Philips 55PUD6172/30, 50PUD6172/30 User Manual

Register your product and get support at

www.philips.com/TVsupport

50PUD6172/30

55PUD6172/30

EN User Manual

Contents

1 Notice 2

2 Important 3

3 TV Overview 6

Control Panel 6
Remote Control 6
Use of remote controller 7

4 Using TV 8

Turn on the TV or switch to standby 8
Switch channels 8
To view the connected device(s) 9
Adjust the TV volume 9

5 Using More Feature of your TV 10

Accessing the TV menu 10
Change languages 10
Rename the external devices 10
Reset signal source name 10
Changing the picture settings 10
Change the sound settings 12
Using EPG 13
Use of a timer 13
Channel Editing 14
Updating the TV software 15
Changing TV preferences 15
Watching TV demos 15
Settings when reset to the factory settings
16

6 Media playing 17

Video formats supported by USB 17
Audio formats supported by USB 18
Picture formats supported by USB 19
Viewing photos and playing music and
videos from a connected USB storage
device. 20
Enable the Family entertainments sharing to
view photos and play music and videos 21
Remove the USB storage device 22

7 Installing channels 23

Automatic channel search 23
Manually setting the channel 23
Installing digital channels 23

8 Network setting 24

Turn on/off the smart TV 24
Network type 25
Cable installation 25
Wireless installation 25

9 Connecting Devices 26

Bottom Connectors 26
Side Connectors 27
Using Philips EasyLink 28
Media Center 28
Multi-screen interaction 29

10 Product Information 30

Supported input signal formats 30
Multimedia 30
Tuner / Reception / Transmission 30
Intrinsic Resolution/Sound power 30
Remote Control 30
Power 30
Dimensions and Weights 30
Supported TV Mounts 31

11 Trouble Shooting 32

General TV issues 32
TV channels have problems 32
Picture problem 32
Sound problem 33
HDMI connection problem 33
Computer connection problem 33
Network connection problems 33
Contact Us 33

12 Index 34

Software end user license agreement 34
Disclaimer 37
Open source 37

English

1EN-GB

1 Notice

2019 © TP Vision Europe B.V. All Right Is

Reserved. Specications may be subject to

change without prior notice.All trademarks
are the properties of Koninklijke Philips N.V
or their respective owners. TP Vision Europe
B.V. reserves the right to change products at
any time without the need to give response to
early inventory adjustment.The content in this
manual is suitable for this system.If the intended
use of the product or its individual components

or programs is not within the specied scope

in this manual, you will have to ensure its
effectiveness and applicability.TP Vision Europe
B.V. ensures that the manual itself does not
infringe any patents of the United States.
Disclaimer of Express or Implied WarrantiesTP
Vision Europe B.V. is not responsible for any
errors in the contents of this document, as well
as any problems caused due to the content of
this document.Errors reported to Philips will
be applied and published on the Philips support
website as soon as possible.

Copyright

All other registered and unregistered
trademarks are the property of their respective
owners.
® Kensington and Micro Saver are the
trademarks registered by ACCO World
Corporation in the United States and already
registered and being applied for in other
countries/regions of the world
Part of the copyright of this software belongs to
© The FreeType Project (www.FreeType.org).

HDMI, the HDMI logo and High-Denition

Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio and the
double-D symbol are trademarks of Dolby
Laboratories.

Pixel Characteristics

This LCD product has a high color pixels.
Although it has effective pixels of 99.999% or
higher, the screen may appear black or have
bright spots (red, green, or blue).This is the
structural properties of the display (within the
common industry standards), and is not a fault.

Change components

Users are not allowed to change any
components.Do not open or remove the back
cover of the television and expose its inside.It
must be repaired by Philips service centers and

ofcial repair shops.Otherwise, all declared or

implied warranties will be invalidated.

Any operations specically prohibited in

this manual, any adjustments, or assembly
procedures not recommended nor authorized
in this manual are not within the scope of the
warranty.

2 EN-GB

Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used under licence from Koninklijke
Philips N.V.

2 Important

Before you start using the TV, please read and
understand all instructions. If it is damaged due
to failure to operate in accordance with the
instructions, it is not covered by the warranty.

Safety

Risk of electric shock or re!!

• Do not expose the TV set to rain or water.
Do not place any liquid containers (such as
vases) next to the TV.If liquid is spilled onto
the surface or inside of the TV set, please
power off the TV.Please contact Philips’
customer service center, do not use the TV
set before check.

• Do not put the TV, remote control or

batteries near ame or heat source that

is not isolated, nor directly expose it to
sunlight.

To avoid heat impact, keep the TV, remote
control and batteries away from candles or
other sources of ignition.

• Please do not insert any articles into TV
vents or other openings.

• When the TV set runs, make sure that the
power cord does not become too tight.
If the power cable becomes too tight, the
plug may become loose and experience
arcing.

Risk of short circuit or re!

• Do not expose remote control or batteries
to rain, water or hot environments.

• Please avoid subject the power plug to
external forces. A loose power plug may

cause arcing or re.

Risk of TV damage or destruction!

• TThe TV with a weight greater than 25
kilograms or 55 pounds needs to be handled
by two persons.

• Upon mounting the straight stand on TV,
be sure to use the attached base.Make sure

that the straight stand can rmly support
the TV set.Please place your TV on the at

surface that can support the total weight of
the TV set and the straight stand.

• Upon wall-mounting the TV set, please be
sure to use the bracket that can support
the weight of the TV set. Fix the bracket

rmly on the wall that can support the

total weight of both the TV set and the
bracket. TP Vision Europe B.V. does not
bear any responsibility for accidents,
damage or destruction due to incorrect
wall mounting of the TV set.

• Some parts of this product may contain
glass elements.Please exercise caution
to avoid personal injury or mechanical
damage.

Causing the risk of injury of children!
Please observe the following precautions to
avoid TV fall and child injury:

• Do not place the TV set on the surface
covered by the fabrics or other materials
easy to pull.

• Ensure that TV set does not have any part
of it protruded beyond the edge of the
surface.

• To place the TV set on the top of a tall
item of furniture (bookcases, for example),

please be sure to x the furniture and the

TV set onto the wall or the appropriate
support point.

• Tell your children that climbing onto
furniture to touch the TV set is prone to
danger.

Risk of overheating!

• Do not place the TV set in a narrow space.
The TV must be reserved a space of at least

English

3EN-GB

4 inches or 10 cm around it to ventilate.
Make sure not to allow curtains or other
objects to cover the vents of the TV set.

If inadvertently, the TV set may be damaged!

• Before connecting the TV set to a power
outlet, make sure the outlet voltage is
consistent with the values printed on the
back of the TV set.If both voltage values do
not match, do not connect the TV to the
power outlet.

• The power plug serves as the power
disconnection device and should be easily
operable.

• If your TV needs to be moved into the

storage room for storage, rst remove its

base from the TV set. Do not place the TV

set at against its back when its base is not

removed.

Risk of injury, re or power cord damage!

• Do not put the TV or any objects upon the
power line.

• For easy removal of the TV’s power cord
from the power outlet, a smooth and easy
access to the power cord should always be
kept.

• When pulling out the power cord, be sure
to pull it from its plug part, and never pull
the cable.

• Before the thunderstorm comes, please
cut off the connection between the TV set,
the power outlet and the antenna. During
a thunderstorm, do not touch any part,
power cord or antenna cable of the TV set!

Risk of hearing loss!

• Do not set the headset volume too high
and don’t use the headset for a long time.

Low temperatures

• f the TV set is transported at an ambient
temperature below 5 °C or 41 °F, please
wait for some time after the TV is taken

out of the box until the TV’s temperature
returns to room temperature before it is
connected to the power outlet.

Screen protection

• Please try to avoid rendering xed images
on the screen. A so-called xed image

means an image stays on the screen for a
long time. For example, on-screen menus,
black bars, and time display. If you must use

xed images, please reduce screen contrast

and brightness to avoid screen damage.

• Remove the power cord before cleaning
the TV.

• Use a slightly damp, soft cloth to clean
the TV set and its frame.Do not use
such substances as alcohol, chemicals or
household cleaners to clean the TV set.

• If inadvertently, the TV screen may be
damaged! Do not use items to touch, push,
rub or strike the screen.

• To avoid warping and fading, please wipe
the water droplets as soon as possible.

Note

Static images may cause permanent damage to
the TV screen.

• Do not display static images on the LCD
screen for more than two hours, as this can
cause ghosting.To prevent ghosting, please
reduce the brightness and contrast of the
screen.

• Watching TV in 4:3 format for a long time
may leave different marks on the left and
right edges of the screen and the border of
the image.Avoid using this mode for a long
time.

• Long-term display of static images in videos
and games or computers can cause some
blurring and ghosting due to screen burn.

4 EN-GB

Please correspondingly reduce the screen
brightness and contrast when using the TV

set in this way.
The ghosting, partial ghosting and other traces
displayed on the TV screen for the above
reasons are not within the scope of this
warranty.

Disposal of waste products and
batteries

Your product is designed and manufactured
using high-quality materials and components
that can all be recycled and reused.

When accompanied by an attached cross
recycling bin label, it means that the product
applies to the European Guidelines (European
Directive) 2012/19/EU.
Please obtain the related information about
the local electronic and electrical product

classication and collection systems.

Please dispose it according to local regulations,
and do not discard the waste product together
with other general household wastes.
Correct disposal of waste products helps to
avoid the potential negative impact on human
health and the environment.

English

Your product contains batteries in line with
European standards (European Directive)
2006/66/EC, and shall not be discarded together
with other household waste.
Please pay attention to the local regulations

regarding classication and collection of

batteries, because correct disposal of waste
products can help avoid negative impact on both
the environment and human health.

5EN-GB

3 TV Overview

Remote Control

Congratulations for purchasing and using Philips
product! In order to enjoy all the supports
provided by Philips, please register your TV at
www.philips.com/welcome

Control Panel

5

2

(Product shape may vary according to the
different models, please refer to the actual
models!)

a Open the control menu and serve as a

conrm key between the menu and Smart

TV interface.
b / c Adjust the volume and serve as a

right and left cursors between the menu

and Smart TV interface.
d / e Switch between channels and serve as

a right and left cursors between the menu

and Smart TV interface.

3

1

4

1

2

3

6

9

12

13

17

15

19

23

24

4

5

7

8

10

11

14

18

16

21

20

22

25

6 EN-GB

a (Standby-Power On)

• Start the display, or enter the standby
status.

b Multimedia playback function button

To control play/pause, stop, previous, next
and fast forward, fast rewind.

c

Setting

To open setting option.

d f g button

No function.

e Record button

No function.

h TV

Switch to TV source.

i Smart star

No function.

j EPG

To open EPG menu.

k SMART TV

To enter Smart TV main menu.

l

Color buttons to select corresponding
tasks or options.

m SOURCE(訊號來源)

To open or close the signal source menu,
and select the connected device.

n LIST

To display the channel list.

o

INFO(資訊)

To display the related information about
the signals of the currently played screen.

p OPTIONS（選單）

To display the main screen of the menu.

q OK button

To conrm your input.To press 0~9

number keys and then press OK when
selecting channels.

r

navigation button

Navigation button Select items from the
menu.

s

Volume +/- (音量+/-)

To adjust the volume size.

t

Channel +/-(頻道+/-)

To select the next or previous channel.

u

To return to the previous level/page.

v

Mute
To remain muted.Press the Volume +/­button again, to restore the original volume.

w 0-9 number keys

Press 0~9 number keys to enter a channel.

x Back (返回/輸入)

Press this button to return to the previous
channel.

y Help

To open user manual.

Use of remote controller

When using the remote control, press and hold
it near the TV set, and point it to the remote
control sensor.
Ensure furniture, walls or other objects have not
blocked the sight between the remote control
and the TV set.

5m

30

(Product shape may vary according to the
different models, please refer to the actual
models!)

English

7EN-GB

4 Using TV

This section introduces the basic operations of
the TV.

» If the standby LED indicator is red,

press

(Standby-Power on) on the

remote control.

Switch to standby in the power-on status

• Press the
remote control.

» The standby indicator turns red.

(Standby-Power on) on the

Turn on the TV or switch to
standby

Standby LED indicator

Standby LED Indicator

Turn on the TV

• Plug the power cord into the AC power
outlet.

Tip

•

Although the TV set does not consume much
electricity in standby, but still consumes some;
only unplugging the power plug can this product
be completely powered off.If it is not used for a
long time, unplug the power plug.

Switch channels

Do not use the channel list to
switch channels

• Press Channel Channel +/-(頻道+/-)

on the remote control.

• Enter the channel number using the
number keys on the remote control.

• Press Back (返回/輸入) button on the
remote control to switch back to the
previous channel.

Using the channel list to switch
channels

You can use the channel list to watch all the
channels that can be received.

1 Press OK.

8 EN-GB

» To display the channel list.

2 Press to select channels.
3 Press OK to watch the selected channel.
4 Press to switch to the channel you

watched previously.

To view the connected
device(s)

Note

•

Before selecting the external signal source,
please turn on the external device.

To use the SOURCE(訊號來源) button

Adjust the TV volume

Increase or reduce the volume

• Press
remote control.

Mute or Unmute

• Press
control.

• Press the
control again to restore the sound.

Volume +/- (音量+/-)on the

Mute button on the remote

Mute button on the remote

English

1 Press SOURCES(訊號來源).

» The signal source list appears.

2 Press to select a device.
3 Press OK to select.

» TV is switched to the selected device.

9EN-GB

5 Using More

Feature of
your TV

Accessing the TV menu

The menus can help you set channels, change
picture and sound settings, and set other
features.

1 Press OPTIONS(選單)

» Open the menu.

1 Press , select [Language] > [Menu

languages], then press

.

2 Select the language you want, and then

press OK.

Rename the external devices

After an external device is connected through
the signal source menu, you can rename it
according to your own preferences.

Note

The device can be named using up to 10 Chinese

•

and 10 English characters.

1 Press SOURCES(訊號來源).
2 Select the icon next to the device to be

renamed.

3 Select the relevant icon.
4 Enter the new name.
5 After you have entered the new name,

select [Apply], and then press OK.

2 Select one of the following options, and

press OK:

• [Picture style]: Applies a

predened picture setting options.

• [Sound style]: Applies a predened

sound setting options

• [Channel Info]: Displays the
channel information.

• [Mono/Stereo]: Sets mono or
stereo.

• [Dual I-II ]: Chooses a right
channel.

Note

For different sources, the application menu is

•

different.

Change languages

You can select the language of the menus.

10 EN-GB

Reset signal source name

Reset signal source name.

1 Press SOURCES(訊號來源).
2 Select the icon next to the signal source

to be reset, and then press OK.

3 Select [Reset], and then press OK.

Changing the picture settings

Change the picture settings to suit your

preferences.You can apply the predened

settings or change the settings manually.

Quick picture settings

This feature can help you quickly set pictures

1 Press , select [Picture] > [Quick

Picture and Sound Settings], and then
press OK.

2 Select your favorite setting following the

on-screen instructions.

Picture style

Apply a predened picture setting options by

using the picture style.

1 Press the OPTIONS(選單) and select

[Picture style].

2 Select one of the following settings, and

then press OK:

• [Vivid]: Application of dynamic and
colorful settings, which is suitable for
daytime watching.

• [Natural]: Application of natural
picture quality.

• [Standard]: Adjust the picture
settings to suit most types of video
environments and types.

• [Cinema]: Application of movie-
watching settings.

• [Photo]: Suitable for viewing photos.

• [Energy saving]: Application of the

low power settings.

• [Personal]: Use of custom picture
settings.

Manually adjust the picture
settings

1 Press , select [Picture], and then press

OK.

2 Select one of the following settings, and

then press OK:

• [Quick Picture and Sound
Settings]: To select your favorite

settings following the on-screen
instructions.

• [Picture style]: To select a

predened setting.

• [Contrast]: To adjust the contrast,
to increase the intensity difference
between highlight and dark.

• [Backlight]: To adjust the backlight
intensity.

• [Brightness]: To adjust the intensity

and nesse of dark areas.

• [Color]: To adjust the color
saturation.

• [Sharpness]: To adjust the sharpness
of the image.

• [Soft Blue]: Philips SoftBlue is a
revolutionary technology reducing the
intensity of the harmful spectrum of
the blue light from TV screens. (Note:
To adjust picture mode will cause
SoftBlue automatically set to “Off”.)

• [Tint]: The denition of tint

temperature.

• [Custom tint]: To set your favorite
picture color balance. (This can only
be done when tint temperature is
selected and customized.))

• [4K Pixel Plus]: To ne-tune each

pixel to match surrounding pixels.This
will result in perfect HD images.

• [Advanced sharpness]: To enable

the super-high picture sharpness.

• [Dynamic contrast]: To increase

the contrast with the change of
images.

• [Dynamic backlight]: To

dynamically adjust the brightness of
the backlight on the TV.

• [Color enhancement]: To make

the colors more vivid and richer.

• [Gamma]: To adjust the subtle

shades of pictures.

• [Advanced]:

• [Noise reduction]: To lter and

reduce the noises in an image.

• [PC mode]: To adjust the picture

settings when the computer is
connected to the TV set using
HDMI.

• [Screen edges]: To adjust the

size of the picture to be watched.
(When the maximum value is set,
you may be able to see noises and
uneven edges on the picture. )

• [Picture format]: To change the
picture format.

English

11EN-GB

Changes the picture format

1 Press , select [Picture] > [Picture

format], and then press

Picture format summary

You can congure the following picture settings.

Note

•

Depending on the format of picture sources,
some picture settings are not available.

[Super zoom]:
(This does not apply to
computer mode.)Black edges
caused by removal of the 4:3
format.This action will cause
slight deformation of the
picture.

[4:3]:
Display of the traditional 4:3
picture format.

[Unscaled]:
To adjust the sharpness to
the maximum value.Because
of the television broadcast
system, the picture may have
a very little distortion.Set the
resolution of your computer
to the wide-screen mode for
best display results.

[Subtitle zoom]:

(Not applicable for HD
and PC mode.)Remove the
black border caused by the
4:3 format and make the
subtitles be seen, but the top
part of the picture will be
partially trimmed.

[Movie expand 14:9]:

(Not applicable for HD and
PC mode.)Adjust the picture
format from 4:3 to 14:9.

.

[Movie expand 16:9]:

(This does not apply to
computer mode.)Adjust the
picture format from 4:3 to
16:9.

[Wide screen]:

Adjust the picture format
from 4:3 to 16:9.

[Full screen]:
(Applies only to HDMI
and digital TV signals) This
mode corresponds to the
reproduction rate set to
100%.

Change the sound settings

Change the sound settings to suit your

preferences.You can apply the predened

settings or change the settings manually.

Quick setting of sound settings

This feature helps you quickly set the sound.

1 Press , select [Picture] > [Quick

Picture and Sound Settings], and then
press OK.

2 Select your favorite setting following the

on-screen instructions.

Using Sound Style

To apply a predened sound setting options

using sound style.

1 Press the OPTIONS(選單), select

[Sound Style] , and then press OK.

2 Select one of the following settings, and

then press OK.

• [Standard]: applies to the sound
settings of most environments and
types.

• [News]: Applies to the sound settings
of voice (such as news).

12 EN-GB

• [Cinema]: Applies to the sound
settings of movies.

• [Game]: Applies to the sound
settings of games.

• [Drama]: Applies to the sound
settings of the drama programs.

• [Sports]: Applies to the sound
settings of sports programs.

• [Personal]: To uses the custom sound
settings set in the sound options.

Manual adjustment of sound
settings

Using application menus

Access the options related to the current
activity or selection.

Press the
T V.

•

For different sources, the application menu is
different.

OPTIONS(選單) while watching

» The list of options is divided into

picture style, sound style, channel info,
mono/stereo, dual I-II.

Note

English

1 Press , select [Sound], and then press

OK.

2 Select one of the following settings, and

then press OK.

• [Sound style]: To access the

predened sound settings.

• [Bass]: To adjust bass.

• [Treble]: To adjust treble.

• [Balance]: To adjust the balance of

left and right speakers.

• [Surround]: To turn on or off the
surrounding function.

• [TV position]: To select your TV
mounting mode.

• [Advanced]:

• [Auto volume levelling]: To

automatically reduce sudden
volume changes in switching
channels.

• [Clear sound]: To improve sound

clarity.

• [SPDIF]: To select the audio types

passing the digital audio output
interface (COAXIAL).
[PCM]: To convert the non-PCM
audio types to PCM audio format.
[RAW]: To output audio to home
theater devices.

Using EPG

Program Guide (EPG) is a on-screen guide
provided on the digital channel. Using the EPG,
you can

• View the list of digital programs being
currently broadcasting.

• Watch the incoming programs.

• Set the show reminder.

Starting EPG (Program Guide)

1 Press OPTIONS(選單).
2 Select [EPG], then press OK.

Note

•

It cannot be started directly under non-digital
channels.

Reminders (program guide
feature)

• Press the “Green” key on the program
guide list for reservation or cancel the
programs to be reminded for playwithin a
week.

Use of a timer

You can use a timer in order to switch the TV

to standby at a specied time.

13EN-GB

Using sleep timer

The sleep timer can switch the TV to standby

after a predened time.

Tip

•

You can turn off the TV in advance, and can reset
the sleep timer during the countdown.

1 Press , and select [TV Settings] >

[Sleep timer]

» Display of sleep timer.

2 Select a preset time between 0-180

minutes.

» The sleep timer can be set with the

unit of 10 minutes.If the timer is set to
0, the sleep timer will be shut down.

3 Press OK to start the time timer.

» When the preset time is due, the TV

set will switch to the standby mode.

Channel Editing

You can edit channels.

Use TV lock

You can prevent your children from watching
some programs or channels using TV Lock.

Lock or unlock one or more
channels

1 Press the OK button to open the channel

list.

2 After you select a channel to be locked or

unlocked, press
to lock or unlock the channel.

» If it’s your rst time to watch a locked

channel, you will be asked to enter
your code.

on the remote control

3 After setup, the Lock Channel function will

take effective.

Note

•

When you use the Channel List or the numeric
buttons to select a locked channel, you will be
asked to enter your password.

Chanel Switching

1 Press the OK button to open the Channel

List.

2 Press to select a channel to be

switched. Then press the green key
the remote control, and press the

to select another channel to be switched.

on

key

3 Press the OK button and follow the

instructions to conrm or cancel the

channel switching.

Set or change your password

1 Press , select [Channels] > [Child

lock] > [Set Password].

2 Use the numeric keys on the remote

control to set your password.

» Follow the on-screen instructions to

set or change your password.

Tip

•

If you forget your password, enter “8888” to
overwrite your existing password.

14 EN-GB

Channel Skipping

1 Press the OK button to open the Channel

List.

2 Press to select a channel to be

skipped, and press the yellow key
the remote control to skip it.

on

3 Repeat the steps above to skip more

channels.

Note

Select a skipped channel and press the yellow

•

key on the remote control to cancel
skipping it.

Channel Deletion

1 Press the OK button to open the

Channel List.

2 Press to select a channel to be

deleted, and press the blue key
the remote control to follow the prompt

to conrm or cancel the deletion of the

channel.

on

Updating the TV software

Philips is continuously striving to improve its
products, and we recommend updating your
TV software after updates are launched.

Check the current software
version

1 Press
2 Press the OPTIONS(選單), and

select [About the TV] > [Current
software info], and then press OK.

» Display the current software version

information.

Updating software

You can use the following methods to update
software:

• Connecting the network for automatic
updating.

1 Press .
2 Press the OPTIONS(選單), and

select [About the TV] > [Current
software info], and then press OK.

3 Update the software following the on-

screen instructions.

• Using USB storage devices for automatic
updating.

1 Press .
2 Press the OPTIONS(選單), and

select [About the TV] > [Manual
software updates], and then press OK.

3 Update the software following the on-

screen instructions.

Note

•

Your USB memory stick should be removed
after software update.

• For software update, please use the USB device.

The hard disk may cause the update to fail and
restart because of the excessive demand for the
current.

Changing TV preferences
1

Press , and select [TV Settings].

2 Select one of the following items, and

then press OK.

• [Location]: To select the position of
your TV set.

• [Picture and Sound reset]: To
restore all the TV picture and sound
settings to their default values.

• [EasyLink]: To set the EasyLink-
related features.

• [HDMI Ultra HD]: HDMI interface
for the HDMI switch can support the
EDID format project, to strengthen
the compatibility with equipment.

• [About the TV]: To display the
information about TV.

• [Key Beep]: To turn on the button
sound of the remote control.When
the user presses the remote control
button, the TV will give a sound.

• [Sleep timer]: To let the TV set to
go into sleep after the set time.

• [Clear Cache]: To clear the cache
data from the built-in SD card
partitioning.

• [Reinstall TV]: Restore all of the
TV settings to their default values.

Watching TV demos

You can better understand the functions of TV
from the TV demos. Some models do not have
this function.

1 Press .

English

15EN-GB

2 Select [TV Settings] > [Location] >

[Shop], and then press OK to watch.

Settings when reset to the
factory settings

You can reset the picture and sound settings to
the factory settings. Channel settings will not
be reset.

1 Press , and select [TV Settings] >

[Picture and Sound reset], and then
press OK.

2 Select [OK], to start resetting the settings.

16 EN-GB

6 Media playing

Video formats supported by
USB

File formats Video formats Maximum code

rate
AVI
(.avi)

MPEG-2
TS
Transport
Stream
(.ts)

MPEG
FileFormat
(.mpeg)

MPEG-4
Part 14
(.mp4)

MPEG-1, 80Mbps
MPEG-2
MP@HL,
MPEG-4 SP@
L0-3,ASP @
L0-5,
H.264
MP,HP@Level

4.1,
VC1 (AP), 45Mbps
H263, 5Mbps
MJPEG,
MPEG-2
MP@HL,
MPEG-4 SP@
L0-3,ASP @
L0-5,
H.264
MP,HP@Level

4.1,
AVS baseline @
level 6.0,
VC1 (AP), 45Mbps
H265 100Mbps
MPEG-1, 80Mbps
MPEG-2
MP@HL,
H.264
MP,HP@Level

4.1,
H.264
MP,HP@Level

4.1,
MPEG-4 SP@
L0-3,ASP @
L0-5,
H265 100Mbps

80Mbps

50Mbps

100Mbps(VCL)

120Mbps(NAL)

80Mbps

50Mbps

100Mbps(VCL)

120Mbps(NAL)

50Mbps

80Mbps

100Mbps(VCL)

120Mbps(NAL)

100Mbps(VCL)

120Mbps(NAL)

50Mbps

QuickTime
(.mov)

BDAV
MPEG-2
transport
stream
(.m2ts)

Matroska
(.mkv)

Flash Video

(.v)

Video
OBject
(.vob)
DAT
(.dat)
Advanced
Stream
Format
(.asf)

3gp H.264

tp MPEG-2

H.264
M P,
HP@
Level

4.1,
MPEG-4 SP@
L0-3
ASP @L0-5,
MJPEG,

H265 100Mbps
H.264
MP,HP@Level

4.1,
VC1 (AP), 45Mbps
MPEG-2
MP@HL,
H.264
MP,HP@Level

4.1,
VC1 (AP), 45Mbps
H265 100Mbps
H.264
MP,HP@Level

4.1,
H263, 5Mbps
MPEG-2
MP@HL,

MPEG-1, 80Mbps

VC1 (AP), 45Mbps
H.264
MP,HP@Level

4.1,
MPEG-4 SP@
L0-3,ASP @
L0-5,

MP,HP@Level

4.1,
H263, 5Mbps
MPEG-4 SP@
L0-3,ASP @
L0-5,

MP@HL,

100Mbps
(VCL)
120Mbps
(NAL)

50Mbps

100Mbps(VCL)
120Mbps(NAL)

80Mbps

100Mbps(VCL)
120Mbps(NAL)

100Mbps(VCL)
120Mbps(NAL)

80Mbps

100Mbps(VCL)
120Mbps(NAL)

50Mbps

100Mbps(VCL)
120Mbps(NAL)

50Mbps

80Mbps

English

17EN-GB

trp H.264

MP,HP@Level

4.1,
MPEG-2
MP@HL,

File formats Frame

rate
AVI
(.avi)

MPEG-2
TS
Transport
Stream
(.ts)

MPEG File
Format
(.mpeg)

MPEG-4
Part 14
(.mp4)
QuickTime
(.mov)

BDAV
MPEG-2
transport
stream
(.m2ts)

30FPS 1920x1080 MPEG-1

30FPS 1920x1080

30FPS 1920x1080

30FPS 3840x2160

30FPS 1920x1080

30FPS 1280x720

30FPS 1920x1080

30FPS 1920x1080 MP3

30FPS 1920x1080

30FPS 3840x2160

30FPS 1920x1080

30FPS 1920x1080

30FPS 3840x2160

30FPS 1920x1080 PCM,

30FPS 1920x1080

30FPS 3840x2160

30FPS 3840x2160 AAC

30FPS 1920x1080

30FPS 3840x2160

30FPS 3840x2160 AAC

30FPS 1920x1080

30FPS 1920x1080

30FPS 3840x2160

30FPS 3840x2160

30FPS 1920x1080

30FPS 1920x1080

100Mbps(VCL)
120Mbps(NAL)

80Mbps

Resolution Audio

formats

Layers I, II,
III(MP3)
AAC,
AC3,
PCM,
WMA,
WMAPro

AAC
AC3
PCM

AC3,
MP3

Matroska
(.mkv)

Flash Video

(.v)

Video
OBject
(.vob)
DAT
(.dat)
Advanced
Stream
Format
(.asf)

3gp 30FPS 3840x2160 AMR_NB,

tp 30FPS 1920x1080 MPEG-1

trp 30FPS 3840x2160 MP3

30FPS 3840x2160 AAC,

30FPS 1920x1080

30FPS 3840x2160

30FPS 3840x2160 AAC,

30FPS 1280x720

30FPS 1920x1080 AC3

30FPS 1920x1080 PCM

30FPS 1920x1080 mp3,

30FPS 3840x2160

30FPS 1920x1080

30FPS 1280x720

30FPS 1920x1080

30FPS 1920x1080

AC3,
MP3

MP3

PCM
MP3

MP3

PCM
WMA

AAC

Layers II,
AC3

Audio formats supported by
USB

Audio les Audio

formats
Windows
Media
Audio
(.wma)
MPEG
Audio
Layer III
(.mp3)
Advanced
Audio
Coding
(.aac)

WMA

WMAPro

MPEG 32kHz~

AAC 16kHz~

Sample rate Code rate

8KHz ~

48Khz

48kHz

48kHz

128bps ~

320Kbps

32kbps ~

320kbps

24kbps ~

384kbps

18 EN-GB

N/A(Work
with video

les only)

AC3 32kHz,

44.1kHz,
48kHz

EAC3 32kHz,

44.1kHz,

32kbps ~

640kbps

32Kbps ~

6 Mbps

48kHz
OGG Vobis
(.ogg)

Vorbis 8kHz~

48kHz

max
320Kbps

Picture formats supported by
USB

Format Maximum resolution Minimum

resolution

png

jpeg

bmp

8K×8K(hard parse) 4×4

Baseline 8K×8K, (hard

4×4
parse), progressive
progressive 4K×4K
8K×8K 4×4

Note

If the content, packaging, or coding does not

•

meet the standards, the video content may not
play correctly. The failure to play due to some

specic parameters of the sources that go

beyond the decoding range is not a fault of the
machine.

• The animated GIF pictures are not supported.

• Before connecting the device to the TV set,

please back up your les to prevent le damage

or data loss.For no support for USB storage
devices, Philips assumes no responsibility, and
shall not be liable for any damage or loss of data
in the device.

• Some high-power USB devices might not be

supported.(more than 0.5A).

• When connecting or using a USB device, if there

is a power overload warning message, you may
not be able to identify the device or the device
may have problems.

English

19EN-GB

Viewing photos and playing
music and videos from a
connected USB storage device.

Turn on the TV.

1
2 Connect the USB storage device to the

USB slot on the side of TV set.

3 Press SOURCES(訊號來源).
4 Select [USB], and then press OK.
5 If there is more than one USB storage

device, select the USB storage device to be
read, and press OK.

» The browse page opens.

Change the slide show settings

1 Press OPTIONS(選單) when playing a

slide.

» Display the list of slide show options,

and browse photos in accordance with
the instructions on the screen.

Note

•

The information about the photos will only
appear when the slide stops playing.

Listen to music

View photos

1 Select [Folders] or [Photo] in the

browse page, then press OK.

2 Select a photo and press OK.

» Enlarge the picture to the full screen

size.

Start/Pause the slide
show

(Navigation

button)

View the previous/next
picture

Return to the browse
page

1 Select [Folders] or [Music] in the

browse page, and then press OK to play.

» Change the settings for playing music

according to the instructions on the
screen.

Start / Pause the music

Fast rewind/fast
forward

Previous/Next track

Return to the browse
page

Please read the option
instructions

20 EN-GB

Please read the option
instructions

Playing music while viewing slides

You can play background music while viewing
slides.

1 Select a music album.
2 Press OK.
3 Press to return to the main screen of

the browse page.

4 Select a picture.
5 Press OK to play the slide.

Watch the movie

1 Select [Folders] or [Video] in the

browse page.

2 Press OK to play the movie.

» Change the settings for playing the

movie according to the instructions on
the screen.

Enable the Family
entertainments sharing to view
photos and play music and
videos

1

Turn on the TV.

2 Connect the TV to the Internet or the

wireless network.

3 Start up the multimedia devices that

support the Family entertainments sharing.

» The multimedia devices for Family

entertainments sharing will share

multimedia les with the TV through

networks.

4 Press SOURCES(訊號來源).
5 Select [Family entertainments

sharing], and then press OK.

» The browse page opens.

English

Start / Pause the video.

Fast rewind/fast
forward

Previous/Next movie

Return to the browse
page

Please read the option
instructions

View photos

1 Select Picture in the browse page, then

press OK.

2 Select a photo and press OK.

21EN-GB

Return to the browse page

Return to the browse page

Listen to music

1 Select Music in the browse page, and then

press OK to play.

» Change the settings for playing music

according to the instructions on the
screen.

Return to the browse page

Watch the movie

1 Select video in the browse page.
2 Press OK to play the movie.

Remove the USB storage
device

Note

•

Please follow the following steps to remove the
USB storage device to prevent damage.

1 Press to return or leave the main screen

of the browse page.

2 Wait about ve seconds, and then remove

the USB storage device.

22 EN-GB

7 Installing

Step 2 Search and store new
channels

channels

The rst time you set up your TV, you are

prompted to select a menu language and
to install TV channels. This section provides

instructions on how to re-install and ne-tune

channels.

Automatic channel search
1

Press .

2 Select [Channels] > [Channel settings]

and press OK

3 Press OK to start the automatic channel

search.

Note

•

This feature can be used only in the TV mode.

Manually setting the channel

Step 1 Select your system

1 Press .
2 Select [Channels] > [Analog channel

manual installation].

3 Select your [Color system] and [Sound

system].

1 Press .
2 Select [Channels] > [Analog channel

manual installation] > [Find
channel].

• Channel frequency can be entered
directly.

• Select [Search], and press OK to
start the search.

3 Search, and select [Cancel] to leave the

menu.

4 When the search is complete, select

[Save] and leave the menu.

• Saving the searched channels

Step 3 Fine-tune the analogue
channels

1 Press .
2 Select [Channels] > [Analog channel

manual installation] > [Fine tune].

3 Press [Decrease] or [Increase] to

adjust the channel frequency.

Installing digital channels
1

Press .

2 Select [Channels] > [Digital channel

manual installation] and press OK.

3 Enter the channel frequency directly.
4 Select [Search], and press OK to start

the search.

English

Note

•

If your system settings are correct, you can skip
this step.

23EN-GB

8 Network

setting

Turn on/off the smart TV

You can set up a network in order to access
different networks.

1 Connect the TV to the Internet.If there is

no network connection, some features of
the smart TV will not work properly.

2 Press the button on the remote control.

» The picture jumps automatically to the

smart TV.

(The pictures and the applications in pictures
are for reference only. The actual machine
should prevail!)

Display and control the applications which had
been installed in this TV..

Games

Download hot games from the Game App store
partners.

Note

Part of the applications only supports operation

•

by mouse.

• Memory space does not mean the usable space.

• Philips reserves the right to increase and

decrease the right of part of the applications.

• Do not arbitrarily change the ROM of the TV,

and any resulting failure is not covered under
warranty.

Application

Download hot applications from the App store
partners.

24 EN-GB

Network type

You can select the type of network settings.

1 Press , and select [Connection]>

[Wired or Wireless].

2 In the [Smart TV] mode, press the

OPTIONS(選單) > [Connect to
network].

» If you need to know the MAC address,

press the
[View network settings] item for

view in the smart TV mode.

OPTIONS(選單) >

Cable installation

To connect the TV to computer networks
and Internet, you need to install a router in
computer networks. Connect your router to the
TV set using a network cable (Ethernet cable).

Connect the router to the network interface
at the bottom of the TV set using a network
cable, and turn on the router before you begin
network installation.

Wired network settings ­automatic search

5 And press OK again.

» Display of on-screen keypad.

6 Use the on-screen keypad to enter the [IP

address], [Subnet mask], [Gateway]
and [DNS1] .

7 After you have entered, select [OK], then

press OK.

Wireless installation

1

Press .

2 Selesct [Connection] > [Wired or

Wireless] > [Connect to network] >
[Wireless network] .

3 Select [On].

» The screen will display the currently set

network parameters, and the wireless
network that can be connected.

English

1 Press .
2 Select [Connection] > [Wired or

Wireless] > [Connect to network] >
[Wired network].

3 Select [DHCP] , then press OK.

» Network protocols will be set

automatically.

Wired network settings - Manual
input

1 Press .
2 Select [Connection] > [Wired or

Wireless] > [Connect to network] >
[Wired network].

3 Selec [Static IP], then press OK.
4 Press , position the cursor in the input

box.

25EN-GB

9 Connecting

Devices

This section describes how to connect devices
with different connectors.

Note

•

You can use different types of connectors to
connect a device to your TV.

Bottom Connectors

a AV input (left/right video, audio)

• Video: Composite video inputs in the
analog devices such as VCR.

• Audio: Audio inputs in the analog
devices connected to the video.

R-AUDIO-L VIDEO

c Coaxial output

Digital audio output to home theater
systems and other digital audio systems.

COAXIAL

d HDMI 2 /HDMI 3

Digital audio and video input in Blu-ray disc
player and other HD digital devices.

b Connecting the network

Network port

• Data input from the network.

26 EN-GB

Note

•

Supported resolution:
HDMI 2/ HDMI 3: FHD, UHD

e Connecting computers

Before you connect your computer to your
T V.

• Set the refresh rate to 60Hz on the
computer’s screen.

• Select a supported screen resolution
on your computer.

Connecting to your computer through one
of the following interfaces:

• HDMI cable

English

Side Connectors

a Antenna/cable TV

Signal input from an antenna or cable.

ANTENNA

b USB 1 / USB2

Data input into USB storage devices.

Note

•

Supported resolution:
HDMI 1: FHD,UHD

c HDMI 1

Digital audio and video input in Blu-ray disc
player and other HD digital devices.

27EN-GB

Using Philips EasyLink

Taking full advantage of your Philips EasyLink
HDMI-CEC compatible devices can enhance
the control function and achieve the best
possible results.HDMI-CEC compatible devices
connected through the HDMI connector can be
controlled by a TV remote control.
To enable Philips EasyLink, you need to:

• Make sure that each HDMI-CEC compatible
device can run normally.

• Switch to EasyLink

Note

•

EasyLink-compatible device must already be
turned on and is selected as a signal source.

• Philips does not guarantee its 100%

interoperability with all HDMI CEC devices.

Turn on or off EasyLink

Note

•

Pease do not enable Philips EasyLink if you do
not intend to use it.

1 Press .
2 Select [TV Settings] > [EasyLink]>

[EasyLink].

3 Select [Off] or [On] and press OK.

Turn on or off the EasyLink
remote control

Note

•

Pease do not enable Philips EasyLink if you do
not intend to use it.

1 Press .
2 Select [TV Settings] > [EasyLink]>

[EasyLink remote control].

3 Select [Off] or [On] and press OK.

Using the quick standby

1 Press (standby-power on) on the

remote control.

» The TV and all connected HDMI

devices will be switched to standby.

Conguring the TV speakers

1 Press .
2 Select [TV Settings] > [EasyLink] >

[TV Speakers].

3 Select one of the following items, and then

press OK.

• [Off]: Turn off the TV speakers.

• [On]: Turn on the TV speakers.

• [EasyLink autostart]: To

automatically disable the TV speakers,
and transmit the TV audio to the
connected HDMI-CEC audio device.

Media Center

You can browse the pictures, videos or music

and other multimedia les in the USB devices or

local media.

Choose pictures, video or music les from the

home page, and then press the OK button to

conrm.

For the operating instructions, refer to [View
photos and play music and movies from a
connected USB storage device] or [Enable
the Family entertainments sharing to view
photos and play music and videos]

Note

•

Supported storage devices: Make sure that the
USB is connected.

28 EN-GB

Multi-screen interaction

You can use a mobile device, such as a Philips
W8510, to display the content (the contents to
be displayed depends upon the mobile device)
on the screen of the mobile device on the TV
screen through multi-screen interaction, and
support playback of the sound content
transmitted by synchronization from the mobile
device.

During the transmission, the
音量+/-) buttons on the remote control can be

used to control the volume of sound.

Note

•

Multi-screen interaction feature cannot be
compatible with all mobile phone devices.

Volume +/- (

Establishing a connection

1 Press .
2 Select [Connectiont] > [Wired or

Wireless] > [Screen sharing] > [On].

3 Use WLAN/Wireless display on a mobile

device, to send a connection request >
Connection successful, and the pictures on
a mobile device are transmitted to the TV
screen.

English

Way of disconnection

1 In transmission, the mobile device is

disconnected.

2 In transmission, press the Return

button on the remote control, etc. can
disconnect.

Note

Only when the wireless functions of the TV and

•

the mobile device is turned on can the multi­screen interaction function can be used.

29EN-GB

10 Product Infor-

mation

Product information may be subject to change
without prior notice.For detailed product
information, please go to www.philips.com/
TVsupport

Supported input signal formats

Computer Formats

• Resolution - refresh rate:

• 640 × 480 - 60Hz

• 800 × 600 - 60Hz

• 1024 × 768 - 60Hz

• 1360 × 768 - 60Hz

• 1920 × 1080 - 60Hz

Video Formats

• Resolution - refresh rate:

• 480i - 60Hz

• 480p - 60Hz

• 576i - 50Hz

• 576p - 50Hz

• 720p - 50Hz, 60Hz

• 1080i - 50Hz, 60Hz

• 1080p- 24Hz, 25Hz, 30Hz, 50Hz, 60Hz.

• 4K × 2K - 30Hz, 23.98Hz, 25Hz,

50Hz/60Hz

Tuner / Reception / Transmission

• Aerial input: 75 ohm coaxial (IEC75)

• TV system: PAL D/K, DTMB

• Video playback: NTSC, PAL

• Tuner bands: UHF, VHF

Intrinsic Resolution/Sound
power

• Intrinsic Resolution

• 50PUD6172/30: 3840 x 2160

• 55PUD6172/30: 3840 x 2160

• Sound power

• 50PUD6172/30: 8W x 2

• 55PUD6172/30: 8W x 2

Remote Control

• Battery: 2 × AAA

Power

• Mains: 220 V , 50 Hz

• Standby power consumption: ≤ 0.5 W

• Ambient temperature: 5-45 °C

• Power consumption:

• 50PUD6172/30: 130W

• 55PUD6172/30: 150W

Note

When the TV set does not support resolution

•

and refresh rate, there will be a black screen or

ower screen. Please switch to the TV set to

display resolution and refresh rate.

Multimedia

• Supported storage device: USB Supports
FAT 32/FAT 16 USB storage devices.)

30 EN-GB

Dimensions and Weights

50PUD6172/30

• Without TV stand (W) × (H) × (D):

1127.54mm × 666.63mm × 85.9mm

- Weight: 11.1kg

• With TV stand (W) × (H) × (D)

1127.54mm × 716.91mm × 262.47mm

- Weight: 11.46kg

55PUD6172/30

• Without TV stand (W) × (H) × (D):
1241mm × 730.36mm × 87.72mm

- Weight: 13.4kg

• With TV stand (W) × (H) × (D)
1241mm × 781.91mm × 262.74mm

- Weight: 13.6kg

Supported TV Mounts

To install the TV set, purchase a Philips TV
mounting bracket.

Warning

Please follow all the instructions provided with

•

the TV mounting bracket. TP Vision Europe
B.V. does not bear any responsibility for any
accidents, personal injury or loss caused by
improper TV mounting.

1 Please rst lock the mount behind the TV.
2 To prevent damage to cables and

connectors, be sure to leave a clearance of
at least 2.2 inches or 5.5cm from the back
of the locked TV (including the protruding
parts of the speakers) to the wall.

3 Make sure that your mounting bolts follow

these specications:

English

TV screen
size(inch)

50 200 × 200

55 200 × 200

Required
dot pitch
(mm)

Required mounting
screws

4 x M6
(We recommend an
effective thread length
of 14MM (without
gaskets), and the
maximum thread
length of 16MM
(without gaskets))

4 x M6
(We recommend an
effective thread length
of 14MM (without
gaskets), and the
maximum thread
length of 16MM
(without gaskets))

31EN-GB

11 Trouble Shoot-

ing

This section describes the commonly
encountered issues and accompanying solutions.

General TV issues

TV set cannot be started:

• Disconnect the power cord plug from the
power outlet. Reconnect it one minute later.

• Check that the power cord is rmly
connected.

The remote control does not function normally:

• Check that the +/- poles of the remote
control battery are installed properly.

• If the remote control batteries are
exhausted or leak, please replace it.

• Clean the remote control and TV sensor
lens.

The TV standby light is blinking in red:

• Disconnect the power cord plug from the
power outlet. Wait until the TV set cools
down and then reconnect the cable. If the

ashing still occurs, please contact the

Philips customer service center.

Forget the code to unlock the TV lock:

• Input ‘8888’.

The TV menu’s display language is wrong:

• Change the TV menu to the desired
language.

Hear a squeak in the TV box after turning on/off
the TV to standby state:

• You need not perform any action. Squeaking
is a normal sound given from normal
dilatation of the TV set during cooling and
warming. This will not affect performance.

TV channels have problems

The previous channel installed does not appear
in the channel list:

• Check that the selected channel list is
correct.

Picture problem

The TV is on, but has no picture:

• Check that the antenna is not properly
connected to the TV.

• Check that a correct device is selected as
the TV signal source.

There is no sound nor picture:

• Check that the picture settings are correct.

Antenna connection causes bad reception of the
TV set:

• Check that the antenna is not properly
connected to the TV.

• Loudspeakers, unearthed audio devices,
neon lights, high buildings and other large
objects can affect the reception quality.
If possible, try improving the reception
quality by changing the antenna direction
or keeping the above device away from the
TV set.

• If there is only one channel having poor
reception, please ne tune this channel.

Poor picture quality of the device connected
thereto:

• Check the connection of the device.

• Check that the picture settings are correct.

The TV set has no settings for saving pictures:

• Check the TV location is set to home
settings. This mode gives you the exibility
to change and save settings.

The picture does not t on the screen, too large

or small:

• Try using a different picture format.

The picture position is not correct:

• The picture signal in some devices may not

t the screen correctly.Check the signal

output of the device.

32 EN-GB

Sound problem

There is a picture but the sound quality is poor:

Note

If audio signal cannot be detected, the TV set will

•

automatically switch off audio output - This does
not indicate a failure.

• Check that all cables are properly
connected.

• Check that the volume is not set to 0.

• Check the sound is not muted.

There is picture, but the sound quality is poor:

• Check that the sound settings are set
properly.

There is a picture, but only one speaker has
sound:

• Check that the sound balance is set to the
middle.

HDMI connection problem

HDMI has a problem:

• Note that HDCP (high-bandwidth digital
content protection) support may delay TV
display of the time of the contents in the
HDMI device.

• If the TV cannot recognize the HDMI
device, and does not display, please attempt
to switch the signal source from a device to
another and switch back again.

• If the sound is on and off, please check
the output of the HDMI device is set up
correctly.

Network connection problems

Web surng is not working properly:

• If the connection to the router is set up
correctly, please verify that the router is
properly connected to the Internet.

Browsing speed or Web surng speed is slow:

• Please refer to your router’s user manual
to learn about the information such as
transmission rates and other factors of
signal quality.

• You need to apply to the router’s high-
speed Internet connection.

Contact Us

If you cannot resolve the problem, please refer
to the frequently asked questions about the TV
set in the following Web site:
www.philips.com/TVsupport.
If the problem is still not resolved, please contact
your local Philips customer service center.

Warning

Do not attempt to repair the TV on your own.

•

This may cause serious personal injury, and
cause irreparable damage to the TV set or void
the warranty.

Note

Before you contact Philips customer service

•

center, please record your TV models and serial
numbers.The numbers are printed on the back
and packaging of the TV set.

English

Computer connection problem

The computer display is unstable on the TV:

• Check that your PC uses a supported
resolution and refresh rate.

• Set the TV picture format to no
compression.

33EN-GB

12 Index

Software end user license
agreement

THIS SOFTWARE END USER LICENSE
AGREEMENT (“THIS AGREEMENT”) IS
A LEGAL AND BINDING AGREEMENT
BETWEEN YOU (EITHER AN INDIVIDUAL
OR ENTITY) AND TP VISION EUROPE B.V.,
A LIMITED LIABILITY COMPANY LOCATED
AT PRINS BERNHARDPLEIN 200, 1097 JB,
AMSTERDAM, THE NETHERLANDS, AND
ITS AFFILIATED COMPANIES (TOGETHER
REFERRED TO AS “TP VISION”). THIS
AGREEMENT GIVES YOU THE RIGHT TO USE
CERTAIN SOFTWARE (THE “SOFTWARE”)
INCLUDING USER DOCUMENTATION IN
ELECTRONIC FORM WHICH MAY HAVE
BEEN PROVIDED SEPARATELY OR TOGETHER
WITH A TP VISION PRODUCT (THE
“DEVICE”) OR A PC. BY DOWNLOADING,
INSTALLING OR OTHERWISE USING THE
SOFTWARE, YOU ACCEPT AND AGREE
TO BE BOUND BY ALL OF THE TERMS
AND CONDITIONS OF THIS AGREEMENT.
IF YOU DO NOT AGREE TO THESE
TERMS AND CONDITIONS, DO NOT
DOWNLOAD, INSTALL OR OTHERWISE USE
THE SOFTWARE. IF YOU ACQUIRED THE
SOFTWARE IN TANGIBLE MEDIA E.G. CD
WITHOUT THE OPPORTUNITY TO REVIEW
THIS LICENSE AND DO NOT ACCEPT THESE
TERMS, YOU MAY RECEIVE A FULL REFUND
OF THE AMOUNT, IF ANY, THAT YOU PAID
FOR THE SOFTWARE IF YOU RETURN THE
SOFTWARE UNUSED WITH PROOF OF
PAYMENT WITHIN 30 DAYS FROM THE DATE
OF PURCHASE.

solely for your personal use. The Software is “in
use” when it is loaded into the temporary or
permanent memory (i.e. RAM, hard disk, etc.) of
the PC or the Device.

2. Ownership. The Software is licensed and not
sold to you. This Agreement grants you only the
right to use the Software, but you do not acquire
any rights, express or implied, in the Software

other than those specied in this Agreement.

TP VISION and its licensors retain all right, title,
and interest in and to the Software, including
all patents, copyrights, trade secrets, and other
intellectual property rights incorporated
therein. The Software is protected by copyright
laws, international treaty provisions, and other
intellectual property laws. Therefore, other than
as expressly set forth herein, you may not copy
the Software without prior written authorization
of TP VISION, except that you may make one (1)
copy of the Software for your back-up purposes
only. You may not copy any printed materials
accompanying the Software, nor print more
than one (1) copy of any user documentation
provided in electronic form, except that you may
make one (1) copy of such printed materials for
your back-up purposes only.

3. License Restrictions. Except as provided
otherwise herein, you shall not rent, lease,
sublicense, sell, assign, loan, or otherwise transfer
the Software. You shall not, and you shall not
permit any third party, to reverse engineer,
decompile, or disassemble the Software, except
to the extent that applicable law expressly
prohibits the foregoing restriction. You may not

remove or destroy any product identication,

copyright notices, or other proprietary markings
or restrictions from the Software. All titles,
trademarks, and copyright and restricted rights
notices shall be reproduced on your back up
copy of the Software. You may not modify or
adapt the Software, merge the Software into
another program or create derivative works
based upon the Software.

1. Grant of License. This Agreement grants
you a non-exclusive, nontransferable, non-sub
licensable license to install and use, on the
Device or a PC, as applicable, one (1) copy of the

specied version of the Software in object code

format as set out in the user documentation

34 EN-GB

4. Termination of certain functionality. The
Software may contain components of certain
licensed software including software licensed
from Microsoft Corporation (“Microsoft”)
which implements Microsoft’s digital rights
management technology for Windows Media.

Content providers are using the digital rights
management technology for Windows Media
(“WM-DRM”) to protect the integrity of their
content (“Secure Content”) so that their
intellectual property, including copyright, in such
content is not misappropriated. Your Device
may also use WM-DRM software to transfer or
play Secure Content (“WM-DRM Software”).
If the security of such WM-DRM Software is
compromised, Microsoft may revoke (either on
its own or upon the request of the owners of
Secure Content (“Secure Content Owners”))
the WM-DRM Software’s right to acquire new
licenses to copy, store, transfer, display and/
or play Secure Content. Revocation does not
alter the WM-DRM Software’s ability to play
unprotected content. A list of revoked WM­DRM Software is sent to your PC and/or your
Device whenever you download a license for
Secure Content. Microsoft may, in conjunction
with such license, also download revocation lists
onto your Device on behalf of Secure Content
Owners, which may disable your Device’s ability
to copy, store, display, transfer, and/or play Secure
Content. Secure Content Owners may also
require you to upgrade some of the WM-DRM
components distributed with this Software
(“WM-DRM Upgrades”) before accessing their
content. When you attempt to play Secure
Content, WM-DRM Software built by Microsoft
will notify you that a WM-DRM Upgrade is
required and then ask for your consent before
the WM-DRM Upgrade is downloaded. WM­DRM Software built by TP VISION may do the
same. If you decline the upgrade, you will not
be able to access Secure Content that requires
the WM-DRM Upgrade; however, you will still be
able to access unprotected content and Secure
Content that does not require the upgrade.
WM-DRM features that access the Internet, such
as acquiring new licenses and/or performing a
required WM-DRM Upgrade, can be switched
off. When these features are switched off, you
will still be able to play Secure Content if you
have a valid license for such content already
stored on your Device. However, you will not
be able to use certain of the WM-DRM Software
features that require Internet access such as the
ability to download content that requires the
WM-DRM Upgrade. All title and intellectual
property rights in and to the Secure Content is
the property of the respective Secure Content

owners and may be protected by applicable
copyright or other intellectual property laws and
treaties. This Agreement grants you no rights
to use such Secure Content. To summarize,
if the Software contains Microsoft WM-DRM
components – Secure Content you desire to
download, copy, store, display, transfer, and/
or play is protected by the Microsoft WM­DRM components of the Software. Microsoft,
Secure Content Owners, or Secure Content
distributors may deny you access, or restrict
your access, to Secure Content even after you
have paid for, and/or obtained, it. Neither your
consent nor the consent or approval of TP
VISION is necessary for any of them to deny,
withhold or otherwise restrict your access to
Secure Content. TP VISION does not guaranty
that you will be able to download, copy, store,
display, transfer, and/or play Secure Content.

5. Open Source Software. (a) This software may
contain components that are subject to open­source terms, as stated in the documentation
accompanying the Device. This Agreement does
not apply to this software as such. (b) Your
license rights under this Agreement do not
include any right or license to use, distribute
or create derivative works of the Software in
any manner that would subject the Software
to Open Source Terms. “Open Source Terms”
means the terms of any license that directly
or indirectly (1) create, or purport to create,
obligations for TP VISION with respect to the
Software and/or derivative works thereof; or
(2) grant, or purport to grant, to any third party
any rights or immunities under intellectual
property or proprietary rights in the Software
or derivative works thereof.

6. Termination. This Agreement shall be effective

upon installation or rst use of the Software and

shall terminate (i) at the discretion of TP VISION,
due to your failure to comply with any term of
this Agreement; or (ii) upon destruction of all
copies of the Software and related materials
provided to you by TP VISION hereunder. TP
VISION’s rights and your obligations shall
survive the termination of this Agreement.

7. Upgrades. TP VISION may, at its sole option,
make upgrades to the Software available by
general posting on a website or by any other

English

35EN-GB

means or methods. Such upgrades may be
made available pursuant to the terms of this
Agreement or the release of such upgrades
to you may be subject to your acceptance of
another agreement.

8. Support Services. TP VISION is not obligated
to provide technical or other support (“Support
Services”) for the Software. If TP VISION does
provide you with Support Services, these will
be governed by separate terms to be agreed
between you and TP VISION.

OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, AND ACCURACY
OR COMPLETENESS OF RESULTS WITH
RESPECT TO THE SOFTWARE AND THE
ACCOMPANYING MATERIALS. THERE IS
NO WARRANTY AGAINST INFRINGEMENT.
TP VISION DOES NOT WARRANT THAT
YOU WILL BE ABLE TO DOWNLOAD, COPY,
STORE, DISPLAY, TRANSFER, AND/OR PLAY
SECURE CONTENT.

9. Limited Software Warranty. TP VISION
provides the Software ‘as is’ and without
any warranty except that the Software will
perform substantially in accordance with the
documentation accompanying the Software for

a period of one year after your rst download,

installation or use of the Software, whichever

occurs rst. TP VISION’s entire liability and your

exclusive remedy for breach of this warranty
shall be, at TP VISION’ option, either (i) return of
the price paid by you for the Software (if any); or
(b) repair or replacement of the Software that
does not meet the warranty set forth herein and
that is returned to TP VISION with a copy of
your receipt. This limited warranty shall be void
if failure of the Software has resulted from any
accident, abuse, misuse or wrongful application.
Any replacement Software will be warranted for
the remainder of the original warranty period
or thirty (30) days, whichever is longer. This
limited warranty shall not apply to you if the
Software was provided to you free of charge on
an evaluation only basis.

10. NO OTHER WARRANTIES. EXCEPT
AS SET FORTH ABOVE, TP VISION AND ITS
LICENSORS DO NOT WARRANT THAT
THE SOFTWARE WILL OPERATE ERROR
FREE OR UNINTERRUPTED, OR WILL MEET
YOUR REQUIREMENTS. YOU ASSUME
ALL RESPONSIBILITIES FOR SELECTION
OF THE SOFTWARE TO ACHIEVE YOUR
INTENDED RESULTS, AND FOR THE
INSTALLATION OF, USE OF, AND RESULTS
OBTAINED FROM THE SOFTWARE. TO
THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, TP VISION AND ITS
LICENSORS DISCLAIM ALL WARRANTIES
AND CONDITIONS, WHETHER EXPRESS

11. LIMITATION OF LIABILITY. UNDER
NO CIRCUMSTANCES WILL TP VISION
OR ITS LICENSORS BE LIABLE FOR ANY
CONSEQUENTIAL, SPECIAL, INDIRECT,
INCIDENTAL OR PUNITIVE DAMAGES
WHATSOEVER, INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF
PROFITS OR REVENUES, BUSINESS
INTERRUPTION, LOSS OF BUSINESS
INFORMATION, LOSS OF DATA, LOSS OF
USE OR OTHER PECUNIARY LOSS, EVEN IF
TP VISION OR ITS LICENSORS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN NO EVENT SHALL TP VISION’
OR ITS LICENSORS’ AGGREGATE LIABILITY
FOR DAMAGES ARISING OUT OF THIS
AGREEMENT EXCEED THE GREATER OF THE
PRICE ACTUALLY PAID BY YOU FOR THE
SOFTWARE OR FIVE POUNDS STERLING
(5.00).

12. Trademarks. Certain of the product and
TP VISION names used in this Agreement, the
Software, and the printed user documentation
may constitute trademarks of the TP VISION,
its licensors or other third parties. You are not
authorized to use any such trademarks.

13. Export Administration. You agree that you
will not directly or indirectly, export or re­export the Software to any country for which
the United States Export Administration Act,
or any similar United States law or regulation
requires an export license or other U.S.
Government approval, unless the appropriate

export license or approval has rst been

obtained. By downloading or installing the
Software you agree to abide by this Export
provision.

36 EN-GB

14. Governing law. This Agreement is governed
by the laws of your country of residence

, without reference to its conict of laws

principles. Any dispute between you and TP
VISION regarding this Agreement shall be
subject to the non-exclusive jurisdiction of the
courts of your country of residence.

15. General. This Agreement contains the
entire agreement between you and TP VISION
and supersedes any prior representation,
undertaking or other communication or
advertising with respect to the Software
and user documentation. If any part of this
Agreement is held invalid, the remainder of this
Agreement will continue in full force and effect.
This Agreement shall not prejudice the statutory
rights of any party dealing as a consumer.

May 2016

Disclaimer
1

All application programs (APP) provided by

Philips Smart Television on the APP Store
are legally licensed and are duly protected
for the copyrights.

2 Where a user installs an APP by means

of USB/Network, the copyright does not
belong to Philips. Under no circumstances
shall Philips assume legal responsibility
because a user infringes upon the rights or
uses the programs illegally.

3 Under no circumstances shall Philips

assume any responsibility for the conditions
enumerated below as a result of installation
by a user at his or her discretion, either
directly or indirectly:

• The matching problem incurred by and

between Philips Smart Television and
the APP.

• Where the Philips Smart Television

breaks down and becomes damaged or
unusable.

• A transaction via a third party payment
and the product problem so deriving
therefrom.

Where you install an application program not
provided by Philips Smart Television APP Store,
you are deemed to have been fully aware of the
aforementioned clauses and disclaimer in full.

Open source

Open-source software

This TV set contains open source software.
TP Vision Europe B.V. hereby promises that,
according to the user’s requirements and in
accordance with the relevant license, we will
provide a copy of the corresponding source
code of the copyrighted open source package
used in this product.

This promise is valid within three years from
anyone’s purchase of this product and receiving
this information.

To obtain a source code, please send a letter in

Chinese to .....

[e-mail]
TP Vision Europe B.V.
Prins Bernhardplein 200
1097 JB Amsterdam

Open source license

README TP Vision Netherlands B.V. TV software
is part of the source code under the open
source license.
This is the source code for use on TV set of
TP Vision Netherlands B.V., which is carried
out under the distributed documents, either
the GNU General Public License (GPL) or the
Lesser General Public License (THA LGPL), or
any other open source licenses.It indicates that
to obtain the copy of the software can be found
in the instructions for use.

English

37EN-GB

TP Vision Netherlands B.V. does not make
any guarantees, nor any express or implied
warranties, including any warranty of

merchantability or tness for a particular

purpose. For the software, TP Vision Netherlands
B.V. provides the software support.The above
does not affect your warranty. For the statutory
right to purchase any TP Vision Netherlands B.V.
product (s).It applies only to the provision of the
source code.

Source: http://www.ffmpeg.org/ARM GPU drive
(r6p0-01rel0) Mali-400/450 GPU Linux Kernel
Device Drivers (r6p0-01rel0)

Source: malideveloper.arm.com Khronos Group

- OpenMAX (1.1.2)

Source: http://www.khronos.org/openmax/
iniParser - stand-alone ini Parser library in ANSI
C (4.0)

BusyBox (1.24.1)
Source: http://busybox.net/Das U-Boot ­Universal Bootloader (2010.06)

Source: http://www.denx.de/wiki/U-Boot/
WebHomeLinux Kernel (3.18)

Source: https://kernel.org/Android - platform ­frameworks - av (5.1.1_r1)

Source: http://source.android.com/index.html
libjpeg (6b)

Source: http://ijg.org/libpng - PNG Reference
Library (1.6.10)

Source: http://www.libpng.org/pub/png/libpng.
html Android - platform - external - libpng
(4.4.2_r1)

Source: http://source.android.com/index.html zlib
(1.2.8) ource: http://www.zlib.net/ NFS - nfs-utils
(1.3.2)

Source: http://linux-nfs.org/rp-pppoe (3.11)

Source: www.roaringpenguin.com/products/
pppoe Android (5.1.1_r1)

Source: https://android.googlesource.com Arp
Scan (1.9)

Source: http://ndevilla.free.fr/iniparser/Android ­platform - system - extras (4.4.2_r1)

Source: http://source.android.com/index.html
YAFFS - Yet Another Flash File System (master­583dbd9)

Source: http://www.yaffs.net/mtd-utils (1.5.0)

Source: http://git.infradead.org/mtd-utils.git ntfs
driver (v1r1_ntfs_svn_21204) Linaro GCC (4.9-

2015.06)

Source: https://www.linaro.org/Android ­platform - external - aac (4.4.2_r1)

Source: http://source.android.com/index.html
RealAudio 8 Low Bitrate music (1.2.2.1) alsa-lib
(1.0.28)

Source: http://www.alsa-project.org/main/index.
php/Main_Page alsa-utils (1.0.28)

Source: http://www.alsa-project.org/main/index.
php/Main_Page PolarSSL (1.3.7)

Source: https://polarssl.org/my-project-oks
(r3546)

Source: http://code.google.com/p/my-project­oks/Curl and Libcurl (7.42.1)

Source: http://www.nta-monitor.com/tools­resources/security-tools/arp-scan ISC DHCP
(4.3.3)

Source: http://www.isc.org/downloads/dhcp/
FFmpeg (2.8)

38 EN-GB

Source:http://curl.haxx.se/

China Rohs law

Requirement of Usage Control on Electrical and Electronic Product
Hazardous Substances

Names and Levels of Hazardous Substances Contained in this Product

Hazardous Substances

Lead

Part Name

Plastic frame

Rear chassis

LCD

CCFL

panel

LED

The circuit board
assemblies*

Base

Power cable

Other materials

Remote Control

*: The circuit board assemblies, including the printed circuit board and its component parts, such as resistors,
capacitors, integrated circuits and connectors.

This table is compiled in accordance with SJ/T 11364 requirements.
O: indicates that the hazardous substance contained in all of the homogeneous materials for this part is below
the limit requirement in GB/T 26572.
X: indicates that the hazardous substance contained in at least one of the homogeneous materials used for this
part is above the limit requirement in GB/T 26572.

Note: In the parts marked “X” above, some of the hazardous substances have exceeded the limit requirements
set out in GB/T 26572 in order to meet functional requirements, but are in compliance with the European
Union’s RoHS requirements (under the exemption section).

Mercury

(Pb)

○ ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○

× × ○ ○ ○ ○

× ○ ○ ○ ○ ○

× ○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○

× ○ ○ ○ ○ ○

× ○ ○ ○ ○ ○

× ○ ○ ○ ○ ○

(Hg)

Cadmium

(Cd)

Hexavalent

chromium

(Cr(VI))

Polybrominated
biphenyls (PBB)

Polybrominated
diphenyl ethers

(PBDE)

English

Environmental Protection Use Period

This electrical and electronic product contains some hazardous substances.You may be safe to use it during the
environment-friendly use period, and please hand it over to recycle system after environment-friendly use period
exceeded.

Suggestive description of the Recycling Administrative
Regulations for Waste Electrical and Electronics Products

In order to care and protect the Earth in a better way, when the user no longer needs to use this product, or
it has reached the end of the use period, please adhere to the national and applicable laws in relation to the
recycling management of waste electrical and electronics products.

39EN-GB