Pentax TS3V310ED, TS2V214AEDW, TS3V310E, HS2V616E, HS2V616ED Owners manual

ENGLISH ON THE BACK

■

DC

TS2V214AED TS2V214AEDW TS3V310ED TS3V310EDW HS2V616ED

TS2V214AE

TS3V310E

HS2V616E

います。ご使用の前にこの取扱説明書を必ずお読みいただき、正しくお使いく ださい。お読みになった後は、いつでも見られるところに保管してください。

■

とを示す」内容です。

2 36 9 174-8639

Tel.[phone] Fax.[phone]

3160635-Z2-1 (J) S3095072

■

•-

■

ありますので、カメラの取扱説明書をご覧ください。

•cm

°

■

カメラの自動絞り方式をご確認ください。

1		-
2		+
3		+
4		-
JEITA EIAJ RC-5204
1
2	―	――――
3
4

EIAJ RC-5204

■

遠端、広角端のどちらかでピントが合わせられない場合は、カメラの 取扱説明書をご覧になり次の手順でカメラのバックフォーカスを調整 してください。

ださい。

にし、カメラのバックフォーカスを調整しピントを合わせてくだ さい。

を行い、ピント合わせが可能か確認してください。

	■	■
	HS2V TS2V
			H
	TS3V
			L

ださい。

			■
			■
			■
			CE EU
			EMC EN50130-4 EN55022
	■
		.
		.	.	.
		.	.
				Ω±
				Ω±
		. p-p . p-p
		±		.

Auto-Iris Vari-Focal Lens Operating Instructions

■ Model number

DC drive iris type

TS2V214AED TS2V214AEDW TS3V310ED TS3V310EDW HS2V616ED

Video drive iris type

TS2V214AE

TS3V310E

HS2V616E

Thank you for choosing PENTAX CCTV lenses. Before operating this lens, please read these instructions carefully. After reading this Operating Instructions, keep it for future reference.

■ For your safety on use of a lens

Before operating, pay special attention to the following remarks.

WARNING	CAUTION
This alerts users to the possible	This alerts users to the possible risk
risk of personal harm.	of personal and material harm.

This is a warning to users.

This is to caution users.

WARNING

Do not look at the sun through the lens with the naked eye. Loss of eyesight may occur.

Do not disassemble, repair or modify the lens.

Fire, electric shocks or malfunction may occur.

Do not input any improper power to the cable. Fire, electric shocks or malfunction may occur.

If the lens emits smoke, smells of smoke or gives off heat, discontinue use immediately. Fire or electric shocks may occur.

Do not damage, bend, twist or pull on the cable. Fire, electric shocks or malfunction may occur.

CAUTION

Do not leave unused lenses in direct sunlight. Fire may occur.

Mount the lens firmly on a camera, so that it will not loosen and fall off.

Do not install the lens in a place where vibration and shock are expected. It may come loose and fall off.

HOYA CORPORATION

PENTAX Imaging Systems Division

Security Systems Sales Department

■ Precautions

•Connect the cable properly referring to the following list entitled "Auto-iris cable connections".

•Do not use organic solvents, such as thinners, alcohol or benzine to remove stains from the lens.

•Use a blower or a clean lens brush to remove dust. When grease or fingerprints are on the lens, wipe them off with a lens cleaning paper and lens cleaner gently forming a swirl from the center to the circumference.

•This lens is a precision optical product. Avoid dropping, strong vibration, shock and pressure on it.

•Keep the lens away from dust, poisonous gas, moisture and salt. It may cause lens malfunction.

■ Mounting and removing the lens

Before mounting the lens, confirm the camera mount matches the lens. This is a CS mount lens and is not suitable for a C mount camera. Some cameras are C and CS mount compatible. Refer to the Operating Instructions of the camera.

Screw the lens clockwise into the camera.

Eventually, the clutch of the lens will start slipping. Keep turning the lens until the clutch reaches its stop, and tighten the lens with max. 150N•cm of bolting torque.

The lens position is now adjustable counter-clockwise in about 330°. Turn the lens until the correct position is achieved.

When removing the lens, keep turning the lens counter-clockwise until the lens comes off.

■ Auto-iris cable connections

Installation of the auto iris Cable.

Lenses are available in Video and DC drive Iris Variants.

DC drive iris lens (With 4-pin connector)

Pin No.	Color	Specifications
1	Blue	Damping coil -
2	Red	Damping coil +
3	White	Driving coil +
4	Green	Driving coil -

This pin configuration is conforming to JEITA* Standard.

* Japan Electronics and Information Technology Industries Association

Video drive iris lens (With 4-pin connector)

Pin No.	Color	Specifications
1	Red	Power supply
2	―	――――
3	White	Video signal
4	Black	Ground

This pin configuration is conforming to JEITA* Standard.

■ Adjusting back focus

The flange back of this lens is factory adjusted for CS mount. In case you are unable to focus either at the shortest or longest focal lengths, adjust the back focus of the camera by the following method, referring to the Operating Instructions of the camera.

Fully open the iris by either of the following methods.

Set the electronic shutter of the camera to high speed.

Cover front of the lens with a ND filter according to the prevailing lighting conditions. The brighter the lighting conditions, a higher ND factor is required.

Observe an image of a distant object. (Over 10m is recommended.)

Set the zoom ring at [TELE] position and the focus ring at [FAR] position, and then adjust back focus of the camera.

Make focus adjustments with the focusing ring, confirming that objects are in focus across the entire zoom range, especially at the [TELE] and [WIDE] positions.

■ External view

HS2V TS2V

TS3V

■ Adjustments (For video drive iris lens only)

For DC drive iris lens refer to Operating Instructions of the camera.

ALC adjustment

Metering method of the auto-iris can be linearly adjusted from average metering to peak metering (Pk). It is factory set at (Av) position. In case contrast of images is high or low, make adjustment according to the following table.

Images	ALC adjustment direction
To make contrast lower	Clockwise to (Pk)
To make contrast higher	Counter-clockwise to (Av)

Please Note:

•Adjustment by excessive amount may deteriorate image quality.

•ALC may not function due to backlight compensation and AGC of the camera or cameras with a digital video output.

Level adjustment

Auto-iris sensitivity can be adjusted in accord with the camera. When images are too dark, too bright or there is no image, make the adjustment according to the following table.

Images	LEVEL adjustment direction
To brighten the image (raise level)	Clockwise to (H)
To darken the image (lower level)	Counter-clockwise to (L)

Please Note:

•Adjustment by excessive amount may deteriorate image quality or cause malfunction of the iris.

•Make the adjustment over high contrast objects for the best result.

•LEVEL may not be lowered in some cases due to backlight compensation and AGC features of the camera being switched on.

•When the AGC of the camera is switched on, there are some instances where the level does not alter and the image quality deteriorates, even when the

“LEVEL” adjustment variable resistor is turned all the way to “L” side. Turn the “LEVEL” variable resistor towards “H” until the image quality improves.

■ After-sales servicing

Contact your supplier for after-sales servicing.

■ Composition

Lens body	Front cap	Rear cap
Operating instructions

■ marking

The lenses having CE marking on their bodies are conformity with the standards EN50130-4 and EN55022 related to EMC directives by EU.

■ Main specifications

		TS2V214AE	TS3V310E	HS2V616E
	Model number	TS2V214AED	TS3V310ED
				S2V616ED
		TS2V214AEDW	TS3V310EDW
	Format size	1/3	1/3	1/2
	Mount	CS	CS	CS
	Focal length	2.8mm - 6mm	3mm - 8mm	6mm - 12mm
	Iris range	F1.4 - 300	F1.0 - F360	F1.6 - F300
	Min. object distance	0.3m	0.3m	1m
	Temperature range		-20 - +50

Video drive iris lens			DC drive iris lens
Power supply	DC8V - 15V 40mA or less		Driving coil	200Ω±10 25
Video signal	V or VS		Damping coil	700Ω±10 25
Sensitivity adjustment	0.5V(p-p) - 1.0V(p-p) at V signal level		Driving voltage	+4V or less (Close to Open)
Iris accuracy	±20% at V signal level			Over 0.5V (Open to Close)

2-36-9, Maeno-cho, Itabashi-ku, Tokyo 174-8639, Japan

Phone [phone] Fax. [phone]

3160635-Z2-1 (E) S3095072