Philips 220V3SB/00, 220V3SB/00(AP), 220V3AB/00, 220V3SB/93, 220V3AB/01 Service Manual

...

Description Page

Important Safety Notice--------------------------------------2 Technical Data--------------------------------------------- -3~4 Installation-------------------------------------------------------5

On Screen Display-----------------------------------------8~9

Lock/unlock, Aging,Factory mode-------------------------10

---------------------------------11 Mechanical Instructions ------------------------------12~16

Color adjustment --------------------------------------------17

Electrical instruction ----------------------------------20~21

DDC Instructions & Serial Number -----------------24~30 DDC DATA -----------------------------------------------31~32

------------------------33~36

Philips Pixel Defect Policy

FAQs (Frequently Asked Questions)---------------18~19

Firmware Upgrade for CPU-

Horizontal frequencies

30-83kHz

TABLE OF CONTENTS

Description Page

-----------------------------------37

Wiring Diagram----------------------------------------------38 Block Diagram------------------------------------------------39

Power Control Diagram & C.B.A. -----------------------------47~48

Failure Mode Of Panel -

SAFETY NOTICE

Chassis:

REFERTO BACK COVER FOR

IMPORTANT SAFETY GUIDELINES

ANY PERSON

ATTEMPTING TOSERVICE THIS CHASSIS

MUST FAMILIARIZE

HIMSELF

WITH THE

CHASSIS

AND BE AW ARE OF THE NECESSAR Y SAFETY PRECAUTIONS

TO BE USED WHEN

SERVICING ELECTRONIC

EQUIPMENT CONTAINING

HIGH VOLTAGES.

CAUTION:

USE

A SEPARATE

ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.

Published by Philips Consumer Lifestyle Copyright reserved Subject to modification JDec. 09 2011

Scaler Diagram & C.B.A. ------------------------------40~43

MERIDIAN 3

Troubleshooting---------------------------------------------6~7

Service Tool-----------------------------------------------22~23

220V3SB/00

inch

General product specification------------------------49~73 Exploded View -----------------------------------------------74

Spare/ arts List-------------------------75

Recommended P

PCBA photos---------------------------------------------------76

Repair tips-------------------------------------------------77~78 Repair Flow chart----------------------------------------79~80 Safety Test Requirments------------------------------------81

WSXGA

LCD Colour Monitor

TFT

Diagram & C.B.A.

------------------------------44~46

220V3SB/00(AP) 220V3SB/01 220V3SB/62 220V3SB/93 220V3AB/00 220V3AB/00(AP)

220V3AB/01

Auto Color & User reset

--------------------------------82~83

Important Safety Notice

Proper service

operation of all Philips Consumer Electronics Co

mpany

equipment. The service procedures

commended by

Phil

ips and

described in this service manual a

re eff

ect

ive method

sof

performing service ope

rations

.Someof

these servic

operations require the useof tools speciall y designed

for the

purpose. The spe

cial tools should be used w

hen and as

recomm ended.

It is im portant to note t hat this m anual c ontains various

CAUTI ON

S and NOTICES which should be

carefully read in

order to m inimize the risk of personal injury to servic

personnel . The possibility exists th

at im

proper

servi

methods may damage the equipment

. It is also important t

underst and that these CAUTIONS and NOTICES ARE NOT

EXHAUSTIVE. Phil

ips

could not possibly know, evaluate and

advise the servic etrade of all conceivable ways i n w

hic

service might be done or of the possible hazardous

consequences of each way. Consequently,Philips has not

undertaken any suc

h broad evalua

on. Accordingly

who uses a servi ce procedure or tool which is not

recommended by Philipsmust f

irst sati

sfy

himself thoroughly that

neither his saf ety nor the safeoperation of the equipment will

be jeopardized by the servi

ce method sel

ect ed.

* * Hereafter throughout this manu

al,

PhilipsConsumer

Electronics Company will be referred to as Philips

Critical components havingspecial safety characteristics are

identified with a by the Ref. No. in the parts list and

enclosed within a broken line

(where several critical co

mponents are grouped in

one area)

along with t

he safe

ty s

mbol on the schem atics

exploded vie

ws.

Use of substitute replacement parts w hich do no

t have the

same speci fied safety characteristic s may create

shock,

fire,

or other hazards .

Under no cir cumstances should th

e original

design be

modified or altered without written permission from Philip

Philips assumes no liabilit

y, express or implied, arising

out of

any unauthorized modification of design.

Servicer assumes all liability.

WARNING

Take care during handling the LCD module with backlight

unit

- Must mount the module using mounting holes arranged in four

corners.

- Do not press on the panel, edge of the frame strongly or electric

shock as this will result in damage to the screen.

- Do not scratch or press on the panel with any sharp objects, such

as pencil or pen as this may result in damage to the panel.

- Protect the module from the ESD as it may damage the electronic

circuit (C -MOS).

Make certain that treatment body are grounded through

wrist band.

- Do not leave the module in high temperature and

in areas of high

humidity for a long time.

- Avoid contact with water as it may as hort circuit within the module.

If the surface of panel become dirty

, please wi

pe it off with a soft

material. (Cleaning with a dirty or rough cloth may damage the

panel.)

FOR PRODUCTS CONTAINING LASER :

DANGER - Invisible laser radiation when open.

AVOID DIRECT EXPOSURE T

O BEAM.

CAUTION - Use of controls or adjustments or

performance of procedures other than

those specified herein may result

hazardous radiation exposure.

CAUTION - The use of optical instruments with this

product will increase eye hazard.

TO ENSURE THE CONTINUED RELIABILITY

OF THIS

PRODUCT, USE ONLYORIGINAL

MANUF

ACTURER'S

REPLACEMENT PAR TS, WHICH ARE LISTED WITH THEIR P

ART

NUMBERS IN THE PAR

TS LIST SECTION OF

THIS

SERVICE MANUAL.

and repair is important

to the sa

fe,

reliable

2 220V3 LCD

220V3 LCD 3

Technical Data

LGD

Type NR.

: LGD LM220WE1 TLP1

Resolution

: 1680x1050

Outside dimensions

: 493.7(H) *320.1(V) * 14.5 (D) mm(Typ.)

Pitch (mm) : 0.282mm x 0.282mm

Color pixel arrangement

: 1680 horizontal By 1050 vertical PVV9C ixels. RGB stripe arrangement.

Display surface

: Hard coating (3H), Anti-glare treatment of the front polarizer

Color depth

: 16.7 M colors 6-bit with H-FRC,

16.7M colors

Backlight : 2CCFL

Active area (W x H)

: 473.76mm x 296.10mm

View angle (CR=10) : >=160 Right/Left (Typ)

: >=160 Up/Down (Typ)

Contrast ratio

: >=700:1 (Typ)

White luminance

: 250 cd/m2(Typ. Center 1 point)

Gate IC

:LDI

Color gamut : >=72% Response time : 5 ms (Typ) Vertical frequency

range

:50~75 Hz

Scanning frequencies

Hor.: 30 – 60 K Hz

Ver.: 56 - 63 Hz

Video dot rate: < 210 MHz for VGA and < 170 MHz for DVI

Power input: 90-264 V AC, 50/60 r 2 Hz

Power consumption: Normal on: < 30 W (max)

Functions: (1) D-SUB analog R/G/B separate inputs, H/V sync

separated, Composite (H+V) TTL level, SOG sync.

(2)SOG sync: a. Sync select: H + V b. Sync select: SERR

(3) DVI digital Panel Link TMDS inputs, HDCP supported.

Ambient temperature: 0

C-40qC

Power input connection

Power cord length : 1.5 M

Power cord type : 3 leads power cord with protective earth plug.

Power management

Mode HSYNC VSYNC Video Pwr-cons. Indication

Power-On On On Active

<25W (typ.)

<32W(max.)

CCFL(220V3)

<30W (typ.)

<37W(max.)

CCFL(220V3A)

Standby Off Off Blanked < 0.5W

Blinking white

LED

Period 3ec

on, 3sec off

DC Power

Off

N/A < 0.5 W LED Off

PIN No. SIGNAL PIN No. SIGNAL

1 Red 9 DDC +3.3V or +5V 2 Green/ SOG 10 Logic GND 3 Blue 11 Sense (GND) 4 Sense (GND) 12 Bi-directional data 5 Cable Detect (GND) 13 H/H+V sync 6 Red GND 14 V-sync 7 Green GND 15 Data clock 8 Blue GND

Susceptibility of display to external environment

Operating

- Temperature : 0 to 40 degree C

- Humidity : 80% max

- Altitude : 0-3658m

- Air pressure : 600-1100 mBAR

Storage

- Temperature : -20 to 60 degree C

- Humidity : 95% max

-Altitude :0-12192m

- Air pressure : 300-1100 mBAR

Note: recommend at 5 to 35qC, Humidity less than 60 %

Pin No. Description

1 T.M.D.S. data2-

2 T.M.D.S. data2+

3 T.M.D.S. data2 shield

4 No Connect

5 No Connect

6 DDC clock

7 DDC data

8 No Connect

9 T.M.D.S. data1-

10 T.M.D.S. data1+

11 T.M.D.S. data1 shield

12 No Connect

13 No Connect

14 +5V Power

15 Ground (for +5V)

16 Hot plug detect

17 T.M.D.S. data0-

18 T.M.D.S. data0+

19 T.M.D.S. data0 shield

20 No Connect

21 No Connect

22 T.M.D.S clock shield

23 T.M.D.S. clock+

24 T.M.D.S. clock-

4 220V3 LCD

Technical Data

SEC

Type NR.

: SEC LTM220MT05

Resolution

: 1680x1050

Outside dimensions

: 493.7(H) *320.1(V) * 17 (D) mm(Typ.)

Pitch (mm) : 0.282mm x 0.282mm

Color pixel arrangement

: 1680 horizontal By 1050 vertical PVV9C ixels. RGB stripe arrangement.

Display surface

: Hard coating (3H), Anti-glare treatment of the front polarizer

Color depth

: 16.7 M colors 6-bit with H-FRC,

16.7M colors

Backlight : 2CCFL

Active area (W x H)

: 473.76mm x 296.10mm

View angle (CR=10) : >=160 Right/Left (Typ)

: >=160 Up/Down (Typ)

Contrast ratio

: >=700:1 (Typ)

White luminance

: 250 cd/m2(Typ. Center 1 point)

Gate IC

:LDI

Color gamut : >=72% Response time : 5 ms (Typ)

Scanning frequencies

Hor.: 30 – 60 K Hz

Ver.: 56 - 63 Hz

Video dot rate: < 210 MHz for VGA and < 170 MHz for DVI

Power input: 90-264 V AC, 50/60 r 2 Hz

Power consumption: Normal on: < 30 W (max)

Functions: (1) D-SUB analog R/G/B separate inputs, H/V sync

separated, Composite (H+V) TTL level, SOG sync.

(2)SOG sync: a. Sync select: H + V b. Sync select: SERR

(3) DVI digital Panel Link TMDS inputs, HDCP supported.

Ambient temperature: 0

C-40qC

Power input connection

Power cord length : 1.5 M

Power cord type : 3 leads power cord with protective earth plug.

Power management

Mode HSYNC VSYNC Video Pwr-cons. Indication

Power-On On On Active

<25W (typ.)

<32W(max.)

CCFL(220V3)

<30W (typ.)

<37W(max.)

CCFL(220V3A)

Standby Off Off Blanked < 0.5W

Blinking white

LED

Period 3ec

on, 3sec off

DC Power

Off

N/A < 0.5 W LED Off

PIN No. SIGNAL PIN No. SIGNAL

Susceptibility of display to external environment

Operating

- Temperature : 0 to 40 degree C

- Humidity : 80% max

- Altitude : 0-3658m

- Air pressure : 600-1100 mBAR

Storage

- Temperature : -20 to 60 degree C

- Humidity : 95% max

-Altitude :0-12192m

- Air pressure : 300-1100 mBAR

Note: recommend at 5 to 35qC, Humidity less than 60 %

Pin No. Description

1 T.M.D.S. data2-

2 T.M.D.S. data2+

3 T.M.D.S. data2 shield

4 No Connect

5 No Connect

6 DDC clock

7 DDC data

8 No Connect

9 T.M.D.S. data1-

10 T.M.D.S. data1+

11 T.M.D.S. data1 shield

12 No Connect

13 No Connect

14 +5V Power

15 Ground (for +5V)

16 Hot plug detect

17 T.M.D.S. data0-

18 T.M.D.S. data0+

19 T.M.D.S. data0 shield

20 No Connect

21 No Connect

22 T.M.D.S clock shield

23 T.M.D.S. clock+

24 T.M.D.S. clock-

220V3 LCD 5

Installation

Front View Product Description

Rear View

Accessory Pack

Unpack all the parts

Connecting to Your PC

1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected VGA cable for the first installation.

6 220V3 LCD

Troubleshooting

220V3 LCD 7

Troubleshooting

8 220V3 LCD

On-Screen Display

Description of the On Screen Display

What is the On-Screen Display?

On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or

select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display

interface is shown as below :

Basic and simple instruction on the control keys.

In the OSD shown above users can press

buttons at the front bezel of the monitor to move the cursor, to

confirm the choice or change.

220V3 LCD 9

On-Screen Display

The OSD Tree

Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work

your way around the different adjustments later on.

10 220V3 LCD

Lock/Unlock,Aging,Factory Mode

To lock/unlock OSD FUNCTION(User Mode)

The OSD function can be locked by pressing"OK"button(1) for more than 10 seconds, the screen shows following windows for 4 seconds. Every time when you press"OK" button, this message appears on the screen automatically .

Unlock OSD function

Unlocked OSD function can be released by pressing "OK" button for more than 10 seconds again.

Access Factory Mode

1). Turn off monitor.

2). [Push "EXIT" & "MENU" buttons at the same time and hold them]+[Press "power" button until comes out "Windows screen" ] => then release all buttons

3).Press "MENU" button, wait until the OSD menu with Characters " MERIDIAN 220V3 V1.0 11-10-13” (below OSD menu) come on the Screen of the monitor.

Factory Mode indicator

Factory Menu

Cursor can move on gray color area Hot key function: by pressing " UP " and " DOWN " key Simultaneously at User Mode (or Factory Mode) (PS: The Of fset R G B function can be used on reduce or eliminate snowy noise on the background when the resolution of video signal is 1680*1050vertical 60Hz. Slightly increase or decrease the value until snowy noise completely disappear .

Access Aging Mode

Step 1 : Access Factory Mode then enter Factory Menu. Step 2 : By pressing " UP" and " DOWN " key to Burning Icon. Press "MENU then press " UP" and "DOWN " key to turn on Aging Mode.

Step 3 : Disconnect interface cable between Monitor and PC.

After 3 seconds, bring up:

repeatly Connect Signal cable again=> go back to normal display

220V3 LCD 11

Philips Pixel Defect Policy

Philips' Flat Panel Monitors Pixel Defect Policy

Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This notice explains the different types of pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 19" XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain types or combinations of pixel defects that are more noticeable than others. This policy is valid worldwide.

Pixels and Sub pixels

A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors.

Types of Pixel Defects

Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category.

Bright Dot Defects Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. That is, a bright dot is a sub-pixel that stands out on the screen when the monitor displays a dark pattern. There are the types of bright dot defects:

One lit red, green or

blue sub pixel

Two adjacent lit sub

pixels:

- Red + Blue =

Purple

- Red + Green =

Yellow

- Green + Blue =

Cyan (Light Blue)

Three adjacent lit sub

pixels (one white

pixel)

A red or blue bright dot must be more than 50 percent brighter

than neighboring dots while a green bright dot is 30 percent

brighter than neighboring dots.

Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. That is, a dark dot is a sub-pixel that stands out on the screen when the monitor displays a light pattern. These are the types of black dot defects:

One dark sub pixel Two or three adjacent dark sub pixels

Proximity of Pixel Defects

Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects.

Pixel Defect Tolerances

In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.

BRIGHT DOT DEFECTS

ACCEPTABLE

LEVEL

MODEL

220V3(L)(A)

1 lit subpixel 3

2 adjacent lit subpixels 1

3 adjacent lit subpixels (one white pixel) 0

Distance between two bright dot defects* >15mm

Total bright dot defects of all types 3

BLACK DOT DEFECTS

ACCEPTABLE

LEVEL

MODEL

220V3(L)(A)

1 dark subpixel 5 or fewer

2 adjacent dark subpixels 2 or fewer

3 adjacent dark subpixels 0

Distance between two black dot defects* >15mm

Total black dot defects of all types 5 or fewer

TOTAL DOT DEFECTS

ACCEPTABLE

LEVEL

MODEL

220V3(L)(A)

Total bright or black dot defects of all types

5 or fewer

Note:

* 1 or 2 adjacent sub pixel defects = 1 dot defect

220V3 LCD

Mechanical Instruction

Preparation before disassemble

1.Clean the room for disassemble

2.Identify the area for monitor

3.Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow;

according to the actual condition plan the disassemble layout

4.Prepare the implement, equipments, materials as bellow:

1) Press-fixture

2) working table

3) Screw-driver

4) knife*1

5) glove

6) cleaning cloth

7) ESD protection

item picture Operation Tool Notes

Press the locking clips to

detach the base stand

away from the base

column.

1 Presses the button, at the

same tine remove the

CLMN BTM.

220V3 LCD

2 Remove CVR Hinge knife

3 Disassemble the screws,

and then remove ASSY

CLMN

Screw-driver

4 Turn over the monitor,

break BZL and RC apart.

And Turn over the

monitor again, remove

RC.

Follow the

order of the

picture

Pull out the SPK wire

Disassemble the SPK.

220V3A,220V3LA

220V3 LCD

Remove the tapes,

remove the

AL-Tape

unlock lamp wire, CTRL

BD wire from PCBA,

unlock LVDS FFC wire

from Panel.

7 Break SHD and BZL

apart.

Be careful :

do not break

the rib and

column

220V3L

220V3

220V3 LCD

Remove Panel, and then

disassemble CTRL BD

from the BZL.

Disassemble CTRL BD

wire.

Be careful :

do not break

the rib on

the CTRL

BD .

Disassemble screw mach

steel˖

1A˖2pcs,

1A1D˖4pcs

Screw-driver

Turn over the SHD

Diassemble 6 crews

Screw-driver

234

220V3 LCD

11 Take PCBA out from

SHD.

Unlock power BD wire

from IF BD, unlock LVDS

FFC wire from IF BD

220V3 LCD 17

Color Adjustment

Alignment procedure

1. Turn on the LCD monitor

2. Turn on the Timing/pattern generator. See Fig.1

3. Preset LCD color Analyzer CA-1 10

-Remove the lens protective cover of probe CA-A30.

-Set measuring/viewing selector to measuring position for reset analyzer .(zero calibration) as Fig.2

- Turn on the color analyzer (CA-1 10)

-Press 0-CAL button to starting reset analyzer .

Fig. 1 Fig.2

4. Access Factory Mode

1). Turn off monitor.

2). [Push "AUTO" & "MENU" buttons at the same time and hold them]

+[Press "power" button untill comes out "Windows screen" ] => then release all buttons

3).Press "MENU button, wait until the OSD menu with Characters " MERIDIAN 220V3 V1.0 11-10-13” (below OSD menu) come on the Screen of the monitor as shown in Fig3.

Factory Mode indicator

Fig. 3

4). Press button, then select factory mode indicator by "MENU" "LEFT" or "RIGHT" button .Press"MENU" button to bring up submenu windows as below:

Fig. 4

Fig.5

5.Display Press "UP" or "DOWN" button to select . Change the value by "UP" or "DOWN" key until the X, Y co-ordinates as below

5.1

Color temperature adjustment There are six factory preset white color 11500K, 9300K, 8200K, 7500K, 6500K, sRGB, 5000K Align by Philips PerfecTune (also called FGA) function. Apply full white pattern, with brightness in 100 % position and the contrast control at 50 % position. The 1931 CIE Chromaticity (color triangle) diagram (x , y) coordinate for the screen center should be:

Product specification

CIE coordinates

(x,y)

11500K x = 0.270 ± 0.02

= 0.281 ± 0.02

PerfecTune II

9300K x = 0.283 ± 0.02

= 0.297 ± 0.02

PerfecTune II

8200K x = 0.291 ± 0.02

= 0.306 ± 0.02

PerfecTune II

7500K x = 0.298 ± 0.02

= 0.314 ± 0.02

PerfecTune II

6500K/sRGB x = 0.313 ± 0.02

= 0.329 ± 0.02

PerfecTune II

sRGB x = 0.313 ± 0.02

= 0.329 ± 0.02

PerfecTune II

5000K x = 0.345 ± 0.02

= 0.357 ± 0.02

PerfecTune II

Production alignment spec

CIE

coordinates

(x,y)

11500K x = 0.270 ± 0.006

= 0.281 ± 0.006

PerfecTune II

9300K x = 0.283 ± 0.006

= 0.297 ± 0.006

PerfecTune II

8200K x = 0.291 ± 0.006

= 0.306 ± 0.006

PerfecTune II

7500K x = 0.298 ± 0.006

= 0.314 ± 0.006

PerfecTune II

6500K/sRGB x = 0.313 ± 0.006

= 0.329 ± 0.006

PerfecTune II

sRGB x = 0.313 ± 0.006

= 0.329 ± 0.006

PerfecTune II

5000K x = 0.345 ± 0.006

= 0.357 ± 0.006

PerfecTune II

Quality Inspection specification

CIE

coordinates

(x,y)

9300K x = 0.283 ± 0.015

= 0.297 ± 0.015

6500K/sRGB x = 0.313 ± 0.015

= 0.329 ± 0.015

sRGB x = 0.313 ± 0.015

= 0.329 ± 0.015

18 220V3 LCD

FAQs (Frequently Asked Questions)

220V3 LCD 19

FAQs (Frequently Asked Questions)

20 220V3 LCD

Electrical Instructions

Electrical characteristics

1. Interface signals

1.1 D-Sub Analog Input signal: Video, Hsync., Vsync Video: 0.7 Vp-p, input impedance, 75 ohm @DC Sync.: Separate sync TTL level , input impedance 2.2k ohm terminate

Hsync Positive/Negative Vsync Positive/Negative

Composite sync TTL level, input impedance 2.2k ohm terminate (Positive/Negative)

Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive)

1.2 DVI-D Digital Input signal: Single TMDS link (Three channels: RX0-/+, RX1-/+, RX2-/+)

2. Interface

2.1 D-Sub Cable Length : 1.5 M +/- 50 mm Fix with monitor when packing, with transplant pin protective cover. Connector type : D-Sub male with DDC2B pin assignments.

Blue connector thumb-operated jack screws

2.2 DVI Cable

The input signals are applied to the display through DVI-D cable.

Length : 1.8 M +/- 50 mm

Connector type : DVI-D male with DDC-2B pin assignments White connector thumb-operated jackscrews With transplant pin protective cover.

3. Timing requirement

3.1 Factory Preset mode definitions:

3.1.1 Perfect FOS while presenting those timings.

3.1.2 Will specify those timing in User's Manual

3.2 Preset mode definition:

3.2.1 Need to support those timings.

3.2.2 Perfect FOS after auto adjustment.

3.3 User mode

3.3.1 Can save those timing that not in Preset mode and can be showed (not over scalar or Panel spec.)

3.3.2 It needs to reserve the 10 timings space in memory size.

3.3.3 Factory modes and preset modes are defined in the enclosed timing table file

Preset mode Timing

Factory Preset

mode

Timing

Preset mode Timing

Factory Preset

mode

Timing

Preset mode Timing

Factory

Preset mode Timing

res et

mod

Preset mode

Timing

Factory Preset

mode Timing

57 17 57 16 53 15 54 16 5

DOS 640x350/70

25.18 31.47 70.09 449 p / n * * * *

DOS 720x400/70

28.3231.4770.09449n / p******** *

DMT 4:3 640x480/60

25.1831.4759.94525n / n******** *

MAC 640x480/67

30.2435.0066.67525n / n*******

DMT 4:3 640x480/72

31.5037.8672.81520n / n*******

DMT 4:3 640x480/75

31.5037.5075.00500n / n*******

DMT 4:3 640x480/85

36.00 43.27 85.01 509 n / n

DMT 4:3 800x600/56

36.00 35.16 56.25 625 p / p * * * *

DMT 4:3 800x600/60

40.0037.8860.32628p / p******** *

DMT 4:3 800x600/72

50.00 48.08 72.19 666 p / p * * * *

DMT 4:3 800x600/75

49.5046.8875.00625p / p*******

DMT 4:3 800x600/85

56.25 53.67 85.06 631 p / p

MAC 832x624/75

57.28 47.73 74.55 667 n / n * * * *

960x720/60

57.58 44.74 59.97 746 n / p

960x720/75

72.42 56.40 75.00 752 n / p

WVGA 1024X600/60

****

DMT 4:3 1024x768/60

65.0048.3660.00806n / n******** *

DMT 4:3 1024x768/70

75.00 56.48 70.07 806 n / n * * * *

DMT 4:3 1024x768/75

78.7560.0275.03800p / p*******

IBM 1024x768/76

83.10 61.10 76.00 803 p / p * * * *

DMT 1024x768/85

94.50 68.68 85.00 808 p / p

1152x864/60

79.90 54.00 60.00 900 p / p * * * *

1152x864/70

94.50 63.90 70.00 912 p / p * * * *

DMT 1152x864/75

108.00 67.50 75.00 900 p / p * * * *

MAC 1152x870/75

100.00 68.68 75.06 915 n / n * * * *

SUN 1152x900/66

92.94 61.80 65.95 937 p / p * * * *

SUN 1152x900/76

105.56 71.71 76.05 943 p / p * * * *

CVT 16:9 1280x720/60

74.50 44.77 59.86 748 n / p * * * *

1280x720/70

89.04 52.50 70.00 750 n / p * * *

CVT 16:9 1280x720/75

95.75 56.46 74.78 755 n / p * * *

CVT 16:9 1280x720/85

110.25 64.40 84.85 759 n / p

CVT 15:9 1280x768/60

79.50 47.78 59.87 798 n / p * * * *

CVT 15:9 1280x768/75

102.25 60.29 74.89 805 n / p * * * *

CVT 15:9 1280x768/85

117.50 68.63 84.84 809 n / p

CVT 1280x800/60

83.50 49.70 59.81 831 n / p * * * *

CVT 1280x800/75

106.50 62.80 74.93 838 n / p * * * *

CVT 1280x800/85

122.50 71.55 84.88 843 n / p

DMT 4:3 1280x960/60

108.00 60.00 60.00 1000 p / p * * *

CVT 4:3 1280x960/75

130.00 75.23 74.86 1005 n / p * * *

DMT 4:3 1280x960/85

148.50 85.94 85.00 1011 p / p

DMT 5:4 1280x1024/60

108.00 63.89 60.02 1066 p / p *******

SUN 5:4 1280x1024/66

117.00 71.70 67.00 1067 p / p * * * *

DOS 5:4 1280x1024/72

130.22 76.00 72.00 1064 p / p * * * *

DMT 5:4 1280x1024/75

135.00 79.98 75.03 1066 p / p *******

SUN 5:4 1280x1024/76

138.01 81.10 76.00 1066 n / n * * * *

DMT 5:4 1280x1024/85

157.50 91.15 85.02 1072 p / p

DMT 16:9 1360x768/60

85.50 47.71 60.02 795 p / p *

CVT 16:9 1360x768/75

109.00 60.29 74.89 805 n / p

CVT 16:9 1366x768/60

85.50 47.71 59.79 798 p / p * *

CVT 4:3 1400x1050/60_RB

101.00 64.74 59.94 1080

CVT 4:3 1400x1050/75

156.00 82.28 74.87 1099

CVT 4:3 1400x1050/85

179.50 93.88 84.96 1105

CVT 1440x900/60_RB

88.75 55.47 59.90 926 p / n * * * *

CVT 1440x900/60

106.50 55.94 59.89 934 n / p *******

CVT 1440x900/75

136.75 70.64 74.98 942 n / p *******

CVT 1440x900/85

157.00 80.43 84.84 948 n / p

VDMTREV 1600x900/60

108.00 60.00 60.00 *

1600x900/75

75.00

1600x1000/60

DMT 4:3 1600x1200/60

162.00 75.00 60.00 1250 p / p * * * *

CVT 16:10 1680x1050/60_RB

119.00 64.67 59.88 1080 p / n * * * * *

CVT 16:10 1680x1050/60

146.25 65.29 59.95 1089 n / p *******

CVT 16:10 1680x1050/75

187.00 82.31 74.90 1099 *

CVT 16:9 1920x1080/60_RB

138.50 66.59 59.93 1111 p / n * * * *

CVT 16:9 1920x1080/60_RB

148.50 67.50 60.00 1125 p / p * * * *

CVT 16:9 1920x1080/60

173.00 67.16 59.96 1120 ****

CVT 16:10 1920x1200/60_RB

154.00 74.04 59.95 1235 p / n * * * *

CVT 16:10 1920x1200/60

193.25 74.56 59.89 1245 n / p * * *

480i

*****

480p

*****

720p

*****

1080i

*****

1080p

*****

576i

*****

576p

*****

720p

*****

1080i

*****

1080p

*****

1080p

Video Timing VGA,DVI,HDMI and DisplayPort need to do internal firmware support

00X

Resolution

Pixel Rate

( MHz )

Horizont

( KHz )

Vertical

( Hz )

V_Total

( Line )

50Hz

1366X768 Note book panel

24Hz

Polarity ( H / V )

1920X1200 1920X1080 1680X1050

60Hz

220V3 LCD 21

Electrical Instructions

White color adjustment

There are three factory preset white color 9300K, 6500K, sRGB. Apply full gray64 pattern, with brightness in 100 % position and the contrast control at 50 % position.The 1931 CIE Chromaticity (color triangle) diagram (x ,y) coordinate for the screencenter should be:

Product specification

CIE coordinates (x,y)

11500K x = 0.270 ± 0.02

y = 0.281 ± 0.02

PerfecTune II

9300K x = 0.283 ± 0.02

y = 0.297 ± 0.02

PerfecTune II

8200K x = 0.291 ± 0.02

y = 0.306 ± 0.02

PerfecTune II

7500K x = 0.298 ± 0.02

y = 0.314 ± 0.02

PerfecTune II

6500K/sRGB x = 0.313 ± 0.02

y = 0.329 ± 0.02

PerfecTune II

sRGB x = 0.313 ± 0.02

y = 0.329 ± 0.02

PerfecTune II

5000K x = 0.345 ± 0.02

y = 0.357 ± 0.02

PerfecTune II

Production alignment spec.

CIE coordinates (x,y)

11500K x = 0.270 ± 0.006

y = 0.281 ± 0.006

PerfecTune II

9300K x = 0.283 ± 0.006

y = 0.297 ± 0.006

PerfecTune II

8200K x = 0.291 ± 0.006

y = 0.306 ± 0.006

PerfecTune II

7500K x = 0.298 ± 0.006

y = 0.314 ± 0.006

PerfecTune II

6500K/sRGB x = 0.313 ± 0.006

y = 0.329 ± 0.006

PerfecTune II

sRGB x = 0.313 ± 0.006

y = 0.329 ± 0.006

PerfecTune II

5000K x = 0.345 ± 0.006

y = 0.357 ± 0.006

PerfecTune II

Quality Inspection specification:

CIE coordinates (x,y)

9300K x = 0.283 ± 0.015

y = 0.297 ± 0.015

6500K/sRGB x = 0.313 ± 0.015

y = 0.329 ± 0.015

sRGB x = 0.313 ± 0.015

y = 0.329 ± 0.015

22 220V3 LCD

Service tool-Hardware

PCM code 12NC

5E.L8215.001 996510019769

1. (For DDC update)

2. (For FW update)

RTD USB ISP BD

220V3 LCD 23

Service tool-Software

FW writing tool :

RTD_Customer_Tool_V2.1_Beta3_Install_20110701.exe

24 220V3 LCD

DDC Instructions

DDC Data Re-programming

In case the DDC data memory IC or main EEPROM which storage all factory settings were

replaced due to a defect, the serial numbers have to be re-programmed "Analog

DDC IC, Digital DDC IC & EEPROM".

It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new

board if circuit board have been replaced, in this case the DDC data does not need to be

re-programmed.

Additional information

Additional information about DDC (Display Data Channel) may be obtained from Video

Electronics Standards Association (VESA).

Extended Display Identification Data(EDID) information may be also obtained from

VESA.

Configuration and procedure

"PI-EDID" The software is provided by IMS to upgrade the firmware of CPU.

PI-EDID Tools is for the interface between "Parallel Port of PC" and "15 pin-D-SUB

connector of Monitor".

It is a windows-based program, which cannot be run in MS-DOS.

System and equipment requirements

1. An Pentium (or above) personal computer or compatible.

2. Microsoft operation system Windows 95/98/2000/XP and Port95NT.exe.

3. EDID Software "QEDID.exe"

4. ISP boardas shown in Fig. 1

And I2C Board Jump wire should follow J10 (short), J9 (open), J5/J6/ (1and 2 pin short)

J7/J8 (1 and 2 pin short)

Connected to print cord and PC

Connected to Display Signal Cable

1 2

3 2

Fig.1

220V3 LCD 25

DDC Instructions

5. Connect and Mains cord to Monitor as shown in Fig.2.

Fig.2

Pin assignments :

A. 15-pin D-Sub Connector

B. Input DVI Connector pin

Pin Signal Assignment Pin Signal assignment

TMDS RX2-

13 Floating

2TMDS RX2+ 14 +5V Power

3 TMDS Ground 15

Self-test (Cable

detector) 4 Floating 16 Hot Plug Detect 5 Floating 17 TMDS RX06 DDC Clock 18 TMDS RX0+ 7 DDC Data 19 TMDS Ground 8 Floating 20 Floating 9TMDS RX1- 21 Floating

10 TMDS RX1+ 22 TMDS Ground 11 TMDS Ground 23 TMDS Clock+ 12 Floating 24 TMDS Clock-

PIN No. SIGNAL PIN No. SIGNAL

+ 58 hidden pages

Philips 220V3SB/00, 220V3SB/00(AP), 220V3AB/00, 220V3SB/93, 220V3AB/01 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual