Philips 201E1 User Manual

e-Manual

Philips LCD Monitor Electronic User’s Manual

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/INDEX.HTM2009-5-21 14:40:04

Safety and Troubleshooting Information

• Safety Precautions and
Maintenance

• FAQs

• Troubleshooting

• Regulatory Information

Safety and Troubleshooting Information

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than
those specified in this documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your computer monitor:
Operation:

● Keep the monitor out of direct sunlight and away from stoves or any other heat source.

● Remove any object that could fall into ventilation holes or prevent proper cooling of the

monitor’s electronics.

● Do not block the ventilation holes on the cabinet.

● When positioning the monitor, make sure the power plug and outlet are easily accessible.

● If turning off the monitor by detaching the power cable or DC power cord, wait for 6

seconds before attaching the power cable or DC power cord for normal operation.

● Please use approved power cord provided by Philips all the time. If your power cord is

missing, please contact with your local service center. (Please refer to Customer Care
Consumer Information Center)

● Do not subject the LCD monitor to severe vibration or high impact conditions during

operation.

● Do not knock or drop the monitor during operation or transportation.

Maintenance:

● To protect your display from possible damage, do not put excessive pressure on the LCD

panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by
placing your hand or fingers on the LCD panel.

● Unplug the monitor if you are not going to use it for an extensive period of time.

● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be

wiped with a dry cloth when the power is off. However, never use organic solvent, such
as, alcohol, or ammonia-based liquids to clean your monitor.

● To avoid the risk of shock or permanent damage to the set, do not expose the monitor to

dust, rain, water, or excessive moisture environment.

● If your monitor gets wet, wipe it with dry cloth as soon as possible.

● If foreign substance or water gets in your monitor, please turn the power off immediately

and disconnect the power cord. Then, remove the foreign substance or water, and send
it to the maintenance center.

● Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/safety.htm（第 1／2 页）2009-5-21 14:40:53

Safety and Troubleshooting Information

extreme cold.

● In order to maintain the best performance of your monitor and use it for a longer lifetime,

please use the monitor in a location that falls within the following temperature and
humidity ranges.

❍ Temperature: 0-40°C 32-95°F
❍ Humidity: 20-80% RH

● IMPORTANT: Always activate a moving screen saver program when you leave your

monitor unattended. Always activate a periodic screen refresh application if your LCD
monitor will display unchanging static content. Uninterrupted display of still or static
images over an extended period may cause “burn in”, also known as “after-imaging” or
“ghost imaging”, on your screen. "Burn-in", "after-imaging", or "ghost imaging" is a well­known phenomenon in LCD panel technology. In most cases, the “burned in” or “after­imaging” or “ghost imaging” will disappear gradually over a period of time after the power
has been switched off.

WARNING: Severe” burn-in” or “after-image” or “ghost image” symptoms will not

disappear and cannot be repaired. The damage mentioned above is not covered under
your warranty.

Service:

● The casing cover should be opened only by qualified service personnel.

● If there is any need for any document for repair or integration, please contact with your

local service center. (please refer to the chapter of "Consumer Information Center")

● For transportation information, please refer to "Physical Specifications".

● Do not leave your monitor in a car/trunk under direct sun light.

Consult a service technician if the monitor does not operate normally, or you are
not sure what procedure to take when the operating instructions given in this
manual have been followed.

RETURN TO TOP OF THE PAGE

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/safety.htm（第 2／2 页）2009-5-21 14:40:53

FAQs (Frequently Asked Questions)

• Safety and Troubleshooting

• General FAQs

• Compatibility with Other

Peripherals

• LCD Panel Technology

• Ergonomics, Ecology and

Safety Standards

• Troubleshooting

• Regulatory Information

FAQs (Frequently Asked Questions)

General FAQs

Q1:

When I install my monitor what should I do if the screen shows 'Cannot display this

video mode'?

A: Recommended resolution for Philips 20": 1600x900 @60Hz.

1. Unplug all cables, then connect your PC to the monitor that you used

previously.

2. In the Windows Start Menu, select Settings/Control Panel. In the Control Panel

Window, select the Display icon. Inside the Display Control Panel, select the
'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the
slidebar to 1600x900 pixels (20").

3. Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.

4. Restart your computer and repeat step 2 and 3 to verify that your PC is set at

1600x900@60Hz (20").

5. Shut down your computer, disconnect your old monitor and reconnect your

Philips LCD monitor.

6. Turn on your monitor and then turn on your PC.

Q2: What does the recommended refresh rate for LCD monitor?

A:Recommended refresh rate in LCD monitors is 60Hz, In case of any disturbance

on screen, you can set it up to 75Hz to see if that removes the disturbance.

Q3: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .

icm)?

A: These are the driver files for your monitor. Follow the instructions in your user

manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .
icm files) or a driver disk when you first install your monitor. Follow the instructions to
insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and .
icm files) will be installed automatically.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm（第 1／5 页）2009-5-21 14:41:00

FAQs (Frequently Asked Questions)

Q4: How do I adjust the resolution?

A: Your video card/graphic driver and monitor together determine the available

resolutions. You can select the desired resolution under Windows® Control Panel
with the "Display properties"

.

Q5: What if I get lost when I am making monitor adjustments?

A: Simply press the OK button, then select 'Reset' to recall all of the original factory

settings.

Q6: Will the LCD screen be resistant to scratches?

A: In general it is recommended that the panel surface is not subjected to excessive

shocks and is protected from sharp or blunt objects. When handling the monitor,
make sure that there is no pressure or force applied to the panel surface side. This
may affect your warranty conditions.

Q7: How should I clean the LCD surface?

A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use

isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,
hexane, etc.

Q8:Can I change the color setting of my monitor?

A:Yes, you can change your color setting through OSD control as the following

procedures,

1. Press "OK" to show the OSD (On Screen Display) menu

2. Press "Down Arrow" to select the option "Color" then press "OK" to enter color
setting, there are three settings as below.

a. Color Temperature; The 2 settings are 6500K,

.

9300K

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm（第 2／5 页）2009-5-21 14:41:00

FAQs (Frequently Asked Questions)

Q9: Can the Philips LCD Monitor be mounted on the wall?

A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount

holes on the rear cover allows the user to mount the Philips monitor on most of the
VESA standard arms or accessories. We recommend to contact your Philips sales
representative for more information.

RETURN TO TOP OF THE PAGE

Compatibility with other Peripherals

Q10:

Can I connect my LCD monitor to any PC, workstation or Mac?

A: Yes. All Philips LCD monitors are fully compatible with standard PCs, Macs and

workstations. You may need a cable adapter to connect the monitor to your Mac
system. Please contact your Philips sales representative for more information.

Q11: Are Philips LCD monitors Plug-and-Play?

A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP,

Vista and Linux.

b. sRGB; this is a standard setting for ensuring correct exchange of colors
between different device (e.g. digital cameras, monitors, printers, scanners,
etc)

c. User Define; the user can choose his/her preference color setting by
adjusting red, green blue color.

*A measurement of the color of light radiated by an object while it is being heated.
This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower
Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are
blue. Neutral temperature is white, at 6504K.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm（第 3／5 页）2009-5-21 14:41:00

FAQs (Frequently Asked Questions)

RETURN TO TOP OF THE PAGE

LCD Panel Technology

Q12:

What kind of wide-angle technology is available?

A: Currently, the IPS type panels offer the best Contrast Ratio, compared to MVA, or

PVA technologies. TN panels have improved over the years, but still cannot match
the Contrast Ratio offered by IPS panel.

RETURN TO TOP OF THE PAGE

Ergonomics, Ecology and Safety Standards

Q13:

What is Image Sticking, or Image Burn-in, or After Image, or Ghost Image in LCD

panels?

A: Uninterrupted display of still or static images over an extended period may cause

"burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn-in",
"after-imaging", or "ghost imaging" is a well-known phenomenon in LCD panel
technology. In most cases, the "burned in" or "atter-imaging" or "ghost imaging" will
disappear gradually over a period of time after the power has been switched off.

Always activate a moving screen saver program when you leave your monitor
unattended.

Always activate a periodic screen refresh application if your LCD monitor will display
unchanging static content.

WARNING: Severe"burn-in" or "after-image" or "ghost image" symptoms will not
disappear and cannot be repaired. The damage mentioned above is not covered
under your warranty.

Q14:

Why is my Display not showing sharp text, and is displaying jagged characters?

A: Your LCD monitor works best at its native resolution of 1600x900@60Hz. For best

display please use this resolution.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm（第 4／5 页）2009-5-21 14:41:00

FAQs (Frequently Asked Questions)

RETURN TO TOP OF THE PAGE

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_faq.htm（第 5／5 页）2009-5-21 14:41:00

Troubleshooting

● Make sure the monitor cable is properly connected to your

computer. (Also refer to the Quick Set-Up Guide).

● Check to see if the monitor cable has bent pins.

● Make sure the computer is turned on.

AUTO button doesn't function in VGA
mode

● The auto function is applicable only in VGA-Analog mode. If

the result is not satisfactory, you can do manual adjustments
via the OSD menu. Note that the Auto Function is not
applicable in DVI-Digital mode as it is not necessary.

Imaging Problems

Image is not centered

● Press the Auto button.

● Adjust the image position using the Phase/Clock of Setup in

OSD Main Controls.

Troubleshooting

• Safety and
Troubleshooting

• FAQs

• Common Problems

• Imaging Problems

• Regulatory Information

This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these
solutions, contact Philips customer service representative.

Common Problems

Having this problem Check these items

● Make sure the power cord is plugged into the power outlet

No Picture
(Power LED not lit)

No Picture

(Power LED is

orange)

and into the back of the monitor.

● First, ensure that the power button on the front of the monitor

is in the OFF position, then press it to the ON position.

● Make sure the computer is turned on.

● Make sure the signal cable is properly connected to your

computer.

● make sure the monitor cable has no bent pins on the connect

side. If yes, repair or replace the cable.

● The Energy Saving feature may be activated

Screen says

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_troub.htm（第 1／3 页）2009-5-21 14:41:12

Troubleshooting

Image vibrates on the screen

● Check that the signal cable is properly securely connected to

the graphics board or PC.

Vertical flicker appears

● Press the Auto button.

● Eliminate the vertical bars using the Phase/Clock of Setup in

OSD Main Controls.

Horizontal flicker appears

● Press the Auto button.

● Eliminate the vertical bars using the Phase/Clock of Setup in

OSD Main Controls.

image appears blurred, indistinct or too
dark

● Adjust the contrast and brightness on On-Screen Display.

An "after-image", "burn-in" or "ghost
image" remains after the power has
been turned off.

● Uninterrupted display of still or static images over an

extended period may cause " burn in", also known as "after­imaging " or "ghost imaging", on your screen. "Burn-in", "after­imaging", or "ghost imaging" is a well-known phenomenon in
LCD panel technology. In most cases, the "burned in" or
"after-imaging" or "ghost imaging" will disappear gradually
over a period of time after the power has been switched off.

● Always activate a moving screen saver program when you

leave your monitor unattended.

● Always activate a periodic screen refresh application if your

LCD monitor will display unchanging static content.

Image appears distorted. Text is fuzzy
or blurred.

● Set the PC’s display resolution to the same mode as

monitor’s recommended screen native resolution.

Green, red, blue, dark, and white dots
appears on the screen

● The remaining dots are normal characteristic of the liquid

crystal used in today’s technology, Pls refer the pixel policy

for more detail.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_troub.htm（第 2／3 页）2009-5-21 14:41:12

Troubleshooting

The "power on" light is too strong to
disturb me.

● You can adjust “power on” light using the power LED of Setup

in OSD main Controls.

For further assistance, refer to the Consumer Information Centers list and contact Philips customer service
representative.

RETURN TO TOP OF THE PAGE

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/saf_troub.htm（第 3／3 页）2009-5-21 14:41:12

Regulatory Information

• TCO'03 Information

•

TCO'06 Information

•

Recycling Information for Customers

•

Waste Electrical and Electronic
Equipment-WEEE

•

CE Declaration of Conformity

•

Energy Star Declaration

• Federal Communications
Commission (FCC) Notice (U.S.
Only)

•

FCC Declaration of Conformity

c Commission Federale de la

Communication (FCC Declaration)

• EN 55022 Compliance (Czech
Republic Only)

• Polish Center for Testing and
Certification Notice

• North Europe (Nordic Countries)
Information

• BSMI Notice (Taiwan Only)

•

Ergonomie Hinweis (nur
Deutschland)

• Philips End-of-Life Disposal

•

China RoHS

• Lead-free Product

• Troubleshooting

• Other Related Information

•

Frequently Asked Questions (FAQs)

Regulatory Information

Product name: 201E1
Model No: MWE1201T

TCO'03 Information

Congratulations!

The display you have just purchased carries the TCO'03 Displays label. This means
that your display is designed, manufactured and tested according to some of the
strictest quality and environmental requirements in the world. This makes for a high
performance product, designed with the user in focus that also minimizes the impact
on our natural environment.

*available for selective models

Some of the features of the TCO'03 Display requirements.

Ergonomics

● Good visual ergonomics and image quality in order to improve the working environment for the user and

to reduce sight and strain problems. Important parameters are luminance, contrast, resoluction,
reflectance, colour rendition and image stability.

Energy

● Energy-saving mode after a certain time-beneficial both for the user and the environment

● Electrical safety

Emissions

● Electromagnetic fields

● Noise emissions

Ecology

● The product must be prepared for recycling and the manufacturer must have a certified environmental

management system such as EMAS or ISO 14 000

● Restrictions on

❍ chlorinated and brominated flame retardants and polymers
❍ heavy metals such as cadmium, mercury and lead.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 1／11 页）2009-5-21 14:41:23

Regulatory Information

TCO'06 Information

Congratulations!

The product you have just purchased carries the TCO’06 Media Displays label. This
means that your display is designed and manufactured according to some of the
strictest performance and environmental criteria in the world. The manufacturer of
this display has selected it to be certified to TCO’06 Media Displays as a sign of
usability, high performance and reduced impact on the natural environment.

*available for selective models

Products certified to TCO´06 Media Displays are specifically designed for high quality reproduction of moving
images. Features such as luminance, color rendition and response time are important when watching TV or
working with media, graphics, web design and other applications that demand outstanding moving images. *

Other features of TCO’06 Media Displays:

Ergonomics

● Good visual ergonomics and image quality in order to reduce vision and strain problems. Criteria for

luminance, contrast, resolution, reflectance, color rendition and response time.

Energy

● Energy saving mode – beneficial both for the user and the environment

● Electrical safety

Emissions

● Low electromagnetic fields surrounding the display

Ecology

● Product is designed for recycling. Manufacturer must have a certified environmental management system

such as EMAS or ISO 14 001

● Restrictions on

❍ Chlorinated and brominated flame retardants and polymers.
❍ Hazardous heavy metals such as cadmium, mercury, hexavalent chromium and lead.

The requirements included in this label have been developed by TCO Development in co-operation with
scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been
involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system
started with displays in 1992 and is now requested by users and IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

RETURN TO TOP OF THE PAGE

Recycling Information for Customers

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 2／11 页）2009-5-21 14:41:23

Regulatory Information

Philips establishes technically and economically viable objectives to optimize the environmental performance of
the organization's product, service and activities.

From the planning, design and production stages, Philips emphasizes the important of making products that can
easily be recycled. At Philips, end-of-life management primarily entails participation in national take-back
initiatives and recycling programs whenever possible, preferably in cooperation with competitors.

There is currently a system of recycling up and running in the European countries, such as The Netherlands,
Belgium, Norway, Sweden and Denmark.

In U.S.A., Philips Consumer Electronics North America has contributed funds for the Electronic Industries
Alliance (EIA) Electronics Recycling Project and state recycling initiatives for end-of-life electronics products from
household sources. In addition, the Northeast Recycling Council (NERC) - a multi-state non-profit organization
focused on promoting recycling market development - plans to implement a recycling program.

In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA) to
follow the IT product recycling management process, detail can be found in web site www.epa.gov.tw

The monitor contains parts that could cause damage to the nature environment. Therefore, it is vital that the monitor is
recycled at the end of its life cycle.

For help and service, please contact Consumers Information Center or F1rst Choice Contact Information Center
in each country.

RETURN TO TOP OF THE PAGE

Waste Electrical and Electronic Equipment-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/
EC governing used electrical and electronic appliances, this product may not be disposed of with normal
household waste. You are responsible for disposal of this equipment through a designated waste electrical and
electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic,
contact your local government office, the waste disposal organization that serves your household or the store at
which you purchased the product.

Attention users in United States:

Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and
Federal laws. For the disposal or recyciing information, contact www.mygreenelectronics.com or www.eiae.org.

RETURN TO TOP OF THE PAGE

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 3／11 页）2009-5-21 14:41:23

Regulatory Information

EPEAT
“The EPEAT (Electronic Product Environmental Assessment Tool) program evaluates computer desktops,
laptops, and monitors based on 51 environmental criteria developed through an extensive stakeholder
consensus process supported by US EPA.
EPEAT system helps purchasers in the public and private sectors evaluate, compare and select desktop
computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and
consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers
to secure market recognition for efforts to reduce the environmental impact of its products.”

Benefits of EPEAT
Reduce use of primary materials
Reduce use of toxic materials
Avoid the disposal of hazardous waste
EPEAT’S requirement that all registered products meet ENERGY STAR’s energy efficiency specifications,
means that these products will consume less energy throughout their life.

RETURN TO TOP OF THE PAGE

ROHS is a European Directive aiming to control the use of certain hazardous substances in the production of
new electrical and electronic equipment. Philips has completely eliminated four of six RoHS-banned substances
form its products by 1998-eight full years before compliance was required and has lowered usage of the
remaining substances significantly below the mandated levels.

RETURN TO TOP OF THE PAGE

CE Declaration of Conformity

Philips Consumer Electronics declare under our responsibility that the product is in conformity with the following
standards

- EN60950-1:2001 (Safety requirement of Information Technology Equipment)

- EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)

- EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)

- EN61000-3-2:2000 or EN61000-3-2:2006(Limits for Harmonic Current Emission)

- EN61000-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable

- 73/23/EEC (Low Voltage Directive)

- 2004/108/EC(EMC Directive)

- 2006/95/EC (Low Voltage Directive)
and is produced by a manufacturing organization on ISO9000 level.

The product also comply with the following standards

- ISO13406-2 (Ergonomic requirement for Flat Panel Display)

- GS EK1-2000 (GS specification)

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 4／11 页）2009-5-21 14:41:23

Regulatory Information

- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)

- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)

- TCO'03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish
Confederation of Professional Employees) for TCO versions

RETURN TO TOP OF THE PAGE

As an ENERGY STAR

®

Partner, PHILIPS has determined that this product meets

the

ENERGY STAR® guidelines for energy efficiency.

We recommend you switch off the monitor when it is not in use for a long time.

RETURN TO TOP OF THE PAGE

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Energy Star Declaration

This monitor is equipped with a function for saving energy which supports the VESA DPM
standard. This means that the monitor must be connected to a computer which supports VESA
DPM. Time settings are adjusted from the system unit by software.

Normal operation ON (Active) Green <

VESA State LED Indicator Power Consumption

24.5W (typ.)

Power Saving
Alternative 2
One step

Sleep

Orange < 0.8 W (typ.)

Switch Off Off < 0.5 W (typ.)

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 5／11 页）2009-5-21 14:41:23

Regulatory Information

● Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer
device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive
moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE­CAUSING EQUIPMENT REGULATIONS.

RETURN TO TOP OF THE PAGE

FCC Declaration of Conformity

Trade Name: Philips

Responsible Party:

Philips Consumer Electronics North America
P.O. Box 671539
Marietta , GA 30006-0026
1-888-PHILIPS (744-5477)

Declaration of Conformity for Products Marked with FCC Logo,
United States Only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.

RETURN TO TOP OF THE PAGE

Commission Federale de la Communication (FCC Declaration)

Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de
class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon
à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une
installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences
qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer
des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir
l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la
cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce
qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 6／11 页）2009-5-21 14:41:23

Regulatory Information

pourrait essayer de corriger la situation en prenant les mesures suivantes:

● Réorienter ou déplacer l'antenne de réception.

● Augmenter la distance entre l'équipement et le récepteur.

● Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.

● Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.

Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de
conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.

N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.

CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU REGLEMENT
SUR LE MATERIEL BROUILLEUR DU CANADA.

RETURN TO TOP OF THE PAGE

EN 55022 Compliance (Czech Republic Only)

RETURN TO TOP OF THE PAGE

Polish Center for Testing and Certification Notice

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All
equipment that works together (computer, monitor, printer, and so on) should have the same power supply
source.

The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in
the form of a fuse with a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket,
which should be located near the equipment and easily accessible.

A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of
standards PN-93/T-42107 and PN-89/E-06251.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 7／11 页）2009-5-21 14:41:23

Regulatory Information

RETURN TO TOP OF THE PAGE

North Europe (Nordic Countries) Information

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR
DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT
ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI
IRROTTAA PISTORASIASTA.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 8／11 页）2009-5-21 14:41:23

Regulatory Information

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR
STØMTILFØRSEL ER LETTE Å NÅ.

RETURN TO TOP OF THE PAGE

BSMI Notice (Taiwan Only)

RETURN TO TOP OF THE PAGE

Ergonomie Hinweis (nur Deutschland)

Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch
Röntgenstrahlen" festgelegten Vorschriften.

Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme
hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der
Röntgenverordnung erfüllt sind.

Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß

1. Reparaturen nur durch Fachpersonal durchgeführt werden.

2. nur original-Ersatzteile verwendet werden.

3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.

Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem
Zeichenkontrast wären die Folge).

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.

ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.

RETURN TO TOP OF THE PAGE

End-of-Life Disposal

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 9／11 页）2009-5-21 14:41:23

Regulatory Information

Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your
product to increase the amount of reusable materials and to minimize the amount to be disposed of.

Please find out about the local regulations on how to dispose of your old monitor from your sales representative.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative)

RETURN TO TOP OF THE PAGE

China RoHS

The People's Republic of China released a regulation called "Management Methods for Controlling Pollution by
Electronic Information Products" or commonly referred to as China RoHS. All products including CRT and LCD
monitor which are produced and sold for China market have to meet China RoHS request.

环保使用期限

此标识指期限(十年),电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外泄或突

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 10／11 页）2009-5-21 14:41:23

Regulatory Information

变, 电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、 财产造成严重损害的期
限．

RETURN TO TOP OF THE PAGE

Lead-free Product

Philips eliminated toxic substances like lead from its displays. Lead-free display helps protect your
health and promotes environmentally sound recovery and disposal of waste from electrical and
electronic equipment.Philips complies with the European Community stringent RoHS Directive
mandating restrictions on hazardous substances in electrical and electronic equipment. With
Philips, you can be confident that your display device does not harm the environment.

RETURN TO TOP OF THE PAGE

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/safety/regs/regulat.htm（第 11／11 页）2009-5-21 14:41:23

About This Manual

• About This Guide

• Notational Descriptions

About This Manual

About This Guide

This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It
describes the LCD monitor's features, setup, operation and other important information. Its
contents are identical to the information in our printed version.

It includes the following sections:

● Safety and Troubleshooting Information provides tips and solutions for common problems

as well as other related information you may need.

● About This Electronic User's Manual gives an overview of information included, along with

notation icon descriptions and other documentation for your reference.

● Product Information gives an overview of the monitor's features as well as the technical

specifications for this monitor.

● Installing Your Monitor describes the initial setup process and gives an overview of how to

use the monitor.

● On-Screen Display provides information on adjusting the settings on your monitor.

● Customer Care and Warranty contains a list of worldwide Philips Consumer Information

Centers along with help desk phone numbers and information on the warranty applicable
to your product.

● Glossary defines technical terms.

● Download and Print Option transfers this entire manual to your hard drive for easy

reference.

RETURN TO TOP OF THE PAGE

Notational Descriptions

The following subsections describe notational conventions used in this document.

Notes, Cautions and Warnings

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/about/about.htm（第 1／2 页）2009-5-21 14:41:34

About This Manual

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic
type. These blocks contain notes, cautions or warnings. They are used as follows:

NOTE: This icon indicates important information and tips that help you make
better use of your computer system.

CAUTION: This icon indicates information that tells you how to avoid either
potential damage to hardware or loss of data.

WARNING: This icon indicates the potential for bodily harm and tells you how
to avoid the problem.

Some warnings may appear in alternate formats and may not be accompanied by an icon. In
such cases, the specific presentation of the warning is mandated by the relevant regulatory
authority.

RETURN TO TOP OF THE PAGE

©2009 Koninklijke Philips Electronics NV

All rights reserved. Reproduction, copying, use, modification, hiring, renting, public performance, transmission and/or
broadcasting in whole or in part is prohibited without written consent of Philips Electronics NV

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/about/about.htm（第 2／2 页）2009-5-21 14:41:34

Product Information

• Your LCD Monitor

• Smartimage

• SmartContrast

• SmartSaturate

• SmartSharpness

• Technical Specifications

• Resolution & Preset Modes

• Philips Pixel Defect Policy

• Automatic Power Saving

• Product Views

• Physical Function

• SmartControl II

Product Information

Your LCD monitor

Congratulations on your purchase and welcome to Philips. To fully benefit from the support that Philips offers, register
your product at. www.philips.com/welcome

SmartContrast

What is it?

Unique technology that dynamically analyzes displayed content and automatically optimizes a LCD monitor's contrast
ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter
images or dimming backlighting for clear display of images on dark backgrounds.

Why do I need it?

You want the very best visual clarity and viewing comfort for every type of content. SmartContrast dynamically controls
contrast and adjusts backlighting for clear, crisp, bright gaming and video images or displays clear, readable text for
office work. By reducing your monitor's power consumption, you save on energy costs and extend the lifetime of your
monitor.

How does it work?

When you active SmartContrast which will analysis the content you are displaying in real time to adjust colors and
control backlight intensity. This function can obviously enhance contrast in dynamic for more entertainment fun when
viewing videos or playing games.

RETURN TO TOP OF THE PAGE

Technical Specifications*

Picture/Display

• LCD panel type TFT-LCD

• Panel size 20"

• Aspect ratio 16:9

• Pixel Pitch 0.2768 x 0.2768 mm

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm（第 1／6 页）2009-5-21 14:42:04

Product Information

• Brightness

250 cd/m²

•SmartContrast 25000:1

•Contrast ratio(typ.) 1000:1

• Response time (typical) 5 ms

• Optimum Resolution 1600 x 900 @ 60Hz

• Viewing angle 1

60° (H) / 160° (V) @ C/R > 10

• Display colors 16.7 M

• Scanning Frequency 30 - 83 kHz (H)/56 -75Hz (V)

• sRGB YES

Connectivity

• Signal input DVI-D (digital, HDCP), VGA (Analog)

• Input Signal Separate Sync, Sync on Green

Convenience

• User Convenience Auto(Back), 4:3/Wide(Down), Brightness(Up), Menu(OK), Power On/Off

• OSD Languages

English, French, German, Italian, Russian, Spanish, Simplified Chinese,
Portuguese, Turkish

• Other convenience VESA mount ( 100 x 100mm), Kensington lock

• Plug & Play Compatibility DDC/CI, sRGB, Windows 98/2000/XP/Vista, Mac OS X

Stand

• Tilt -5/+20

Power

• On mode (typcial) < 24.5 W
Energy Consumption

(EnergyStar 5.0 test method)
Normal Operation

Sleep 0.8 W 0.8 W 0.8 W
Off 0.5 W 0.5 W 0.5 W

Heat Dissipation*

Normal Operation
Sleep 2.7BTU/hr 2.7BTU/hr 2.7BTU/hr

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm（第 2／6 页）2009-5-21 14:42:04

20.5W 20.4 W 20.3 W

70.0BTU/hr 69.6BTU/hr 69.3BTU/hr

AC Input Voltage at
100VAC +/-5VAC,
50Hz +/- 3Hz

AC Input Voltage at
100VAC +/-5VAC,
50Hz +/ -3Hz

AC Input Voltage at
115VAC +/-5VAC,
60Hz +/- 3Hz

AC Input Voltage at
115VAC +/-5VAC,
60Hz +/ -3Hz

AC Input Voltage at
230VAC +/-5VAC, 50Hz
+/ -3Hz

AC Input Voltage at
230VAC +/-5VAC, 50Hz
+/ -3Hz

Product Information

Off 1.7BTU/hr 1.7BTU/hr 1.7BTU/hr

• Power LED indicator On mode:

• Power Supply Build-in, 100-240VAC, 50/60Hz

Dimension

• Product with stand ( WxHxD) 478.94 x 353.45 x 189.81mm

• Product without stand
( WxHxD)

• Box dimension ( WxHxD)

4

78.94 x 290.6 x 61.43mm
555 x 354 x 140mm

Green, Standby/Sleep mode: orange

Weight

• Product with stand 3.97kg

• Product without stand 3.

• Product with packaging

69kg

5.85kg

Operating Condition

• Temperature range (operation) 0° C to 40 ° C

• Temperature range (operation) -20° C to 60° C

• Relative humidity 20% to 80%

• Altitude

• MTBF 50000 hrs

Non-operation: + 12,000 ft ( 3,658 m)
operation: + 40,000 ft ( 12,192 m),

Environmental

• ROHS YES

• EPEAT sliver

• EnergyStar 5.0

• Packaging 100% recyclable

Compliance and standards

• Regulatory Approvals

CE Mark, Energy Star 5.0, FCC Class B, SEMKO

Cabinet

• Color Black/Black

• Finish Glossy

* This data is subject to change without notice.

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm（第 3／6 页）2009-5-21 14:42:04

RETURN TO TOP OF THE PAGE

Product Information

Automatic Power Saving

If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce
its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the
monitor will 'wake up' automatically. The following table shows the power consumption and signaling of this automatic
power saving feature:

Power Management Definition

Resolution & Preset Modes

A.

Maximum Resolution

- For 201E1
1600 x 900 at 75 Hz (analog input)

1600 x 900 at 75 Hz (digital input)

B. Recommended Resolution

- For 201E1
1600 x 900 at 60 Hz (digital input)
1600 x 900 at 60 Hz (analog input)

12 factory preset modes:

H. freq (kHz) Resolution V. freq (Hz)

31.47 720*400 70.09

31.47 640*480 59.94

37.50 640*480 75.00

37.88 800*600 60.32

46.88 800*600 75.00

48.36 1024*768 60.00

60.02 1024*768 75.03

44.77 1280*720 59.86
4

8.70 1280*800 59.81

63.89 1280*1024 60.02

79.98 1280*1024 75.03

60.00 1600*900 60.00

file:///G|/201E1/201E1/lcd/manual/ENGLISH/201E1/product/product.htm（第 4／6 页）2009-5-21 14:42:04

RETURN TO TOP OF THE PAGE