Philips 32PHH4101-88 Instruction manual

www.philips.com/welcome

4201 series

User Manual

32PFH4101

32PFT4101 32PFT4101

32PHH4101

32PHT4101

40PFH4101

40PFT4101

48PFH4101

48PFT4101

1 TV Tour 3

1.1 Pause TV and recordings 3

1.2 EasyLink 3

2 Setting up 4

2.1 Read safety 4

2.2 TV stand and wall mounting 4

2.3 Tips on placement 4

2.4 Power cable 4

2.5 Antenna cable 4

2.6 Satellite dish 5

3 Connect devices 6

3.1 About connections 6

3.2 Common interface - CAM 8

3.3 Set-top box - STB 8

3.4 Satellite receiver 8

3.5 Home Theatre System - HTS 9

3.6 Blu-ray Disc player 10

3.7 DVD player 10

3.8 Game console 10

3.9 USB Hard Drive 11

3.10 USB flash drive 12

3.11 Camcorder - HDMI 12

3.12 Computer 12

3.13 Headphones 12

4 Switch on 14

4.1 On, Standby or Off 14

4.2 Keys on TV (For 4100, 4200, 4101, 4111, 4201, 6300,

630) series 14

4.3 Sleep timer 14

4.4 Switch Off Timer 14

5 Remote control 15

5.1 Key overview (For 4000, 4100, 4200, 4101, 4111, 4201, 5210 series) 15

5.2 IR sensor 16

5.3 Batteries 16

5.4 Cleaning 16

6 TV channels 17

6.1 Channel Lists 17

6.2 Watching TV channels 17

6.3 Channel list copy 21

7 Channel installation - Antenna, Cable

7.1 Update channels 23

7.2 Reinstall channels 23

7.3 DVB-T or DVB-C 23

7.4 Manual Installation 24

8 TV guide 26

8.1 What you need 26

8.2 Using the TV guide 26

9 Recording and pause TV 28

9.1 Recording 28

9.2 Pause TV 29

10 Sources 30

10.1 Switch to a device 30

10.2 From standby 30

10.3 EasyLink 30

11 Timers and clock 31

11.1 Sleep timer 31

11.2 Clock 31

11.3 Switch off timer 31

12 Videos, Photos and Music 32

12.1 From a USB connection 32

12.2 Play your videos 32

12.3 View your photos 32

12.4 Play your music 33

13 Settings 34

13.1 Picture 34

13.2 Sound 37

13.3 General settings 39

14 Specifications 41

14.1 Environmental 41

14.2 Reception for PxH / PxT models 42

14.3 Display 42

14.4 Power 43

14.5 Dimensions and weights 43

14.6 Connectivity 43

14.7 Sound 43

14.8 Multimedia 43

15 Software 45

15.1 Software update 45

15.2 Software version 45

15.3 Open source software 45

15.4 Open source license 45

16 Troubleshooting and support 48

16.1 Troubleshooting 48

16.2 Register 49

16.3 Help 49

16.4 Online help 49

16.5 Consumer Care / Repair 50

17 Safety and care 51

17.1 Safety 51

17.2 Screen care 52

18 Terms of use, copyrights and licenses

18.1 Terms of use 53

18.2 Copyrights and licenses 53

Index 55

TV Tour

1.1

Pause TV and recordings

If you connect a USB Hard Drive, you can pause and record a broadcast from a digital TV channel.

Pause your TV and answer that urgent phone call or simply take a break during a sports match, while the TV stores the broadcast on the USB Hard Drive. You can start watching again later.

With a USB Hard Drive connected, you can also record digital broadcasts. You can record while you are watching a programme or schedule a recording of an upcoming programme.

1.2

EasyLink

With EasyLink you can operate a connected device, like a Bluray Disc player, with the remote control of the TV.

EasyLink uses HDMI CEC to communicate with the connected devices.

Setting up

TP Vision Europe B.V. bears no responsibility for improper mounting or any mounting that results in accident or injury.

2.1

Read safety

Read the safety instructions first before you use the TV.

In Help, go to Safety and care > Safety.

2.2

TV stand and wall mounting

TV stand

You can find the instructions for mounting the TV stand in the Quick Start Guide that came with the TV. In case you lost this guide, you can download it from

www.philips.com.

Use the product type number of the TV to look for the Quick Start Guide to download.

Wall mounting

For 4101, 4111 series

Your TV is also prepared for a VESA-compliant wall mount bracket (sold separately). Use the following VESA code when purchasing the wall mount . . . To fix the bracket securely, use screws with a length indicated in the drawing.

2.3

Tips on placement

- Position the TV where light does not shine directly on the screen.

- Position the TV up to 15 cm away from the wall.

- The ideal distance to watch TV is 3 times its diagonal screen size. When seated, your eyes should be level with the centre of the screen.

2.4

Power cable

- Insert the power cable into the POWER connector on the back of the TV.

- Make sure the power cable is securely inserted in the connector.

- Make sure that the power plug, in the wall socket, is accessible at all times.

- When you unplug the power cable, always pull the plug, never pull the cable.

- 32Pxx4101 - VESA MIS-F 100x100, M4 (Minimum 10 mm, Maximum 14 mm)

- 40PFx4101, 40PFT4111 - VESA MIS-F 200x200, M4 (Minimum 12 mm, Maximum 16 mm)

- 48PFx4101 - VESA MIS-F 200x200, M6 (Minimum 12 mm, Maximum 16 mm)

Caution

Wall mounting the TV requires special skills and should only be performed by qualified personnel. The TV wall mounting should meet safety standards according to the TV's weight. Also read the safety precautions before positioning the TV.

Although this TV has a very low standby power consumption, unplug the power cable to save energy if you do not use the TV for a long period of time.

2.5

Antenna cable

Insert the antenna plug firmly into the ANTENNA socket at the back of the TV.

You can connect your own antenna or an antenna signal from an antenna distribution system. Use an IEC Coax 75 Ohm RF antenna connector.

Use this antenna connection for DVB-T and DVB-C input signals.

2.6

Satellite dish

- For PHK/PFK models Attach the satellite F-type connector to the satellite

connection SAT at the back of the TV.

Connect devices

3.1

About connections

Copy protection

Connectivity guide

Always connect a device to the TV with the highest quality connection available. Also, use good quality cables to ensure a good transfer of picture and sound.

If you need help to connect several devices to the TV, you can visit the Philips TV connectivity guide. The guide offers information on how to connect and which cables to use.

Go to www.connectivityguide.philips.com

Antenna port

If you have a Set-top box (a digital receiver) or Recorder, connect the antenna cables to run the antenna signal through the Set-top box and/or Recorder first before it enters the TV. In this way, the antenna and the Set-top box can send possible additional channels to the Recorder to record.

HDMI cables support HDCP (High-bandwidth Digital Content Protection). HDCP is a copy protection signal that prevents copying content from a DVD disc or Bluray Disc. Also referred to as DRM (Digital Rights Management).

HDMI ARC

HDMI 1 connection on the TV have HDMI ARC (Audio Return Channel). If the device, typically a Home Theatre System (HTS), also has the HDMI ARC connection, connect it to HDMI 1 on this TV. With the HDMI ARC connection, you do not need to connect the extra audio cable that sends the sound of the TV picture to the HTS. The HDMI ARC connection combines both signals.

In case you prefer to switch off ARC on the HDMI connections, press and select Setup and press OK. Select TV

settings > Sound > Advanced > HDMI 1 - ARC.

HDMI ports

HDMI quality

An HDMI connection has the best picture and sound quality. Use an HDMI cable for TV signal.

For best signal quality transfer, use a High speed HDMI cable and do not use an HDMI cable longer than 5 m.

HDMI CEC - EasyLink

EasyLink

With EasyLink you can operate a connected device with the TV remote control. EasyLink uses HDMI CEC (Consumer Electronics Control) to communicate with the connected devices. Devices must support HDMI CEC and must be connected with an HDMI connection.

EasyLink setup

The TV comes with EasyLink switched on. Make sure that all HDMI CEC settings are properly set up on the connected EasyLink devices. EasyLink might not work with devices from other brands.

HDMI CEC on other brands

The HDMI CEC functionality has different names on different brands. Some examples are: Anynet, Aquos Link, Bravia Theatre Sync, Kuro Link, Simplink and

Viera Link. Not all brands are fully compatible with EasyLink.

Example HDMI CEC branding names are property of their respective owners.

Operate devices

To operate a device connected to HDMI and set up with EasyLink, select the device - or its activity - in the list of TV connections. Press  SOURCES , select a device connected to an HDMI connection and press OK.

Once the device is selected, the TV remote control can control the device. However and  OPTIONS keys and some other TV keys are not forwarded to the device. If the key you need is not on the TV remote control, you can select the key in the Options menu. Press  OPTIONS and select Controls in the menu bar. On the screen, select the device key you need and press OK. Some very specific device keys might not be available in the Controls menu.

Note: Only devices that support EasyLink Remote Control function will respond to the TV remote control.

EasyLink On or Off

DVI to HDMI

If you still own a device that only has a DVI connection, you can connect the device to any of the HDMI connection with a DVI to HDMI adapter.

Use a DVI to HDMI adapter if your device only has a DVI connection. Use one of the HDMI connections and add an Audio L/R cable (mini-jack 3.5mm) to Audio In for sound, on the back of the TV.

Copy protection

DVI and HDMI cables support HDCP (High-bandwidth Digital Content Protection). HDCP is a copy protection signal that prevents copying content from a DVD disc or Blu-ray Disc. Also referred to as DRM (Digital Rights Management).

Audio Out - Optical

Audio Out - Optical is a high quality sound connection. This optical connection can carry 5.1 audio channels. If your device, typically a Home Theatre System (HTS), has no HDMI ARC connection, you can use this connection with the Audio In Optical connection on the HTS. The Audio Out Optical connection sends the sound from the TV to the HTS.

The TV comes with all EasyLink settings switched on. You can switch off any EasyLink setting independently.

To switch off EasyLink completely . . .

1. Press and select Setup and press OK.

2. Select TV settings > General settings > EasyLink.

3. Select EasyLink.

4. Select Off and press OK.

5. Press , repeatedly if necessary, to close the menu.

EasyLink Remote Control EasyLink Remote Control

If you want devices to communicate but you don't want to operate them with the TV remote control, you can switch off EasyLink remote control separately. You can control multiple HDMI-CEC compliant devices with your TV remote control.

In the EasyLink settings menu, select EasyLink Remote Control and select Off.

You can set the type of the audio out signal to fit the audio capabilities of your Home Theatre System.

If the sound does not match the video on screen, you can adjust the audio to video synchronization.

Scart

SCART is a good quality connection. The SCART connection can be used for CVBS and RGB video signals but cannot be used for High Definition (HD) TV signals. The SCART connection combines video and audio signals.

Use the SCART adapter cable to connect your device.

It may take a few minutes before the CAM is activated. Removing the CAM will deactivate the broadcast service on TV. If a CAM is inserted and subscription fees are paid, (connection methods can differ), you can watch the TV broadcast. The inserted CAM is exclusively for your TV.

3.3

Set-top box - STB

3.2

Common interface - CAM

CI+

This TV is ready for the CI+ Conditional Access. With CI+ you can watch premium HD programmes,

like movies and sports, offered by digital TV broadcasters in your region. These programmes are scrambled by the TV broadcaster and descrambled with a prepaid CI+ module. Digital TV broadcasters provide this CI+ module (Conditional Access Module - CAM) when you subscribe to their premium programmes. These programmes have a high level of copy protection.

Contact a digital TV broadcaster for more information on terms and conditions.

Use 2 antenna cables to connect the antenna to the Set-top box (a digital receiver) and the TV.

Next to the antenna connections, add an HDMI cable to connect the Set-top box to the TV.

Auto switch off Switch off this automatic timer, if you only use the

remote control of the Set-top box. Do this to prevent the TV from switching off automatically after a 4 hour period without a key press on the remote control of the TV.

CAM

Insert a CAM module

Switch off the TV before inserting a CAM. Look on the CAM for the correct method of insertion. Incorrect insertion can damage the CAM and TV.

Use the Common Interface slot on the TV to insert the CAM card. With the front of the card facing to you, gently insert the CAM as far as it will go. Leave the card in the slot permanently.

To switch off the Switch off timer, press and select Setup and press OK. Select TV settings > General settings > Switch off timer and set the slider bar to Off.

3.4

Satellite receiver

Connect the dish antenna cable to the Satellite receiver.

Next to the antenna connection, add an HDMI cable to connect the device to the TV.

Connect with HDMI

Use an HDMI cable to connect a Home Theatre System (HTS) to the TV. You can connect a Philips Soundbar or an HTS with a built-in disc player.

If the Home Theatre System has no HDMI ARC connection, add an optical audio cable (Toslink) to send the sound of the TV picture to the Home Theatre System.

Auto switch off

Switch off this automatic timer, if you only use the remote control of the Set-top box. Do this to prevent the TV from switching off automatically after a 4 hour period without a key press on the remote control of the TV.

To switch off the Switch off timer, press and select Setup and press OK. Select TV settings > General settings > Switch off timer and set the slider bar to Off.

3.5

Home Theatre System - HTS

Connect with HDMI ARC

Use an HDMI cable to connect a Home Theatre System (HTS) to the TV. You can connect a Philips Soundbar or an HTS with a built-in disc player.

HDMI ARC

Audio to video synchronisation (sync)

If the sound does not match the video on screen, you can set a delay on most Home Theatre Systems with a disc player to match the sound with the video.

Audio Out settings

Audio Out delay

With a Home Theatre System (HTS) connected to the TV, the picture on TV and the sound from the HTS should be synchronised.

Automatic audio to video sync

With recent Philips Home Theatre Systems, the audio to video sync is automatically synchronised and always correct.

Audio sync delay

For some Home Theatre Systems you might need to adjust the audio sync delay to synchronise the audio to video. On the HTS, increase the delay value until there is a match between picture and sound. A delay value of 180ms may be required. Read the user manual of the HTS. With a delay value set up on the HTS, you need to switch off Audio Out delay on the TV.

To switch off the Audio Out delay . . .

1. Press and select Setup and press OK.

2. Select TV settings > Sound > Advanced > Audio out delay.

3. Select Off and press OK.

4. Press , repeatedly if necessary, to close the menu.

Audio to video synchronisation (sync)

If the sound does not match the video on screen, you can set a delay on most Home Theatre Systems with a disc player to match the sound with the video.

Audio Out offset

If you cannot set a delay on the Home Theatre System, you can set the TV to sync the sound. You can set an offset that compensates the time necessary for the Home Theatre System to process the sound of the TV picture. You can set the value in steps of 1ms. Maximum setting is 12ms. The Audio out delay setting should be switched on.

To synchronise the sound on the TV . . .

1. Press and select Setup and press OK.

2. Select TV settings > Sound > Advanced > Audio out offset.

3. Use the slider bar to set the sound offset and press OK.

4. Press , repeatedly if necessary, to close the menu.

Audio Out format

If you have a Home Theatre System (HTS) with multichannel sound processing capabilities like Dolby Digital, DTS® or similar, set the Audio out format to Multichannel. With Multichannel, the TV can send the compressed multichannel sound signal from a TV channel or connected player to the Home Theatre System. If you have a Home Theatre System without multichannel sound processing, select Stereo.

To set the Audio Out format . . .

1. Press and select Setup and press OK.

2. Select TV settings > Sound > Advanced > Audio out format.

3. Select Multichannel or Stereo.

4. Press , repeatedly if necessary, to close the menu.

No sound

If you cannot hear the sound from the TV on your Home Theatre System, check the following . . .

- Check if you connected the HDMI cable to a HDMI 1 connection on the Home Theatre System.

- Check if the HDMI ARC setting on the TV is switched On. Go to > Setup > TV settings > Sound > Advanced > HDMI 1 -ARC.

3.6

Blu-ray Disc player

Use a High speed HDMI cable to connect the Blu-ray Disc player to the TV.

Audio Out levelling

Use the Audio Out leveling setting to level the volume (loudness) of the TV and the Home Theatre System when you switch over from one to another. Volume differences can be caused by differences in sound processing.

To level the difference in volume . . .

1. Press and select Setup and press OK.

2. Select TV

settings > Sound > Advanced > Audio out leveling.

3. If the volume difference is large, select More. If the volume difference is small, select Less. Press , repeatedly if necessary, to close the menu.

Audio Out leveling affects both the Audio Out Optical and HDMI ARC sound signals.

Problems with HTS sound

Sound with loud noise

If you watch a video from a plugged in USB flash drive or connected computer, the sound from your Home Theatre System might be distorted.

1. Press and select Setup and press OK.

2. Select TV settings > Sound > Advanced > Audio out format.

If the Blu-ray Disc player has EasyLink HDMI CEC, you can operate the player with the TV remote control.

3.7

DVD player

Use an HDMI cable to connect the DVD player to the TV.

If the DVD player is connected with HDMI and has EasyLink CEC, you can operate the player with the TV remote control.

3.8

Game console

HDMI

For best quality, connect the game console with an High speed HDMI cable to the TV.

Best Setting

you can check if you can record digital TV channels in your country. Press  TV GUIDE on the remote control. If there is a Record button on the TV guide page, you can record.

Installation

Before you can pause or record a broadcast, you must connect and format a USB Hard Drive.

1. Connect the USB Hard Drive to one of the USB connections on the TV. Do not connect another USB device to the other USB ports when formatting.

2. Switch on the USB Hard Drive and the TV.

3. When the TV is tuned to a digital TV channel, press (Pause). Trying to pause will start the formatting.



Follow the instructions on screen. When the USB Hard Drive is formatted, leave it

connected permanently.

Before you start playing a game from a connected game console, we advice you to set the TV in the ideal setting Game.

To set the TV to the ideal setting…

1. Press and select Setup and press OK.

2. Select TV settings > Picture > Advanced > Activity style.

3. Select Game, Computer or TV. The setting TV returns to the picture settings for watching TV.

4. Press , repeatedly if necessary, to close the menu.

3.9

USB Hard Drive

What you need

If you connect a USB Hard Drive, you can pause or record a TV broadcast. The TV broadcast must be a digital broadcast (DVB broadcast or similar).

To pause

To pause a broadcast, you need a USB 2.0 compatible Hard Drive with a minimum of 32GB disc space.

To record

To pause and record a broadcast, you need a minimum of 250GB disc space.

TV guide

Before you decide to buy a USB Hard Drive to record,

Warning

The USB Hard Drive is formatted exclusively for this TV, you cannot use the stored recordings on another TV or PC. Do not copy or change recording files on the USB Hard Drive with any PC application. This will corrupt your recordings. When you format another USB Hard Drive, the content on the former will be lost. A USB Hard Drive installed on your TV will need reformatting for use with a computer.

Formatting

Before you can pause or record a broadcast, you must connect and format a USB Hard Drive. Formatting removes all files from the USB Hard Drive.

Warning

To format a USB Hard Drive…

1. Connect the USB Hard Drive to one of

the USB connections on the TV. Do not connect another USB device to the other USB ports when formatting.

2. Switch on the USB Hard Drive and the TV.

3. When the TV is tuned to a digital TV channel,

press  (Pause). Trying to pause will start the formatting. Follow the instructions on screen.

When the USB Hard Drive is formatted, leave it connected permanently.

3.12

Computer

Connect

3.10

USB flash drive

You can view photos or play your music and videos from a connected USB flash drive.

Insert a USB flash drive in one of the USB connections on the TV while the TV is switched on.

The TV detects the flash drive and opens a list showing its content. If the contents list does not appear automatically, press  SOURCES , select USB and press OK.

To stop watching the USB flash drive content, press

EXIT or select another activity.



To disconnect the USB flash drive, you can pull out the flash drive anytime.

You can connect your computer to the TV and use the TV as a PC monitor.

With HDMI

Use an HDMI cable to connect the computer to the TV.

With DVI to HDMI

Alternatively, you can use a DVI to HDMI adapter to connect the PC to HDMI and an audio L/R cable (minijack 3.5mm) to AUDIO IN L/R on the back of the TV.

3.11

Camcorder - HDMI

For best quality, use an HDMI cable to connect the camcorder to the TV.

Best Setting

Ideal monitor setting

If your computer is added as a Computer type of device in the Source menu (the list of connections), the TV is set to the ideal Computer setting automatically.

If you use your computer to watch movies or use it to play games, you might want to set the TV back to the ideal TV watching or gaming setting.

To set the TV to the ideal setting manually . . .

1. Press and select Setup and press OK.

2. Select TV

settings > Picture > Advanced > Activity style.

3. Select Game, Computer or TV. The

setting TV returns to the picture settings for watching TV.

4. Press , repeatedly if necessary, to close the

menu. Remember to set the Game or computer setting back

to Computer when you stop playing the game.

3.13

Headphones

Side

You can connect a set of headphones to  connection on the TV. The connection is a minijack 3.5mm. You can adjust the volume of the headphones separately.

To adjust the volume . . .

1. Press and select Setup and press OK.

2. Select TV settings > Sound > Headphone volume and press OK.

3. Press  (up) or  (down) to adjust the volume.

4. Press , repeatedly if necessay, to close the menu.

key.

Switch on

4.1

On, Standby or Off

For 4100, 4200, 4101, 4111, 4201 series

Before you switch on the TV, make sure you plugged in the mains power in the POWER connector on the back of the TV.

To put the TV in Standby when the indicator light is off, press the small joystick key on the back of the TV. The indicator will light up.

With the TV in standby, press  on the remote control to switch the TV on.

Switch to standby

To switch the TV to Standby, press  on the remote control.

Switch Off

To switch the TV Off, press the joystick key. The indicator light goes off. The TV is still connected to the mains power but consumes very little energy.

To switch off the TV completely, disconnect the power plug. When disconnecting the power plug, always pull the power plug, never the cord. Ensure that you have full access to the power plug, power cord and outlet socket at all times.

4.3

Sleep timer

With the sleep timer, you can set the TV to switch to standby automatically after a preset time.

To set the sleep timer . . .

1. Press and select Setup and press OK.

2. Select TV settings > General settings > Sleep

timer. With the slider bar you can set the time to up to 180 minutes in increments of 5 minutes. If set to 0 minutes, the sleep timer is switched off.You can always switch off your TV earlier or reset the time during the countdown.

3. Press , repeatedly if necessary, to close the

menu.

4.4

Switch Off Timer

If the TV receives a TV signal but you don't press a key on the remote control during a 4 hour period, the TV switches off automatically to save energy. Also, if the TV does not receive a TV signal nor a remote control command for 10 minutes, the TV switches off automatically.

If you use the TV as a monitor or use a digital receiver to watch TV (a Set-Top Box - STB) and you do not use the remote control of the TV, you should deactivate this automatic switch off.

4.2

Keys on TV (For 4100, 4200, 4101, 4111, 4201, 6300, 630) series

If you lost the remote control or its batteries are empty, you can still do some basic TV operations.

To open the basic menu…

1. With the TV switched on, press the joystick key on the back of the TV to bring up the basic menu.

2. Press left or right to select  Volume,  Channel or  Sources.

3. Press up or down to adjust the volume or tune to the next or previous channel. Press up or down to go through the list of sources, including the tuner selection.

4. The menu will disappear automatically. To switch the TV off, select  and press the joystick

To deactivate the Switch Off Timer …

1. Press and select Setup and press OK.

2. Select TV settings > General settings > Switch

off timer.

3. Press  (up) or  (down) to adjust the

value. The value 0 deactivates the automatic switch off.

4. Press , repeatedly if necessary, to close the

menu.

Remote control

5.1

Key overview (For 4000, 4100, 4200, 4101, 4111, 4201,

1.  SOURCES

To open or close the Sources menu - the list of connected devices.

2. Colour keys

The buttons function follow the on-screen instructions.

3.  INFO

To open or close programme infomation.

5210 series)

Top

1.  Standby / On

To switch the TV on or back to Standby.

2. Playback keys

- Play , to playback

- Pause , to pause playback

- Stop , to stop playback

- Rewind , to rewind

- Fast forward , to go fast forward

- Record , to record now

4.  BACK

To switch back to the previous channel you selected. To close a menu without changing a setting.

5. HOME

To open or close the home menu.

6.  EXIT

To switch back to watching TV.

7.  OPTIONS

To open or close the Options menu.

8. OK key

To confirm a selection or setting.

9. Arrow / navigation keys

To navigate up, down, left or right.

10.  LIST

To open or close the channel list.

Bottom

3.  TV GUIDE

To open or close the TV Guide.

4.  SETUP To open the Settings menu.

5.  FORMAT To open or close the Picture format menu.

Middle

1.  Volume

To adjust the volume level.

2. Number keys and text keypad

To select a TV channel directly or to enter text.

3. SUBTITLE

To switch subtitles on, off or Automatic.

4.  Channel

To switch to the next or previous channel in the channel list. To open the next or previous page in Text/Teletext. To start the next or previous chapter on a disc.

5.  Mute

To mute the sound or to restore it.

6. TEXT To open or close Text / Teletext.

5.2

IR sensor

The TV can receive commands from a remote control that uses IR (infrared) to send commands. If you use such a remote control, always make sure you point the remote control at the infrared sensor on the front of the TV.

5.3

Batteries

1. Slide the battery door in the direction shown by the arrow.

2. Replace the old batteries with 2 type AAA-LR03-1.5V batteries. Make sure the + and the - ends of the batteries line up correctly.

3. Reposition the battery door.

4. Slide it back until it clicks. Remove the batteries if you are not using the remote

control for a long time. Safely dispose of your old batteries according to the end of use directions.

5.4

Cleaning

Your remote control is treated with a scratch-resistant coating.

To clean the remote control, use a soft damp cloth. Never use substances such as alcohol, chemicals or household cleaners on the remote control.

select All, Favourites, Radio, and New channels.

TV channels

6.1

Channel Lists

About channel lists

After a channel installation, all channels appear on the channel list. Channels are shown with their name and logo if this information is available.

With a channel list selected, press the arrows  (up) or  (down) to select a channel, then press OK to watch the selected channel. You only tune to the channels in that list when using   or   keys.

Channel icons

After an Automatic Channel Update of the channel list, newly found channels are marked with a  (star). If you lock a channel, it will be marked with a  (lock).

Radio stations

If digital broadcasting is available, digital radio stations are installed during installation. Switch to a radio channel just like you switch to a TV channel. A Cable (DVB-C) channel installation usually places radio stations from channel number 1001 onwards.

This TV can receive digital television standard DVB . TV may not work properly with some operators of digital television , non-compliance with requirements of the standard in full.

6.2

Watching TV channels

Watching channels

Tune to a channel

To watch TV channels, press . The TV tunes to the TV channel you last watched.

Switch channels

- To switch channels, press   or  .

- If you know the channel number, type in the

number with the number keys. Press OK after you entered the number to switch immediately.

Previous channel

- To switch back to the previously tuned channel,

press .

Channel list

While watching a TV channel, press  LIST to open the channel lists.

The channel list can have several pages with channels. To view the next or previous page, press  + or  . To close the channel lists without switching channel, press  LIST again.

Radio channels

If digital broadcasting is available, digital radio station are installed during installation. Switch to a radio channel just like you switch to a TV channel.

Open a channel list

To open the current channel list…

1. Press , to switch to TV.

2. Press  LIST to open the current channel list.

3. Press  LIST again to close the channel list.

Filter a channel list

You can filter a list with all channels. You can set the channel list to show only TV channels or only Radio stations.

To set a filter on a list with all channels…

1. While watching a TV channel, press open the channel list.

2. Press  OPTIONS to open Option menu.

3. Select List, then you can



LIST to

Lock a channel

Lock and unlock a channel

To prevent children from watching a channel or a programme, you can lock channels or lock age rated programmes.

You can lock a channel to prevent children from watching it. To watch a locked channel you need to enter the Child lock code. You cannot lock programmes from connected devices.

To lock a channel . . .

1. While watching a TV channel, press  LIST to

open the Channel list.

2. In any list, select the channel you want to lock.

3. Press  OPTIONS and select Lock channel. In a

channel list, a locked channel is marked with a lock .

+ 39 hidden pages

Philips 32PHH4101-88 Instruction manual

Contents