Philips 32PHT5302/12, 43PFT5302/12 Schematic

TPM17.2E

Chassis name Platform Model name

32PHS5302/12

32PHT5302/12

TPM17.2E LA MTK5800

43PFS5302/12

43PFT5302/12

49PFS5302/12

Published by CQZ/SC 1710 Quality Subject to modification 3122 785 20370

© TP Vision Netherlands B.V.

2016

All rights reserved. Specifications are subject to change without notice. Trademarks are the
property of Koninklijke Philips Electronics N.V. or their respective owners.
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust
earlier supplies accordingly.
PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.

2017-March-10

1.Product information……….……………………………………………………………………………………3

2.Connections overview……..…..…..………………..…………………………………………………………6

3.Mechanical Instructions………………….…………………………………………………………………….7

Cable dressing (32" 5032 series)………………………………………………………………………………7
Cable dressing (43" 5032 series)………………………………………………………………………………7

Cable dressing (49" 5032 series)………………………………………………………………………………8

Assembly/Panel Removal ………………………………………………………………………………………8

4.Service Modes…………….……………….………………….…………………………………………….….12

5.Software upgrading, Error Code and Panel Code………...……………………………………………..16

6.Circuit Descriptions…..……………………….………………………………………………………………20

7.IC Data Sheet……...……………………………………………………………………………………….…..27

8.Circuit Diagrams……………...……………………………………………………………………………….30

8.1 715G7734 PSU………………………………………………………………………..……………………30

8.2 715G7574 PSU………………………………………………………………………..……………………32

8.3 715G8198 SSB……………………………………………………………………………………………..33

8.3 715G7055 IR/LED Panel………………………………………………..…………………………………49

8.4 715G7088 Keyboard control panel……………………………………………………………………….50

9.Styling Sheet……………….…………………….……………………………………………………………..51

5032 series 32"………………………………………………………………………………………………….51
5032 series 43"………………………………………………………………………………………………….52

5032 series 49"………………………………………………………………………………………………….53

Published by CQZ/SC 1710 Quality Subject to modification 3122 785 20370

© TP Vision Netherlands B.V.

2016

All rights reserved. Specifications are subject to change without notice. Trademarks are the
property of Koninklijke Philips Electronics N.V. or their respective owners.
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust
earlier supplies accordingly.
PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.

2017-March-10

1. Product information

1.1 Product Fiche
32PHx5301

• Energy Efficiency Class : A+

• Visible Screen Size : 80 cm / 32 inch

• On Mode Power Consumption (W) : 47 W

• Annual Energy Consumption (kWh) * : 68 kWh

• Standby Power Consumption (W) **: 0.30 W

• Display Resolution (Pixels) : 1366 x 768p

43PFx5301

• Energy Efficiency Class : A++

• Visible Screen Size : 108 cm / 43 inch

• On Mode Power Consumption (W) : 34 W

• Annual Energy Consumption (kWh) * : 50 kWh

• Standby Power Consumption (W) **: 0.30 W

• Display Resolution (Pixels) : 1920 x 1080p

49PFx5301

• Energy Efficiency Class : A++

• Visible Screen Size : 123 cm / 49 inch

• On Mode Power Consumption (W) : 37 W

•Annual Energy Consumption (kWh) * : 54 kWh

• Standby Power Consumption (W) **: 0.30 W

•Display Resolution (Pixels) : 1920 x 1080p

* Energy consumption kWh per year, based on the power consumption of the television operating 4 hours per day for

365 days. The actual energy consumption depends on how the television is used.

** When the TV is turned off with the remote control and no function is active.

1.2 Power

Product specifications are subject to change without notice. For more specification details of this product, see

www.philips.com/support

• Mains power : AC 220-240V +/-10%

• Ambient temperature : 5°C to 35°C

• Power saving features : Eco mode, Picture mute (for radio), Auto switch-off timer, Eco settings menu.

For power consumption information, see chapter Product Fiche.

The power rating stated on the product typeplate is the power consumption for this product during normal household

use (IEC 62087 Ed.2). The maximum power rating, stated between brackets, is used for electrical safety (IEC

60065Ed. 7.2

1.3 Reception

• Aerial input : 75 ohm coaxial (IEC75)

• Tuner bands : Hyperband, S-Channel, UHF, VHF

• DVB : DVB-T2, DVB-C (cable) QAM

• Analogue video playback : SECAM, PAL

• Digital video playback : MPEG2 SD/HD (ISO/IEC 13818-2), MPEG4 SD/HD (ISO/IEC 14496-10)

• Digital audio playback (ISO/IEC 13818-3)

• Satellite aerial input : 75 ohm F-type

• Input frequency range : 950 to 2150MHz

• Input level range : 25 to 65 dBm

• DVB-S/S2 QPSK, symbol rate 2 to 45M symbols,

SCPC and MCPC

•LNB : DiSEqC 1.0, 1 to 4 LNBs supported, Polarity selection 14/18V, Band selection 22kHz, Tone burstmode, LNB

current 300mA max

1.4 Display type

Diagonal screen size

•32PHx5301 : 80 cm / 32 inch

• 43PFx5301 : 108 cm / 43 inch

• 49PFx5301 : 123 cm / 49 inch

Display resolution

• 1366 x 768p (for 32”)

• 1920 x 1080p（43”&49”）

1.5 Display input resolution

Video formats

Resolution — Refresh rate

•480i - 60 Hz

• 480p - 60 Hz

• 576i - 50 Hz

• 576p - 50 Hz

• 720p - 50 Hz, 60 Hz

• 1080i - 50 Hz, 60 Hz

• 1080p - 24 Hz, 25 Hz, 30 Hz

Computer formats

Resolutions (amongst others) for 32”

• 640 x 480p - 60 Hz

• 800 x 600p - 60 Hz

•1024 x 768p - 60 Hz

•1280 x 768p - 60 Hz

• 1360 x 765p - 60 Hz

• 1360 x 768p - 60 Hz

• 1280 x 1024p - 60 Hz

Resolutions (amongst others) for 43”&49”

• 640 x 480p - 60 Hz

• 800 x 600p - 60 Hz

• 1024 x 768p - 60 Hz

• 1280 x 768p - 60 Hz

• 1360 x 765p - 60 Hz

• 1360 x 768p - 60 Hz

• 1280 x 1024p - 60 Hz

• 1920 x 1080p - 60 Hz

1.6 Connectivity

TV Side

• HDMI 1 in - MHL

• USB 1

•USB 2

• 1x Common Interface slot: CI+/CAM

• Headphones - Stereo mini-jack 3.5mm

TV Rear

• CVBS/Y Pb Pr : CVBS/Y Pb Pr, Audio L/R

•• HDMI 2 in - ARC

• Audio out - Optical Toslink

• Network LAN - RJ45

• Antenna (75 ohm)

•Satellite tuner

1.7 Sound

• HD Stereo

• Output power (RMS) : 16W

• Dolby® Digital Plus

• DTS 2.0+ Digital out ™

1.8 Multimedia

Connections

•USB 2.0

• Ethernet LAN RJ-45

• Wi-Fi 802.11a/b/g/n (built-in)

Supported USB file systems

• FAT 16, FAT 32, NTFS

Playback formats

• Containers : 3GP, AVCHD, AVI, MPEG-PS, MPEG-TS,MPEG-4, Matroska (MKV), Quicktime (MOV, M4V,M4A),

Windows Media (ASF/WMV/WMA)

• Video Codecs : MPEG-1, MPEG-2, MPEG-4 Part 2, MPEG-4 Part 10 AVC (H.264), VC-1, WMV9, HEVC,VP9

• Audio Codecs : AAC, HE-AAC (v1/v2), AMR-NB,Dolby Digital, Dolby Digital Plus, DTS 2.0 + Digital Out™,

MPEG-1/2/2.5 Layer I/II/III (includes MP3), WMA (v2 to v9.2), WMA Pro (v9/v10)

• Subtitles :

– Formats : SAMI, SubRip (SRT), SubViewer (SUB), MicroDVD (TXT), mplayer2 (TXT), TMPlayer (TXT)

– Character encodings : UTF-8, Central Europe and Eastern Europe (Windows-1250), Cyrillic (Windows-1251), Greek

(Windows-1253), Turkish (Windows-1254), Western Europe (Windows-1252)

• Image Codecs : JPEG

• Limitations :

– Maximum supported total bit rate for a media file is 30Mbps.

– Maximum supported video bit rate for a media file is 20Mbps.

– MPEG-4 AVC (H.264) is supported up to High Profile @ L4.1.

– VC-1 is supported up to Advanced Profile @ L3. Wi-Fi Certified

This TV supports Miracast certified devices. Supported media server software (DMS)

•You can use any DLNA V1.5 certified media server software (DMS class).

• You can use the Philips TV Remote app (iOS and Android) on mobile devices. Performance may vary, depending on

the capabilities of the mobile device and the software used.

ESD regulations

This apparatus meets performance criteria A for ESD. In case the apparatus does not recover in file sharing mode due

to electrostatic discharge, user interference

2. Connections Overview

3. Mechanical Instructions

3.1 Cable Dressing

Cable dressing (32" 5302 series)

Cable dressing (43" 5302 series)

Cable dressing (49" 5302 series)

3.2 Assembly/Panel Removal

Instructions below apply to the 32PHS5302/12, but will be similar for other 32"/43"/49"Pxx5302 series models.

3.2.1 Stand removal

1. Remove the fixation screws [1] that secure the stand

2. Take the stand bracket out from the set.

3.2.2 Rear Cover

Warning: Disconnect the mains power cord before removing the rear cover.

1. Remove fixation screws [2] and [3] that secure the Rear Cover

2. Unplug the connector [4] from SSB.

3. Gently lift the rear cover from the TV. Make sure that wires and cables are not damaged while lifting the rear cover from the set

Rear cover removal[1]

Rear cover removal[2]

3.2.3 Keyboard Control Unit

1. Release the connector [2] from the SSB Board.
Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors!

2. Remove all the fixation screws from the keyboard control panel [1] and take it out from the Back cover

When defective, replace the whole unit.

3.2.4 Small Signal Board (SSB)

Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the

SSB.

1. Release the clips from the LVDS connector that connect with the SSB[1].

Caution: be careful, as these are very fragile connectors!

1. Unplug all other connectors [2] .

3. Remove all the fixation screws from the SSB [3].

4. The SSB can now be shifted from side connector cover, then lifted and taken out of the I/O bracket.

3.2.5 Power Supply Unit (PSU)

Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the

PSU.

1. Gently unplug all connectors from the PSU.

2. Remove all fixation screws from the PSU.

3. The PSU can be taken out of the set now.

3.2.6 IR board Control Unit

1. Unplug the connector from the SSB.

Caution: be careful, as these are very fragile connectors!

3. Remove all the fixation screws [1], [2] and connector [3] from the IR board control unit.

3. Remove the IR lens [4], IR board [5] from the DECO_REAR_COVER.

When defective, replace the whole unit.

3.2.7 Speakers

1. Gently release the tapes that secure the speaker cables.

2. Unplug the speaker connector from the SSB.

3. Take the speakers out.

When defective, replace the both units.

3.2.8 WIFI module

1. Unplug the connector from the SSB..

2. Remove fixation screw that secure the WIFI module,
When defective, replace the whole unit.

3.2.9 LCD Panel

1. Remove the SSB as described earlier.

2. Remove the PSU as described earlier.

3. Remove the keyboard control panel as described earlier.

4. Remove the stand bracket as described earlier.

5. Remove the IR/LED as described earlier.

6. Remove the fixations screws that fix the metal clamps to the front bezel. Take out those clamps.

7. Remove all other metal parts not belonging to the panel.

8. Lift the LCD Panel from the bezel.

When defective, replace the whole unit.

4. Service Modes

4.1 Service Modes

The Service Mode feature is split into following parts:

 Service Alignment Mode (SAM).

 Factory Mode.

 Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set.

SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. Some features are:

 Make alignments (e.g. White Tone), reset the error buffer(SAM and Factory Mode).

 Display information (“SAM” indication in upper right corner of screen, error buffer, software version, operating hours,options and option codes,

sub menus).

The CSM is a Service Mode that can be enabled by the consumer. The CSM displays diagnosis information, which the customer can forward to the

dealer or call centre. In CSM mode, “CSM”, is displayed in the top right corner of the screen. The information provided in CSM and the purpose of

CSM is to:

 Increase the home repair hit rate.

 Decrease the number of nuisance calls.

 Solved customers’ problem without home visit.

Note: For the new model range, a new remote control (RC) is used with some renamed buttons. This has an impact on the activation of the Service

modes. For instance the old “MENU” button is now called “HOME” (or is indicated by a “house” icon).

4.2 Service Alignment Mode (SAM)

Purpose

 To modify the NVM.

 To display/clear the error code buffer.

 To perform alignments.

Specifications

 Operation hours counter (maximum five digits displayed).

 Software version, error codes, and option settings display.

 Error buffer clearing.

 Option settings.

 Software alignments (White Tone).

 NVM Editor.

 Set screen mode to full screen (all content is visible).

How to Activate SAM

To activate SAM, use one of the following methods:

 Press the following key sequence on the remote control transmitter: “062596”, directly followed by the “INFO/OK” button. Do not allow the

display to time out between entries while keying the sequence.

 Or via ComPair.

After entering SAM, the following items are displayed,

with “SAM” in the upper right corner of the screen to indicate that the television is in Service Alignment Mode.

How to Navigate

 In the SAM menu, select menu items with the UP/DOWN keys on the remote control transmitter. The selected item will be indicated. When not

all menu items fit on the screen, use the UP/DOWN keys to display the next/previous menu items.

 With the “LEFT/RIGHT” keys, it is possible to:

– (De) activate the selected menu item.
– (De) activate the selected sub menu.
– Change the value of the selected menu item.

 When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the

background).

How to Store SAM Settings

To store the settings changed in SAM mode (except the RGB Align settings), leave the top level SAM menu by using the POWER button on the

remote control transmitter or the television set. The mentioned exceptions must be stored separately via the STORE button.

How to Exit SAM

Use one of the following methods:

 Switch the set to STANDBY by pressing the mains button on the remote control transmitter or the television set.

 Via a standard RC-transmitter, key in “00” sequence.

Note: When the TV is switched “off” by a power interrupt while in SAM, the TV will show up in “normal operation mode” as soon as the power is

supplied again. The error buffer will not be cleared.

SAM mode overview

4.3 Factory mode:

Purpose

 To perform extended alignments.

Specifications

 Displaying and or changing Panel ID information.

 Displaying and or changing Tuner ID information.

 Error buffer clearing.

 Various software alignment settings.

 Testpattern displaying.

 Public Broadcasting Service password Reset.

 etc.

How to Activate the Factory mode

To activate the Factory mode, use the following method:

 Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the

“Back/Return” button. Do not allow the display to time out between entries while keying the sequence.

After entering the Factory mode, we can see many items displayed, use the UP/DOWN keys to display the next/previous menu items

Factory mode overview

How to Exit the Factory mode

Use one of the following methods:

 Select EXIT_FACTORY from the menu and press the “OK” button.

Note: When the TV is switched “off” by a power interrupt, or normal switch to “stand-by” while in the factory mode, the TV will show up in “normal

operation mode” as soon as the power is supplied again. The error buffer will not be cleared.

4.4 Customer Service Mode (CSM)

Purpose

The Customer Service Mode shows error codes and information on the TVs operation settings.The call centre can instruct the customer (by

telephone) to enter CSM in order to identify the status of the set.This helps the call centre to diagnose problems and failures in the TV set before

making a service call.

The CSM is a read-only mode; therefore, modifications are not possible in this mode.

Specifications

 Ignore “Service unfriendly modes”.

 Line number for every

line (to make CSM language independent).

 Set the screen mode to full

screen (all contents on screen is visible).

 After leaving the Customer Service Mode, the original settings are restored.

 Possibility to use “CH+” or “CH-” for channel surfing, or enter the specific channel number on the RC.

How to Activate CSM

To activate CSM, press the following key sequence on a standard remote control transmitter: “123654” (do not allow the display to time out

between entries while keying the sequence). After entering the Customer Service Mode, the following items are displayed. use the Right/Left keys

to display the next/previous menu items

Note: Activation of the CSM is only possible if there is no (user) menu on the screen!

CSM Overview

How to Navigate

By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus.

How to Exit CSM

To exit CSM, use one of the following methods.

 Press the MENU/HOME button on the remote control transmitter.

 Press the POWER button on the remote control transmitter.

 Press the POWER button on the television set.

5. Software Upgrading, Error code and Panel Code

5.1 Software Upgrading

Step 1: Ready for F/W Upgrade

1. Rename the software as “autorun.upg”

2.

Prepare a USB memory.

3. Copy the software to USB flash disk(root directory).

Note the version of this F/W before you change the software file name.

Step 2: F/W Upgrade

1. Plug the USB memory on the USB port on the side I/O port of TV (Please connect to USB 2.0 port, not recommend USB3.0 port)

2.

AC on (Power plug)

3. TV will upgrade automatically as detect the software