Philips 37FD9954-69S, 42FD9954-69C, 42FD9954-69Y, 32FD9954-69S, 42FD9954-69S User Manual

...

0 (0)

~ MAINS

RS232

DVI-D

Y/C S-VHS

AUDIO IN AUDIO IN

G/Y/Y

CVBS B/Pb/Cb

R/Pr/Cr V

AUDIO IN

VGA 1

VGA 2

RC-OUT

AV2 AV1 AV3

AUDIO IN

VGA 1VGA 2DVI-D

1015.5 cover 03-10-2003 11:48 Pagina 2

Unpacking and wall mounting instructions

For the unpacking instructions follow the illustrated steps printed on the packaging (outside and inside). For the wall mounting instructions follow the illustrated steps ‘ to § printed on the separate template and in the

supplied booklet. Make sure that the wall mount is being fixed securely enough so that it meets

safety standards.The weight of the monitor (excl. packaging) is about 24 kg, 30 kg or 35.5 kg, depending on the screen size (32”, 37” or 42”).

Note: stands are optional acccessories. Consult your dealer.

To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be placed on or in the vicinity.Avoid heat, direct sunlight and exposure to rain or water.

The equipment shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on it.

Connect your computer

Directly to the monitor

& Connect one end of a VGA cable 1 to the video card of the computer and

the other end to the

VGA 1 connector at the rear side of the monitor. Fix the

connectors firmly with the screws on the plug.

é In case of a Multimedia computer, connect the audio cable 2 to the audio

outputs of your Multimedia computer and to the

AUDIO VGA 1 R (right) and

L (left) inputs of the monitor.

VGA 2:The video connector for VGA 2 can be programmed to become an input or an output via the Setup menu, see p. 6.The function of being input or output is determined by the used mode. If the monitor is used in video mode, the VGA 2 connector is VGA output. If the monitor is used in monitor mode,the connector is VGA input or output.

To a electronic receiver box

See the handbook of the receiver box.

& Connect one end of a VGA cable to the video card of the computer and the

other end to the

PC/MAC IN connector at the rear side of the receiver box.

Fix the connectors firmly with the screws on the plug.

é In case of a Multimedia computer, connect the audio cable to the audio

outputs of your Multimedia computer and to the

AUDIO IN R (right) and L

(left) inputs of the receiver box.

Note: Only use the VGA cable supplied with the monitor.

Daisy chaining

The Loop Through facility makes it possible to make a daisy chain with a second monitor.

“ Connect one end of another VGA cable to the VGA 2 connector at the rear

side of the monitor and the other end to the

VGA 1 connector of a second

monitor.

‘ In case of a Multimedia computer, also connect audio cables to the AUDIO L

and R outputs of the original monitor and to the AUDIO L and R inputs of the second monitor.

The RC out jack next to the

VGA 2 connector makes it possible to daisy chain

remote control signals to other equipment. This output cannot be used to daisy chain a second monitor.

English

1015.5 en 12-11-2003 11:12 Pagina 1

min.

1 m

RS232

~ MAINS

VGA 1

VGA 1VGA 2DVI-D

AUDIO

RC-OUT

VGA 2

Y/C S-VHS

AUD

DVI-D

AV2

VGA 640x480 60, 72, 75, 85 Hz Wide VGA 848x480 60 Hz Wide VGA 852x480 60 Hz MAC 640x480 66.67 Hz MAC 832x624 74.55 Hz MAC 1024x768 74.93 Hz MAC 1152x870 75 Hz SVGA 800x600 56, 60, 72, 75, 85 Hz XGA 1024x768 60, 70, 75, 85 Hz SXGA 1280x1024 60 Hz,

72 Hz (not with DVI-D source)

When a VGA computer is connected, the display selection is made automatically.

A message is displayed when the monitor does not support the connected VGA mode. Switch your computer to a correct display mode.

R6 / AA

Computer Display modes

Operation

& Insert the mains plug supplied into the mains inlet at the back of the

monitor and in the wall socket. For safety, please, only use the supplied rimearthed mains cord which has to be inserted in a grounded socket.

é Remote control: remove the cover of the battery compartment.

Insert the 2 batteries supplied (Type LR6/AA-1.5V).

The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless in many countries batteries may not be disposed of with your household waste. Please check on how to dispose of batteries according to local regulations.

“ Make sure that your receiver box and/or PC are switched on and that your

PC is in the correct display mode.

‘ Switch the monitor on : Press the power key B at the right side of the

monitor. A green indicator lights up and the screen comes on. When the monitor does not receive a supported VGA signal and is not connected to a receiver box, the screen switches to standby and the red indicator lights up.

When you switch on your monitor for the first time, and the monitor is not connected to an electronic receiver box, the language menu automatically appears on the screen.The explanation appears in different languages one at a time. Follow the instructions on screen to select the correct language or see Setup menu, Language, p. 6.

1015.5 en 12-11-2003 11:12 Pagina 2

3Use of the remote control 3

POWER

BRIGHTNESS

CONTRAST

ZOOM OUTZOOM INZOOM ON/OFF

VGA AV1 AV2 AV3

MUTE

AV MUTE

CH/PR

VGA

press repeatedly to select your computer connected to the

VGA 1 or 2 connector or

to the

DVI-D connector.

AV1 , AV 2, AV3

press to select the peripherals connected to the connector indicated on the monitor.

Note: in case the monitor is operating in combination with an electronic receiver box, the AV inputs on the monitor will be disabled and the VGA2 connector becomes an output.

V press - or + to adjust the volume

¬ Mute button

Mute the sound or restore it

CH/PR Program selection

To browse through the sources selected.

B to switch to standby or on again

MENU to switch the menu on/off

cursor buttons to select your choice and to alter a selected adjustment.

OK to activate your choice

AV MUTE to mute the picture and the

sound or restore it (if the monitor is used in monitor mode). When activated a green indicator starts blinking in front of the monitor.

q Picture format

See Picture 2 menu, p. 5. Press the q button to switch between

the different picture formats.

BRIGHTNESS +/-

to adjust the brightness level of the picture

CONTRAST +/-

to adjust the contrast level of the picture

ZOOM ON/OFF

to activate/de-activate the zoom function. See p. 5.

ZOOM IN/OUT to adjust the zoom factor

and to change the magnification of the picture when zoom is activated. See p. 5.

Use of the remote control

On screen information

When the monitor is used in the monitor mode, information about the active source (

AV1 , AV 2, AV3, VGA1, VGA2 or DVI-D), and the supported video,VGA or

HD-format of the selected source is displayed on the screen together with the selected picture format and icons informing about selected sound mode and AV or audio mute.

1015.5 en 12-11-2003 11:12 Pagina 3

+ 7 hidden pages