speeds available. You can choose the auto mode, speed
1, 2, 3 or turbo mode (t).
Auto (A)
Touch the fan speed button
repeatedly to select the auto mode (Fig.k).
7EN
Allergen mode
The specially designed allergen mode can eectively reduce common allergens such as pollen and pet dander.
Touch the fan speed button to
select the Allergen mode (Fig.l).
» Auto (A) and display on the
screen.
Manual
Touch the fan speed button
repeatedly to select the fan speed you need (Fig.m).
Turbo (t)
In turbo mode, the air purier operates on the highest speed.
Touch the fan speed button to select the turbo mode (t) (Fig.n).
Night sensing mode
You can activate the night sensing mode in two ways.
Activating the night sensing mode manually
Before you go to sleep, touch
manually to activate the night sensing mode (Fig.o).
» If the air quality light is blue,
the air purier directly goes to the night sensing mode. The air purier operates quietly and the air quality light will be dimmed.
» If the air quality light is not blue,
the air purier operates under turbo mode for a maximum of 10 minutes, the air quality light blinks slow during this time, and then goes to the night sensing mode.
Light sensor
With the light sensor, the air purier can work according to the ambient light.
When the ambient light dims for 10 seconds, all the lights on the control panel will turn o slowly. During this period, you can touch any of the buttons, all lights will turn on again. If you don't perform other operations within 10 seconds, all lights will turn o.
After the ambient light becomes bright and lasts at least for 10 seconds, all lights will turn on again.
8 EN
Auto activating the night sensing mode
When the air purier operates in auto mode or allergen mode, if the light sensor detects the lights in your room are turned o, the air purier goes to the night sensing mode automatically. The air purier will adjust the fan speed in real-time to make sure the air in your room is good. The air quality light will be dimmed.
Note
English
The light sensor detects the lights in
your room after 11 hours in the night sensing mode.
If the lights in your room are turned
on, the air purier will quit the night sensing mode and operate under the previous mode. The air quality light and the display will be on again.
To exit the night sensing mode
manually, touch or button.
Setting the child lock 1 Touch and hold the child lock
button for 3 seconds to activate child lock (Fig.p).
» The child lock icon displays
on the screen.
» When the child lock is on,
all the other buttons are not responsive, only the child lock icon blinks.
2 Touch and hold the child lock
button for 3 seconds again to deactivate child lock (Fig.q).
» The child lock icon
disappears.
Note
The child lock function is automatically
unlocked when the pre-lter cleaning code or the lter replacement code displays on the screen.
5 Cleaning
Note
Always turn the air purier o and
unplug the air purier from the electrical outlet before cleaning.
Never immerse the air purier in water
or any other liquid.
Never use abrasive, aggressive, or
ammable cleaning agents such as bleach or alcohol to clean any part of the air purier.
Only the pre-lter is washable. The air
lter is not washable.
Do not attempt to clean the lters or
air quality sensor with a vacuum.
Cleaning the body of the air purier
Regularly clean the inside and outside of the air purier to prevent dust from collecting.
1 Use a soft, dry cloth to clean both
the interior and exterior of the air purier.
2 The air outlet can also be cleaned
with a dry, soft cloth.
3 Detach the front cover from the air
purier and wash it under running tap water.
9EN
Cleaning the air quality sensor
Clean the air quality sensor every 2 months for optimal functioning of the purier.
Note
If the air purier is used in a dusty
environment, it may need to be cleaned more often.
If the humidity level in the room is
very high, condensation may develop on the air quality sensor and the air quality light may indicate a more poor air quality even though the air quality is actually good. If this occurs, clean the air quality sensor or use the air purier on a manual speed setting.
Cleaning the pre-lter
Clean the pre-lter when F0 is displayed on the screen (Fig.v).
1 Switch o the air purier and
unplug from the power socket.
2 Pull the bottom part of the front
panel and then gently lift to remove it from the air purier (Fig.c).
3 Press the clip down (1) and pull the
pre-lter towards you (2) (Fig.d).
4 If the pre-lter is very dirty, use a
soft brush to brush away the dust. Then wash the pre-lter under running tap water (Fig.w).
5 Allow the pre-lter to air dry
thoroughly before placing back in the air purier.
1 Switch o the air purier and
unplug from the power socket.
2 Clean the air quality sensor inlet
and outlet with a soft brush (Fig.r).
3 Open the air quality sensor cover
(Fig.s).
4 Clean the air quality sensor, the
dust inlet and the dust outlet with a damp cotton swab (Fig.t).
5 Dry all parts thoroughly with a dry
cotton swab.
6 Reattach the air quality sensor
cover (Fig.u).
Note
Always keep air quality cover closed
while the air purier is working.
10 EN
Note
To optimize the lifetime of the pre-
lter, make sure it dries completely after cleaning.
Wash your hands after handling the
lter.
6 Put the pre-lter back into the air
purier (Fig.h).
Note
Make sure the side with the clip is
pointing towards you, and that all hooks of the pre-lter are properly attached to the air purier.
7 To reattach the front panel, press
English
the top part of the panel onto the top of the air purier (1). Then, gently push the panel against the body of the air purier (2) (Fig.i).
8 Put the plug of the air purier in the
power socket.
9 Touch and hold the for
3 seconds to reset the pre-lter cleaning time (Fig.x).
10 Wash your hands thoroughly after
installing lters.
6 Replacing the
filters
Filter replacement indicator
This air purier is equipped with a lter replacement indicator to make sure that the air purication lter is in optimal condition when the air purier is operating. When the lters need to be replaced, the lter code displays on the screen.
If the lters are not replaced in time, the air purier will stop operating and automatically lock.
Replacing the lters
Note
The air purication lters are not
washable nor vacuum cleanable.
Always turn o the air purier and
unplug from the electrical outlet before replacing the lters.
Do not clean the lters with a vacuum
cleaner.
If the pre-lter is damaged, worn or
broken, do not use. Visit www.philips.com/support or contact the Consumer Care Center in your country.
11EN
Filter alert light status
A3 displays on the screen
C7 displays on the screen
A3 and C7 display on the screen alternately
Action
Replace NanoProtect lter Series 3 (FY1410)
Replace NanoProtect lter Active Carbon (FY1413)
Replace both lters
1 Turn o the air purier and unplug
from the power socket.
2 Take out the used air lter according
to the lter alert light status displayed on the screen (Fig.y). Discard used lters.
Note
Do not touch the pleated lter surface,
or smell the lter as it has collected pollutants from the air.
3 Remove all packaging material from
the new lter (Fig.f).
4 Place the new lters into the air
purier (Fig.g).
5 Put the plug of the air purier in the
power socket.
6 Touch and hold the for 3 seconds
to reset the lter lifetime counter (Fig.z).
7 Wash your hands after changing a
lter.
Filter reset
You can replace lters even if there is no lter replacement code displayed on the screen. After replacing a lter, you need to reset the lter lifetime counter manually.
1 Touch and simultaneously for
3 seconds to enter the lter reset mode (g.{).
» Code (A3) of the NanoProtect
lter Series 3 displays on the screen.
2 Touch and hold for 3 seconds to
force reset the lter lifetime counter of the NanoProtect lter Series 3 (g.z).
3 Code (C7) of the Nanoprotect lter
Active Carbon displays on the screen after the lifetime counter of the NanoProtect lter Series 3 has been reset (g.|).
4 Touch and hold for 3 seconds to
force reset the lter lifetime counter of the NanoProtect lter Active Carbon and exit the lter reset mode (g.}).
12 EN
7 Storage
English
1 Turn o the air purier and unplug
from the power socket.
2 Clean the air purier, air quality
sensor and pre-lter (see chapter ‘Cleaning’).
3 Let all parts dry thoroughly before
storing.
4 Wrap the lter and pre-lter
separately in air tight plastic bags.
5 Store the air purier, the lter and
pre-lter in a cool, dry location.
6 Always thoroughly wash hands after
handling lters.
13EN
8 Troubleshooting
This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, contact the Consumer Care Center in your country.
Problem Possible solution
The air purier does not work even though it is plugged in to the power socket and switched on.
The air purier does not work even though it is switched on.
The air purier accidentally powers o.
The airow that comes out of the air outlet is signicantly weaker than before.
The air quality does not improve, even though the air purier has been operating for a long time.
Check if the front cover is properly installed.
The lter replacement code has been displaying on the
screen but you have not replaced the corresponding lter yet. The appliance will be locked if you keep using the expired lter. In this case, replace the lter and reset the lter lifetime counter.
The lter replacement indicator has been on continuously
but you have not replaced the corresponding lter, and the air purier is now locked. In this case, replace the lter and reset the lter lifetime counter.
The air purier restarts automatically and goes to the
previous mode when the power resumes.
The pre-lter is dirty. Clean the pre-lter (see chapter
"Cleaning").
One of the lters has not been placed in the air purier or
the lter is not placed properly. Make sure that all lters are properly installed in the following order, starting with the innermost lter:
1) NanoProtect lter Series 3 (FY1410); 2) NanoProtect lter Active Carbon (FY1413) 3) pre-lter.
The air quality sensor is wet. Make sure that the air quality
sensor is clean and dry (see chapter "Cleaning").
The color of the air quality light always stays the same.
14 EN
The air quality sensor is dirty. Clean the air quality sensor
(see chapter "Cleaning").
Problem Possible solution
English
The lter may produce smell after being used for a while
because of the absorption of indoor air. Remove the lter
The air purier produces a unpleasant smell.
and place it where it has direct sunlight and ventilation for several hours. Re-install and try using it again. If the odor remains, please replace the lter.
If the air purier produces a burnt odor, switch OFF and
unplug from the electrical outlet. Contact Consumer Care Center in your country.
If the air purier is too loud, change the fan speed to a The air purier is loud.
lower fan speed level. When using the air purier in a bedroom at night, choose the night sensing mode or select a lower fan speed level.
The air purier still indicates that I need to replace a lter, but I already
Perhaps you did not reset the lter lifetime counter. Plug
in the air purier, touch to switch on the air purier, and touch and hold the for 3 seconds.
did.
Error codes "E1", "E2", "E3" or "E4" displays on the
The appliance has malfunctions. Contact the Consumer
Care Center in your country.
screen.
Which App I should download?
Please download and install the 'Air Matters' App
developed by FreshIdeas Studio from the App Store or
Google Play.
15EN
Problem Possible solution
If the router your purier is connected to is dual – band
and currently it is not connecting to a 2.4GHz network, please switch to another band of the same router (2.4GHz) and try to pair your purier again. 5GHz networks are not supported.
Web authentication networks are not supported.
Check if the purier is within range of the Wi-Fi router. You
can try to locate the air purier closer to the Wi-Fi router.
Check if the network name is correct. The network name is
case-sensitive.
The Wi-Fi setup is not successful.
Check if the Wi-Fi password is correct. The password is
case-sensitive.
Retry the setup with the instructions in section ‘Set up the
Wi-Fi connection when the network has changed’.
The Wi-Fi connectivity can be interrupted by electromagnetic
or other interferences. Keep the appliance away from other electronic devices that may cause interferences.
Check if the mobile device is in airplane mode. Make sure
to have the airplane mode deactivated when connecting to the Wi-Fi network.
Consult the help section in the App for extensive and up-
to-date troubleshooting tips.
16 EN
9 Guarantee and
English
service
10 Notices
If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Consumer Care Center in your country (you nd its phone number in the worldwide guarantee leaet). If there is no Consumer Care Centre in your country, go to your local Philips dealer.
Order parts or accessories
If you have to replace a part or want to purchase an additional part, go to your Philips dealer or visit www.philips.com/ support.
If you have problems obtaining the parts, please contact the Philips Consumer Care Center in your country (you can nd its phone number in the worldwide guarantee leaet).
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic elds.
Compliance with EMF
Koninklijke Philips N.V. manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.
One of Philips' leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.
Philips is committed to develop, produce and market products that cause no adverse health eects. Philips conrms that if its products are handled properly for their intended use, they are safe to use according to scientic evidence available today.
Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardization for early integration in its products.
17EN
Recycling
This symbol means that this product shall not be disposed of with normal household waste (2012/19/EU).
Follow your country’s rules for the separate collection of electrical and electronic products. Correct disposal helps prevent negative consequences for the environment and human health.
Software
App Store is a service mark of Apple Inc. Google Play is a trademark of Google
Inc. Air Matters app developed by Air
Matters Network Pty Ltd. This Philips appliance and Air Matters
app applied multiple open source softwares, copies of open source software license text used in this product can be derived from website: www.philips.com/purier-compatibility.
Simplied EU declaration of conformity
Hereby, Philips Consumer Lifestyle B.V. declares that the radio equipment type AC1214 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.philips.com.
Indhold
Dansk
1 Vigtigt 20
Sikkerhed 20
2 Din luftrenser 23
Produktoversigt (g.a) 23 Oversigt over
betjeningsknapper (g.b) 23
3 Kom godt i gang 23
Montering af ltre 23 Wi-Fi-forbindelse 24
4 Brug af luftrenseren 25
Forklaring af luftkvalitetslyset 25 Sådan tændes og slukkes
apparatet 25 Ændring af blæserhastighed 25 Lyssensor 26 Mørkesensortilstand 26 Indstilling af børnesikring 27
5 Rengøring 27
Rengøring af luftrenserens
kabinet 27 Rengøring af
luftkvalitetssensoren 28 Rengøring af forlteret 28
7 Opbevaring 31
8 Fejlnding 32
9 Garanti og service 35
Bestilling af dele eller tilbehør 35
10 Bemærkninger 35
Elektromagnetiske felter (EMF) 35 Genbrug 36 Software 36 Forenklede EU-
overensstemmelseserklæring 36
6 Udskiftning af ltrene 29
Indikator for udskiftning af lter 29 Udskiftning af ltre 29 Filternulstilling 30
Der er anvendt miljøvenligt papir. Tak for dit bidrag til redningen af træerne.
19DA
1 Vigtigt
Sikkerhed
Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i brug, og gem den til eventuelt senere brug.
Fare
Lad ikke vand eller
nogen andre væsker eller brandbare rengøringsmidler komme i berøring med apparatet for at undgå elektrisk stød og/eller brandfare.
Undlad at rengøre
apparatet med vand eller andre væsker eller (brandbart) rengøringsmiddel for at undgå elektrisk stød og/ eller brandfare.
Sprøjt ikke brændbare
materialer som f.eks. insektgift eller parfume omkring apparatet.
Advarsel
Kontrollér, om den
angivne netspænding på apparatet svarer til den lokale netspænding,
før du slutter strøm til apparatet.
Hvis netledningen
beskadiges, må den kun udskiftes af Philips, et autoriseret Philips­serviceværksted eller en tilsvarende kvaliceret fagmand for at undgå enhver risiko.
Brug aldrig apparatet,
hvis netstik, netledning eller selve apparatet er beskadiget.
Dette apparat kan bruges
af børn fra 8 år og opefter og personer med nedsatte fysiske, sensoriske eller mentale evner eller manglende erfaring og viden, såfremt de er blevet instrueret i sikker brug af apparatet og forstår de medfølgende risici. Lad ikke børn lege med apparatet. Rengøring og vedligeholdelse må ikke foretages af børn uden opsyn.
Luftind- og -udtagene må
ikke blokeres, f.eks. ved at stille ting på luftudtaget eller foran luftindtaget.
20 DA
Sørg for, at
Dansk
fremmedlegemer ikke falder ind i apparatet gennem luftudgangen.
Standard Wi-Fi-
grænseade baseret på 802.11b/g/n ved 2,4 GHz med en maksimal udgangseekt på 31,62 mW EIRP.
Forsigtig
Apparatet kan ikke
bruges som erstatning for grundig udluftning, støvsugning eller brug af emhætte eller udsugning under madlavning.
Hvis den anvendte
stikkontakt er dårlig, vil apparatets stik blive varmt. Sørg for, at du slutter apparatet til en ordentlig tilsluttet stikkontakt.
Anbring og brug altid
apparatet på et stabilt, plant og vandret underlag.
Der skal være mindst
20 cm fri plads bag ved og på begge sider af apparatet, og der skal være mindst 30 cm frirum over apparatet.
Placer ikke noget ovenpå
apparatet.
Du må ikke sidde eller
stå på apparatet. Hvis du sidder eller står på apparatet, kan du komme til skade.
Placer ikke apparatet
direkte under et klimaanlæg for at forhindre, at der drypper kondensvand på apparatet.
Sørg for, at alle ltre er
installeret korrekt, inden apparatet tændes.
Brug kun de originale
ltre fra Philips, der er særligt beregnede til dette apparat. Anvend ikke andre ltre.
Antænding af lteret kan
forårsage alvorlig fare for mennesker og/eller bringe andres liv i fare. Brug ikke lteret som brændsel eller lignende formål.
Undgå at støde mod
apparatet (særligt luftindtag og -udtag) med hårde genstande.
21DA
Løft eller yt altid
apparatet i håndtaget på toppen af apparatet.
Stik aldrig dine ngre eller
genstande ind i luftudtag eller luftindtaget for at undgå fysiske skader eller funktionsfejl af apparatet.
Brug ikke apparatet, når
du har anvendt et indendørs, rygende insektmiddel, eller på steder med olierester, brændende røgelse eller kemiske dampe.
Brug ikke apparatet
i nærheden af gasapparater, varmeapparater eller brændeovne/ kaminer.
Tag altid stikket ud af
stikkontakten efter brug og før rengøring eller anden vedligeholdelse.
Brug ikke apparatet
i rum med store temperatursvingninger, da det kan skabe kondens inde i apparatet.
Undgå interferens ved
at placere apparatet mindst 2 m fra elektriske apparater med luftbårne radiobølger, som f.eks. TV, radio og radiostyrede ure.
Apparatet er kun beregnet
til husholdningsbrug under normale driftsforhold.
Brug ikke apparatet i
våde omgivelser eller ved høje rumtemperaturer, som f.eks. bad, toilet eller køkken.
Apparatet fjerner ikke
kulilte (CO) eller radon (Rn). Det kan ikke bruges som en sikkerhedsenhed i tilfælde af ulykker med forbrændingsprocesser og farlige kemikalier.
Hvis du skal ytte
apparatet, skal du frakoble apparatet fra strømforsyningen.
Flyt ikke apparatet ved at
trække i netledningen.
22 DA
2 Din luftrenser
Dansk
Tillykke med dit køb, og velkommen til Philips!
Du kan få alle fordelene ved den support, som Philips yder, ved at registrere dit produkt på www.philips.com/welcome.
Produktoversigt (g.a)
A Kontrolpanel B Luftkvalitetslys C Luftudtag D Sensor til luftkvalitet
NanoProtect-lter i 3-serien
E
(FY1410)
NanoProtect-lteret Aktivt kulstof
F
(FY1413)
G Forlter H Luftindtag
I Frontpanel
3 Kom godt i gang
Montering af ltre
Bemærk
Kontroller, at stikket til luftrenseren er
taget ud af stikkontakten, før ltrene monteres.
Sørg for, at siden af lteret med
etiketten vender mod dig selv.
1 Træk den nederste del af
frontpanelet, og løft det forsigtigt for at fjerne det fra luftrenseren (g.c).
2 Tryk klemmen ned (1), og træk
forlteret ind mod dig selv (2) (g.d).
3 Fjern alle ltre (g.e). 4 Fjern al emballage fra ltrene (g.f). 5 Sæt det tykke lter (FY1410) ind i
luftrenseren og derefter ind i det tynde lter for aktivt kulstof (FY1413) (g.g). Modelnumrene vises på hvert lter.
6 Sæt forlteret tilbage i luftrenseren
(g.h).
Oversigt over betjeningsknapper (g.b)
J Afbryderknap K Mørkesensortilstandsknap L Display
M Wi-Fi-indikator
N Blæserhastighedsknap
O Børnesikringsknap
Bemærk
Sørg for, at siden med klemmen
peger ind mod dig, og at alle kroge på forlteret er korrekt fastgjort i renseren.
7 Sæt frontpanelet på igen ved at
klikke den øverste del af panelet fast på toppen af luftrenseren (1). Skub derefter forsigtigt panelet ind mod luftrenserens kabinet (2) (g.i).
8 Vask hænderne grundigt efter
montering af ltre.
23DA
Wi-Fi-forbindelse
Opsætning af Wi-Fi­forbindelsen første gang
1 Download og installer appen
"Air Matters" fra App Store eller Google Play.
2 Sæt stikket til luftrenseren i
stikkontakten, og tryk på for at tænde for luftrenseren.
» Wi-Fi-indikatoren blinker
orange den første gang.
3 Kontroller, at din smartphone eller
tablet har oprettet forbindelse til dit Wi-Fi-netværk.
4 Åbn appen "Air Matters", og klik på
"Connect an Air Purier or Monitor" øverst på skærmbilledet. Følg instruktionerne på skærmen for at tilslutte luftrenseren til dit netværk.
5 Efter parring og forbindelse er
oprettet, lyser Wi-Fi-indikatoren hvidt. Hvis parringen ikke lykkes, skal du se afsnittet om fejlnding eller afsnittet Hjælp i appen "Air Matters" for at nde omfattende og opdaterede tip til fejlnding.
Bemærk
Denne vejledning gælder kun, når
luftrenseren opsættes første gang. Hvis netværket er ændret, eller opsætningen skal foretages igen, skal du se afsnittet "Genindstil Wi-Fi­forbindelsen" på side 24.
Hvis du vil slutte mere end én
luftrenser til din smartphone eller tablet, skal du gøre det en ad gangen. Fuldfør opsætningen af én luftrenser, før du tænder den næste luftrenser.
Sørg for, at afstanden mellem din
smartphone/tablet og luftrenseren er mindre end 10 m uden forhindringer.
Denne app understøtter de nyeste
versioner af Android og iOS. Gå til www.philips.com/purier-compatibility for at få de seneste oplysninger om understøttede operativsystemer og enheder.
Genindstil Wi-Fi-forbindelsen
Bemærk
Dette gælder, når standardnetværket,
som luftrenseren er tilsluttet, er ændret.
Nulstil Wi-Fi-forbindelsen, når dit
standardnetværk er ændret.
1 Sæt stikket til luftrenseren i
stikkontakten, og tryk på for at tænde for luftrenseren.
2 Tryk på og samtidigt i
3 sekunder, indtil der lyder et bip.
» Luftrenseren skifter til
parringstilstand.
» Wi-Fi-indikatoren blinker
orange.
3 Følg trin 4-5 i afsnittet "Opsætning
af Wi-Fi-forbindelsen første gang".
24 DA
4 Brug af
Dansk
luftrenseren
Forklaring af luftkvalitetslyset
IAI (Indoor Allergen Index) er en ciervisning i realtid, der giver synlig og øjeblikkelig feedback om allergenniveauet indendørs.
IAI Luftkvali-
tetslysets farve
1-3 4-6
7-9 10-12
Luftkvalitetslyset tænder automatisk, når luftrenseren tændes, og tænder alle farver i rækkefølge. Efter ca. 30 sekunder vælger luftkvalitetssensorerne den farve, som svarer til den omgivende luftkvalitet af luftbårne partikler.
Blå Blå-lilla
Lilla-rød Rød
Sådan tændes og slukkes apparatet
Bemærk
Placer altid luftrenseren på et stabilt,
plant og vandret underlag, så forsiden af enheden vender væk fra vægge eller møbler.
Optimal rensning af luften opnås ved
at lukke døre og vinduer.
Hold gardiner på afstand af luftindtag
eller luftudtag.
Luftkvali­tetsniveau
God Ganske
god Dårlig
Meget dårlig
1 Sæt stikket til luftrenseren i
stikkontakten.
2 Tryk på for at tænde for
luftrenseren (g.j).
» Luftrenseren bipper. » Luftrenseren er som standard i
automatisk tilstand.
» Når luftrenseren opvarmes,
vises " " på skærmen.
» Når luftkvaliteten er blevet
målt i ca. 30 sekunder, vælger luftkvalitetssensoren automatisk den farve, der angiver den målte luftkvalitet.
3 Hold nede i 3 sekunder for at
slukke for luftrenseren.
Bemærk
Hvis luftrenseren stadig er sluttet til
stikkontakten efter slukning, vil den køre under de tidligere indstillinger, når den tændes igen.
Hvis luftrenser slukkes ved et
uheld under driften, genstarter den automatisk og vender tilbage til tidligere indstillinger, når strømmen er kommet igen.
Ændring af blæserhastighed
Der er ere tilgængelige blæserhastigheder. Du kan vælge automatisk tilstand, hastighed 1, 2, 3 eller turbotilstand (t).
Auto (A)
Tryk på blæserhastighedsknappen
gentagne gange for at vælge
automatisk tilstand (g.k).
25DA
Allergentilstand
Den specialdesignede allergentilstand reducerer eektivt almindelige allergener såsom pollen og dyreskæl.
Tryk på blæserhastighedsknappen
for at vælge allergentilstanden
(g.l).
» Auto (A) og vises på
skærmen.
Manuel
Tryk på blæserhastighedsknappen
gentagne gange for at vælge den blæserhastighed, du har brug for (g.m).
Turbo (t)
I turbotilstand kører luftrenseren med den højeste hastighed.
Tryk på blæserhastighedsknappen for at vælge turbotilstanden (t)
(g.n).
Mørkesensortilstand
Du kan aktivere mørkesensortilstanden på to måder.
Manuel aktivering af mørkesensortilstand
Før du lægger dig til at sove, skal du
manuelt trykke på for at aktivere mørkesensortilstanden (g.o).
» Hvis luftkvalitetsindikatoren
lyser blåt, skifter luftrenseren direkte til mørkesensortilstanden. Luftrenseren er støjsvag, og luftkvalitetsindikatorlyset dæmpes.
» Hvis luftkvalitetsindikatoren
ikke lyser blåt, kører luftrenseren i turbo-tilstand i højst 10 minutter. Undervejs blinker luftkvalitetsindikatoren langsomt og skifter derefter til mørkesensortilstanden.
Lyssensor
Lyssensoren gør det muligt for luftrenseren at tilpasse sig til det omgivende lys.
Når det omgivende lys dæmpes i 10 sekunder, slukkes alle lamperne på kontrolpanelet langsomt. I denne periode kan du tænde for alle lamperne igen blot ved at trykke på en vilkårlig knap. Hvis du ikke foretager dig andet inden for 10 sekunder, slukkes alle lamperne.
Når det omgivende lys bliver kraftigere og har varet i mindst 10 sekunder, tændes alle lamperne igen.
26 DA
Automatisk aktivering af mørkesensortilstand
Luftrenseren skifter automatisk til mørkesensortilstanden, hvis lyssensoren registrerer, at lyset i rummet er slukket, mens luftrenseren er i automatisk tilstand eller allergentilstand. Luftrenseren justerer ventilatorhastigheden i realtid for at sikre, at luften i rummet er behagelig. Luftkvalitetslyset dæmpes.
Bemærk
Dansk
Lyssensoren registrerer lyset i rummet
efter 11 timer i mørkesensortilstand.
Hvis lyset i rummet er tændt, afbryder
luftrenseren mørkesensortilstanden og går tilbage til den forrige tilstand. Luftkvalitetslyset og displayet tændes igen.
Tryk på knappen eller for at
forlade mørkesensortilstanden manuelt.
Indstilling af børnesikring 1 Hold børnesikringsknappen
nede i 3 sekunder for at aktivere børnesikringen (g.p).
» Børnesikringsikonet vises på
skærmen.
» Når børnesikringen er
aktiveret, reagerer alle de andre knapper ikke. Det er kun børnesikringsikonet , der blinker.
2 Hold børnesikringsknappen
nede i 3 sekunder for at deaktivere børnesikringen (g.q).
» Børnesikringsikonet
forsvinder.
Bemærk
Børnesikringsfunktionen låses
automatisk op, når koden for rengøring af forlter eller koden for udskiftning af lter vises på skærmen.
5 Rengøring
Bemærk
Sluk altid for luftrenseren, og tag
stikket ud af stikkontakten før rengøring.
Nedsænk aldrig luftrenseren i vand
eller anden væske.
Anvend aldrig slibende, aggressive
eller brændbare rengøringsmidler, f.eks. klor eller sprit, til at rengøre dele af luftrenseren.
Kun forlteret er vaskbart. Luftlteret er
ikke vaskbart.
Forsøg ikke at rengøre ltrene
eller luftkvalitetssensoren med en støvsuger.
Rengøring af luftrenserens kabinet
Rengør regelmæssigt luftrenseren indvendigt og udvendigt, så der ikke samler sig støv.
1 Brug en blød, tør klud til at rengøre
luftrenseren både indvendigt og udvendigt.
2 Luftafgangen kan også rengøres
med en tør, blød klud.
3 Tag frontdækslet af luftrenseren, og
vask det under rindende vand.
27DA
Rengøring af luftkvalitetssensoren
Rengør luftkvalitetssensoren hver 2. måned for at opnå optimal eekt af renseren.
Bemærk
Hvis luftrenseren anvendes i støvede
omgivelser, kan det være nødvendigt at rengøre den oftere.
Hvis luftfugtighedsniveauet i rummet
er meget højt, kan der dannes kondens på luftkvalitetssensoren, og luftkvalitetslyset kan angive en dårligere luftkvalitet, selvom luftkvaliteten faktisk er god. Hvis dette sker, rengøres luftkvalitetssensoren, eller luftrenseren anvendes ved en manuel hastighedsindstilling.
Rengøring af forlteret
Rengør forlteret, når F0 vises på skærmen (g.v).
1 Sluk for luftrenseren, og tag stikket
ud af stikkontakten.
2 Træk den nederste del af
frontpanelet, og løft det derefter forsigtigt for at fjerne det fra luftrenseren (g.c).
3 Tryk klemmen ned (1), og træk
forlteret ind mod dig selv (2) (g.d).
4 Hvis forlteret er meget beskidt,
kan du bruge en blød børste til at fjerne støvet. Vask derefter forlteret under rindende vand (g.w).
5 Lad forlteret lufttørre grundigt,
inden du sætter det tilbage i luftrenseren.
1 Sluk for luftrenseren, og tag stikket
ud af stikkontakten.
2 Rengør luftkvalitetssensorens
indløb og udløb med en blød børste (g.r).
3 Åbn luftkvalitetssensorens dæksel
(g.s).
4 Rengør luftkvalitetssensoren samt
støvindløb og støvudløb med en let fugtet vatpind (g.t).
5 Tør alle dele grundigt med en tør
vatpind.
6 Sæt luftkvalitetssensorens dæksel
på igen (g.u).
Bemærk
Sørg altid for at holde
luftkvalitetssensorens dæksel lukket, når luftrenseren er i drift.
28 DA
Bemærk
For at optimere forlterets levetid skal
du sørge for, at det tørrer helt efter rengøring.
Vask hænder efter at have arbejdet
med lteret.
6 Sæt forlteret tilbage i luftrenseren
(g.h).
Bemærk
Sørg for, at siden med klemmen
peger ind mod dig, og at alle kroge på forlteret er korrekt fastgjort i luftrenseren.
Loading...
+ 160 hidden pages