Philips 37FD9954-69S, 42FD9954-69C, 42FD9954-69Y, 32FD9954-69S, 42FD9954-69S User Manual
...
~ MAINS
RS232
DVI-D
Y/C S-VHS
L
R
L
R
AUDIO IN AUDIO IN
G/Y/Y
CVBS B/Pb/Cb
R/Pr/Cr V
H
AUDIO IN
R
VGA 1
VGA 2
RC-OUT
AV2 AV1 AV3
L
AUDIO IN
VGA 1VGA 2DVI-D
2
1
1015.5 cover 03-10-2003 11:48 Pagina 2
1
Unpacking and wall mounting instructions
For the unpacking instructions follow the illustrated steps printed on the
packaging (outside and inside). For the wall mounting instructions follow the
illustrated steps ‘ to § printed on the separate template and in the
supplied booklet.
Make sure that the wall mount is being fixed securely enough so that it meets
safety standards.The weight of the monitor (excl. packaging) is about 24 kg,
30 kg or 35.5 kg, depending on the screen size (32”, 37” or 42”).
Note: stands are optional acccessories. Consult your dealer.
To prevent any unsafe situations, no naked flame sources, such as lighted candles,
should be placed on or in the vicinity.Avoid heat, direct sunlight and exposure to
rain or water.
The equipment shall not be exposed to dripping or splashing and no objects filled
with liquids, such as vases, shall be placed on it.
Connect your computer
Directly to the monitor
& Connect one end of a VGA cable 1 to the video card of the computer and
the other end to the
VGA 1 connector at the rear side of the monitor. Fix the
connectors firmly with the screws on the plug.
é In case of a Multimedia computer, connect the audio cable 2 to the audio
outputs of your Multimedia computer and to the
AUDIO VGA 1 R (right) and
L (left) inputs of the monitor.
VGA 2:The video connector for VGA 2 can be programmed to become an input or an
output via the Setup menu, see p. 6.The function of being input or output is
determined by the used mode. If the monitor is used in video mode, the VGA 2
connector is VGA output. If the monitor is used in monitor mode,the connector is VGA
input or output.
To a electronic receiver box
See the handbook of the receiver box.
& Connect one end of a VGA cable to the video card of the computer and the
other end to the
PC/MAC IN connector at the rear side of the receiver box.
Fix the connectors firmly with the screws on the plug.
é In case of a Multimedia computer, connect the audio cable to the audio
outputs of your Multimedia computer and to the
AUDIO IN R (right) and L
(left) inputs of the receiver box.
Note: Only use the VGA cable supplied with the monitor.
Daisy chaining
The Loop Through facility makes it possible to make a daisy chain with a
second monitor.
“ Connect one end of another VGA cable to the VGA 2 connector at the rear
side of the monitor and the other end to the
VGA 1 connector of a second
monitor.
‘ In case of a Multimedia computer, also connect audio cables to the AUDIO L
and R outputs of the original monitor and to the AUDIO L and R inputs of the
second monitor.
The RC out jack next to the
VGA 2 connector makes it possible to daisy chain
remote control signals to other equipment.
This output cannot be used to daisy chain a second monitor.
I
English
1015.5 en 12-11-2003 11:12 Pagina 1
min.
1 m
L
R
RS232
~ MAINS
VGA 1
VGA 1
VGA 1VGA 2DVI-D
AUDIO
RC-OUT
VGA 2
L
R
Y/C S-VHS
AUD
DVI-D
AV2
1
2
22
VGA 640x480 60, 72, 75, 85 Hz
Wide VGA 848x480 60 Hz
Wide VGA 852x480 60 Hz
MAC 640x480 66.67 Hz
MAC 832x624 74.55 Hz
MAC 1024x768 74.93 Hz
MAC 1152x870 75 Hz
SVGA 800x600 56, 60, 72, 75, 85 Hz
XGA 1024x768 60, 70, 75, 85 Hz
SXGA 1280x1024 60 Hz,
72 Hz (not with DVI-D source)
When a VGA computer is connected, the display selection is made
automatically.
A message is displayed when the monitor does not support the connected
VGA mode. Switch your computer to a correct display mode.
R6 / AA
B
Computer Display modes
Operation
& Insert the mains plug supplied into the mains inlet at the back of the
monitor and in the wall socket. For safety, please, only use the supplied rimearthed mains cord which has to be inserted in a grounded socket.
é Remote control: remove the cover of the battery compartment.
Insert the 2 batteries supplied (Type LR6/AA-1.5V).
The batteries supplied do not contain the heavy metals mercury and cadmium.
Nevertheless in many countries batteries may not be disposed of with your
household waste. Please check on how to dispose of batteries according to local
regulations.
“ Make sure that your receiver box and/or PC are switched on and that your
PC is in the correct display mode.
‘ Switch the monitor on : Press the power key B at the right side of the
monitor.
A green indicator lights up and the screen comes on.
When the monitor does not receive a supported VGA signal and is not
connected to a receiver box, the screen switches to standby and the red
indicator lights up.
When you switch on your monitor for the first time, and the monitor is
not connected to an electronic receiver box, the language menu
automatically appears on the screen.The explanation appears in different
languages one at a time.
Follow the instructions on screen to select the correct language or see
Setup menu, Language, p. 6.
1015.5 en 12-11-2003 11:12 Pagina 2
3Use of the remote control 3
POWER
BRIGHTNESS
CONTRAST
ZOOM OUTZOOM INZOOM ON/OFF
VGA AV1 AV2 AV3
MUTE
AV MUTE
q
1
2
3
4
5
6
7
8
9
0
V
CH/PR
MENU
OK
¬
B
VGA
press repeatedly to select your computer
connected to the
VGA 1 or 2 connector or
to the
DVI-D connector.
AV1 , AV 2, AV3
press to select the peripherals connected
to the connector indicated on the monitor.
Note: in case the monitor is operating in
combination with an electronic receiver box, the
AV inputs on the monitor will be disabled and
the VGA2 connector becomes an output.
V press - or + to adjust the volume
¬ Mute button
Mute the sound or restore it
CH/PR Program selection
To browse through the sources selected.
B to switch to standby or on again
MENU to switch the menu on/off
cursor buttons to select your choice and
to alter a selected adjustment.
OK to activate your choice
AV MUTE to mute the picture and the
sound or restore it (if the monitor is
used in monitor mode).
When activated a green indicator starts
blinking in front of the monitor.
q Picture format
See Picture 2 menu, p. 5.
Press the q button to switch between
the different picture formats.
BRIGHTNESS +/-
to adjust the brightness level of the picture
CONTRAST +/-
to adjust the contrast level of the picture
ZOOM ON/OFF
to activate/de-activate the zoom function.
See p. 5.
ZOOM IN/OUT to adjust the zoom factor
and to change the magnification of the
picture when zoom is activated. See p. 5.
Use of the remote control
On screen information
When the monitor is used in the monitor mode, information about the active
source (
AV1 , AV 2, AV3, VGA1, VGA2 or DVI-D), and the supported video,VGA or
HD-format of the selected source is displayed on the screen together with the
selected picture format and icons informing about selected sound mode and AV or
audio mute.
1015.5 en 12-11-2003 11:12 Pagina 3
Loading...