Page 1
22PFL4506/V7
26PFL4306/V7
EN
User ma
ual
n
Page 2
Contents
1 Notice
2 Important
3 Your TV
4 Remote Control Functions
5 Use your TV
6 FAQ
7 Other Information
8 Product
information
2
3
5
7
8
12
13
14
EN 1
Page 3
1 Notice
Pixel characteristics
This LCD/LED product has a high number of
colour pixels. Although it has effective pixels of
99.999% or more, black dots or bright points of
light (red, green or blue) may appear constantly
on the screen. This is a structural property of
the display (within common industry standards)
and is not a malfunction.
Warranty
No components are user serviceable. Do not
open or remove covers to the inside of the
product. Repairs may only be done by Philips
Service Centres and official repair shops. Failure
to do so shall void any warranty, stated or
implied.
Any operation expressly prohibited in
this manual, any adjustments, or assembly
procedures not recommended or authorised in
this manual, shall void the warranty.
2 EN
Page 4
2 Important
Read and understand all instructions before you
use your TV. If damage is caused by failure to
follow instructions, the warranty does not apply.
Safety
Risk of electric shock or fire !
Never expose the TV to rain or water.
Never place liquid containers, such as
vases, near the TV. If liquids are spilt on
or into the TV, disconnect the TV from
the power outlet immediately. Contact
Philips Consumer Care to have the TV
checked before use.
Never place the TV, remote control or
batteries near naked flames or other heat
sources, including direct sunlight.
To prevent the spread of fire, keep
candles or other flames away from the
TV, remote control and batteries at all
times.
Never insert objects into the ventilation
slots or other openings on the TV.
When the TV is swiveled ensure that
no strain is exerted on the power cord.
Strain on the power cord can loosen
connections and cause arcing.
Risk of electric shock or fire !
Never expose the remote control or
batteries to rain, water or excessive heat.
Avoid force coming on to power plugs.
Loose power plugs can cause arcing or
fire.
Risk of injury or damage to the TV!
Two people are required to lift and carry
a TV that weights more than 25 kg.
Risk of swallowing batteries!
When stand mounting the TV, use only
the supplied stand. Secure the stand to
the TV tightly. Place the TV on a
surface that can support the combined
weight of the TV and the stand.
When wall mounting the TV, use only a
wall mount that can support the weight of
the TV. Secure the wall mount to a wall
that can support the combined weight of
the TV and wall mount.
bears no responsibility
mounting that result in
damage.
Risk of injury to children!
Follow these precautions to prevent the
TV from toppling over and causing injury to
children:
Never place the TV on a surface covered
by a cloth or other material that can be
pulled away.
Ensure that no part of the TV hangs over
the edge of the surface.
Never place the TV on tall furniture (such
as a bookcase) without anchoring both
the furniture and TV to the wall or a
suitable support.
Educate children about the dangers of
climbing on furniture to reach the TV.
Risk of overheating!
Never install the TV in a space.
Always leave a space of at least 4 inches
or 10 cm around the TV for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the TV.
Risk of damage to the TV!
Before you connect the TV to the power
outlet, ensure that the power voltage
matches the value printed on the back
of the TV. Never connect the TV to the
power outlet if the voltage is different.
Risk of injury, fire or power cord damage!
Never place the TV or any objects on the
power cord.
To disconnect the TV power cord easily
from the power outlet, ensure that you
have full access to the power cord at all
times.
PE Electronics Ltd
for improper wall
accident, injury or
confined
flat
, level
EN 3
Page 5
When you disconnect the power cord,
always pull the plug, never the cable.
Disconnect the TV from the power
outlet and antenna before lightning
storms. During lightning storms, never
touch any part of the TV, power cord or
antenna cable.
Risk of hearing damage!
Avoid using earphones or headphones at
high volumes or for prolonged periods of
time.
Low temperatures
If the TV is transported in temperatures
below 5
until the TV temperature matches room
temperature before connecting the TV to
the power outlet.
C, unpack the TV and wait
Screen care
Avoid stationary images as much as
possible. Stationary images are images
that remain on-screen for extended
periods of time. Examples include:
on-screen menus, black bars and time
displays. If you must use stationary
images, reduce screen contrast and
brightness to avoid screen damage.
Unplug the TV before cleaning.
Clean the TV and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the TV.
Risk of damage to the TV screen!
Never touch, push, rub or strike the screen
with any object.
To avoid deformations and colour fading,
wipe off water drops as soon as possible.
Disposal of your old product and
batteries
Your product is designed and manufactured
with high quality materials and
which can be recycled and reused.
components,
4 EN
Page 6
3 Your TV
Side controls and indicators (LCD 22PFL4506/V7)
3
2
4
1
1. SOURCE: Display source menu.
30 30
TV
USB
SCENEA
FREEZE
EXIT
1: Remote control sensor.
2: LED Indicator:
No light: In Power ON/Power OFF condition.
Red light: In Standby condition.
3: Key board
4: Main Power Switch (Bottom side).
2. MENU: Display main MENU.
3. CH+/CH-: In TV mode, press "CH+" or
"CH-" to change the channel up and down. In
MENU mode, press "CH+" or "CH-" to select
items. In standby mode, press "CH+" or "CH-"
to turn on the TV.
4. VOL+/VOL-: Adjust sound level. In MENU
mode, press "VOL+" or "VOL-" to adjust the
item that you selected.
5. STANDBY: Press this button to turn the TV
ON from STANDBY mode. Press it again to
turn the set back to STANDBY.
6.USB
SOURCE
MENU
CH+
CH-
VOL+
VOL-
STANDBY
USB
1
2
3
4
5
6
Sockets
AC-INP UT
110-240V ~ 50/60 Hz
1.HDMI Input
2.Component Video (YPbPr) Input
3.Audio Input (Common for Composite and component)
4.VGA Port (PC Input)
5.Composite Video Input (AV1)
6.PC Audio Input
7.AV2 IN/AV OUT (The socket can be used to connect AV2 IN/AV OUT adapter cable).
Note : When connecting the AV Adapter cable,please make sure the side with triangular
mark towards the inside.
8.Antenna Socket
Note: 1.Composite video input and component video input share the audio input.
2.When "DVI to HDMI cable" is used, the audio output for DVI needs to be connected
to the PC Audio Input.
EN 5
HDMI1 I NPUT HDMI2 INPU T
PrYPb
AV1 VIDEO
L
AV1
AUDIO
R
AUDIO INP UT
PC
AV2 IN AV OUT
RF INPUT
/
Page 7
3 Your TV
Side controls and indicators (LCD 26PFL4306/V7)
3
4
2
1
30 30
TV
USB
SCENEA
FREEZE
EXIT
1. SOURCE: Display source menu.
2. MENU: Display main MENU.
3. CH+/CH-: In TV mode, press "CH+" or
"CH-" to change the channel up and down.
In MENU mode, press "CH+" or "CH-" to
1: Remote control sensor.
2: LED Indicator:
No light: In Power ON/Power OFF condition.
Red light: In Standby condition.
3: Key board
4: Main Power Switch (Back side).
select items. In standby mode, press "CH+"
or "CH-" to turn on the TV.
4. VOL+/VOL-: Adjust sound level. In MENU
mode, press "VOL+" or "VOL-" to adjust the
item that you selected.
5. STANDBY: Press this button to turn the
TV ON from STANDBY mode. Press it again
to turn the set back to STANDBY.
6.USB
7.VIDEO INPUT
8.AUDIO INPUT-L
9.AUDIO INPUT-R
Sockets
SOURCE
MENU
CH+
CH-
VOL+
VOL-
STANDBY
1
2
USB
USB
3
USB
6
USB
4
VIDEO
5
VIDEO
L
R
7
L
AV2
8
R
9
HDMI1 IN PUT HDMI2 INPU T
AV1 VIDEOPrY
AV1
L
Pb
AUDIO
R
AUDIO INPU T
PC
RF INPUT
AUDIO
OUTPUT
L
VIDEO
R
OUTPUT
1.HDMI Input
2.Component Video (YPbPr) Input
3.Audio Input (Common for Composite and component)
4.VGA Port (PC Input)
5.Composite Video Input (AV1)
6.PC Audio Input
7.Antenna Socket
8.Audio Output - Video+Audio output
Note: 1.Composite video input and component video input share the audio input.
2.When "DVI to HDMI cable" is used, the audio output for DVI needs to be connected
to the PC Audio Input.
6 EN
Page 8
4 Remote Control Functions
Note: -Remote Control ( Depending on the models) and operation of remote control
may be affected by bright artifical light near to the TV.
Most of your television's functions are available via the menus that appear on the
screen. The remote control supplied with your set can be used to navigate through
the menus and to configure all the general settings.
(On/Off button) Turns the TV on or off in standby.
FREEZE
TV
SCENEA
USB
EXIT
MENU Brings up the menu system.
FORMAT
SOURCE Press to select signal source.
DEMO
SCENEA Deletes the selected file in the playlist.
DUAL I/II
SLEEP
FREEZE
BACK A/CH
(MUTE)
SOUND
PICTURE
Selects a picture format.
TV Access the TV mode.
Access the USB mode.
USB
Toggles the demonstration menu on or off.
Switches Stereo and Nicam Stereo to
Mono. Selects first language (Dua lI)
or second language (Dual II) in bilingual programmes.
Sets a delay after which the TV switches off.
Freezes the picture.
EXIT Exits the menu system.
(up, down, left and right direction buttons) Highlights different
Items in the menu system and adjusts the menu controls.
OK Confirms your selection.
Returns to a previous screen.
Toggles between the current channel
Channel.
Displays the status information.
INFO
+/-
Increases or decreases volume.
Turns OFF the sound. Press again to restore the volume.
Scans up or down through the current channel list.
CH +/-
(numeric buttons) Enters channel numbers.
0-9
T oggles through the sound modes: Standard, Music,
Movie and Personal.
Toggles through the picture preset settings: Vivid, Bright,
Cinema, and Personal.
INCR. SURR,
Note: - TELETEXT, DEMO. SCENEA, DUAL I/II
keys depend on model.ing
and the last viewed
EN 7
Page 9
5 Use your TV
Switching on
Follow the instructions on this page on how to switch on your TV set and the remote
control before going on to following pages describing how to use the channel set-up
procedure.
1. Insert two AAA batteries in the remote control.
Precautions on using batteries:
- Only use the battery types specified.
- Make sure you use the correct polarity.
- Do not mix new and used batteries.
- Do not use rechargeable batteries.
- Do not expose batteries to excessive heat such as sunshine, fire or
throw them in a fire, recharge them or try to open them, as the like,
them to leak or explode.this could cause
- Remove the batteries from the remote control if you are not using it
period of time.for a long
2. Connect the power cable to a mains socket. (If the power cable is not
to the television, please first connect the power cable to the connected
television.)
Your TV set should only be connected to an AC supply. It must not be
connected to a DC supply. If the plug is detached from the cable, do
not, under any circumstances, connect it to a mains socket, as there is
a risk of electric shock.
Note: The figures are for representation only. The location of the power
the back of the television might differ depending on the model.socket at
3. Connect the outside aerial or cable network to the ANTENNA IN socket
at the back of the TV set.
The aerial socket (75 OHM - VHF / UHF / cable) can be used for
an external aerial or other equipment fitted with a modulator connecting
satellite receiver, etc.). We recommend that you do not (video recorder,
(video recorder, satellite receiver, etc.) to your connect other equipment
complicate the set-up procedure with TV set to begin with, so as not to
them when you have finished the additional steps involved. Connect
setting up the channels.
4. Switch the TV on by pressing the power button.
Note:
The location and name of the power button on the TV may vary
according to TV model, at back side or bottom side of the back cabinets.
If the TV set is in standby mode, press the button on the remote
control or the CH+/- buttons on the TV set to turn on the TV.
Switching off
To put the TV set into standby mode, press the button on the remote control. The TV set remains
powered up, but with low energy consumption.
To switch off the TV set, .
press the power button
8 EN
Page 10
1. MAIN GUIDE MENU
3. SOUND MENU
You can adjust the sound effect here such as
Treble,Bass, Balance etc.
Press to move, and press to adjust.
Watch TV Device List
Browse USB Setup
Watch TV: Change source to TV direct.
Browse USB: Change source to USB directly.
Device List: Go into the source list menu.
Setup: Go into the setup menu.
2. PICTURE MENU
You can adjust picture effect here, such as
contrast, brightness, etc.
Digital Crystal Clear: To enhance the picture
quality, You can Switch this feature ON or OFF.
Press to move, and press to adjust.
Picture
Sound
Features
Installation
Picture
Sound
Features
Installation
Smart Picture
Contrast
Brightness
Color
Hue
Sharpness
Digital Crystal Clear
Format
Color Temp.
Noise Reduction
Picture
Sound
Features
Installation
Smart Sound
Balance
Treble
Bass
Auto Volume
NOTE:
AVL: Auto Volume leveller: When this parameters
is on, then volume level gets automatically
adjusted, this feature acts as automatic volume
leveler which lower the sound output when the
sound modulation is high or by rising the sound
when the sound modulation is low.
2).There are four Smart Sound modes can be
selected, such as standard, music, movie, and
personal.
4. FEATURES MENU
You can adjust the Blue Screen on/off, OSD
Duration, sleep time etc.
Press to move, and press to adjust.
Picture
Sound
Features
Installation
OSD Duration
Blue Screen
Sleep Time
Factory Settings
When the source is PC, you can adjust H/VPosition, Clock, and so on.
NOTE:
1) Hue is available in NTSC system only.
2) There are four smart picture modes can be
selected, as Vivid, Cinema, Personal, and
Bright.
3) When Digital Crystal Clear is on, the contrast
and brightness is disabled.
EN 9
Page 11
4. FEATURES MENU IN PC SOURCE
You can adjust the Blue Screen on/off, OSD
Duration, sleep time, H/V-Position,Clock and
Phase etc.
Press to move, and press to adjust.
Picture
Sound
Features
Features
OSD Duration
Blue Screen
Auto Adjust
H-Position
V-Postion
Clock
Phase
Sleep Time
program number Frequency
1 45.25 MHZ ----- On
Delete Move
Back
Channel Edit
1 2
MENU
Skip
Name
3
Confirm
Name
Skip
OK
4
Delete
Press 1 button, the program will be deleted.
NOTE:
Within 15 minutes there is no signal, the TV
will auto sleep.
5. INSTALLATION MENU( for TV source
only)
You can search channels and edit programs
here.
Picture
Sound
Features
Installation
Color System
Sound System
Skip
Auto Search
Manual Search
Fine Tune
Channel Edit
1) Auto Search:
Search all the TV channels automatically.
2) Manual Search:
You can search the TV channels by manual
search.
3) Fine Tune:
If the picture is not clear you can fine tune the
channel.
4) Channel Edit:
You can Delete, Rename, Move, or Skip any
programs.
Move
Move the cursor to the program, press 2 button,
and press to move the program.
Skip
Press 3 button to skip this program.
Name
Move the cursor to the program, press 4 button
to rename the program.
Press to choose the character. Press to
move the cursor.
Press MENU/OK button to exit edit, Press EXIT
to exit the menu.
Note: The TV programs name only can be 5
characters.
6. USB MENU
Change source to USB
USB
Picture Music Video Text
Please make sure that the USB device have
plugged in the slot. There are four type media
item can be selected, such as Picture, music,
Video and text. Select the type media item by
pressing, press OK button to enter the disk
selection menu.
10 EN
Page 12
Music mode menu bar:
1/1
00:00:33/00:04:22
Return
C
Press the to select the right disk and press
OK to display media files and folder list or
choose Return to go back to the media type
selection menu.
Retu rn
Picture
Music
Video
Text
samp le (1)
samp le (2)
samp le (3)
samp le (4)
samp le (5)
samp le (6)
samp le (7)
samp le (8)
samp le (9)
Select the media file by pressing , then the
preview frame will pop up. Press and to
select or unselect the media file. Press the
button OK to play the media file in full screen.
When the media file (Picture, Music, Video,
Text ) is playing, press the OK or Info button to
display the control bar.
NOTE:
To Exit from Sub menu to Main USB Menu press
BACK on Remote Control.
To Exit from USB Source and switch to another
source:
1) Press Menu key, Select Device list and Select
the Source where you want to switch and press
OK key on Remote control.
2) Press Source key on remote and Select the
Source where you want switch and press OK key
on Remote control.
Music, picture, video, text mode control menu
bars
you can select the multimedia functions like Play,
Pause, FF, FR, Next, Previous, Stop etc.
Picture mode menu bar:
Pause Prev. Next Stop Repeat-All Music Playlist Info.
90 90
Rotate Rotate Zoom In Zoom Out
EN 11
Pause FR FF Prev. Next Stop
Playlist
Info.
Repeat-All
MUTE
00:00:33/00:04:22
Video mode menu bar:
00:00:33/00:04:22
AB
Zoom In
Repeat-All
None
00:00:33/00:04:22
Format
Zoom Out
Pause FR FF Prev. Next Stop
Playlist
Info.
Slow Forward
Step Goto Time
Text mode menu bar:
Prev Page
Next Page Prev. Next
Press to select the function icon, press OK
button to confirm the function.
Stop
Music Playlist
Info.
Press or EXIT button to exit the control bar.
NOTE:
You can adjust the audio track, subtitle, or program
in the Info menu while Playing the video file.
Choose the Info icon and press OK to display the
Info MENU.
In the movie mode, when you use FR, FF function,
The audio may be pause in several seconds to
synchronize the audio signal and video signal.
In text mode, press" <<,>>" to make page up and
page down.
: Music function
In text mode and in picture mode, music function
will play the music files ,which you selected in the
music mode.
When the USB device isn't supported, it may be
that the power of the USB device isn't enough.
7. SOURCE LIST MENU
Display the menu by pressing the source key and
Select the source by pressing OK key.
TV
AV1
AV2
YPbPr
PC
HDMI 1
HDMI 2
USB
Page 13
6 FAQ
Attention and Frequently Asked Questions:
Attention:
1. Some non-standard mobile storage device
not be recognized. Please change may/may
standard device.The USB should to use the
virus before using this function.be cleaned from
All file in the storage device cannot be edited
2.
Note: For coding files, there are many kinds
standard coding method, so this system Non-
guaranteed to support the file can not be
method.formats using any coding
Frequently Asked Questions:
1. Under the following conditions, this system cannot
decode the file and the file can not play normally:
-The parameters of file, such as the pixel of picture,
code rate of audio and video file, sampling rate of
audio file, exceed the limit of the system;
The format of file is not matched or the file is -
harmed.
2. Hot plug: Do not disconnect when the system is
reading or transmitting data, avoid damaging the
or the device.system
3. Pay attention to the power supply of the device
you are using a mobile hard disk or a digital when
the power supply is not sufficient or not camera. If
encounter problems during stable, you may
at all. In this case, operating or can not operate
the device and please restart the device, or unplug
supply is plug it again, and ensure that its power
normal.
4. The system supports standard USB 1.1and USB
devices, such as standard U-disks, Mp3 players, 2.0
hard disks, etc..mobile
5. For obtaining better audio and video quality,
to use the external device which accords suggests
standard.with USB 2.0
6. For some USB device with power supply, such as
size hard disk, Mp4, etc., Suggests using it large
to avoid electric power shortage.with power
12 EN
Page 14
7 Other Information
EN 13
Page 15
8 Product
information
Product information is subject to change
without notice. For detailed product
information, go to www.philips.com/support.
Supported display resolutions
Computer formats (HDMI)
Resolution - refresh rate:
640 x 480 - 60Hz, 72Hz, 75Hz
720 x 400 - 70Hz
800 x 600 - 56Hz, 60Hz, 72Hz
1024 x 768 - 60Hz, 70Hz, 75Hz
1280 x 960 - 60Hz
1280 x 1024 - 60Hz, 70Hz, 75Hz
Computer formats (VGA)
Resolution - refresh rate:
640 x 480 - 60Hz, 72Hz, 75Hz
720 x 400 - 70Hz
800 x 600 - 56Hz, 60Hz, 72Hz
1024 x 768 - 60Hz, 70Hz, 75Hz
1280 x 960 - 60Hz
1280 x 1024 - 60Hz, 70Hz, 75Hz
Video formats
Resolution - refresh rate:
480i - 60Hz
480p - 60Hz
576i - 50Hz
576p - 50Hz
720p - 50Hz, 60Hz
1080i Hz Hz - 50 , 60
1080p - 50Hz, 60Hz
(For FHD model only)
Multimedia
Supported USB storage device:
(Only FAT 16 or FAT 32 USB storage
devices are supported)
Supported storage file formats:
Images: JPEG, BMP, JPE, PNG.
Audio: Mp3
Video:
File Extension Container Video Decoder
*.avi
*.mp4/*.mov
*.mkv
*.mpg/*.mpeg
*.wmv
T EXT: TXT
AVI
MP4
MKV
PS
ASF
MPEG 1/2/4, H.264
MPEG 4, H.264
MPEG 4, H.264
MPEG 1/2
VC-1
Note
names must not exceed 128
Multimedia
characters.
file
Tuner/ Reception/
Transmission
Antenna input: 75ohm coaxial (IEC75)
TV system: PAL
Video playback: PAL, NTSC
Remote control
Batteries: 2 x AAA
Power
Mains power: AC 110-240V, 50-60Hz
Standby power W: <1
Ambient temperature to 40 degrees : 5
Celsius
14 EN
Page 16
Supported TV mounts
Product specifi
cation
To mount the TV, purchase a Philips TV mount
or a VESA-compatible TV mount. To prevent
damage to cables and connectors, be sure to
leave a clearance of at least 2.2 inches or 5.5cm
from the back of the TV.
TV screen
size (inches)
22PFL4506/V7
26PFL4306/V7
Required
pitch (mm)
100 X 100
100 X 200
Required
mounting bolts
4 x M4
4 x M4
Design and specifications are subject to change
without notice.
22PFL4506/V7
Without TV stand
Dimension (WxDxH): 530 x 97
x 352 (mm)
Weight: 4.7kg
26PFL4306/V7
Without TV stand
Dimension (WxDxH): 660 x 104
x 440 (mm)
Weight: 6.8kg
EN 15
Page 17
22PFL4506/V7
26PFL4306/V7
MADE IN PRC
Page 18
Page 19
Loading...