Philio Technology PSE02 User Manual

Multi Sound Siren PSE02

The multi sound siren PSE02 is a wireless siren, based on Z-Wave

TM

technology. Z-WaveTM is a wireless communication protocol designed
for home automation, specifically to remotely control applications in
residential and light commercial environments. The technology uses a
low-power RF radio embedded or retrofitted into home electronics
devices and systems, such as lighting, home access control,
entertainment systems and household appliances.

This device is one component of the Z-WaveTM system and is designed
to work with all other Z-WaveTM enabled devices in a home control
network. The device adopt the Z-WaveTM 400 series chip, when your Z­WaveTM network system is all made by Z-WaveTM 400 series devices. The
network system will have the advantages as below.

• Concurrent multi-channel support reduces external interference.

• Better RF range, improve about 10 meters in indoor.

• Support 100 Kbps transmit speed, speed up communication.

Product Overview

Adding to Z-WaveTM Network

There are one tamper key behind the device. It could inclusion,
exclusion, reset or association from Z-WaveTM network.

In the first time, add the device into the Z-WaveTM network. First, make
sure the primary controller is in the inclusion mode. And then power on
the device. The device will auto start the NWI (Network Wide Inclusion)
mode. And it should be included in 5 seconds. You will see the LED
light ON one second.

Function

Description

Inclusion

1. Have Z-WaveTM Controller entered inclusion mode.

2. Pressing tamper key three times within 1.5 seconds
will enter inclusion mode.

3. After inclusion successful, the device will wake to
receive the setting command from Z-WaveTM
Controller about 20 seconds.

1

Siren

Tamper Key

Circle Button

Battery

(Optional)

DC Jack

Exclusion

1. Have Z-WaveTM Controller entered exclusion mode.

2. Pressing tamper key three times within 1.5 seconds
will enter exclusion mode.
Node ID has been excluded.

Reset

1. Pressing tamper key four times within 1.5 seconds
and do not release the tamper key in the 4th
pressed, and the LED will turn ON.

2. After 3 seconds the LED will turn OFF, after that
within 2 seconds, release the tamper key. If
successful, the LED will light ON one second.
Otherwise, the LED will flash once.

3. IDs are excluded and all settings will reset to
factory default.

Association

1. Have Z-WaveTM Controller entered association
mode.

2. Pressing tamper key three times within 1.5 seconds
will enter association mode.

Note: The device support 6 groups.
The group 1 is for receiving the report message, like
tamper event.
The group 2 to 6 will map to different sound, when the
device got the BASIC Set 0xFF, it will check is the node
in which group, and play the mapping sound.
The group 2 mapping to emergency alarm.
The group 3 mapping to fire alert.
The group 4 mapping to ambulance sound.
The group 5 mapping to police car sound.
The group 6 mapping to door chime.

• Including a node ID allocated by Z-WaveTM Controller means
inclusion. Excluding a node ID allocated by Z-WaveTM
Controller means exclusion.

• Failed or success in including/excluding the node ID can be
viewed from Z-WaveTM Controller.

Notice 1: Always RESET a Z-WaveTM device before trying to add it to a
Z-WaveTM network.

Notice 2: When the device into NWI mode, any tamper key and
sensor functionality will useless. The NWI will timeout after 3 minutes.

Z-WaveTM Message Report

* Tamper Report:

When the tamper key is pressed over 5 seconds. The device will into
the alarm state. In that state, if the tamper key be released, the device
will unsolicited to send the “Sensor Binary Report” to the nodes in the
group 1.
Sensor Type: Tamper (0x08)
Sensor Value: 0xFF

* Siren Alarm State Report:

When the siren start playing or stop the alarm sounds, the device will
unsolicited to send the “Sensor Binary Report” to the nodes in the
group 1.
Sensor Type: General Purpose (0x01)
Sensor Value: 0xFF (Start play), or 0x00 (Stop play)

Power Up Procedure

When the power on, the device will check is it already adding to the
network? If doesn't, it will auto start the NWI mode. The LED will flash
in every second and continue 3 minutes. Until timeout or the device
successful to inclusion by controller.

2