Philips 28PW9309/05 User Manual

tv
Information for users in the UK
(Not applicable outside the UK)
Positioning the TV
For the best results, choose a position where light does not fall directly on the screen, and at some distance away from radiators or other sources of heat. Leave a space of at least 5 cm all around the TV for ventilation, making sure that curtains, cupboards etc. cannot obstruct the air flow through the ventilation apertures. The TV is intended for use in a domestic environment only and should never be operated or stored in excessively hot or humid atmospheres.
General Points
Please take note of the section 'Tips' at the end of this booklet.
Interference
The Department of Trade and Industry operates a Radio Interference Investigation Service to help TV license holders improve reception of BBC and IBA programmes where they are being spoilt by interference. If your dealer cannot help, ask at a main Post Office for the booklet "How to improve Television and Radio Reception".
Mains connection
Before connecting the TV to the mains, check that the mains supply voltage corresponds to the voltage printed on the type plate on the rear panel of the TV. If the mains voltage is different, consult your dealer.
Important
This apparatus is fitted with an approved moulded 13 Amp plug. To change a fuse in this type of plug proceed as follows :
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
In order to maintain conformity to the EMC directive, the mains plug on this product must not be removed.
Connecting the aerial
The aerial should be connected to the socket marked x at the back of the set. An inferior aerial is likely to result in a poor, perhaps unstable picture with ghost images and lack of contrast. Make­shift or set-top aerials are unlikely to give adequate results. Your dealer will know from experience the most suitable type for your locality. Should you wish to use the set in conjunction with other equipment, which connects to the aerial socket such as TV games, or a video camera, it is recommended that you consult your dealer on the best method of connection.
Stand (if provided)
Use only the stand provided with the set, making sure that the fixings are properly tightened.A diagram showing how to assemble the stand is packed with the stand. Never use a make-shift stand, or legs fixed with woodscrews.
Contents
Help?
If this instruction manual does not give an answer or if ‘Tips’ do not solve your TV problem, you can call your Local Philips Customer or Service Centre. See the supplied World-wide guarantee booklet. Please, have the Model and Product number which you can find at the back of your television set or on the packaging, ready, before calling the Philips helpline.
Model: 28/32PW9309/05
Product No: ..............................................
Due to continuous product improvements this manual is subject to change without notice.
R End of life directives
Philips is paying a lot of attention to producing environmentally-friendly in green focal areas.Your new TV contains materials which can be recycled and reused. At the end of its life specialised companies can dismantle the discarded TV to concentrate the reusable materials and to minimise the amount of materials to be disposed of. Please ensure you dispose of your old TV according to local regulations.
Installation
Preparation ........................................................................................ 2
Keys on top of the TV .................................................................... 2
Your remote control ................................................................... 3-4
To use the menus .............................................................................. 5
Select the menu language and country ....................................... 5
Store TV channels ............................................................................ 6
Automatic installation ..............................................................6
Manual installation .................................................................... 6
Give name .................................................................................. 6
Reshuffle the programme list.................................................. 7
Select favourite TV channels .................................................. 7
TV setup ............................................................................................. 7
General ....................................................................................... 7
Source .......................................................................................... 8
Decoder ...................................................................................... 8
Demo .................................................................................................. 9
Operation
TV menu
Picture menu ........................................................................ 9-10
Sound menu ............................................................................. 10
Features menu......................................................................... 11
Teletext guide ................................................................................. 12
Teletext ...................................................................................... 13-14
Connect peripheral equipment
Connecting and selecting equipment ..................................15-16
Audio- and video equipment keys ............................................. 17
Tips .................................................................................................. 18
English
EasyLink features are based on the “one touch operation” approach. This means that a sequence of actions are executed at the same time in both the television and the video cassette recorder, provided both are fitted with the EasyLink function and connected with the eurocable supplied with your video recorder.
1
Preparation
MENU PROGRAMVOLUME
& Place the TV on a solid surface.
! 28PW9309: 37 kg; 32PW9309: 56 kg !
min.
1m
For ventilation, leave at least 5 cm free all around the TV. Do not place the TV on a carpet.To prevent any unsafe situations, do not place any objects on top of the TV. Avoid heat, direct sunlight and exposure to rain or water.
é Insert the aerial plug firmly into the aerial
socket x at the back of the TV. For best picture quality use the suppressor-aerial cable supplied.
Insert the mains plug of the TV in the wall
socket having a mains voltage of 220V-240V.
Keys on top of the TV
Remote control: Insert the 2 batteries
supplied (Type R6-1,5V).
The batteries supplied do not contain the heavy metals mercury and cadmium. Please check on how to dispose of exhausted batteries according to local regulations.
( Switch the TV on :Press the power switch A
on the front of your TV. A blue indicator on the front of the TV lights up and the screen comes on. If the TV is in standby mode (red indicator), press the
-P+
keys or the red B key on the remote control.
TV
Setup
Demo
Install
Exit
2
2
Picture Sound Features
Should your remote be lost or broken you can still change some of the basic settings with the keys on top of your TV.
Press:
• the
VOLUME - or + key to adjust the volume;
• the - PROGRAM + keys to select the TV channels or sources.
Press the
MENU key to summon the main menu
without the remote control. Use:
• the
VOLUME - and + key and the PROGRAM -
and PROGRAM + key to select menu items in the directions as shown;
• the
MENU key to confirm your selection.
Note: When activated via the
Exit lets you dismiss the menu.
Navigate to
Exit and press the MENU key.
MENU key on top of the TV, only
Use of the remote control RC4337
b
¬
+
-
V
+
-
P
v
i
0
VCR DVD TV SAT AMP
S
MENU
123
456
789
0
‡π
x
®
®
®
®
q
b
h
Q
SMART SMART
aM
ACTIVE
CONTROL
B
OK
SELECT
Ò
U
®
æ
º
Note: For most keys pressing a key once will activate the function. Pressing a second time will de-activate it. When a key enables multiple options, a small list will be shown. Press repeatedly to select the next item in the list. The list will be removed automatically after 4 seconds or press
VCR DVD TV SAT AMP
Audio- and Video equipment keys (p. 17)
OK to remove immediately.
B Standby
Press to switch the TV on or off. When switched off, a red indicator lights up.
vSelect peripherals (p. 16)
®Ò‡π†
Audio- and Video equipment keys (p. 17)
UTime display
The time is displayed on the screen.
æTeletext guide on/off p. 12
OK Press this key
• to activate your choice, when in
• to display the programme list.
S Freeze To freeze the picture.
V To adjust the volume.
¬ Interrupt the sound or restore it.
iOn Screen information
b key to show
Press the Teletext guide on the right half of the screen.
the menus.
Press to display information about the selected TV channel and programme.
Menu/Remote control info
When a menu is on screen, press
i to display info on the
selected menu item. For information on the remote control functions, while the menu info is displayed, press any key on the remote control. The normal function of the key is
Ma Smart keys
not executed.
To select predefined picture and sound settings. Personel refers to the personal preference settings selected in the sound and picture menu.
xPixel Plus demo on/off
In the right part Pixel Plus and Digital Natural Motion are switched on.
bTeletext on/off p. 13
Press the
b key to show
teletext on the right half of the screen.
MENU Main menu on/off see p. 5
PProgramme selection
To browse through the TV channels and sources stored in the favourite list.
0/9 Digit keys
To select a TV channel. For a two digit programme number, enter the second digit within 2 seconds.To switch immediately to a selected one digit TV channel, keep the digit key pressed a bit longer.
QSurround mode
Incredible surround
With stereo transmission, and when Incredible surround is selected, it seems as though the loudspeakers are spread further apart from one another.
Virtual Dolby surround
Optimal with Dolby surround signals. Enables you to experience the effect of Dolby surround Pro Logic, reproducing a rear sound effect. See Sound menu, 3D effect, p. 10.
Note:You can make the same selection in the Sound menu, surround mode, p. 10.
33
b
¬
+
-
V
+
-
P
v
i
0
VCR DVD TV SAT AMP
S
MENU
123
456
789
0
x
®
®
®
®
q
b
h
Q
SMART SMART
aM
ACTIVE
CONTROL
B
OK
SELECT
æ
‡π
Ò
U
®
º
0 Smart surf
With this key you can easily switch between 2 up to 9 different TV channels or sources. See General, Smart surf, p. 7. Press the
OK key or wait for the time out to dismiss the Smart surf
display.
b Dual screen
Press the b or æ key.
&
Press the
b key to show Teletext or Teletext Guide on the right of the
screen.
é • Picture/Teletext Guide:
-Press the cursor left/right to select a TV channel.
-Press the cursor down and to the left to move the puck to the blue ball in the left screen.
-Press
+P- to select another TV channel.
• Picture/Teletext: See Active screen selection, p. 13.
Press the b key to switch off dual screen.
h Active control see p. 10
q Picture format
Press this key repeatedly or press the cursor up/down to select another picture format:Auto format, Super zoom, 4:3, Movie Expand 14:9, Movie Expand 16:9, Subtitle zoom or Wide screen.
Auto format Super zoom 4:3 Movie Expand 14:9
Movie Expand 16:9 Subtitle zoom Wide screen
Auto format makes the picture fill the screen as much as possible. In case of subtitles in the bottom black bar,Auto format makes the subtitles visible. If subtitles are only partly visible, press cursor up. In case of a broadcaster logo in the corner of the top black bar, the logo disappears from the screen.
Super zoom removes the black bars on the sides of 4:3 programs with minimal distortion.
When in Movie Expand 14:9, 16:9, Super zoom or Subtitle zoom picture format, you can make subtitles visible with the cursor up/down.
4
To use the menus
b
¬
+
V
+
P
v
VCR DVD TV SAT AMP
S
MENU
x
®
®
®
®
B
OK
SELECT
æ
‡π
Ò
U
®
º
OK key to
activate
cursor to select adjustments
return or switch main menu on/off
Press the i key to get information about the selected menu item.
& Press the MENU key on the remote control to summon the
main menu.At any moment you can exit the menu by pressing the
MENU key again.
Note: If you have connected equipment with Cinema Link, more menu items are present.
Picture Sound Features
TV
Setup
Demo
Install
é Use the cursor in the up/down direction to select the TV,
Setup, Demo or Install menu.
Use the cursor left/right to select
Picture, Sound or
Features.
Note: Sometimes not all the menu items are visible on the screen (indicated by a cluster of blue balls). Use the cursor down or right to reveal all items.
Use the cursor in the left/right direction to select the menu
item.
Use the cursor up/down again to select the control you
want to select or to adjust.
Note: Items temporary not available or not relevant are displayed in a light grey colour and cannot be selected.
Installation
The installation menu contains the following items:
Language Country Automatic Manual Give name Reshuffle Favourite
install install programmes
Install
EasyLink
If your video recorder has an EasyLink function, during installation, the language, country and available channels are automatically transmitted to the video recorder.
Select the menu language and country
Install
Install
Language
English Deutsch Français
Country
Austria
Belgium
Croatia
& Press the MENU key on the remote control. é Use the cursor down to select Install. “ Use the cursor right to select Language.
Follow the instructions on screen.
Use the cursor up/down to select your preferred language
and press the
( Use the cursor right to select Country.
§ Select the country where you are now located and press
the
OK key.
Select
è Proceed with the Install menu.
OK key to confirm your selection.
Other when none of the countries applies.
5
Store TV channels
After language and country are set correctly, you can now search for and store the TV channels in two different ways: using Automatic Installation or Manual Installation (tuning-in channel by channel). Select your choice with the cursor right.
Automatic installation
Install
& Select Automatic install in the Install menu.
Note: All channels must be unlocked in order to autoprogram. If requested, enter your code to unlock all channels. (See TV, Features menu, Childlock, p. 11.)
é Press the cursor down.The autoprogramming
option label
Press the cursor right.
Manual installation
Install
Automatic install
Install Start
Start appears.
Manual install
Selection mode System Programme Search Fine tune Store
Searching for and storing TV channels is done channel by channel. You must go through every step of the Manual Installation menu.
& Select Manual install in the Install menu. é Press the cursor down.
Follow the instructions on screen.
Note: Search or direct selection of a TV channel.
If you know the frequency, the C- or S-channel number, enter the 3 or 2 digits of the frequency or the channel number directly with the digit keys 0 to 9 (e.g. 048). Press the cursor down to proceed.
The message Searching appears and the
progress of autoprogramming is displayed.
If a cable system or a TV channel which broadcasts ACI (Automatic Channel Installation) is detected, a programme list appears.Without ACI broadcast, the channels are numbered according your language and country selection.You can use Reshuffle to renumber them. See p. 7.
It is possible that the cable company or the TV channel displays a broadcast selection menu. Layout and items are defined by the cable company or the TV channel. Make your choice with the cursor and press the
OK key.
Repeat to search for another TV channel.
Give name
Install
It is possible to change the name stored in the memory or to assign a name to a TV channel for which a name has not yet been entered.A name with up to 5 letters or numbers can be given to the programme numbers 0 to 99.
& Select Give Name in the Install menu and
press the cursor down.
6
Give name
VCR1 BBC1 BBC2
CNN
TVE
.....
® Space ® Delete
ABCDEFG 123 HIJKLMN 456 OPQRSTU 789 VWXYZ 0
® Shift ® Special
é Select the programme number.
Note: keep the cursor up/down pressed to scroll through the programme list quickly.
Press the cursor right.
A keyboard appears on the screen. Press the cursor right to enter the keyboard. Press the cursor up/down, left/right to select the first character and press
OK. Repeat for
every character you want to enter. Select
Space to enter a space; Delete to erase
the highlighted character in the name entered;
Shift to display upper- or lowercase characters
on the keyboard; characters on the keyboard. Press
Special to display special
OK to
confirm.
Press the cursor left repeatedly when you have
finished the name giving.
( Select another programme number and repeat
steps
to ‘.
Loading...
+ 22 hidden pages