Philio Technology PAN05 User Manual

PAN05-1/-2/-3

In Wall Single relay(1 way) switch module

P

Fig 1. Assembling

This in-wall switch module is a transceiver which is a Z-WaveTM enabled device and

is fully compatible with any Z-WaveTM enabled network. Mini size design let the

module can easily hide itself into the wall box and that will be good for the house

decoration.

There are many kind of application by using the module to switch Load On and Off ,

one main application is the light control. If connect the com port directly to AC Line

terminal ,the new smart relay calibration technology can reduce the inrush current

caused by the load and let the module work perfectly with many kind of light like

incandescent, fluorescent and LED light. This module can also connect to alternative

power supply like DC 12V to switch on/off 12V MR-16 light as follow picture.

Adding to Z-WaveTM Network

In the front casing, there is an on/off button with LED indicator below which is used to

toggle switch on and off or carries out inclusion, exclusion, reset or association. After

being excluded, its LED flashes on and off alternately and repeatedly at 2-second in-

tervals. It implies that it has not been assigned a node ID and cannot work with Z-

Wave enabled devices.

Auto Inclusion

The function of auto inclusion will be executed as long as the in wall switch does not

have Node ID and just connect the switch to main power.

Note: Auto inclusion timeout is 2 minute during which the node information of

explorer frame will be emitted once every 5 seconds. Unlike “inclusion” function as

1

shown in the table below, the execution of auto inclusion is free from pressing the

On/Off button on the Switch.

The table below lists an operation summary of basic Z-Wave functions. Please refer

to the instructions for your Z-WaveTM Certificated Primary Controller to access the

Setup function, and to include/exclude/associate devices

Function Description LED Indication

No node ID The Z-Wave Controller does not allocate

a node ID to the Switch.

2-second on, 2-second off

Inclusion 1. Have Z-Wave Controller entered

inclusion mode.

One press one flash

2. Pressing Include button of PAN05

three times within 2 seconds will

enter inclusion mode.

Exclusion 1. Have Z-Wave Controller entered

exclusion mode.

One press one flash

2. Pressing Include button of PAN05

three times within 2 seconds will

enter exclusion mode.

Node ID has been excluded. 2-second on, 2-second off

Reset 1. Pressing Include button of PAN05

three times within 2 seconds will

enter inclusion mode.

2. Within 1 second, press Include

button of PAN05 again for 5

seconds until LED is off.

3. IDs are excluded.

Association 1. Have Z-Wave Controller entered

association mode.

Or Pressing Include button of PAN05

three times within 2 seconds will

enter association mode

One press one flash

2. There are only 1 group for the switch

※

Including a node ID allocated by Z-Wave Controller means inclusion. Excluding a node

ID allocated by Z-Wave Controller means exclusion.

※

Failed or success in including/excluding the node ID can be viewed from the Z-Wave

Controller.

Sometimes people are not easy to execute exclusion or inclusion especially when

PAN05 already installed in a wall box. To solve this issue, PAN05 support a special

feature that can use S1 or S2 to execute “exclusion, inclusion, Reset or Association”

at the first 3 minutes when first time connect to main power.

LED Indication

To distinguish what mode the switch is in, view from the LED for identification.

State Type LED Indication

Normal Whenever we switch On and off of the PAN05 by S1 S2 or On/Off

button or RF command , the LED will lights up 1 second and then

2

off.

No node ID Under normal operation, when the Switch has not been allocated a

node ID, the LED flashes on and off alternately at 2-second

intervals. By pressing S1 S2 or On/Off button, it will stop flashing

temporarily. However, after disconnect and reconnect the Switch,

the LED will flash on and off alternately at 2-second intervals.

Learning When PAB01 is in learning mode, LED flashes on and off

alternately and repeatedly at 0.5 second intervals.

Choosing a Suitable Location

1. Do not locate the Switch facing direct sunlight, humid or dusty place.

2. The suitable ambient temperature for the Switch is 0°C~40°C.

3. Do not locate the Switch where exists combustible substances or any source of

heat, e.g. fires, radiators, boiler etc.

4. After putting it into use, the body of Switch will become a little bit hot of which

phenomenon is normal.

Installation

1. Put the in wall switch into a wall box and connect the AC power wire L,N to

PAN05 connector L, N.

2. Connect the wall switch to the PAN05 as Fig1 .

3. There are 3 mode PAN05 can be configured to match different kind of wall

switch, please refer to 3-1 Edge / Pulse / Edge-Toggle mode which described

in next section of this user manual.

4. If Edge-Toggle mode has been set, and the S1 S2 is connect to normal bi-stable

switch, every time when change the state of the wall switch will also swap the

state of Relay1.

Programming

1. Basic Command Class / Binary Switch Command Class

The Switch will respond to BASIC and BINARY commands that are part of the Z-

3