Philio Technology PAN26 User Manual

PAN26
Smart Touch In-Wall Switch

Note: The power cord must meet 1.25mm² or 16AWG or better

Introduction

All the control you want is just a few dongles away
Philio’s patent pending Smart touch in-wall Switch is the world’s first true smart
electric switch that does so much in so little in-wall space. It comes with empty relays,
but the magic happens when plug n’ play dongles are inserted into it: On/off lights,
dimmers, shutters and relays. From now on you can control everything from one
elegant in-wall switch at your home or office; or use it as a regular switch because it
has such a refined appearance.

This in-wall switch PAN26 is a security enabled wireless device, based on Z-Wave
Plus technology. Z-Wave PlusTM enabled devices displaying the Z-Wave PlusTM logo
can also be used with it regardless of the manufacturer, and can also be used in other
manufacturer’s Z-WaveTM enabled networks. Remote On/Off control of the switch is
possible with other manufacturer’s wireless Controller. PAN26 is designed to act as a
repeater. Repeaters will re-transmit the RF signal to ensure that the signal is received
by its intended destination by routing the signal around obstacles and radio dead
spots. Because PAN26 supports Security Command Class, it can learn with Secured
controller. Its functionality and supported command classes is identical when included
as a secure and non-secure device.

Safety Precautions and Installation

• Avoid installing the unit in storming or raining weather.

• Be sure to isolate or switch off power source before installing or maintenance.

• Do ensure that the power supply circuit protected by a 16A circuit breaker or

suitable equivalent fuse.

IMPORTANT

• Installation must be performed by skilled technicians who are informed about
the standards and technical requirements of the appliance and its proper
installation.

• Check your local codes as they apply to your situation. If the house wiring is
of aluminum, consult with an electrician about proper wiring methods.

Before proceeding with the installation, TURN OFF THE POWER TO THE LIGHTING
CIRCUIT AT THE CIRCUIT BREAKER OR FUSE BOX TO AVOID ELECTRICAL
SHOCK.

1

Adding to Z-WaveTM Network

Annotation

1.



In the front casing, there is an on/off button with LED indicator below which is used to
toggle switch on and off or carry out inclusion, exclusion, reset or association. When
first power is applied, its LED flashes on and off alternately and repeatedly at 0.5
second intervals. It implies that it has not been assigned a node ID and start auto
inclusion.

Auto Inclusion
The function of auto inclusion will be executed as long as the in-wall switch does not

have Node ID and just connect the switch to main power.
Note: Auto inclusion timeout is 2 minutes during which the node information of

explorer frame will be emitted once every several seconds. Unlike “inclusion” function
as shown in the table below, the execution of auto inclusion is free from pressing the
On/Off button on the Switch.

The table below lists an operation summary of basic Z-Wave functions. Please refer to
the instructions for your Z-WaveTM Certificated Primary Controller to access the Setup
function, and to include/exclude/associate devices

Function

No node ID

Inclusion

Exclusion

The Z-Wave Controller does not allocate
a node ID to the Switch.

1. Put your Z-Wave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.

2. Pressing INCLUDE_BUTTON (No.5)
three times within 1.5 seconds will
enter inclusion mode.

1. Put your Z-Wave controller into
exclusion mode by following the
instructions provided by the

controller manufacturer.
Pressing INCLUDE_BUTTON
(No.5) three times within 1.5
seconds will enter exclusion mode.

Description

LED 1.5-second on,

1.5-second off
One press one flash LED

One press one flash LED

3. Node ID has been excluded.

Reset

Association

Including a node ID allocated by Z-Wave Controller means inclusion. Excluding a node
ID allocated by Z-Wave Controller means exclusion.



Failed or success in including/excluding the node ID can be viewed from the Z-Wave

Controller.

1.

Pressing INCLUDE_BUTTON
(No.5) three times within 2 seconds
will enter inclusion mode.

2.

Within 1 second, press On/Off
button again for 5 seconds.

3.

IDs are excluded.

1. The PAN26 is an always listening
Z-Wave device, so associations
be added or removed by a controller
at any time.

Or If your controller requires to have

the PAN26 send a 'node information
frame' or NIF for associations,
pressing the On/Off button three
times within 2 seconds will cause
the PAN26 to send its NIF.

2. There are 4 groups for the switch

Z-Wave Supported Command Class:

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2

• COMMAND_CLASS_CONFIGURATION

• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

• COMMAND_CLASS_VERSION_V2

• COMMAND_CLASS_ASSOCIATION_GRP_INFO

• COMMAND_CLASS_POWERLEVEL

• COMMAND_CLASS_DEVICE_RESET_LOCALLY

• COMMAND_CLASS_SECURITY

2

LED 0.5s On, 0.5s Off
(Enter auto inclusion)

Use this procedure only in
the event that the primary
controller is lost or
otherwise inoperable.

LED 0.5s On, 0.5s Off
(Enter auto inclusion)
LED one press one flash

Overview

A. LED indication (1-9 button).
B. RJ11 connector x 2.
C. switch or dimmer dongles (operational).

Installation and Operation

Assembly steps:

1. Open the back cover (1) and insert the dongle (figure 1)

2. Move the panel (3) upwards (Figure 2) and remove it (Figure 3)

3. Install the body (5) in the power distribution box and lock the screws (figure 4)

4. Cover the panel (3) (figure 5) and press down (figure 6)

5. Disassembly can be done in the opposite way

To start using PAN26 Smart touch in-wall Switch, please connect the device to power
by L and N.

You also need a PSC03/PAN27 Philio Gateway to connect

1. Connect power cable to the L and N, and you will see all button
will turn as Blue

2. Installing the companion APP

2.1 Connect your phone to Internet, login or sign up for google account or APP ID

2.2 Launch Play store or APPLE store

2.3 Search for Philio Home Mate2, then install the companion app.

2.4 Click the APP and you can use local LAN search or QR code to find
Philio Gateway

3