Copyright 2003 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by KC 0329 Service AudioPrinted in The NetherlandsSubject to modification
Page
CLASS 1
LASER PRODUCT
GB
3139 785 30211
Version 1.1
LOCATION OF PC BOARDS
1-2
FRONT
STANDBY
PAR T
5DTC-DVD
LOADER
MECHANISM
+
CONTROL
BOARD
FRONT
DTC KEY
PAR T
MAINS & ECO
STBY BOARD
FRONT
DISPLAY
PAR T
ECO6 TUNER
BOARD
PCMCIA BOARD
(just in front of the
CD222 FE board)
CD222 FE
BOARD
CD222 BE
BOARD
SPK II BOARD
AV BOARD
FRONT
CONTROL
PAR T
SPK I BOARD
FRONT
HP & MIC
PAR T
AMPLIFER BOARD
100W = 2PCS
75W = 1PC
SUPPLY
BOARD
VERSION VARIATIONS:
Type /Versions:MX5500DMX5600DMX5700D
Features &
/21S /33S /35S/37/37/21R /21S /22S /25S
Board in used:
Karaoke-x--xx--
RDS + News------xx
Pro-Scanxxxxxx--
PCMCIA (Media Slot)xxxxxxxx
Standby - Clock Displayxxxxxxxx
ECO Standby - No Displayxxxxxxxx
Voltage Selectorx---xx--
Digital In / Outxxxxxxxx
Aux Inputxxxxxxxx
TV Inputxxxxxxxx
Line Outputxxxxxxxx
SCART output------xx
Pr, Pb & Y Outputsxxxxxx--
CVBS Outputxxxxxxxx
S-Video Outputxxxxxxxx
Headphone Socketxxxxxxxx
Mono BE board - CD222 P--------
Mono BE board - CD222 PM--xx--xx
Mono BE board - CD222 PMKxx--xx--
Tuner board - ECO6 System non-Cenelecxxxxxx--
Tuner board - ECO6 System Cenelec------xx
75W 6-Ch (Single SW) with 1x Amplifier pcbxx------
75W 7-Ch (Twin SW) with 1x Amplifier pcb---x----
100W 6-Ch (Single SW) with 2x Amplifier pcb--x-----
100W 7-Ch (Twin SW) with 2x Amplifier pcb---xxxxx
SPECIFICATIONS
1-3
GENERAL:
Mains voltage : 110-127V/220-240V Switchable for /21..
120V for /37
240V for /25S
220-230V for /22S/33S
Mains frequency: 50/60Hz
Power consumption : < 0,5W at ECO Standby
< 20W Standby (clock on, demo off)
Clock accuracy: < 4 seconds per day
Dimension centre unit : 435 x 100 x 360mm
TUNER:
FM
Tuning range: 87.5-108MHz
Grid: 50kHz for /21../22S/25S/33S
100kHz for /21../37
IF frequency: 10.7MHz ± 25kHz
Aerial input: 75Ω coaxial
Sensitivity at 26dB S/N: < 7µV
Selectivity at 600kHz bandwidth: > 25dB
Image rejection: > 25dB
Distortion at RF=1mV, dev. 75kHz: < 3%
-3dB Limiting point: < 8µV
Crosstalk at RF=1mV, dev. 40kHz: > 18dB
MW
Tuning range: 531-1602kHz for /21../22S/25S/33S
530-1700kHz for /21../37
Grid: 9kHz for /21../22S/25S/33S
10kHz for /21../37
IF frequency: 450kHz ± 1kHz
Aerial input: Frame aerial
Sensitivity at 26dB S/N: < 4.0mV/M
Selectivity at 18kHz bandwidth: > 18dB
IF rejection: > 45dB
Image rejection: > 28dB
Distortion at RF=50mV, m=80%: < 5%
AMPLIFIER:
Output power for 75W versions (MX5500D/21S/33S)
Stereo mode (DIN) : 2 x 75W RMS
3)
Surround mode 1): 75W RMS/channel
Output power for 100W versions (other versions)
Stereo mode (DIN) : 2 x 100W RMS 3) / 2 x 80W FTC
Surround mode 1): 100W RMS/channel
Frequency response ±3dB: 20Hz-20kHz
Hum (minimum volume): 200nW
Residue noise (min, volume): 40nW
Digital Sound Control: Stereo, 3D Sound, Multi modes
Bass & Treble: -3 to +3
4)
Input sensitivity
TV-in : 350mV ± 3dB
Aux-in : 880mV ± 2dB
Output sensitivity
Line out : 600mV ± 2dB at 47kΩ
Headphone (vol. max.) : 660mV ± 2dB at 32Ω
COMPACT DISC/VCD/DVD:
Video Decoding: MPEG-2 / MPEG-1
Video DAC: 10 Bits
Signal System: PAL / NTSC
Video Format: 4:3 / 16:9
MP3-CD bit rate
MP3-CD sampling frequencies
CBVS out
5)
6)
CVBS level : 1.0 ± 0.1V
: 32-256 kbs,variable bitrates
5)
: 32kHz, 44.1kHz, 48kHz
p-p
Luminance S/N ratio : > 45dB (unweighted)
YUV out
6)
Amplitude : 714mV ± 7mV
S/N ratio : > 50dB (unweighted)
S-Video out
6)
Y level : 1.0 ± 0.1V
p-p
Y S/N ratio : > 48dB (unweighted)
C level (burst) : 286mV
+1/-4 dB
p-p
Digital Out: Coaxial acc IEC61937 / IEC60958
Digital In: Coaxial acc IEC60958
2)
4)
1)
with only channel(s) under meausrement loaded, all other
channels are unloaded.
2)
with 8Ω, 120Hz - 12,5kHz & 10% THD for /37
3)
with 8Ω, 1kHz & 10% THD for version other than /37
4)
Frequency response in each setting is software controlled.
5)
Recording format: ISO9660, UDF format is not supported.
6)
Output terminals terminated with 75Ω
MEASUREMENT SETUP
Tuner FM
1-4
Bandpass
LF Voltmeter
e.g. PM2534
RF Generator
e.g. PM5326
DUT
250Hz-15kHz
e.g. 7122 707 48001
Ri=50Ω
S/N and distortion meter
e.g. Sound Technology ST1700B
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Tuner AM (MW,LW)
RF Generator
e.g. PM5326
Ri=50Ω
DUT
Frame aerial
e.g. 7122 707 89001
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
S/N and distortion meter
e.g. Sound Technology ST1700B
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
CD
Use Audio Signal Disc
(replaces test disc 3)
DUT
L
R
SBC429 4822 397 30184
S/N and distortion meter
e.g. Sound Technology ST1700B
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
Recorder
Use Universal Test Cassette CrO2 SBC419 4822 397 30069
or Universal Test Cassette FeSBC420 4822 397 30071
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
1-6
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
WAARSCHUWING
NL
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
“Pour votre sécurité, ces documents
doivent être utilisés par des spécialistes agréés, seuls habilités à réparer
votre appareil en panne”.
CLASS 1
LASER PRODUCT
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
3122 110 03420
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
"After servicing and before returning set to customer perform a
leakage current measurement test from all exposed metal parts to
earth ground to assure no shock hazard exist. The leakage current
must not exceed 0.5mA."
Varoitus !
SF
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
DISMANTLING INSTRUCTIONS
C4
1
2
Turn up the lever,
slide the bracket
as shown and lift
out of the bottom
chassis.
2-12-1
Dismantling of the Front Panel assembly
1) Loosen the 9 screws to dismantle the Top Cover (pos
252)
- 2 screws on each side
- 5 screws on the Rear Panel (pos 251).
C1
C1
A
C1
A
C1
2) Loosen 5 screws A and 8 catches C1 to slide the Front
Panel assembly (pos 101, 102, 103, etc) as per figure 1.
Note: To remove the Source / Volume control pc
board (pos 1105B) 2 nuts hidden below the
control knob assembly (pos 133, 134 and 135)
must first be removed.
C1
C1
A
A
C1
A
C1
Dismantling the Tuner, Mains and AV boards
1) Loosen 3 screws D and 2 catches C2 on the Rear panel
(pos 251) to remove the Tuner board assemby (pos 1101)
as pe figure 3.
2) Loosen 1 screws E and 2 catches C3 to unslot the Mains
board (pos 1102-A) out of the Rear panel as per figure 4.
3) Loosen bracket (pos 254) by turning a catch, sliding
towards the outside and lifting it upwards as per figure 5.
4) Loosen 7 screws F (8 screws for Scart version) and 2 C5
to separate Rear Plate assembly (pos 251 + 227) from
the Bottom plate as per figure 3.
5) Uncatch C4 to remove the AV board (pos 1104) from the
Bottom & Rear Plate assembly (pos 251 + 227) as per
figure 5.
Figure 3
Hints for re-assembly of Top Cover
Due to appearance design the Top cover (pos 252) is
sandwiched between the Front panel (pos 101) and the 2
side covers (pos 102 & 103), this make it necessary to
remove the 2 side covers before re-assembly of Top cover.
Figure 1
1) To remove the side cover use a small screw driver with
marking 16mm from the tip end.
2) Insert the screw driver into slot (as shown in figure 2) and
push the tip outwards to release the side cover catch.
The side cover can be pull outwards as soon as the top
catch is released.
Figure 4
Dismantling the 5DTC Module
1) Loosen 1 screws E and 2 catches C3 to remove the
Mains board as per figure 4.
2) Loosen bracket (pos 254) by turning a catch, sliding
towards the outside and lifting it upwards as per figure 5.
3) Loosen 3 screws G, lift up the 5DTC Module's (pos 1103-
A) rear and pull the module out towards the rear as per
figure 6.
Figure 5
G
G
Figure 2
Figure 6
2-2
2-2
Service positions
Dismantling the Mono FE and BE boards
1) Loosen 2 screws and 2 catches to remove the Mono BE
board (pos 1103-B).
2) Loosen 2 screws and 2 catches to remove the Mono FE
board (pos 1103-C).
3) Loosen 2 screws to remove the PCMCIA board (pos
1106).
Dismantling the Supply & Power Amplifier boards
1) Loosen 2 screws B mounting the Supply board's (pos
1102-B) heatsink to the Bottom Plate (pos 227) as per
figure 7.
Note: During re-assembly care must be taken to
ensure the Mains Transformer wires to the
Supply board is routed properly below the
board.
Service position A (Top cover removed)
2) Loosen 4 screws C (8 screws for 100W version with 2 pcs
of Amplifier boards) to dismantle the Power Amplifier
board (pos 1102-D) from the Bottom Plate as per figure
7.
Figure 7
Service position B (Front Panel loosen)
Service positions
2-32-3
Service position C (Supply and Amplifier boards loosen)
Amplifier Board
(Top piece)
Amplifier Board
(Bottom piece)
Service position D (Mains & AV boards loosen)
Mains Board
with non-
conductive
insulation
attached to the
copper pattern
Thick paper
Supply Board
Caution:
1) In some of the service positions the Mains supply is
exposed, therefore service technicians have to exercise
care to prevent electric shock.
2) The copper pattern on the Mains board should be cov-
ered with non-conductive insulation during fault-finding
on other parts of the set.
3) Insulation sheet (eg. thick paper or cardboard) should be
use during fault-finding to prevent short-circuiting of
copper patterns to metallic surroundings.
Thick paper
Note:
The ground connection between AV board stoko pin
1100 and Amplifier board stoko pin 1320 must be con-
nect ed during Service pos C and D in order to have
sound output at the Loudspeakers.
Service position E (5DTC Mechanism, Mono FE and Mono
BE boards loosen)
Thick paper
3-1
3-1
SERVICE TEST PROGRAM I
ADC
TEST
SEATING
Button pressed?
Y
9
Button pressed?
N
Display shows
"ADC Value"
(Ref Table 1)
To start service test program
hold DISC1 & STANDBY-ON
buttons depressed while
plugging in the mains cord*
Display shows the
ROM version
"S-Vyy"
* Hold till the Display is shown
S refers to Service Mode
V refers to Version
yy refers to Software version number of the uProcessor
(counting up from 01 to 99)
MAIN MENU
TUNER
TEST
N
Y
TUNING
Button pressed?
Y
Display Tuner Version
"ccc"
TUNING
Button pressed?
Y
N
N
QUARTZ
TEST
CLOCK-TIMER
Button pressed?
Y
Display shows
32K
Output at (Front Board)
pin 19 of uP = 2048Hz
CLOCK-TIMER
Button pressed?
N
N
DISPLAY
TEST
BII
Button pressed?
Y
Display shows Figure 1
and Standby LED is
Green
BII
Button pressed?
N
N
Figure 1
Y
N
Name
ADC1
ADC2
ADC3
ADC4
ADC5
Input line to
uProcessor IC
Key0
Key1
VU_IN
MUX_DET
Options
Has it reach
"ADC5 Value" ?
N
SEATING
Button pressed?
Y
Display shows next
"ADC Value"
(Refer Table 1)
Remarks
Return the value assign for each key button.
Return the value assign for each key button.
Varies according to the signal dc level
The set temperature is measured via this NTC
line, if lower than 69 the set goes into Standby.
Return the value assign for the different possible
options
Table 1
Note:
ADC Test is used for checking the ADC inputs to the microprocessor. The display
shows an ADC value between 0 and 255 for an input signal between 0 and 5V.
Service frequencies are
copied to the RAM (see Table 2)
Tuner works normally except:
PROGRAM button
Disconnect
Mains cord ?
Y
Service Mode left
PRESET
1
2
3
4
5
6
7
8
9
10
11
N
Europe
"EUR"
87.5MHz
108MHz
531kHz
1602kHz
558kHz
1494kHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
98MHz
USA
"USA"
87.5MHz
108MHz
530kHz
1700kHz
560kHz
1500kHz
98MHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
pin 19 of uP = 2,929.6875Hz
Y
Display shows
12M
Output at (Front Board)
9
Button pressed?
Y
Oversea
"OSE"
87.5MHz
108MHz
530/531kHz*
1700/1602kHz*
560/558kHz*
1500/1494kHz*
98/87.5MHz*
87.5MHz
87.5MHz
87.5MHz
87.5/98MHz*
N
East Europe
"EAS"
87.5MHz
108MHz
531kHz
1602kHz
558kHz
1494kHz
87.5MHz
87.5MHz
87.5MHz
87.5MHz
98MHz
Display shows Figure 2
and Standby LED is
Button pressed?
East Eur. Extended-band
Table 2
Note: * Depending on the selected grid frequency (9 or 10kHz).
By holding the "DISC5" and "STANDBY-ON" buttons depressed while switching on the Mains supply, one of the
undermentioned features will be activated:
- the tuning grid frequency is toggled between 9kHz and 10kHz for the Oversea (/21) version.
Y
RED
9
Y
"EAS"
65.81MHz
108MHz
74MHz
87.5MHz
531kHz
1602kHz
558kHz
1494kHz
98MHz
70.01MHz
65.81MHz
N
TEST
Figure 2
Activated with
ACTION
Various
other Tests
EEPROM TESTSome test patterns will be sent to the EEPROM.
TEST
AUTO STANDBY
TOGGLE
ROTARY
ENCODER TEST
LEAVE SERVICE
TEST PROGRAM
T
9 to Exit
SEEPROM FORMAT
SUBW +
(Remote Control)
SOURCE / VOLUME
Knob
Disconnect
mains cord
"PASS" is displayed if the uProcessor read back
the test patterns correctly, otherwise "FAIL" will be
displayed.
Load default data. Display shows "NEW" for 1 second.
Caution!
All presets from the customer will be lost!!
Pressing this button will toggle between the status
"AUTO STANDBY ON" and "AUTO STANDBY OFF".
The status will scroll once across the Display.
Display shows value for 2 seconds.
Values increases or decreases in steps of 1 until
0 (Min.) or 40 (Max.) is reached.
5DTC MX.. Range Service Test Program dd wk0302
3-23-2
SERVICE TEST PROGRAM II
DVD SVC MENU
DVD I
2C
COMMUNICATION
TEST
MUTE
Button pressed?
Y
N
DVD VERSION
MATRIX INFO
Button pressed?
DIM
To start service test program
hold DISC1 & STANDBY-ON
buttons depressed while
MAIN MENU
plugging in the mains cord*
Display shows the
ROM version
"S-Vyy"
(Main menu)
* Hold till the Display is shown
S refers to Service Mode
V refers to Version
yy refers to Software version number of the uProcessor
(counting up from 01 to 99)
DVD SERVICE
TEST
DISC
Button pressed?
Y
Display shows
"DVD SERVICE"
N
Note:
1. Remote Control must be in DVD source before start of any DVD Service Test.
2. All buttons on this "DVD SERVICE" test refers to the buttons on the Remote control.
3. Awaits for the mechanism to initialized before performing DVD test.
DVD PLAYER TEST
(with User interaction)
N
Y
N
9
Button pressed?
Y
N
VOL +
Button pressed?
Y
N
Button pressed?
DVD DEALER TEST
(without User interaction)
VOL -
Y
Send request for
DVD Software Version
2
C ports
via I
Are Software
Versions Received?
Y
Display shows
"BEA-xxVxx"
5DTCx.x
9
Button pressed?
Y
STEP
Choose step
by pressing
N
S
1
2
3
4
T
Display shows
"FAIL"
5
DISPLAY
SLASH '###'
REGION '#'
KARAOKE
or
NON KARA
V/O SCART
or
V/O PrPbY
TV - NTSC
or
TV - PAL
or
TV - AUTO
REMARKS
Slash version number
Region code setting (Number 1 - 6)
Karaoke feature
Video Output setting
TV system setting
Press
9
to exit
Choose step
by pressing
S
T
DVD Version Matrix Info is used to read the version matrix information
that are stored/defined in the DVD module software.
N
9
Button pressed?
Y
N
STEP
DISPLAY
1
FEA-zzzz
2
TRAY
3
SLEDGE
4
MOTOR
5
FOC-RDL
FOC FAIL
RDL FAIL
GROOVES
6
ACTION
Returns the Front End Ali Servo Processor
software version.
Tray 1 can be open or close with the
PROGRAM buttons repectively.
Insert a CD onto Tray 1 and close before
proceding to next test.
Sledge can be move in and out with the
and PROGRAM buttons respectively.
Dismotor is turn on and off by pressing
PROGRAM buttons repectively.
DVD Module does a Focus test follow by Radial
test if focus is successful.
BII
BII
BII
and
and
Is displayed when the focus test fail.
Is displayed when the radial test fail.
In this test the laser spot can jumps to another
position.
Press
BII
to jump to the next postion &
PROGRAM to jump to the previous postion.
Disconnect mains cord to exit the Service Test
Program.
DVD Dealer Test is used to check the flash RAM,
the SDRAM CLOCK, the NVRAM and the I
communication (I
2
and I
C SDPIF IC)
STEP
DISPLAY
1
CHECKSUM
2
SDRAM CLK
3
NVRAM
2
4
I
C COMM
2
C NVRAM I2C DAC, I2C 5DTC
ACTION
Check the correctness of the
checksum in the flash. Display will
show "PASS" or "FAIL" accordingly.
Test the SDRAM clock output.
Display "PASS" or "FAIL"
accordingly.
Pro-Scan: 114MHz +/- 25ppm
Non Pro-Scan: 108MHz +/- 25ppm
Makes a write followed by a read
test to the NVRAM. Display will
show "PASS" or "FAIL" accordingly.
2
Checks I
C bus to NVRAM, DAC,
5DTC and SDPIF IC. Display will
show "PASS" or "FAIL" accordingly.
Disconnect mains cord to exit
the Service Test Program.
2
C
DVD I2C Communication Test is used to test the I2C communication
port between the DVD module and the microprocessor of the set.
where: BEA-xxVxx is the Back End Application software version
5DTCx.x is the 5DTC software version
5DTC MX.. Range Service Test Program dd wk0302
3-3
Reprogramming of DVD version matrix
Caution:
This information is confidential and may not be distributed. Only a qualified service person
should reprogram the mono BE board.
After replacement/repair of the Mono BE board, the customer settings and also the region code may be lost.
Reprogramming will put the set back in the state in which it has left the factory, i.e. with the default settings
and the allowed region code.
Reprogramming will be done by way of the Remote Control.
Put the player in stop mode, Disc 1 with no disc loaded.
Do the following steps with the Remote Control:
1) Press <DISC MENU> followed by numerical keys <1> <5> <9>The set display shows: “- 0 - 0 - 0 - 0 - ”
2) Press now successively the following numerical keys :
for MX5500D/21S : <3><2><4> <0><1><1> <0><0> AP
for MX5500D/33S : <3><5><4> <0><1><2> <0><0> AP - Korea
for MX5500D/35S : <6><5><4> <0><1><1> <0><0 AP - China
for MX5500D/37 : <1><1><4> <0><1><3> <0><0> US
for MX5600D/37 : <1><1><4> <0><1><3> <0><0> US
for MX5700D/21R : <3><2><4> <0><1><1> <0><0> AP
for MX5700D/21S : <3><2><4> <0><1><1> <0><0> AP
for MX5700D/22S : <2><2><4> <0><1><4> <0><0> Europe
for MX5700D/25S : <2><2><4> <0><1><4> <0><0> UK
3) Press <DISC MENU> again. The set display will show: “DONE”.Caution: The set needs about 3 seconds to reset to required setting.
4) Disconnect mains to ensure proper reset.
Procedure for check Software version
1) Select Disc with the Remote Control
2) Press <SYSTEM MENU>
3) Use the down key move all the way down (4x) to
bottom of "Setup Menu".
4) Use the right key move to the sub-menu.
5) Use the down key move down (3x) to "Default" and
down one more time to see the software version.
6) The TV screen will shows:
R
1000 BEA3131PV08 R2812 V72
where 1000 = DVD version matrix
Yes/No, Default Video O/P, Default TV system)
31V08 = BE software version
2812 = FE software version
72 = 5DTC servo version
(Region, Karaoke
7) Press <OK> three times to exit.
Procedure to upgrade software
1) Power up the set and open tray Disc 1.
2) Place upgrade CD-ROM onto tray and close.
3) The set will display "DOWNLOAD" while the TV screen
will shows:
Reading --> Update BEA --> Writing --> Done -->
Update FEA --> FEA Finish --> Unload Disc 1
4) Tray Disc 1 should then open.
5) The whole process should last for less than 2 minutes.
Remove the upgrade CD-ROM and unplug the Mains
supply.
SET BLOCK DIAGRAM
4-14-1
ECO 6
DVD Module
Power Amplifier
TDA8920
L/R
POWER AMP
TDA8920
SURROUND
POWER AMP
1/2XTDA8920
1/2XTDA8920
Front Display
Mains and Regulator
MAINS TRAFO
LPS COIL
ECO Standby
TMP88CU74F
Note: All others are in the AV board.
MX3900D_130_wk302-2
MAIN WIRING DIAGRAM
4-2
4-2
TUNER
AD
140mm
EH
240mm
1
8P
for ECO SET ONLY
1
AD
180mm
4P
EH
10P
180mm
1
1
AV
1
1
BD
400mm
Prefold
13P
for MX39/55/56/58/59
for i6000
FE
BD
180mm
10P
Prefold
1
FE
5PAD120mm
1
for ECO SET ONLY
POWER MODULE
Refer to page 4-3 for details
FRONT DISPLAY
MX55/56/58/59
MX3900D
MX39/55/56
MX58/59
AD
13P
100mm
AD
400mm
Prefold
17P
for MX55/56/58/59
for MX3900D
1
AD Prefold
1
1
1
1
4P 340mm (non K’ok)
8P 340mm (K’ok)
1
1
for MX39/55/56/58/59
for i6000
PCMCIA
BD
180mm
10P
Prefold
13P 180mm (MX39/55/56)
13P 220mm (MX58)
Prefold AD
10P 280mm (MX39/55/56)
14P 220mm (MX58)
Prefold AD
Prefold AD
16P/18P(K’ok) 180mm (MX39/55/56)
22P 220mm (MX58)
16P 220mm (MX59)
FFC
FLT
40P
40P
AD
280mm
1
FMN
1
SCART 0
Mute_AV
GND_V
R_Pr
GND_V
C_B_Pb
GND_V
Y_G_Y
GND_V
CVBS
10
GND_V
Y
14
MX39/55/56
MX58/59
GND_V
C
13
40P
FLT
for MX3900D
1
for MX5800SA
22
DVD_SC
1
1
GND_Sc
DVD_L
GND_L
DVD_R
GND_R
DVD_SUB
GND_SUB
DVD_Ls
GND_S
DVD_C
GND_C
DVD_Rs
GND_S
GND_d
DIG_OUT
DIG_IN_1
DIG_IN_2
GND_MIC
16
18
MIC_IN
GND_a
DPL2_R
GND_a
DPL2_L
MX39/55/56/59
MX5800SA
K’ok
DVD Module
Refer to page 4-4
for details
HDPH & MIC
1
2P
220mm
FRONT CONTROL
DTC
KEY
POWER SWITCH
Prefold
AD
7P
340mm
AD
4P 220mm (MX39/55/56)
8P 220mm (MX58/59)
for MX5500/5600
4-34-3
WIRING DIAGRAM - POWER MODULE DETAILS
4P
10PEH220mm
180mm
10P
Prefold
180mm
10P
Prefold
180mm
BD
BD
AD
5PAD120mm
1
1
1
1
240mm
EH
SUPPLY
Amplifier
3104 213 3525
1
EH 10P 280mm
1
1
TRAFO
1
NOTE :
1
VH 3X
150mm
Blue/Yellow
Red/Black
VH 3X
150mm
FAN
1
1
EH 9P
1
1
1
1
1
120mm
EH 8P
120mm
EH 8P
120mm
1
MAINS
and
ECO STBY
1
1
1
10
1
2
3
4
5
6
7
8
9
SPK I
1
1
2
3
4
5
6
7
8
9
10
11
12
75W
1
SUR L
SUB-WOOFER
1
6-CHANNEL
CENTER
75W 6-CHANNEL : 1 X CLASS-D AMPLIFIER + SPK I
75W 7-CHANNEL : 1 X CLASS-D AMPLIFIER + SPK I + SPK II
100W : 2 X CLASS-D AMPLIFIER + SPK I + SPK II
Front Display part - Circuit diagram ............................................................. 6-2
Front Display part - Component & Chip layouts .......................................... 6-3
Front Display part - Chip layout Part A......................................................... 6-4
Front Display part - Chip layout Part B ........................................................ 6-5
Front Control part - Chip layout .................................................................... 6-6
Front Control part - Component layout ........................................................ 6-7
Front Control part - Circuit diagram ............................................................. 6-8
DTC Key part - Component & Chip layouts ................................................. 6-9
DTC Key part - Circuit diagram .................................................................. 6-10
Power Switch part - Circuit diagram ........................................................... 6-10
Power Switch part - Component & Chip layouts ........................................ 6-11
HDPH & Mic part - Circuit diagram (Non-Karaoke version)....................... 6-12
HDPH & Mic part - Comp. & Chip layouts (Non-Karaoke version) ............ 6-13
HDPH & Mic part - Circuit diagram (Karaoke version) .............................. 6-14
HDPH & Mic part - Comp. & Chip layouts (Karaoke version) .................... 6-15
Electrical parts list....................................................................................... 6-16
PIN CONFIGURATION
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Symbol.
VDD
VSS
/CS1
/RES
A0
/RD
/WR
D0
D1
D2
D3
D4
D5
D6
D7
LED+
LED-
BZ1
BZ2
Description
Power supply for logic circuit (+5V)
Ground (0V)
Input, when /CS1 = 0, the chip select become active
Input low active, System reset
Usually connected to the low-order bit of the MPU address bus and used
to identify the data or a command.
A0=1: D0 - D7 are display data
A0=0: D0 - D7 are display control data
For the connection of 80-series MPU:
Input, Active low
The /RD signal of the 80-series MPU is entered in this pin. When this
signal is kept low, the ST7522 data bus is in the output status.
For the connection of 80-series MPU:
Input, Active low
The /WR signal of the 80-series MPU is entered in this pin. A signal on
the data bus is fetched at the rising edge of /WR signal.
Data input/output (LSB)
Data input/output
Data input/output
Data input/output
Data input/output
Data input/output
Data input/output
Data input/output (MSB)
Anode of backlight
Cathode of backlight
Bezel ground (connected together)
Bezel ground (connected together)
6-2
FRONT DISPLAY PART - CIRCUIT DIAGRAM
A
B
C
D
E
G
H
F
1101 C2
1104 A13
1105 B13
1106 E13
1107 A7
2101 F4
2102 F2
2103 G3
2104 G1
2105 G3
For RDS version only
3108
2104
2128
560p
2106 H1
2107 H2
2108 F6
2109 F6
2110 F5
2111 F 8
2112 F6
2113 G5
2114 H4
2115 H7
2116 H7
2117 H5
2118 H5
2119 H7
2120 H7
2121 G12
2122 G10
2123 G10
2124 G11
2125 G11
2128 G1
2130 B8
2131 B8
2132 B9
2141 F5
3100 B2
3101 B2
3102 B3
3103 B3
3105 F4
12345678910111213
3134
100R
6104
1K5
7102
SAA6581T
560p
4
8
7
15
9
MPX
SCOUT
CIN
TCON
MODE
57 Khz
BANDPASS
(8th ORDER)
CLOCKED
COMP
TEST
CTRL
2106
82p
3107
10K
OSC
CLK
OSCI
13
3113
220K
5105
AT-51
VSSA
&
3100
FE-ST-VK-N
2102
1n0
512
VDDA
POW SUPPL
&
RESET
RDS/RBDS
DEM
SIGNAL
QUALITY
DET
VSSA
OSCO
14
611
3114
2K2
1K
1101
+D
VSSD
7106
BC847B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VDDD
VREF
SYNC
RDCL
RDDA
QUAL
2107
47p
3101
+E
3
10
16
2
1
68R
+E
2103
3102
BC847B
GND_B
1N4003
100n
1K0
3111
1K0
3136
68R
68R
7107
6119
2u2
2105
3109
+C
3110
3112
BC847B
3103
1K
RotaryVolB
RotaryVolA
Rot_Jog_B
Rot_Jog_A
LPS_LED
Stdby_LED
LedShStr
LedShClk
LedShData
TuRDS
TuRdsClk
10K
TuRdsData
10K
LTL-816TDK3
3135
7101
LED-
LCM_Dim
LCM_BackLit
Key1
LPS_LED
Key0
Stdby_LED
LedShClk
RC6
+5V6
1K
TMP88CU74F
D0
D1
D2
D3
D4
D5
D6
D7
10K
3175
LedShData
LedShStr
DVD_5V
Rot_Jog_A
VU_IN
2101
220n
3106 F5
3107 F2
3108 F1
3109 G3
3110 G3
+D
3105
3177
6105
BAT54
470K
VU_LED
7100
3176
10K
10K
2114
3111 H 3
3112 H3
3113 H2
3114 H2
3115 F8
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
BAT54 COL
10n
7105
BC847B
+D
V24
V25
V26
V27
V28
V29
V30
V31
V32
V33
V34
V35
V36
VKK
-SCK1
SI1
1
3106
6118
3125
LCM_BackLit
V23
SO1
Rot_Jog_B
Reset
3116 F8
3117 F8
3118 F5
3119 G8
3122 H6
17
18
19
3142
1K0
3141
LCM_CS1
RD
WR
LCM_Dim
V21
V20
V22
8-Bit h. break. v.
80k pull
down
8-Bit h. breakdown v.
out. port w. latchP9
PD
source open
drain 80k p.d.
5-Bit h. breakd. v.
out w. latch
8-Bit Input/Output
(tri-state)
P03
P04
P05
3
4
RotaryVolB
RotaryVolA
I2C_Clk2
MUX_VU
1u0
2141
10K
1K0
3130
680K
10n
2118
3125 H5
3130 H5
3131 H6
3132 H5
3134 A3
14
15
16
1K0
1K0
3144
1K0
3143
3145
LCM_RESRDWR
LCM_A0
LCM_A0
LCM_CS1
LCM_RES
V17
V18
V19
P0
VSS
P06
P07
7
LPC
I2C_Clk1
MpOscShift
2110
3118
4K7
2113
+C
2117
470n
3132
3135 A4
3136 A3
3137 D9
3141 B5
3142 A5
3143 B5
3144 A5
3145 B5
3158 F10
3159 F10
3160 F10
3161 F12
3162 F12
3163 G12
3164 G11
3165 G11
3170 A12
3171 A12
3172 A12
3173 B12
FE-ST-VK-N
8
7
9
10
11
12
13
1K0
D0D1D2
V16
VFT driver circuit (automatic display)
D3D4D5
V12
V13
V14
V15
8-Bit high breakdown voltage8-Bit high breakdown v.
output port with latchoutput port with latchout w. latch P8
These assembly drawings show a summary of all possible versions.
For components used in a specific version see schematic diagram respectively partslist.
If sensitivity of frequency counter is too low adjust to max. channel separation
(input signal: stereo left 90% + 9%, adjust output on right channel to minimum)
2)
RC network serves for damping the IF-filter while adjusting the other one.
3)
For AM RF adjustments the original frame antenna has to be used!
TUNER ADJUSTMENT TABLE
( ECO6 Cenelec FM/MW - and FM/MW/LW - versions with AM-frame aerial )
max.
symmetric
f
o
max.
symmetric
f
o
ECO6 Sys Cenelec, 190599
B
∆f = ±30kHz
V
RF
as low as
possible
MW has to be aligned before LW.
3-band
2-band
Note: The FM-frontend unit has already been adjusted by the factory
and needs therefore no further adjustments for service purposes.
2141
shortcircuit
to block AFC
21
IC 7101
see
remark
2)
220R
100nF
36
IC 7101
220R
100nF
40
IC 7101
450kHz
connect pin 6 of
IC 7101 (AM Osc.)
with 3.3kΩ to Vcc
AM AFC
MW
continuous wave
VRF = 2mV
∆f = ±10kHz
V
RF
= 0.5mV
(as low as
possible)
Use Service Testprogram. By selecting the TUNER TEST test frequencies will be stored as preset frequencies automatically.
AM FRAME AERIAL
FM 75Ω
FM FRONTEND
Birdy Filter
ECO6 Sys-Cenelec, layout stage .6, 160501
1101 B5
1102 B5
1103 C5
1110 B4
1120 A4
1130 A5
1131 C5
1132 A4
2106 B4
2107 B3
2128 A3
2129 B3
2133 C1
2138 B1
2144 B1
2162 A4
2191 B4
3142 C2
5102 C4
5103 C4
5109 B3
5110 A2
5111 A3
5112 A2
5114 A2
5115 C2
5119 B2
5121 B2
5122 C3
5123 C3
7104 C4
7105 C5
7112 B1
9101 A2
9102 B2
9103 A1
9104 B1
9105 B1
9106 B1
9107 B4
9108 B3
9109 C2
9110 A4
9111 A3
TUNER BOARD ECO6
Systems - Cenelec
/ componentside view
B
A
These assembly drawings show a summary of all possible versions.
For components used in a specific version see schematic diagram respectively partslist.
Scart Non-Scart
3424 use use 3425 use use -
3426 - use -
3427 - use 3428 - - -
4424 - - use
4425 - - use
4426 use - use
4427 use - use
4428 use use use
This assembly drawing shows a summary of all possible versions. For components used in a specific version see schematic diagram and respective parts list
PART A
The following reworks are make at prod. start-up on the SMD side:
1. 2 chip cap 4,7nF (4822 126 13193) added across Scart connector pins
2/4 and 4/6.
2. Wire added between Scart pin 5 to ground pin 1100.
3. Wire added between Elco 2126 -ve pin and 2123 -ve pin.
4. Zener diode BZX79-C12 (4822 130 34197) is added across Elco 2123
with the cathode to the +ve pin.
5. Wire added between EMC ground to Dig ground below the Digital In/Out
socket 1181
PART B
2 chip cap 4,7nF
PART C
PART D
3139 113 3500 pt5 dd wk318
TOP VIEW - CHIP & COMPONENT
9-79-7
This assembly drawing shows a summary of all possible versions. For components used in a specific version see schematic diagram and respective parts list
PART E
PART F
PART G
PART H
3139 113 3500 pt5 dd wk318
BOTTOM VIEW - PART A
9-89-8
PART A
BOTTOM VIEW - PART B
9-9
9-9
PART B
BOTTOM VIEW - PART C
9-10
9-10
2 chip cap 4,7nF
PART C
BOTTOM VIEW - PART D
9-11
9-11
PART D
BOTTOM VIEW - PART E
9-12
9-12
PART E
BOTTOM VIEW - PART F
9-13
9-13
PART F
BOTTOM VIEW - PART G
9-14
9-14
PART G
BOTTOM VIEW - PART H
9-15
9-15
PART H
MISCELLANEOUS
11812422 026 05399Socket Aux-in/Digital-In/Out
11824822 265 11151Socket TV-in/Line-out
11832422 033 00468Socket CVBS/S-Video
11842422 026 05342Socket Pr/Pb/Ynon-Scart
11862422 025 12352Scart ConnectorScart
11872422 127 00476P-Scan SwitchP-scan
12304822 267 10733Flex Socket 4Pnon-Kara
12314822 267 10729Flex Socket 10P
12324822 267 10733Flex Socket 4P
12344822 267 10729Flex Socket 10P
12364822 267 10954Flex Socket 5P
12374822 265 11515Flex Socket 8P
12384822 267 10738Flex Socket 13P
12404822 267 51255Flex Socket 14P
12422422 025 16591Flex Socket 13P
12434822 265 11515Flex Socket 8PKara
14012422 025 16525Flex Socket 16Pnon-Kara
14012422 025 18239Flex Socket 18PKara
14052422 025 16587Flex Socket 10P
CAPACITORS
21003198 016 310201nF 25V
21013198 016 310201nF 25V
21022238 586 59812100nF +80/-20% 50V
21032020 552 94427100pF 5% 50V
21042020 552 94427100pF 5% 50V
21053198 017 44740470nF 10V
21063198 017 44740470nF 10V
21072020 552 96327330nF 10% 16V
21084822 126 13879220nF +80/-20% 16V
21092020 552 94427100pF 5% 50V
21105322 126 115793,3nF 10% 63V
21113198 016 310201nF 25V
21125322 126 1158310nF 10% 50V
21133198 017 44740470nF 10V
21143198 017 44740470nF 10V
21152020 552 96327330nF 10% 16V
21164822 126 13879220nF +80/-20% 16V
21174822 126 142382,2nF 50V
21185322 126 115793,3nF 10% 63V
21193198 016 310201nF 25V
21205322 126 1158310nF 10% 50V
21213198 017 44740470nF 10V
21222238 916 1564122nF 10% 25V
21234822 124 8115122uF 50V
21244822 124 40196220uF 20% 16V
21254822 126 142382,2nF 50V
21264822 124 4043347uF 20% 25V
21272020 552 94427100pF 5% 50V
21282020 552 94427100pF 5% 50V
21292238 586 59812100nF +80/-20% 50V
21302238 586 59812100nF +80/-20% 50V
9-169-16
ELECTRICAL PARTS LIST - AV BOARDELECTRICAL PARTS LIST - AV BOARD
21392238 586 59812100nF +80/-20% 50V
21432238 586 59812100nF +80/-20% 50V
21444822 126 1395668pF 5% 63V
21454822 126 1395668pF 5% 63V
21504822 126 140431uF +80/-20% 16V
21514822 126 140431uF +80/-20% 16V
21523198 016 310201nF 25V
21533198 016 310201nF 25V
21544822 126 140431uF +80/-20% 16V
21554822 126 140431uF +80/-20% 16V
21562020 552 94427100pF 5% 50V
21572020 552 94427100pF 5% 50V
21604822 126 1395668pF 5% 63V
21614822 126 1395668pF 5% 63V
21624822 126 140431uF +80/-20% 16V
21633198 016 310201nF 25V
21643198 016 310201nF 25V
21653198 016 310201nF 25V
21664822 124 407694,7uF 20% 100V
21674822 126 140431uF +80/-20% 16V
21683198 016 310201nF 25V
21704822 126 142382,2nF 50V
21723198 017 3473047nF 16V
21733198 017 3473047nF 16V
21743198 017 3473047nF 16V
21993198 017 410501uF 10V
22014822 124 401841000uF 20% 10V
22024822 124 4024810uF 20% 63V
22074822 124 4175147uF 20% 50V
22084822 124 4175147uF 20% 50V
22094822 126 14508180pF 5% 50V
22104822 126 14508180pF 5% 50V
22114822 126 13881470pF 5% 50V
22124822 126 13881470pF 5% 50V
22132020 552 94427100pF 5% 50V
22143198 016 310201nF 25V
22154822 124 8115122uF 50V
22163198 016 310201nF 25V
22174822 124 8115122uF 50V
22182020 552 94427100pF 5% 50V
22194822 124 4043347uF 20% 25V
22202238 916 1564122nF 10% 25V
22244822 124 8115122uF 50V
22254822 124 8115122uF 50V
22264822 124 40255100uF 20% 63V
22274822 124 8115122uF 50V
22314822 124 80791470uF 20% 16V
22324822 124 40196220uF 20% 16V
22334822 124 41584100uF 20% 10V
22402020 012 93583100uF 20% 25V
22413198 026 510201000uF 20% 50V
22424822 124 4043347uF 20% 25V
Kara
22543198 017 44740470nF 10V
22803198 017 44740470nF 10V
22813198 017 44740470nF 10V
22823198 017 44740470nF 10V
22833198 017 44740470nF 10V
23023198 017 44740470nF 10V
23032238 586 59812100nF +80/-20% 50V
23043198 017 44740470nF 10V
23052020 552 94427100pF 5% 50V
23082020 552 94427100pF 5% 50V
23094822 126 131934,7nF 10% 63V
23104822 126 131934,7nF 10% 63V
23114822 124 4043347uF 20% 25V
23122238 916 1564122nF 10% 25V
23134822 124 4043347uF 20% 25V
23143198 016 310201nF 25V
23183198 017 44740470nF 10V
23193198 017 44740470nF 10V
23203198 017 44740470nF 10V
23213198 017 44740470nF 10V
23223198 017 44740470nF 10V
23244822 124 120324,7uF 20% 50V
23252020 552 94427100pF 5% 50V
23263198 017 44740470nF 10V
23272020 552 94427100pF 5% 50V
23282020 552 94427100pF 5% 50V
23292020 552 96684470nF 10% 25V
23303198 017 44740470nF 10V
23314822 126 131934,7nF 10% 63V
23322020 552 96684470nF 10% 25V
23332020 552 96326220nF 10% 16V
23342222 780 15656330nF 10% 16V
23352020 552 94427100pF 5% 50V
23364822 124 4043347uF 20% 25V
23372238 916 1564122nF 10% 25V
23384822 124 4043347uF 20% 25V
23393198 016 310201nF 25V
23402020 552 94427100pF 5% 50V
23414822 126 140431uF +80/-20% 16V
23424822 126 140431uF +80/-20% 16V
Single-SW
23424822 126 13879220nF +80/-20% 16VTwin-SW
23434822 126 140431uF +80/-20% 16VSingle-SW
23432020 552 96684470nF 10% 25VTwin-SW
23444822 126 140431uF +80/-20% 16VSingle-SW
23442020 552 96684470nF 10% 25VTwin-SW
23492238 586 59812100nF +80/-20% 50V
23523198 017 44740470nF 10V
23532238 586 59812100nF +80/-20% 50V
23804822 126 144721uF 10% X7R 0805 10V
24004822 126 13883220pF 5% 50VScart
24014822 126 13883220pF 5% 50VScart
24022238 586 59812100nF +80/-20% 50V
24033198 017 4223022nF 50V
Scart
24044822 126 13883220pF 5% 50VScart
24074822 126 13883220pF 5% 50V
24094822 126 13883220pF 5% 50V
24104822 126 13883220pF 5% 50V
24112020 552 94427100pF 5% 50V
24122020 552 94427100pF 5% 50V
24132020 552 94427100pF 5% 50V
24143198 017 410501uF 10V
Scart
24153198 017 410501uF 10VScart
24172020 552 94427100pF 5% 50V
24182020 552 94427100pF 5% 50V
24204822 124 40196220uF 20% 16V
24214822 124 40196220uF 20% 16V
24222238 586 59812100nF +80/-20% 50V
24234822 126 14249560pF 10% 50V
24242238 586 59812100nF +80/-20% 50V
24252238 586 59812100nF +80/-20% 50V
24265322 126 1158310nF 10% 50V
24274822 126 14508180pF 5% 50V
24284822 126 1178547pF 5% 50V
24294822 126 14241330pF 50V
24304822 124 407694,7uF 20% 100VScart
24314822 126 140431uF +80/-20% 16VScart
24324822 126 140431uF +80/-20% 16VScart
24333198 016 310201nF 25VScart
24343198 016 310201nF 25VScart
24353198 016 310201nF 25VScart
24363198 016 310201nF 25VScart
RESISTORS
31004822 051 30221220R 5% 0,062W
31014822 051 30221220R 5% 0,062W
31024822 051 301021k 5% 0,062W
31034822 051 301021k 5% 0,062W
31044822 051 305625k6 5% 0,063W
31054822 117 129028k2 1% 0,063W
31064822 051 305625k6 5% 0,063W
31074822 051 3018318k 5% 0,062W
31084822 051 3010310k 5% 0,062W
31094822 117 1292547k 1% 0,063W
31104822 051 306826k8 5% 0,062W
31114822 051 305625k6 5% 0,063W
31124822 117 129028k2 1% 0,063W
31134822 051 3018318k 5% 0,062W
31144822 051 3010310k 5% 0,062W
31154822 051 305625k6 5% 0,063W
31164822 117 1292547k 1% 0,063W
31174822 051 3010310k 5% 0,062W
31224822 051 306826k8 5% 0,062W
31234822 051 30271270R 5% 0,062W
31244822 051 30271270R 5% 0,062W
9-179-17
ELECTRICAL PARTS LIST - AV BOARDELECTRICAL PARTS LIST - AV BOARD
RESISTORS
31254822 051 30271270R 5% 0,062W
31264822 051 30271270R 5% 0,062W
31274822 051 301021k 5% 0,062W
31284822 117 12891220k 1% ERJ3E
31294822 117 12891220k 1% ERJ3E
31304822 051 30101100R 5% 0,062W
31314822 051 30101100R 5% 0,062W
31324822 051 30101100R 5% 0,062W
31334822 051 30101100R 5% 0,062W
31354822 051 305625k6 5% 0,063W
31374822 051 3010310k 5% 0,062W
31404822 117 1292547k 1% 0,063W
31424822 051 303323k3 5% 0,062W
31434822 117 1292547k 1% 0,063W
31454822 051 303323k3 5% 0,062W
31464822 117 1292547k 1% 0,063W
31474822 117 1292547k 1% 0,063W
31484822 051 303323k3 5% 0,062W
31494822 051 303323k3 5% 0,062W
31504822 051 301021k 5% 0,062W
31514822 051 30471470R 5% 0,062W
31524822 117 1292547k 1% 0,063W
31534822 051 302222k2 5% 0,062W
31544822 117 1292547k 1% 0,063W
31554822 051 3010310k 5% 0,062W
31564822 051 302222k2 5% 0,062W
31574822 051 301021k 5% 0,062W
31584822 051 30471470R 5% 0,062W
31594822 117 1292547k 1% 0,063W
31604822 051 302222k2 5% 0,062Wnon-Kara
31604822 051 303323k3 5% 0,062Wnon-Kara/Scart
31604822 051 304724k7 5% 0,062WKara
31614822 051 30151150R 5% 0,062W
31624822 051 301021k 5% 0,062W
31634822 051 303323k3 5% 0,062W
31644822 051 303323k3 5% 0,062W
31654822 051 303323k3 5% 0,062W
31664822 051 303323k3 5% 0,062W
31704822 117 1292547k 1% 0,063W
31804822 051 3010310k 5% 0,062W
31824822 051 3010310k 5% 0,062W
31834822 051 3010310k 5% 0,062W
32004822 117 13632100k 1% 0,62W
32014822 117 13632100k 1% 0,62W
32024822 051 3010310k 5% 0,062W
32034822 051 3010310k 5% 0,062W
32044822 051 3010310k 5% 0,062W
32054822 051 301021k 5% 0,062W
32064822 051 305625k6 5% 0,063W
32074822 051 304724k7 5% 0,062W
32084822 051 304724k7 5% 0,062W
32094822 051 301021k 5% 0,062W
32104822 051 301021k 5% 0,062W
32114822 051 3033933R 5% 0,062W
32124822 051 3033933R 5% 0,062W
32134822 051 3047947R 5% 0,062W
32144822 051 3047947R 5% 0,062W
32154822 051 301021k 5% 0,062W
32244822 051 301021k 5% 0,062W
32254822 051 301021k 5% 0,062W
32304822 051 3027327k 5% 0,062W
32314822 051 3027327k 5% 0,062W
32324822 051 3012312k 5% 0,062W
32334822 051 306826k8 5% 0,062W
32344822 051 30221220R 5% 0,062W
32354822 051 30221220R 5% 0,062W
32364822 051 306826k8 5% 0,062W
32374822 051 3012312k 5% 0,062W
32384822 052 1010910R 5% 0,33W
32394822 051 3010310k 5% 0,062W
32404822 117 1292547k 1% 0,063W
32454822 051 305625k6 5% 0,063W
32504822 117 1292547k 1% 0,063W
32524822 051 305625k6 5% 0,063W
32544822 117 1292547k 1% 0,063W
32564822 051 304724k7 5% 0,062W
32574822 051 304724k7 5% 0,062W
32594822 117 129028k2 1% 0,063W
32604822 051 3010310k 5% 0,062W
32614822 051 3010310k 5% 0,062W
32624822 051 301021k 5% 0,062W
32634822 051 301021k 5% 0,062W
32654822 051 30471470R 5% 0,062W
32684822 051 301021k 5% 0,062W
32694822 051 30221220R 5% 0,062W
32704822 051 30471470R 5% 0,062W
32714822 051 30471470R 5% 0,062W
32724822 051 306826k8 5% 0,062W
32734822 051 3010310k 5% 0,062W
32744822 051 306826k8 5% 0,062W
32754822 051 3068968R 5% 0,063W
32764822 051 301021k 5% 0,062W
32774822 117 1292547k 1% 0,063W
32904822 052 102282R2 5% 0,33W
33024822 051 3022322k 5% 0,062W
33034822 117 118171k2 1% 1/16W
33044822 051 302222k2 5% 0,062W
33054822 051 3068968R 5% 0,063W
33064822 051 301021k 5% 0,062W
33074822 051 301021k 5% 0,062W
33084822 051 302222k2 5% 0,062W
33104822 051 301021k 5% 0,062W
33114822 051 301021k 5% 0,062W
33124822 051 301021k 5% 0,062W
33134822 051 301021k 5% 0,062W
33144822 051 301021k 5% 0,062W
33154822 051 301021k 5% 0,062W
33164822 051 301021k 5% 0,062W
33174822 051 301021k 5% 0,062W
33184822 051 306826k8 5% 0,062W
33194822 051 3010310k 5% 0,062W
33204822 051 306826k8 5% 0,062W
33214822 051 3010310k 5% 0,062W
33224822 051 3068968R 5% 0,063W
33244822 051 301021k 5% 0,062W
33254822 051 301021k 5% 0,062W
33264822 051 301021k 5% 0,062W
33274822 051 302222k2 5% 0,062W
33284822 051 301021k 5% 0,062W
33294822 051 301021k 5% 0,062W
33334822 051 301021k 5% 0,062W
33344822 051 301021k 5% 0,062W
33354822 051 301021k 5% 0,062W
33364822 051 3068968R 5% 0,063W
33374822 051 301021k 5% 0,062W
33384822 051 301021k 5% 0,062W
33394822 051 301021k 5% 0,062W
33404822 051 306826k8 5% 0,062W
33414822 051 3010310k 5% 0,062WTwin-SW
33424822 051 301021k 5% 0,062W
33434822 051 306826k8 5% 0,062W
33474822 051 3010310k 5% 0,062W
33494822 117 129028k2 1% 0,063W
33554822 051 30681680R 5% 0,062W
33564822 051 30101100R 5% 0,062W
33574822 117 13632100k 1% 0,62W
33594822 117 1292547k 1% 0,063W
33684822 051 30101100R 5% 0,062W
33694822 051 30101100R 5% 0,062W
33704822 051 30101100R 5% 0,062W
34004822 051 30471470R 5% 0,062W
34014822 051 30471470R 5% 0,062WScart
34024822 117 129028k2 1% 0,063WScart
34034822 051 3022322k 5% 0,062WScart
34044822 117 129028k2 1% 0,063WScart
34054822 051 3022322k 5% 0,062WScart
34114822 051 30271270R 5% 0,062W
34134822 051 3047947R 5% 0,063W
34144822 051 3033933R 5% 0,063WScart
34154822 051 3068968R 5% 0,063WScart
34164822 051 30101100R 5% 0,062WScart
34174822 117 118171k2 5% 0,062WScart
34184822 051 3068968R 5% 0,063WScart
34194822 117 118171k2 1% 1/16WScart
34204822 051 30101100R 5% 0,062WScart
34244822 051 3068968R 5% 0,063W
Scart
Scart
34254822 051 3068968R 5% 0,063W
34264822 051 3068968R 5% 0,063W
34274822 051 3068968R 5% 0,063W
34284822 051 3068968R 5% 0,063W
34304822 051 3068968R 5% 0,063W
Scart
34314822 051 30101100R 5% 0,062W
34324822 117 118171k2 1% 1/16W
34334822 051 3068968R 5% 0,063WScart
34344822 051 30101100R 5% 0,062W
34354822 117 118171k2 1% 1/16W
34374822 051 30101100R 5% 0,062WScart
34384822 051 302222k2 5% 0,062WScart
34414822 051 30471470R 5% 0,062W
34424822 051 30471470R 5% 0,062W
34444822 051 3033933R 5% 0,062W
34454822 051 30151150R 5% 0,062W
34474822 051 30101100R 5% 0,062W
34484822 117 118171k2 1% 1/16W
34494822 051 30101100R 5% 0,062W
34504822 117 118171k2 1% 1/16W
34514822 051 3015315k 5% 0,062W
34524822 051 3015315k 5% 0,062W
34544822 117 1292547k 1% 0,063W
34554822 117 1292547k 1% 0,063W
34564822 051 3015315k 5% 0,062W
34574822 117 1292547k 1% 0,063W
34584822 051 3015315k 5% 0,062W
34594822 117 1292547k 1% 0,063W
34604822 051 3010310k 5% 0,062WScart
34614822 117 1292547k 1% 0,063WScart
34624822 117 1292547k 1% 0,063WScart
34634822 051 302222k2 5% 0,062WScart
34644822 051 302222k2 5% 0,062WScart
34654822 051 301021k 5% 0,062WScart
34664822 051 301021k 5% 0,062WScart
34674822 117 1292547k 1% 0,063WScart
34684822 117 1292547k 1% 0,063WScart
34724822 052 104784R7 5% 0,33W
34734822 051 3010310k 5% 0,062W
34744822 051 3010310k 5% 0,062W
34804822 052 104784R7 5% 0,33W
41034822 051 300080R Jumper 0603
41044822 051 300080R Jumper 0603
41074822 051 300080R Jumper 0603
41094822 051 300080R Jumper 0603
41114822 051 300080R Jumper 0603
41124822 051 300080R Jumper 0603
41144822 051 300080R Jumper 0603
41164822 051 300080R Jumper 0603
41214822 051 300080R Jumper 0603
41234822 051 300080R Jumper 0603
41914822 051 300080R Jumper 0603
9-189-18
ELECTRICAL PARTS LIST - AV BOARD
RESISTORS
41924822 051 300080R Jumper 0603
41954822 051 300080R Jumper 0603
42004822 051 300080R Jumper 0603
42014822 051 300080R Jumper 0603
42054822 051 300080R Jumper 0603
42064822 051 300080R Jumper 0603
42094822 051 300080R Jumper 0603
non-Kara
43414822 051 300080R Jumper 0603
43424822 051 300080R Jumper 0603
44004822 051 300080R Jumper 0603
44044822 051 300080R Jumper 0603
Non-Scart
44054822 051 300080R Jumper 0603
44064822 051 300080R Jumper 0603
44074822 051 300080R Jumper 0603
44084822 051 300080R Jumper 0603
Scart
44094822 051 300080R Jumper 0603
44104822 051 300080R Jumper 0603
Non-Scart
44114822 051 300080R Jumper 0603
44124822 051 300080R Jumper 0603
44144822 051 300080R Jumper 0603Scart
44154822 051 300080R Jumper 0603
44164822 051 300080R Jumper 0603
44204822 051 300080R Jumper 0603Scart
44214822 051 300080R Jumper 0603
44244822 051 300080R Jumper 0603
44254822 051 300080R Jumper 0603
44264822 051 300080R Jumper 0603
44274822 051 300080R Jumper 0603
44284822 051 300080R Jumper 0603
44304822 051 300080R Jumper 0603Scart
44334822 051 300080R Jumper 0603Scart
44364822 051 300080R Jumper 0603Scart
45004822 051 300080R Jumper 0603
45014822 051 300080R Jumper 0603
45024822 051 300080R Jumper 0603
45034822 051 300080R Jumper 0603
45044822 051 300080R Jumper 0603
45054822 051 300080R Jumper 0603
45064822 051 300080R Jumper 0603
45074822 051 300080R Jumper 0603
45084822 051 300080R Jumper 0603
45094822 051 300080R Jumper 0603
45104822 051 300080R Jumper 0603
45114822 051 300080R Jumper 0603
45124822 051 300080R Jumper 0603
45134822 051 300080R Jumper 0603
45144822 051 300080R Jumper 0603
45154822 051 300080R Jumper 0603
45164822 051 300080R Jumper 0603
45174822 051 300080R Jumper 0603
45184822 051 300080R Jumper 0603
45194822 051 300080R Jumper 0603
45204822 051 300080R Jumper 0603
45214822 051 300080R Jumper 0603
45224822 051 300080R Jumper 0603
45234822 051 300080R Jumper 0603
45244822 051 300080R Jumper 0603
45254822 051 300080R Jumper 0603
45264822 051 300080R Jumper 0603
45274822 051 300080R Jumper 0603
45284822 051 300080R Jumper 0603
45294822 051 300080R Jumper 0603
45304822 051 300080R Jumper 0603
45314822 051 300080R Jumper 0603
45324822 051 300080R Jumper 0603
45334822 051 300080R Jumper 0603
45344822 051 300080R Jumper 0603
45354822 051 300080R Jumper 0603
45364822 051 300080R Jumper 0603
45374822 051 300080R Jumper 0603
45384822 051 300080R Jumper 0603
45394822 051 300080R Jumper 0603
45404822 051 300080R Jumper 0603
45414822 051 300080R Jumper 0603
45424822 051 300080R Jumper 0603
45434822 051 300080R Jumper 0603
45444822 051 300080R Jumper 0603
45454822 051 300080R Jumper 0603
45464822 051 300080R Jumper 0603
45474822 051 300080R Jumper 0603
45484822 051 300080R Jumper 0603
45494822 051 300080R Jumper 0603
45504822 051 300080R Jumper 0603
45514822 051 300080R Jumper 0603
45524822 051 300080R Jumper 0603
45534822 051 300080R Jumper 0603
45544822 051 300080R Jumper 0603
45554822 051 300080R Jumper 0603
45564822 051 300080R Jumper 0603
45574822 051 300080R Jumper 0603
45584822 051 300080R Jumper 0603
45594822 051 300080R Jumper 0603
45604822 051 300080R Jumper 0603
45644822 051 300080R Jumper 0603
45794822 051 300080R Jumper 0603
45854822 051 300080R Jumper 0603
45934822 051 300080R Jumper 0603
45984822 051 300080R Jumper 0603
45994822 051 300080R Jumper 0603
46534822 051 300080R Jumper 0603
COILS & FILTERS
52012422 536 00548Fixed Ind, 100uH 15%
52324822 157 105862,2uH 10%
ELECTRICAL PARTS LIST - AV BOARD
54014822 157 105862,2uH 10%
54024822 157 70601Inductor 100uH
DIODES
61014822 130 61219BZX79-B10
62004822 130 11397BAS316
62014822 130 11397BAS316
62024822 130 10871SBYV27-200
62059322 128 70685SS14
62234822 130 318781N4003G
62244822 130 34278BZX79-B6V8
62254822 130 318781N4003G
62274822 130 11397BAS316
62284822 130 11397BAS316
TRANSISTORS & INTEGRATED CIRCUITS
71005322 130 60159BC847B
71014822 130 60373BC857B
71309322 150 74668TDA7468D
71314822 130 40959BC547B
71324822 130 60373BC857B
Scart
71334822 130 42804BC817-25
71505322 130 60159BC847B
72004822 130 42804BC817-25
72044822 130 63166BD242B
72064822 130 40995BD438
72073198 010 42310BC847BW
72084822 130 40995BD438
72093198 010 42310BC847BW
72109322 188 75682LM2576T-3,3
72113198 010 42310BC847BW
72304822 209 31378NJM4556MB
72314822 130 60373BC857B
72325322 130 60159BC847B
72335322 130 60159BC847B
72504822 130 42804BC817-25
72524822 130 60373BC857B
72535322 130 60159BC847B
73015322 130 60159BC847B
73024822 130 60373BC857B
73049322 150 74668TDA7468D
73309322 150 74668TDA7468D
73529337 148 2065374HC4051D
74024822 209 17345M62320FP
74055322 130 60159BC847B
74065322 130 60159BC847B
74075322 130 60159BC847B
Scart
74105322 130 60159BC847BScart
74115322 130 60159BC847BScart
74215322 130 60159BC847B
74225322 209 11102HEF4052BT
74235322 130 60159BC847B
74514822 130 42804BC817-25
74524822 130 42804BC817-25
74544822 130 42804BC817-25
Scart
74555322 130 60159BC847BScart
74565322 130 60159BC847BScart
Note: Only the parts mentioned in this list are normal service
This assembly drawing shows a summary
of all possible versions.
For components used in a specific version
see schematic diagram respectively partslist.
Servo Ampliers & Motor Drives Circuit Diagram .......................... 11-8
CD/DVD ROM Controller Circuit Diagarm ................................... 11-9
Electrical parts list ......................................................................11-10
DQ0-DQ7Data Inputs/Outputs
EChip Enable
GOutput Enable
WWrite Enable
M29F002BT, M29F002BB:
RP
V
V
CC
SS
Reset/Block Temporary Unprotec t
M29F002BNT, M29F002BNB:
Not Connected Internally
Supply Voltage
Ground
11-2
11-2
Data Separator
Built-in data slicer and data PLL for data
recovery from RF signal.
Supports digital/analog slice level
adjustment.
Built-in auto calibration function.
Built-in auto wire range control function.
DVD-DSP
Built-in synchronous pattern/ID detection
/protection/separation.
Built-in EFM+ (8 to 16) demodulation
circuit.
Built-in high performance RSPC ECC
circuit.
Supports up to 6X DVD-ROM system with
ECC correcting “on the fly”.
Built-in descrambler/EDC circuit.
CD-DSP
Synchronous pattern detection, protection
and interpolation.
Built-in EFM demodulation circuit,
subcode demodulation circuit.
Dual C1 correction and quadrule C2
correction.
Subcode Q data can output with audio
data synchronously.
Digital Servo
Built-in A/D and D/A converters for servo
control signals processing.
Built-in digital controller for focus,
tracking servo control of CD/DVD systems.
Built-in CLV/CAV auxiliary function for
spindle servo control.
Built-in “Seek Sensor” auxiliary circuit for
seek control.
Automatic adjustment of focus servo and
tracking servo, for loop gain, offset and
balance.
Built-in RF gain automatic adjustment
function.
Built-in AFC circuit and APC circuit for CLV
and AFC circuit for CAV spindle servo of
CD/DVD systems.
Built-in defect and shock protection
function.
DRAM Interface
Supports up to 16 Mb EDO DRAM and
SDRAM.
Separate buffer address pointers and
automatic address calculation that save
firmware effort.
Read-ahead cache scheme for multimedia
isochronous transfer.
Protection logic preventing uncorrected
sectors being released to the host.
Target Search
Built-in target sector searching circuit
for auto-searching the target sector.
Automatic data buffering after the
target sector has been located.
C3 ECC/EDC
Programmable Reed-Solomon Product
Code (RSPC) that allows different error
correction schemes for CD-ROM.
Built-in On-chip EDC function.
Support up to 32X CD-ROM system with
ECC correcting “on the fly”.
Host Interface
Supports ATA PIO mode 4 timing
Supports Multiword DMA mode 2 timing
Compliant with SFF-8020(ATAPI) 2.5,
ATA 3(Overlapping feature), and
SFF-8090 (ATAPI for DVD) standard
High current drivers with slew rate
control for direct connecting to the ATA
bus and noise immunity.
Automatic Read Control Circuit for host
data transfer.
Automatic wake up from power down on
host reset or command write
Automatic sequence for packet command
receiving and Automatic updating of the
host task file registers
Supports ATAPI write command that can
let user update firmware from PC.
Built-in authentication circuit for copy
protection.
Multiplexed MPEG decoder interface
(local bus).
Microcontroller Interface
Embedded microcontroller compatible
with Intel 8032 command set
Supports Intel 8032 series MCUs
Supports Intel 8032 series MCUs and
Hitachi H8 series MCUs.
Supports automatically download
firmware function directly from ATAPI
interface to flash memory
Supports “on-system” upgrade flash
memory function from CD-R discs or ATAPI
interface
High speed register (buffer RAM) access to
meet the requirement of high
performance system
Supports Direct mapped access to the
buffer RAM using ready bit handshaking
M5705 (Ali) ApplicationM5705 (Ali) Features
M
Motor
Driver
M5703/M5707
RF
Amp
M5705
Data
Separator
Digital
Servo
DVD-DSP
CD-DSP
4M DRAM
RAM
Arbiter
Target
Search
ATAPI
&
MPEG
I/F
C3 ECC
EDC
MCU
ROM
PC
MPEG
DEC.
M5705 Pins Descriptions
11-3
11-3
Pin Name Pin No. Type Description
Servo Data Slicer Interface Pins
XSRFIN 2 I / A Analog RF signal input after passing through the equalizer.
XSIPIN 3 I / A Inverting input pin of data slicer.
XSDSSLV 5 O / A Slice level output pin.
XSRSLINT 6 I / A Reference current setting pin for analog data slicer.
Servo DAC Interface Pins
XSAWRC 8 O / A Output for enlarge VCO range. Analog output from DAC buffer.
XSRFGC 9 O / A RF gain control output.
XSEFGC 10 O / A E,F gain control output.
XSFOCUS 11 O / A Output voltage level for focusing buffer IC.
XSTRACK 12 O / A Output voltage level for tracking buffer IC.
XSSLEG 13 O / A Output voltage level for sledge buffer IC.
XSMOTOR 15 O / A Output v oltage level for spindle motor buffer IC.
Servo Comparator Interface Pins
XSRFRPLP 17 I / A High bandwidth low pass filter input for RFRP.
XSTELP 18 I / A High bandwidth low pass filter input for TE.
Servo ADC Interface Pins
XSVREF2 1 9 I / A 2.1 V reference voltage input.
XSRFRP 20 I / A RF ripple/envelope signal input.
XSTEXI 21 I / A Tracking zero crossing input signal.
XSTEI 23 I / A Tracking error input signal.
XSFEI 24 I / A Focus error input signal.
XSCEI 25 I / A 1. Center error input signal.
2. Photo Interrupt Input.
XSSBAD 2 7 I / A Sub-beam addition signal input.
Servo PLL Interface Pins
XSPDIREF 166 I / A Phase detector reference current generator. Connect a resistor between this
pin and ground to set reference current.
XSFDIREF 167 I / A Frequency detector reference current generator. Connect a resistor between
this pin and ground to set reference current.
XSPLLFTR2 169 I / A Data PLL loop filter pin #2.
XSFDO 171 O / A Output node of frequency detector charge pump circuit.
XSFTROPI 172 I / A Input node of loop filter OP circuit.
XSVR_PLL 173 I / A PLL reference voltage input.
XSPDOFTR2 174 I / A Phase detector filter pin #1.
XSVREFO 175 O / A Reference voltage output.
XSAWRCVCO 176 I / A Auto Wide Range Control VCO input pin. For enlarge VCO range in CAV mode.
Servo Control Interface Pins
XSDFCT 29 I Defect detection signal input.
XSCSJ 30 O Chip select signal for accessing control registers.
XSCLK 31 O Clock output for accessing control registers.
XSDATA 32 I/O Registers data input/output pin.
XSLDC 33 O Laser diode on/off control output for both CD/DVD.
XSFGIN 34 I Motor Hall sensor input.
XSSPDON 35 O Spindle motor on output.
XSFLAG[3:0] 36,37,
38,39
O These pins are used to monitor some status of servo control block.
Pin Name Pin No. Type Description
Microcontroller Interface Pins
XGPIO[2:0] 48,51,5
2
XMP1_7 40 I/O Internal microcontroller programmable I/O port 1.7.
XMP1_6 41 I/O Internal microcontroller programmable I/O port 1.6.
XMP1_5 43 I/O This pin is now changed to be NC.
XMP1_4 44 I/O Internal microcontroller programmable I/O port 1.4.
XMP1_3 45 I/O Internal microcontroller programmable I/O port 1.3.
XMP1_2 47 I/O Internal microcontroller programmable I/O port 1.2.
XMP1_1 49 I/O Internal microcontroller programmable I/O port 1.1.
XMP1_0 57 I/O Internal microcontroller programmable I/O port 1.0.
XMFSCSJ 46 I/O Output chip select connected to external flash ROM chip enable pin.
XMPSENJ 54 I/O Output program store enable connected to external ROM PSENJ pin.
XMALE 56 I/O This signal is used as address latch signal in address/data mux mode.
XMCSJ 70 I/O 1. This signal must be asserted for all microcontroller accesses to the
XMRDJ 71 I/O 1. This signal is used as the Read Strobe signal.
XMWRJ 72 I/O This signal is used as the Write Strobe signal.
XMINT1J 73 I/O 1. This signal is an interrupt line to the microcontroller.
I/O 1. These pins are used as general purpose I/O bus.
2. When use internal microcontroller, XGPIO[2] can be used as programmable
I/O port 3.6.
This pin is default used as the A16 (microcontroller address line 16).
registers of this chip.
2. When use internal microcontroller, this signal can be used as
programmable I/O port 3.1.
2. When use internal microcontroller, this signal can be used as
programmable I/O port 3.0.
2. When use internal microcontroller, this signal can be used as
programmable I/O port 3.7.
I/O These pins are used as address bus.
I/O These pins are used as data bus for the 16-bit processor mode, or the
address/data mux bus for the 8-bit processor mode.
Miscellaneous Pins
XTPLCK 163 I/O PLCK test pin.
XTSLRF 164 I/O SLRF test pin.
XOSC1 59 I Crystal input/ System clock. The input frequency from outside crystal or
oscillator is 33.8688Mhz.
XOSC2 60 O Crystal output.
XCRSTJ 53 I Chip Reset. An asserted low input generates a component reset that stops all
operations within the chip and deasserts all output signals. All input/output
signals are set to input.
M5705 Pins Descriptions
11-4
11-4
Pin Name Pin No. Type Description
Host Interface Pins
XHCS1J 94 I This pin is used to select the command block task file registers.
XHCS3J 93 I This pin is used to select the control block task file registers.
XHIORJ 103 I Asserted by the host during a host I/O read operation.
XHIOWJ 104 I Asserted by the host during a host I/O write operation.
XHDRQ 105 O 1. DMA request. This pin is configured as the DMA request signal, and is
used during DMA transfer between the host and the controller. This pin is
tri-stated when DMA transfers are not enabled.
2. MPEG acknowledge. This pin is used as the ACKJ signal when MPEG
interface mode is selected.
XHDACKJ 101 I 1. DMA acknowledge. This pin is configured as DACKJ, and is used as the
DMA acknowledge signal during DMA data transfers.
2. MPEG request. This pin is used as the REQ signal when MPEG interface
mode is selected.
XHCS16J 99 O 1. 16-bit data select. This signal indicates that a 16-bit data transfer is active
on the host data bus. This pin is open-drain tri-state output.
2. MPEG clock. This pin is used as the CLOCK signal when MPEG interface
mode is selected.
XHRSTJ 50 I Host Reset. The reset of ATA bus
XHINT 100 O 1. Host interrupt request. This tri-state pin is the host interrupt request, and
is asserted to indicate to the host that the controller needs attention.
2. MPEG begin. This pin is us ed as the BEGIN signal when MPEG interface
mode is selected.
XHPDIAGJ 97 I/O This pin is used as the Passed Diagnostics signal, and may be an input or an
open-drain output.
XHDASPJ 92 I/O This pin is used as the Drive Active/ Slave Present s ignal, and is an input or an
open-drain output. This pin is used for Master/Slave drive communication
and/or for driving an LED.
XHIORDY 102 O 1. I/O channel ready. This signal is driven low to extend host transfer cycles
when the controller is not ready to respond. This pin will be tri-stated when a
read or write is not in progress.
2. MPEG error. This pin is us ed as the ERROR signal when MPEG interface
mode is selected.
XHA[2:0] 95, 98, 96 I Host address lines. The host address lines A[2:0] are used to access the
various host control, status, and data registers.
XHD[15:0] 106, 108,
I/O 1. Host data bus. This bus is used to transfer data and status between the
host and the controller.
2. MPEG data bus 7-0. The HD[7:0] are us ed as the DATA[7:0] when MPEG
interface mode is selected.
3. VCD I/F. Bit3-0 are used as VCD I/F signal when VCD function is enabled.
The relationship of bit3-0 and VCD I/F is as follow.
HD0
HD1
HD2
HD3
CD-DATA
CD-LRCK
CD-BCK
CD-C2PO
Pin Name Pin No. Type Description
RAM Interface Pins
XRSDCLK 143 O This signal is the clock output for SDRAM.
XROEJ 147 O This signal is used as the memory output enable for external DRAM buffers.
After RSTJ is asserted, this signal will be low.
XRWEJ 142 O This signal is asserted low when a buffer memory write operation is active.
XRRASJ 144 O This signal is used as Row address output to external DRAM buffer. After
RSTJ is asserted, this signal will be high.
XRCASJ 145 O This signal is used as column address output to external DRAM. After RSTJ is
asserted, this signal will be high.
XRA[11:0] 151, 152,
AVDD5_DS 4 Analog Power +5V for Data Slicer part.
AVDD5_DA 14 Analog Power +5V for DAC part.
AVDD5_AD 26 Analog Power +5V for ADC part.
AVDD5_PL 168 Analog Power +5V for Data PLL part.
VDD 7,55,58,
76,115,
146,150,
162
AVSS_DS 1 Analog Ground for Data Slicer part.
AVSS_DA 16 Analog Ground for DAC part.
AVSS_AD 22 Analog Ground for ADC part.
AVSS_PL 170 Analog Ground for Data PLL part.
GND 28,42,61,