Philips 27PC4326-37 User Manual
ANT.
AUDIO OUTAUDIO OUT
COAXIALCOAXIAL
IN
OUT
OR
3
CABLE BOX
CABLE TV SIGNAL
RF COAXIAL
CABLE
ANT.
4
ANT.
ANTENNA or
CABLE TV SIGNAL
2
1
Disconnect all equipment from the power outlets. Connect the equipment to the power outlets only after you
have finished hooking up everything. Never make or change connections with equipment connected to the power outlet.
2
If you do not have a Cable Box, simply connect your Antenna or Cable TV signal directly to the ANT. (enna)
jack on the rear of the TV/VCR/DVD.
3
If you do have a Cable Box or Satellite Receiver, first connect the Cable TV or Satellite signal to the IN jack
on the Cable Box or Satellite Receiver. Then, use an RF coaxial cable (not supplied) to connect the OUT
jack of the Cable Box or Satellite Receiver to the ANT. (enna) jack on the TV/VCR/DVD. To view any channel,
set the TV/VCR/DVD to the output channel of the Cable Box or Satellite Receiver (channel 3 or 4).Then, select channels at
the Cable Box or Satellite Receiver.
4
When all connections are complete, plug the power cord of the TV/VCR/DVD into an active power
outlet.
5
Press STANDBY-ONy on the TV/VCR/DVD or its remote to turn on the unit.
There are many ways to connect your new TV/VCR/DVD to your other equipment. This Quick Start Guide
shows the easiest, most common connections for the TV/VCR/DVD.
27PC4326
Printed in Malaysia
8239 300 47441
1EMN21841
T3221UB*****
T3221UB_QSG_EN 5/8/06 7:18 PM Page 1
123
456
STANDBY-ON
OPEN/CLOSE
MODE
SELECT
DISPLAY
CH. VOL.
MUTE
MENU
PICTURE
/SLEEP
Quick Start Guide (cont’d)
Quick Start Guide (cont’d)
Detailed playback features and additional functions are described in the
accompanying user manual.
Watching TV
1
Press STANDBY-ONy to turn on the TV/VCR/DVD. The red VCR/TV light
will appear.
2
This unit memorizes TV channels when you connect an Antenna or Cable TV signal
as described in this Quick Start Guide.
To watch TV, use CH. ▲/▼ to select memorized channels. If a channel is skipped,
use the Number buttons to select it.To update your channels later, refer to the user
manual.
3
Press VOL.X/Yto adjust the volume.
Playing a Videotape
1
With the unit on, press SELECT to put the unit in TV/VCR mode. The red
VCR/TV light will appear.
2
Insert a videotape in the cassette compartment. If playback does not start
automatically, press PLAY B.
3
Press STOP C to stop playback.
Playing a DVD
1
With the unit on, press SELECT repeatedly to put the TV/VCR/DVD in
DVD mode. The green DVD light will appear on the front of the TV/VCR/DVD.
2
Press OPEN/CLOSE A to open the disc tray.
3
Place a disc into the tray, with the label facing up and the shiny side facing
down.
Playable Discs
The TV/VCR/DVD will play the following discs.
Windows Media is a trademark of Microsoft Corporation.
DVDs must have a Region Code of ALL regions or Region 1.
DVDs must be recorded in the NTSC Color System.
1
2
3
2
1
3
4
Press PLAY B. The tray will close and playback will begin. If playback does
not start automatically, press PLAY B again.
If a DVD menu appears instead, use KLs B, ENTER or Number buttons to
choose features or start playing from the menu.
5
Press STOP C to stop playback.
is a trademark of DVD Format/Logo Licensing Corporation.
4
2
1
5
T3221UB_QSG_EN 4/6/06 1:09 PM Page 2
VOLUME 20
HG
PLAY
STOP
SLOW PAUSE
RETURN
DISC SET-UP
MENU
PICTURE
/SLEEP
SELECT
MODE
STANDBY-ON
123
456
7
CLEAR
ENTER
CH. VOL.
DISPLAY
8
0
REC MODE REC
TITLE
MUTE
OPEN/CLOSE
9
+100
+10
ALL
1
HG
PLAY
STOP
SLOW PAUSE
RETURN
DISC SET-UP
MENU
PICTURE
/SLEEP
SELECT
MODE
ENTER
CH. VOL.
DISPLAY
TITLE
MUTE
Loading...