Philips 14PV182-58 User Manual

Download

Page 1

OPERATING INSTRUCTIONS IN BRIEF

The remote control

RECORD n

STANDBY m

SV/V+

TIMER k

CLEAR b

0-9

STOP h

GPLAY

P p

MUTE y

INDEX E

STILL R

CLEAR b

Record

Standby

’SHOWVIEW’ programming

TIMER programming on the set

Reset/clear

Digit buttons 0-9

Pause/Stop

Playback

Menu left

Menu right

Volume control

menu Up

menu Down

Programme number Plus/Minus

Mute sound

Call menu

Confirm button

Index search

Still picture

The following buttons are only available for some sets:

TELETEXT concealed information

TELETEXT off (temporarily)

TELETEXT on/off

TELETEXT page stop

TELETEXT enlarged print

Front of the set

P p

Standby

Programme number Plus/Minus

Volume control

Record

Rewind/Reverse scanning

Pause/Stop

Playback

Forward wind/ Forward scanning

Cassette eject

Headphones socket

Page 2

Programming with ’SHOWVIEW’

All the information required for programming is encoded in the ’SHOWVIEW’ code.

1 Press the 2 Enter the entire ’SHOWVIEW code’. This code (up to 9 digits) is found next to the start time of

a TV programme in your TV guide. If you entered an incorrect code number, clear it with the

3 If you want to repeat programming at daily or weekly intervals, select the required settings in

the ’DAILY/WEEKLY’ line. ’Daily’ programming can only be used for recordings to be made from Mondays to Fridays inclusive.

4 After confirming the corresponding data appears on the TV screen.

Note: If you use SHOWVIEW for the first time, the ’PROGRAMME NR.’ line appears when you enter the SHOWVIEW code. Enter the required programme number for this channel.

Confirm with the

The data has been stored in a TIMER block. Please ensure that you loaded a cassette without erase protection.

6 Press the

SV/V+

button on the remote control.

DATE DW PR START END c

01 01 17:15 18:45

vw 0-9 OK

button.

STANDBY m

button.

CLEAR b

button.

How to enter, check or clear a TIMER-block manually

1 Press the 2 Select a free TIMER block or the TIMER block you want to check or clear. 3 Clear: Press the 4 Enter/Check: Press the

weekly), ’PR’ (programme number), ’START’ (start time) and ’END’ (end time). Press the

5 To end programming, press the 6 Press the

TIMER k

and the

STANDBY m

button.

CLEAR b

DorC

button.

button to switch between ’DATE’ (date), ’DW’ (daily,

or the

0-9

buttons to change the data.

button.

Selecting a TV channel

Select the required TV channel (= programme number) with the

P p

button or the buttons on the remote control. The selected programme number (e.g.: ’P 01’) appears in the upper right corner of the TV screen.

0-9

Volume control

You can control the volume level with the If you want to mute the sound temporarily (e.g.: during a telephone call), press the button on the remote control. When you press it again, the sound returns at the same volume level.

button.

MUTE y

Picture control

You can control brightness, contrast, sharpness and colour here.

1 Press the 2 Select and confirm the line ’PICTURE’. 3 Select and confirm the TV screen setting.

button.

* In addition, you can adjust the tint for the playback of cassettes in the NTSC standard.

Page 3

OPERATING INSTRUCTIONS PHILIPS 14PV182/58

Congratulations on the purchase of one of the most sophisti-

cated and simple-to-use television/video recorders combinations (TV combi) on the market. With this TV combi you can record and play VHS-standard cassettes.

Please take the time to read this operating manual before using your TV combi.

Safety instructions and other notes

• Danger: high voltage! Do not open the set. The set does not contain any components that can be repaired by the customer. When the appliance is connected to the power supply there are some components that are constantly operational. To switch off the set completely you must disconnect it from the power supply.

• Note that this power pack is designed for a power supply of 220-240V/50Hz.

• Ensure that air can circulate freely through the ventilation slots on the set.

• Ensure that no objects or liquids enter the set. If liquid is spilt into it, disconnect the set immediately from the power supply and call the After-sales Service for advice.

• The set should not be used immediately after transportation from a cold to a hot area or vice versa, or in conditions of extreme humidity. After unpacking the set, it should be allowed to acclimatize for at least three hours before installation.

• These operating instructions have been printed on nonpolluting paper.

• Deposit old batteries at the relevant collection points.

• Please make use of the facilities available in your country for

disposing of the packaging of the set in a way that helps to protect the environment.

• This electronic equipment contains many materials that can be recycled. Please inquire about the possibilities for recycling your old set.

• SHOWVIEW is a trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under licence from Gemstar Development Corporation.

Contents Page

1. INSTALLATION 2................................

Connecting additional equipment 2..................

Emergency interrupt 2............................

User guide 2....................................

Making standard settings 3........................

Setting the clock and date 3.......................

2. PLAY BACK 4...................................

Continuous playback 4...........................

3. RECORD 5......................................

Programming with ’SHOWVIEW’ 6..................

4. SPECIAL FEATURES 7............................

On Screen Display (OSD) 7........................

Sleep function (switch off) 7.......................

Switch set on function 7..........................

Child lock 8.....................................

Before you call an engineer 9......................

Page 4

1. INSTALLATION

Connecting the cables

1 Insert the aerial plug into the

If you use the auxiliary aerial supplied, push the aerial into the mounting on the back panel until it snaps into place. Pull out the telescopic rod(s) as far as required. Tilt and rotate the aerial until you have got the best picture quality.

2 Insert the plug of the mains cable into the wall socket. 3 Switch the set on. The power switch

the left side panel of the set.

socket.

is located on

Connecting additional equipment

You can also connect additional equipment to the

EXTERNAL

socket, for instance, a decoder satellite receiver

or camcorder.

Emergency interrupt

Both the set and the remote control have an ’Emergency interrupt’ button. You can use the

STANDBY m

button to interrupt any function. Whenever you have operating problems you can simply interrupt the function and start again. You can practise operating your set without any worries. No matter which buttons you press, you cannot damage it.

User guide

Important notes for operation

• We advise you, from now on, to switch the set to standby using the on the remote control.

• When the set is in the standby mode, a small red lamp on the left of the front of the set will be alight.

• You can switch on with the

0-9

• Attention: When you use the power switch side panel, you have completely switched off the set from the mains power supply. No programmed recordings will then be made. The red lamp on the left of the front of the set will not be alight. After a few hours, the date and clock settings will be lost.

• Attention: Before you switch off the appliance with the power switch

• Keep your TV Combi connected to the mains and the power switch in ’on’ position at all times to ensure that programmed recordings can be made and that the television functions normally. The power consumption required is low.

• Back-up power supply: TV channel storage - typically 1 year, Clock/Timer - typically 7 hours.

STANDBY m

button on the front of the set or

STOP h

buttons or by inserting a cassette.

, remove the tape by pressing the

button.

button, the

on the

With OSD (On Screen Display) the corresponding functions appear on the TV-screen. The most important button-functions are displayed at the bottom of the screen. Throughout this instruction manual, use the following buttons for the functions ’Call up’, ’Select’, ’Enter’/’Adjust’, ’Confirm’ and ’Exit’:

• Call up: Use the

• Select: Select a line with the

0-9

the

buttons or the

button.

menue button

button. Use

to select within a line.

• Enter/Alter: With the

or with the

0-9

button.

• Confirm: With the

• Exit: With the

Page 5

Making standard settings

1 To start, press the

button and the

INSTALLATION vw

LANGUAGE EN COUNTRY UK AUTO STORE MANUAL STORE SORT PP STORE

STOP h

button simultaneously.

button. Press the

2 Select the required display language in the ’LANGUAGE’

line.

3 Select your country in the ’COUNTRY’ line.

3 Wait until all TV channels have been stored.

All TV channels will be stored from programme number 69 downward.

How you can search for a TV channel manually, you can read in chapter 4 ’SPECIAL FEATURES’ in the section ’Manual channel search’.

Note:

* If the ’Automatic channel search’ function is activated, any previously programmed TIMER blocks will be cleared.

You can store up to 69 TV channels.

Allocating channel numbers

Setting the clock and date

1 To start, press the 2 Press the

3 Select and confirm the line ’FEATURES’. 4 Select and confirm the line ’SET CLOCK’.

SET CLOCK

TIME 20:00 YEAR 1998 MONTH 01 DATE 01

xy 0-9

5 Enter the time, year, month and date.

STOP h

button.

Automatic Channel Search

1 Switch on with the

button and the

STOP h

button simultaniously.

button. Press the

1 Switch on with the

button and the

STOP h

button simultaneously.

button. Press the

2 Select and confirm the line ’SORT’.

SORT vw

FROM P01 TO P02 STORE

C-21

3 On the TV screen, in the line ’FROM’, select the TV

channel to which you want to allocate a programme number, e.g.: ’P 01’.

4 In the line ’TO’, select the required programme number,

e.g.: ’P 02’.

5 Select and confirm the line ’STORE’.

The allocated TV channels will be exchanged.

6 Repeat steps 3to 5until you have allocated a pro-

gramme number to all the required TV channels.

To finish, press the

button twice.

2 Select and confirm the line ’AUTO STORE’.

The ’Automatic Channel Search’ function starts.

AUTO STORE

PRESS xyTO STOP

SEARCH PLEASE WAIT

CHANNELS FOUND: 1

aaabbbbbbbbbbbbbbbbb

Page 6

2. PLAY BACK

1 Insert a cassette into the cassette slot.

2 Press the

3 Picture search: Now press the

GPLAY

play back button.

(rewind) or

(wind) button once or several times.

4 Interrupt: Press the

5 Wind: Stop the tape and press the

(wind) button.

6 Eject: Press the

STOP h

button on the set.

button.

(rewind) or the

Note: Some functions switch off automatically after a while (e.g.: Pause, Still Picture, Scanning). This helps to protect the cassette and prevent unnecessary power consumption. * With this set you can play back cassettes that have been recorded on another TV combi in the NTSC standard. * If you load a cassette with erase protection, the TV combi starts the play back automatically. * The picture quality is affected during scanning. The sound is switched off. * Remove the cassette before transporting the TV Combi.

Tape position/Index search

Tape position: If you press the

will be shown in the display during Wind, Rewind, Record, Play back and Pause/Stop.

Index search: Every time you start to record, the tape is marked with a code mark.

1 Press the

INDEX E

button. Press the select the next code mark or the previous code mark.

2 Once the TV Combi finds the code mark or unrecorded

area it will automatically switch to play back.

Note: When you press any tape transport button (e.g.: the

button) this search function will be stopped. * You cannot use this function with recordings made on another video recorder that does not have this function.

button the tape position

button to

button for the

Eliminating picture interference

1 During playback press the

button.

Still picture

1 Press the

Interference stripes will appear. Each time you press the ture will move on one step.

STILL R

button. You see a still picture.

STILL R

button again the pic-

Continuous playback

1 Press the

2 Select and confirm the ’SPECIAL’ line.

3 Select the ’REPEAT PLAY’ line. Switch on the continuous

playback.

4 Press the

5 Start the continuous playback with the

button.

6 If you want to cancel the function, stop the continous

playback in the ’REPEAT PLAY’ line.

button.

GPLAY

playback

2 Select and confirm the ’SPECIAL’ line.

3 Select the ’TRACKING’ line.

4 Press the

button until the playback

quality is at its best.

5 Press the

button. This setting will remain until

you remove the cassette.

6 Cleaning function: Press the

7 Select and confirm the ’SPECIAL’ line.

8 Select the ’CLEANING’ line.

9 Press the

button. A blue screen appears for a few

button.

seconds.

0 Wait until the blue screen disappears and press the

button.

Note: * Some hired cassettes may have a poor picture/sound quality. This is not a fault in your set.

Page 7

3. RECORD

1 Insert a cassette.

2 Use the

P p

button to select the programme number

from which you wish to record, e.g.: ’P 01’.

3 Press the

4 Use the

5 If, whilst recording, you want to switch off the TV screen,

press the To switch the TV screen on again, press the

RECORD n

STOP h

STANDBY m

button.

button to stop the recording.

button once.

P p

button.

Important notes for recoding

• OTR: If you do not want to record to the end of the

or the

RECORD n

EXTERNAL

button again. The display

button you can change the

CLEAR b

scart socket).

STOP h

button. ’PAUSE’

cassette, press the shows at what time the recording will stop. With the

end time of the recording in 30 minute intervals. If you wish to cancel the end time, press the button.The recording goes on uninterruptedly. (This does not effect the recording.)

• Programme number ’E1’ is provided for recording from external sources (via the

• Erase protection: So that you don’t accidentally delete an important recording, you can remove the special tab (erase protection) on the narrow side of the cassette with a screwdriver or slide the special tab to the left. Later, if you no longer want the cassette to be erase protected, you can seal the gap again with adhesive tape or slide the special tab to the right.

• Auto-assembling: You can use the auto-assembling func- tion to join individual recordings without any major picture disturbance between the recordings. Search for the correct position on the tape and then stop the playback by pressing the appears in the display. Now start recording as usual by pressing the

RECORD n

button.

Programme a recording

The set needs the following information for every programmed recording:

* the date on which the recording is to be made * the programme number for the TV channel * the start and end time of the recording * VPS on or off

The set stores all the information mentioned above in what is known as a TIMER block. It can store 6 TIMER blocks for up to one month in advance.

’VPS’ (Video Programming System)

With VPS, the TV station controls the start and the duration of a programmed recording. This means that the video recorder switches itself on and off at the right time even if a TV programme you have programmed begins earlier or finishes later than expected. Usually the start time is the same as the VPS time. If, however, a different VPS time code is given, e.g.: ’20.15 (VPS

20.14)’, you have to enter ’20.14’ (the VPS time) exactly to the minute. If you are not using VPS, the ’VPS’ indication must be off.

Page 8

Programming with ’SHOWVIEW’

All the information required for programming is encoded in the ’SHOWVIEW’ code.

1 Press the

2 Enter the entire ’SHOWVIEW code’. This code (up to 9

digits) is found next to the start time of a TV programme in your TV guide. If you entered an incorrect code number, clear it with the

CLEAR b

SV/V+

button on the remote control.

button.

SHOWVIEW

CODE 53124---DAILY/WEEKLY ONCE PROGRAMME NR. 01

How to enter, check or clear a TIMER block manually

1 Press the

2 Select a free TIMER block or the TIMER block you want

to check or clear.

3 Clear: Press the

4 Enter/Check: Press the

between ’DATE’ (date), ’DW’ (daily, weekly), ’PR’ (programme number), ’START’ (start time) and ’END’ (end time). Press the change the data.

TIMER k

and the

button.

CLEAR b

button.

, or the

button to switch

0-9

buttons to

xy 0-9 OK

3 If you want to repeat programming at daily or weekly

intervals, select the required setting in the ’DAILY/WEEKLY’ line. ’Daily’ programming can only be used for recordings to be made from Mondays to Fridays inclusive.

4 After the confirmation the corresponding data appear on

the TV screen.

Note: If you use SHOWVIEW for the first time, the ’PROGRAMME NR.’ line appears when you enter the SHOWVIEW code. Enter the required programme number for this TV channel.

DATE DW PR START END c

01 01 17:15 18:45

vw 0-9 OK

5 Confirm with the

button.

The data has been stored in a TIMER block. Please ensure that you loaded a cassette without erase protection.

5 To end programming, press the

6 Press the

STANDBY m

button.

Important notes for programmed recordings

• If the message ’PLEASE PRESS STOP’ or ’PLEASE PRESS STANDBY’ appears on the TV screen, press the

STOP h

or the A TIMER recording will function only, if the set isn’t used for other video recorder functions (e.g.: playback).

• The TIMER lamp on the front of the set lights up when one or more of the TIMER blocks are occupied.

• If the end of the cassette is reached during a recording, the video recorder automatically ejects the cassette. The set switches off after a few minutes.

• If you forget to load a cassette, ’NO CASSETTE CANNOT RECORD’ will appear.

• If you inserted a cassette with erase protection when you want to start a recording, the cassette will be ejected.

• If ’CODE ERROR’ appears on the TV screen, you entered an incorrect code number or the incorrect date. Repeat the entry or end with the With ’Daily’ programming, the first recording must take place within a week.

• If ’DAILY ERROR’ appears on the TV screen, the date was incorrectly entered. ’Daily’ programming can only be used for recordings to be made from Mondays to Fridays inclusive.

STANDBY m

button.

6 Press the

STANDBY m

button.

Page 9

4. SPECIAL FEATURES

On Screen Display (OSD)

You can switch OSD on or off.

1 Press the

2 Select and confirm the ’FEATURES’ line.

3 Select the ’DISPLAY’ line.

4 Select one of the options indicated.

’FULL’: OSD appears for a few seconds each time an operating mode is selected and then disappears. ’OFF’: OSD is switched off. ’PROG’: only the programm number appears. ’COUNT’: only the counter appears.

button.

FEATURES vw

PP RECALL ON TIMER SLEEPTIMER 0 DISPLAY FULL CHILD LOCK OFF SET CLOCK

5 Select and confirm the ’FEATURES’ line.

6 Select and confirm the ’PP RECALL’ line.

7 Press the

button. The set will use this setting.

Sleep function (switch off)

You can programme your set to switch off after a predetermined period.

1 Press the

2 Select and confirm the ’FEATURES’ line.

3 Select ’SLEEPTIMER’ line.

4 With the

the minutes left until switch off in 15 minutes intervals. When you set the time to ’0’ with the the sleep function is switched off.

5 Press the

button.

or the

button.

button you can determine

CLEAR b

button

5 Confirm it with the

Note: With the

button.

button you can superimpose the

actual operating mode on the TV screen.

Personal Preset

You can make your personal picture and volume settings here. You can call up this setting and it will be used automatically when you switch the set on.

1 select your personal setting. (see chapter ’The TV set

functions’). Press the

button and the

simultaniously.

2 Select and confirm the ’PP STORE’ line.

3 To end press the

button. The personal setting

has been stored.

button

Switch set on function

You can programme your set to switch on at a predetermined time.

1 Press the

2 Select and confirm the ’FEATURES’ line.

3 Select and confirm the ’ON TIMER’ line.

4 Determine the time you wish the set to switch on.

5 Select the ’WAKE UP’ line and switch the ’on-timer’ on or

off.

6 Press the

button.

4 Calling up your Preset: Press the

button.

Page 10

Child lock

Manual channel search

1 Press the

2 Select and confirm the ’FEATURES’ line.

3 Select the ’CHILD LOCK’ line.

4 Switch the child lock on or off.

5 Press the

button.

Note: If a button is pressed with the childlock ’on’, ’CHILD LOCK’ appears for a few seconds in the display. * Programmed recordings are made despite the child lock and cannot be interrupted.

In certain cases the Automatic Channel Search may not be able to find all of the TV channels (e.g.: coded TV channels). You can then use this manual method to set the channels.

1 Switch on the set with the

button and the

2 Select and confirm the ’MANUAL STORE’ line.

MANUAL STORE vw

CHANNEL/FREQ. SYSTEM EUR SEARCH C-21 FINE TUNING PROGRAMME NR. 1 DECODER STORE

3 Select the ’SEARCH’ line.

4 Press the

button as often as necessary, until you

STOP h

button simultaniously.

button. Press the

have found the right TV channel.

Note: * If you want to allocate a decoder, switch the decoder function on or off with the

button in the ’DECODER’ line. * If you want to change the automatic channel setting, select the ’FINE TUNING’ line. With the

button you can vary the auto-

matic TV channel setting.

Important: This re-tuning is only necessary and useful in special cases, e.g.: when there are stripes on the

picture with cable-TV systems.

5 In the ’PROGRAMME NR.’ line use the

P p

button to

select the required programme number, e.g.: ’P 01’.

6 Select and confirm the ’STORE’ line.

7 If you want to search for further TV channels, start again

at step 4. To finish, press the

button twice.

Page 11

Before you call an engineer

If, contrary to expectation, you experience any difficulty in operating this TV Combi, please call the customer service in your country. You will find the telephone numbers in the enclosed guarantee leaflet.

The set does not respond to any button being pressed:

• No power supply.

• Technical disturbance: disconnect from the mains for 30

seconds, then re-connect.

• The power switch on the side panel is switched off.

• Child lock is active.

Cassette jammed:

• Don’t use force. Pull out the mains plug for a moment.

Remote control does not operate:

• Remote control wasn’t pointed at the set.

• Batteries are exhausted.

No playback on TV Combi:

• No recording on the cassette.

No TV reception:

• The aerial is not connected.

• No TV channels have been stored.

Poor playback from TV combi:

• Cassette badly worn or of poor quality.

• Use the ’TRACKING’ function.

No recording possible:

• TV channel not stored or wrongly selected.

• Cassette with erase protection has been loaded.

Programmed recording does not function:

• TIMER not set properly.

• Time data wrongly programmed.

• A cassette with erase protection has been loaded.

• VPS switched on but ’VPS time’ wrong. Check aerial.

This product complies with the requirements of the Directive 73/23/EEC + 89/336/EEC + 93/68/EEC.

TYPE 14PV182/58

VNxx SER.NR......

Page 12

Page 13

Page 14

3103 166 20311

8135/003

(WwnnNNNwwnwNNnwnWwnNNNwwnWnnnW)

14PV182/58