Pentax Galaxy 3-48C Installation Manual
Galaxy
3-48C, 3-144, 3-144C, 3-520, 3-520C
Installation Manual
Honeywell Security
Galaxy 3 Series Installation Manual
Table of Contents
i
Content s
Introduction .............................................................................................1-1
Variants................................................................................................................1-1
Section 1: Quick Setup ..........................................................................1-3
Section 2: System Architecture............................................................2-1
PCB Layout..........................................................................................................2-4
RS485 Expansion Module (G3-520 only) .........................................................2-5
System Installation and Wiring.........................................................................2-6
Connecting the Galaxy 3 Series to the PSTN..................................................2 -7
Connecting Additional Telecom Apparatus...................................................................2-8
Line Monitoring .................................................................................................................2-8
Stand-by Battery................................................................................................. 2-9
Battery Start-up .................................................................................................................2-9
On-Board Power Supply Unit.............................................................................2-9
Memory ..............................................................................................................2-10
RS485 Data Communication Bus (AB Lines) .................................................2-10
RS485 Wiring Configurations..........................................................................2-10
RS485 Wiring Recommendations ...................................................................2-11
Zones .................................................................................................................2-13
Zone Addresses..............................................................................................................2-13
Zone Addressing with Onboard RIO Switch...........................................................................................2-14
Wiring Zones ................................................................................................................... 2-14
Wiring Multiple Zones......................................................................................2-15
Wiring Keyswitches ........................................................................................................ 2-15
Wiring Terminator Buttons ............................................................................................ 2-16
Outputs ..............................................................................................................2-16
Output Applications .........................................................................................2-17
SPI Header........................................................................................................................2-18
Section 3: Optional Modules and Facilities..........................................3-1
Remote Input Output (RIO) Modules – C072 ....................................................3-1
Addressing ........................................................................................................................3- 1
Connecting the RIO ...........................................................................................................3-2
Configuring the RIO ..........................................................................................................3-2
Outputs...............................................................................................................................3-3
Galaxy 3 Series Installation Manual
Table of Contents
ii
Entry/Exit RIO.....................................................................................................................3-3
Entry/Exit RIO Zone Programming ...........................................................................................................3-4
Entry/Exit RIO Zone Operation .................................................................................................................3-4
Slave RIO ...................................................................................................................... ...........................3-4
RF RIO – C076 .....................................................................................................3-5
Connecting the RF RIO.....................................................................................................3-5
Addressing the RF RIO.....................................................................................................3-6
Address Ranges ......................................................................................................................................3-6
RF RIO Programming........................................................................................................3-7
Configuring the RF RIO .................................................................................................... 3-7
Output Module – C078 .......................................................................................3-8
Addressing ........................................................................................................................3- 8
Connecting the Output Module .......................................................................................3-9
Configuring the Output Module ......................................................................................3-9
Outputs...............................................................................................................................3-9
Configuration Jumpers..................................................................................................3-10
Relay Module ................................................................................................................... 3-11
Technical Specification - Output Module ..................................................................... 3-11
Technical Specification - Relay Module .......................................................................3-11
Power Supply Unit ............................................................................................3-12
Configuration...................................................................................................................3-12
Installation Instructions ................................................................................................. 3-13
Battery ..............................................................................................................................3-14
Battery Test......................................................................................................................3-14
Specifications..................................................................................................................3-14
EN50131 Compliance ......................................................................................................3-14
Printer Interface Module-A134/A161 ..............................................................3-15
Telecom Module – E062...................................................................................3-16
Connection to the PSTN.................................................................................................3-16
Programming the Telecom Module ..............................................................................3-16
RS232 Interface Module - E054 .......................................................................3-17
Interface with a PC...........................................................................................................3-17
Serial Printer Interface ....................................................................................................3-18
ISDN Module – E077 .........................................................................................3-19
Programming the ISDN Module..................................................................................... 3-19
Ethernet Module - E080....................................................................................3-20
Configuring the Ethernet Module ................................................................................. 3-20
Ethernet Communication............................................................................................... 3-20
Remote Servicing Suite....................................................................................3-21
Event Monitoring .............................................................................................................3-21
Galaxy Gold ......................................................................................................................3-21
User Management Suite.........................................................................................................................3-21
Galaxy 3 Series Installation Manual
Table of Contents
iii
Section 4: The Galaxy Mk7 Keypad/KeyProx.......................................4-1
General.................................................................................................................4-1
Power Consumption .........................................................................................................4-1
Wiring the Keypad/KeyProx .............................................................................................4-2
Addressing ........................................................................................................................4- 2
Keypad/KeyProx Installation Procedure .......................................................... 4-2
Volume Control..................................................................................................................4-4
Adding a Keypad/KeyProx to the System ...................................................................... 4 -4
Removing a Keypad/KeyProx from the System............................................................4-4
Self Diagnostics ................................................................................................................4-5
Keypad/KeyProx Operation.............................................................................................4-5
Number Keys ...........................................................................................................................................4-5
View Keys ................................................................................................................................................4-5
Enter Key ..................................................................................................................................................4-5
Escape Key ..............................................................................................................................................4-6
Hash Key..................................................................................................................................................4-6
Star Key....................................................................................................................................................4-6
Power LED ...............................................................................................................................................4-7
Display......................................................................................................................................................4-7
The Galaxy KeyProx...........................................................................................4-8
General ...............................................................................................................................4-8
Addressing ........................................................................................................................4-8
Operation ............................................................................................................................4-8
Card Types.........................................................................................................................4-8
Section 5: Door Control Module - MAX3...............................................5-1
Introduction.........................................................................................................5-1
Standalone.........................................................................................................................5-1
On-line ................................................................................................................................5-1
Installing the MAX3 ............................................................................................5 -1
MAX3 Pack .........................................................................................................................5-1
Mounting the MAX3 ........................................................................................................... 5-1
Wiring the MAX3 .................................................................................................5- 2
Configuring a MAX3 Reader into the System................................................................5-3
Configuring as On-Line MAX3 .........................................................................................5 -3
Configuring as a Stand-Alone MAX3.............................................................................. 5 -4
Removing a MAX3 Reader from the System..................................................................5-5
On-Line Mode ...........................................................................................................................................5-5
Operating Instructions .....................................................................................................5-5
Card-Held Function............................................................................................................. ......................5-5
Card-Held System Setting........................................................................................................................5-5
MAX3 Log...........................................................................................................................5-6
Downloading the MAX3 Log.....................................................................................................................5-6
Galaxy 3 Series Installation Manual
Table of Contents
iv
Dual Access Cards............................................................................................................5-7
Dual Focus (Card Held) .................................................................................................... 5-7
Timed Anti-Passback ........................................................................................................5-7
Appendix A : Door Control - MAX (MX01)............................................ A-1
Installation Instructions ................................................................................... A-1
Wiring the MAX ................................................................................................................. A-1
Mounting the MAX ............................................................................................................ A-2
Surface Mounting the MAX...................................................................................................................... A-2
Flush Mounting the MAX .........................................................................................................................A-2
Configuring a MAX Reader into the System ................................................................. A-3
Configuring as a Stand-Alone MAX ............................................................................... A-3
Configuring as On-Line MAX.......................................................................................... A-4
Removing a MAX Reader from the System................................................................... A-5
Stand Alone Mode .................................................................................................................................. A-5
On-Line Mode ..........................................................................................................................................A-5
Programming Instructions for On-Line Readers ......................................................... A-5
Operating Instructions (On-Line Modes)...................................................................... A-6
Gaining Access ....................................................................................................................................... A-6
Card-Held Function..................................................................................................................................A-6
Max Log ............................................................................................................................. A-7
Max Events Print-Out............................................................................................................................... A-7
Appendix B: 3 Ampere Smart PSU - P015........................................... B-1
Grounding......................................................................................................................... B-1
Appendix C: Panel Comparisons......................................................... C-1
Appendix D: Declaration of Conformity .............................................. D-1
Compliance and Approvals .............................................................................. D-1
EN50131 Compliance ......................................................................................... D-2
PD6662 Compliance ........................................................................................... D-2
Public Switched Telephone Network (PSTN) approval.................................. D-2
Appendix E: Specifications ...................................................................E-1
Panel Specifications ...........................................................................................E-1
Appendix F: Parts List Index.................................................................F-1
Index............................................................................................................ 1
1-1
Galaxy 3 Series Installation Manual
Introduction
This manual gives full instructions required to install a Galaxy 3 Series control panel and associated
peripherals.
Throughout this Installation Manual, references to menu options, unless otherwise indicated, are found in the
Galaxy 3 Series Programming Manual, part number IP1-0033.
Variants
The Galaxy 3 Series is available in five variants: 3-48C; 3-144; 3-144C; 3-520; 3-520C. The differences
between each variant are shown in the following table:
Introduction
Table 1-1. Galaxy 3 Series Variants
NOTE: The RS485 Expansion module gives two extra lines (lines 3 and 4) on the 3-520 only .
VARIANT
ON-BOARD
COMMS
RS485 EXPANSION
MODULE
RS485 LINES
3-48C YES NO 1
3-144 NO NO 2
3-144C YES NO 2
3-520 NO YES 4
3-520C YES YES 4
1-2
Galaxy 3 Series Installation Manual
Galaxy 3 Series Installation Manual
Quick Setup
Section 1: Quick Setup
T o quickly set up a Galaxy 3 Series control panel for programming follow these simple steps:
1. Connect a 1k Ω (1%) resistor across each of the zones on the panel and any RIO’ s (if connected).
2. Ensure that the tamper return loop — the terminal marked as AUX T AMP on the PCB — is a complete
loop.
NOTE: This is factory set as a completed loop with a 0 V return.
3. Connect one of the keypads to the AB LINE terminals on the control panel. The Galaxy 3-48 has
one AB line; the Galaxy 3-144 has two AB lines; the Galaxy 3-520 has four AB lines (when an
RS485 Expansion Module is fitted).
NOTE: G3-48 - There is one AB LINE terminal on the control panel PCB.
NOTE: G3-144/G3-520 - There are two AB LINE terminals on the control panel PCB.
lenaPlortnoC
)1eniL(
1BB
1AA
--
++
dapyeK
T able 1-2. Terminal Connections
4. Connect a 680 Ω End Of Line (EOL) resistor across the A and B terminals of the keypad.
5. Ensure that the keypad is fitted to the wall (see Keypad Installation Procedure, Section 4).
6. Connect the battery before replacing the control panel lid.
7. Connect the mains wiring to the control panel. Do not switch the mains ON.
8. Replace the control panel lid and secure the fastening screws.
9. Switch on the mains voltage (230 Va.c. / 50 Hz).
10. The following sequence of events occur:
• the keypad buzzer and control panel horn (if fitted) activate for 10 - 20 seconds,
• flashing is displayed on the keypad,
• the sounders stop and the keypad displays become blank,
• the green power LED lights and the following displays on the keypad
ConfiguringConfiguring
Configuring
ConfiguringConfiguring
Please WaitPlease Wait
Please Wait
Please WaitPlease Wait
• the default banner is then displayed on the keypad.
GALAXY <XXX> <VY.YY>GALAXY <XXX> <VY.YY>
GALAXY <XXX> <VY.YY>
GALAXY <XXX> <VY.YY>GALAXY <XXX> <VY.YY>
01:0101:01
01:01
01:0101:01
SUN 01 JAN SUN 01 JAN
SUN 01 JAN
SUN 01 JAN SUN 01 JAN
where: XXX is the panel type
Y .YY is the panel software revision
11. The system is now ready to be programmed. Refer to Galaxy 3 Series Programming Manual:
IP1-0033 for programming details.
1-3
1-4
Galaxy 3 Series Installation Manual
Galaxy 3 Series Installation Manual
2-1
Section 2: System Architecture
G3-48 Configuration
Figure 2-1. Galaxy 3-48 System Configuration
16 zones on board
Galaxy 3-48
Line
1
K
eypads (8)
CP027/
Keyprox (3)
CP028
8 zones
4 outputs
RIO (4)
C072
8 zones
4 outputs
OR
NOTE:
The Telecom, Printer Interface,
RS232, Ethernet and ISDN
modules can only be
connected to line 1.
If a Telecom module is attached,
keypad address E cannot be
connected to line 1(address E is
shown as 18 on the system).
If an RS232 module is attached,
keypad address D cannot be
connected to line 1 (address D is
shown as 17 on the system).
If an Ethernet module is attached,
keypad address B cannot be
connected to line 1 (address B is
shown as 15 on the system).
If an ISDN module is attached,
keypad address C cannot be
connected to line 1 (address C is
shown as 16 on the system).
Cable run 1 km (max)
Certain keypad and
max addresses can
be replaced by a
combined keyprox unit.
*
*
*
NOTE:
Valid addresses for the
keyprox are:
Line 1 (0, 1 & 2).
This sets the address for both
the keypad and card reader
parts of the keyprox.
8 outputs
on board
on board
telecom
area
Max (4)
MX03
OR
OR
NOTE:
RIOs, RF RIO's and
PSU's can be mixed on
the lines. The maximum
number of combined
modules is given in the
table below.
*
PSTN
(comm 1)
Smart PSU (4)
P015
8 zones
4 outputs
RF RIO Module (4)
C076
Power Unit (4) P025
or
Power RIO (4) P026
Printer Interface (1)
A134/A161
Twisted Pair
Screened Cable
W002
ISDN Module (1)
E077 (comm 3)
RS232 Module (1)
E054 (comm 2)
Telecom Module (1)
E062 (comm 5)
Ethernet Module (1)
E080 (comm 4)
Output Module (4) C078
NOTE: Each Output Module can simulate
up to 4 RIO's (outputs only) depending
on DIP switch setting.
Valid addresses for the Output Module are
the same as standard RIO's.
4 - 16 outputs
RS232
Serial Port
(comm 6)
On-board RIOs/ Smart PSUs/EN51 PSU Keypads Keyprox MAX
Galaxy Panel Zones Outputs Poss. Address Zones Outputs Poss. Address Poss. Address Poss.
3-48 (line 1) 16 8 4 2 - 5 32 16 8 0, 1 & 2, B, C, D,
E, F
30, 1 & 24
Galaxy 3 Series Installation Manual
2-2
On-board RIOs/ Smart PSUs/EN51 PSU Keypads Keyprox MAX
Galaxy Panel Zones Outputs Poss. Address Zones Outputs Poss. Address Poss. Address Poss.
144 (line 1)
(line 2)
16 8 8
8
1 - 8
0 - 7
64
64
32
32
8
8
0 - 2, B, C, D, E, F
0 - 6, F
3
4
0-2
0-3
4
4
Figure 2-2. Galaxy 3-144 System Configuration
G3-144 Configuration
16 zones on board
Galaxy 3-144
Line
Line
12
K
eypads (8)
CP027/
Keyprox (3)
CP028
Max (4)
MX03
Keypads (8)
CP027/
Keyprox (4)
CP028
8 zones
4 outputs
RIO (8)
C072
8 zones
4 outputs
OR
8 zones
4 outputs
8 zones
4 outputs
Smart PSU (8)
P015
RIO (8)
C072
NOTE:
The Telecom, Printer Interface,
RS232, Ethernet and ISDN
modules can only be
connected to line 1.
If a Telecom module is attached,
keypad address E cannot be
connected to line 1(address E is
shown as 18 on the system).
If an RS232 module is attached,
keypad address D cannot be
connected to line 1 (address D is
shown as 17 on the system).
If an Ethernet module is attached,
keypad address B cannot be
connected to line 1 (address B is
shown as 15 on the system).
If an ISDN module is attached,
keypad address C cannot be
connected to line 1 (address C is
shown as 16 on the system).
Cable run 1 km (max)
Certain keypad and
max addresses can
be replaced by a
combined keyprox unit.
*
*
*
*
*
NOTE:
Valid addresses for the
keyprox are:
Line 1 (0, 1 & 2).
Line 2 (0, 1, 2, & 3 ).
This sets the address for both
the keypad and card reader
parts of the keyprox.
8 outputs
on board
on board
telecom
area
Max (4)
MX03
OR
OR
OR
RF RIO Module (8)
C076
OR
OR
NOTE:
RIOs, RF RIO's and
PSU's can be mixed on
the lines. The maximum
number of combined
modules is given in the
table below.
*
PSTN
(comm 1)
RS232
Serial Port
(comm 6)
8 zones
4 outputs
Power Unit (8) P025
or
Power RIO (8) P026
Smart PSU (8)
P015
8 zones
4 outputs
RF RIO Module (8)
C076
Power Unit (8) P025
or
Power RIO (8) P026
Printer Interface (1)
A134/A161
Twisted Pair
Screened Cable
W002
ISDN Module (1)
E077 (comm 3)
RS232 Module (1)
E054 (comm 2)
Telecom Module (1)
E062 (comm 5)
Ethernet Module (1)
E080 (comm 4)
Output Module (4) C078
NOTE: Each Output Module can simulate
up to 4 RIO's (outputs only) depending
on DIP switch setting.
Valid addresses for the Output Module are
the same as standard RIO's.
4 - 16 outputs
Output Module (4)
C078
4 - 16 outputs
Galaxy 3 Series Installation Manual
2-3
On-board RIOs/ Smart PSUs/EN51 PSU Keypads Keyprox MAX
Galaxy Panel Zones Outputs Poss. Address Zones Outputs Poss. Address Poss. Address Poss.
520 (line 1)
(lines 2, 3, 4)
16 8 15161 - 9, A - F
0 - 9, A - F
120
384
60
64
8
8
0 - 2, B, C, D, E, F
0 - 6, F
3
7
0-2
0-6
8
8
Figure 2-3. Galaxy 3-520 System Configuration
G3-520 Configuration
Galaxy 3-520
Line Line Line Line
1234
K
eypads (8)
CP027/
Keyprox (3)
CP028
Max (8)
MX03
Keypads (8)
CP027/
Keyprox (7)
CP028
8 zones
4 outputs
RIO (15)
C072
8 zones
4 outputs
OR
8 zones
4 outputs
8 zones
4 outputs
Smart PSU (16)
P015
RIO (16)
C072
Twisted Pair
Screened Cable
W002
Cable run 1 km (max)
Cable run 1 km (max)
Lines 2, 3 and 4 have the same configuration
RF RIO Module (16)
C076
Certain keypad and
max addresses can
be replaced by a
combined keyprox unit.
*
*
*
*
*
NOTE:
Valid addresses for the
keyprox are:
Line 1 (0, 1 & 2).
Lines 2, 3 & 4 (0-6).
This sets the address for both
the keypad and card reader
parts of the keyprox.
16 zones on board
8 outputs
on board
on board
telecom
area
Max (8)
MX03
OR
OR
OR
OR
OR
NOTE:
RIOs, RF RIO's and
PSU's can be mixed on
the lines. The maximum
number of combined
modules is given in the
table below.
*
RS232
Serial Port
PSTN
8 zones
4 outputs
Power Unit (16) P025
or
Power RIO (16) P026
Smart PSU (15)
P015
8 zones
4 outputs
RF RIO Module (15)
C076
Power Unit (15) P025
or
Power RIO (15) P026
Printer Interface (1)
A134/A161
ISDN Module (1)
E077 (comm 3)
RS232 Module (1)
E054 (comm 2)
Telecom Module (1)
E062 (comm 5)
Ethernet Module (1)
E080 (comm 4)
Output Module (4)
C078
4 - 16 outputs
Output Module (4) C078
NOTE: Each Output Module can simulate
up to 4 RIO's (outputs only) depending
on DIP switch setting.
Valid addresses for the Output Module are
the same as standard RIO's.
4 - 16 outputs
NOTE:
The Telecom, Printer Interface,
RS232, Ethernet and ISDN
modules can only be
connected to line 1.
If a Telecom module is attached,
keypad address E cannot be
connected to line 1(address E is
shown as 18 on the system).
If an RS232 module is attached,
keypad address D cannot be
connected to line 1 (address D is
shown as 17 on the system).
If an Ethernet module is attached,
keypad address B cannot be
connected to line 1 (address B is
shown as 15 on the system).
If an ISDN module is attached,
keypad address C cannot be
connected to line 1 (address C is
shown as 16 on the system).
Galaxy 3 Series Installation Manual
2-4
PCB Layout
PCB Layout
Figure 2-4. PCB Layout
LID
TAMP
+12V
+12V
+12V
+12V
1
2
3
4
2
AUX
TAMP
G
N
D
RX
TX
B2
A2
A1
B1
+12V
PHONE
LINE
ABAB
AC
MICRO
PROCESSOR
Telecom
Socket
16 on-board zones
External
loudspeaker
Leads for
lid tamper
microswitch
RS232 Port
Jumper Lead
for off-wall
tamper switch
RS485
line 1
RS485 line 2
(3-144/3-520 only)
Telecom
Connect
Battery
terminals
Expansion card
interface
Horn output
volume control
RIO 0
13
RIO 1
GND
GND
+12V
CTS
RTS
LED1(for Telecoms)
LED2 (for RS232)
LK5
LK3
+12V
4
14.5
+BAT
-BAT
F1
F2
BAT
BELL
F4
AUX1
AUX2 (3-144/3-520 only)
FLASH
SRAM
SPI
Program
Header
OFF WALL
TAMPER
BATTERY
START UP
1
2 3
4 5
6
7 8
SW3
RIO
SWITCH
Engineer socket
(RS485 Line1)
Engineer socket
(RS485 Line 2)
NOTE: Fuse AUX1 controls
RS485 line 1, RIO 0 (zones 1-8)
Fuse AUX2 controls
RS485 line 2, RIO 1 (zones 1-8)
RS232 Port socket
Memory
backup
battery
Pull-up switches
Relay
Output
N/O
C
N/C
ON
ON
NOTE: Zones 1-8 (RIO 0 line 1)
Zones 1-8 (RIO 1 line 1 (switch SW3-8 OFF))
OR
Zones 1-8 (RIO 1 line 0 (switch SW3-8 ON))
1
2
0V
3
4
0V
RIO 0
5
6
0V
7
8
0V
1
2
0V
3
4
0V
RIO 1
5
6
0V
7
8
0V
F3
3-144/3-520 only
Galaxy 3 Series Installation Manual
2-5
The 7 transistorised outputs on the Galaxy 3 Series can be configured to open collectors by setting the dip
switch SW3 to the OFF position.
NOTE: Output 2 on RIO 0 (relay output) is not affected.
The following table shows which outputs are controlled by which switches.
T able 2-1. SW3 T ransistorised Outputs Control
RS485 Expansion Module (G3-520 only)
The RS485 Expansion Module can be attached to the G3-520 to give 2 extra RS485 (AB) lines.
The Expansion module must be wired in a daisy-chain configuration. That is, the A line from the previous
module is connected to the A3 or A4 terminal of the Expansion Module.
The RS485 (AB) line must have a 680 ohm resistor fitted across the A and B terminals of the last module on
the line. If two lines are connected, both ends must be terminated with a 680 ohm resistor and the appropriate
link (LK1 or LK2) removed.
RS485 Expansion Module
Figure 2-5. RS485 Expansion Module
+12V
+12V
+12V
+12V
1
2
3
4
2
AUX
TAMP
G
N
D
RIO 0
13
RIO 1
+12V
4
1
2
0V
3
4
0V
RIO 0
5
6
0V
7
8
0V
1
2
0V
3
4
0V
RIO 1
5
6
0V
7
8
0V
A4
RS485
EXPANSION
MODULE
Jumpers
LK1
LK2
Twin
RS485
lines
A3
B3
B4
(SW3) RIO Output
10 1
20 3
30 4
411
512
613
714
Galaxy 3 Series Installation Manual
2-6
System Installation and Wiring
The installation and wiring must be performed by a competent engineer. For permanently connected equipment, a readily accessible disconnect device must be incorporated in the fixed wiring having contact separation
of at least 3 mm on each pole. The Galaxy 3 Series control panel must be connected to the a.c. mains supply
(230/240 Va.c. 50 Hz) via a fused connection outlet.
The fuse in the mains outlet must not exceed 3A.
WARNING: A means of isolation from the mains supply must be provided within 2 metres of
the control panel. Where live and neutral supplies can be identified, a fused spur
with a 3 amp fuse, must be fitted on the live circuit. Where live and neutral circuits
cannot be reliably identified, 3 amp fuses must be fitted to both circuits.
Route the mains cable through the hole on the right hand side of the enclosure base. Securely anchor the
cable to the box using the tie-wrap as shown in the following Figure:
Figure 2-6. Securing the Mains Cable to the Enclosure Base
Secure the panel base to the wall using three 1.5" No. 8 round head steel screws through the holes provided.
The mains cable used must be a three core type (with green/yellow earth insulation) of adequate current
carrying capacity .
NOTE: The mains cable must satisfy the requirements stated in BS6500.
Connect the mains cable to the mains terminal block as follows:
• blue wire to the terminal marked N (Neutral)
• green/yellow wire to the terminal marked (Earth)
• brown wire to the terminal marked L (Live)
NOTE: No other connections to the mains connector are permitted.
All wiring must be in accordance with the latest edition of the IEE W iring Regulations, BS7671 (Requirements
for Electrical Installations).
Installation Recommendations
Tie wrap
Mains cable
Terminal
block
Earth wire
Mains
transformer
AC connect
Keyhole
slot (top)
PCB
Enclosure
base
Attaching hole
Attaching hole
Galaxy 3 Series Installation Manual
2-7
Connecting the Galaxy 3 Series to the PSTN
The T elecommunications Network V oltage (TNV) port (terminals A and B on PCB) must be permanently
connected (hard-wired) to the PSTN via a BT master socket, refer to Figure 2-7.
Note: If the BT master socket is the newer type (NTE5/CTE5), then the connection can be carried out by the
installation engineer. If the BT master socket is not an NTE5/CTE5, then the network operator must make the
connection.
System Wiring
Figure 2-7. Connecting the Galaxy 3 Series to the PSTN
NOTES: 1. T erminals 2 and 5 on the BT Master Socket must be hard-wired to LINE A and B
terminals on the Galaxy 3 Series PCB. The connection is polarity independent.
2. It is strongly recommended that the Galaxy 3 Series panel is the only device on the line.
3. If another device is to be connected to the line, connect the PHONE terminals on the PCB
to terminals 2 and 5 on a second BT Master Socket.
There are two methods of connecting the on-board T elecom Module to the PSTN:
Method 1
Using cable suitable for connection to 2.8 mm diameter screw terminals, strip back approximately 20 mm of
the outer sheath and then remove approximately 4 mm of the insulation from the wires to be connected to the
Galaxy 3 Series PCB.
Connect terminals 2 and 5 on the BT Master socket across the LINE A and B terminals on the Galaxy 3
Series PCB, see Figure 2-7.
Method 2
Use a standard cable with RJ45 plug on one end and plug into the telecom socket on the Galaxy 3 Series
PCB. Connect the other end of the cable to the BT Master socket as described in Method 1.
PHONE
LINE
ABAB
Incoming
PSTN
Line
2
5
BT Master socket (
NTE5/CTE5
).
BT Secondary socket (
NTE5/CTE5
).
Telecom
Socket
RJ45
Plug
5
2
Galaxy 3 Series Installation Manual
2-8
Connecting Additional Telecom App aratus
A BT secondary socket, allows additional telecom apparatus to be connected in series with the on-board
telecom module. Connect the PHONE terminals A and B on the PCB to the terminals on the BT secondary
socket. See Figure 2-7.
System Wiring (cont’d)
Line Monitoring
Under normal idle state conditions, the on-board T elecom Module monitors the RS485 line. The communication status is indicated by the state of the red LED (LED1) as shown in the following table:
ETATSDELNOITACIDNI
FFODELeludomotylppus.c.doN
s9.0-FFO,s10-NOnoitacinummoclamroN
llacfodnetaeslupelgniSnoitacnummoclamroN
llacmralafodnetagnihsalFnoitacinummoCdeliaF
yxalag,gnirotinommralagnirudnO
SMSdnadlog
noitacinummoClamroN
,gnirotinommralagnirudgnirekcilF
SMSdnadlogyxalag
noitacinummocrooP
langisgnignirhtiwemitnisehsalFgnigniReniL
dellaidsitigidhcaesasesluP
nehwnoitacidnilamroN
llacgnikam
T able 2-2. Comms S tatus
Galaxy 3 Series Installation Manual
2-9
St and-by Battery
The Galaxy 3 Series control panels can accommodate up to 2 x 17 Ahr batteries. Ensure that the battery
connector leads on the control panel Powers Supply Unit (PSU) are connected to the correct terminals on the
battery .
CAUTION: There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
T able 2-3. Battery/Control Panel connections
Battery Start-up
The system can be powered up via the Battery Start-up jumper if there is no AC power . T o do this, short
out the Battery Start-up jumper for the duration of the configuration process only . Never leave the Battery
Start-up connected or else deep discharge of the Stand-by Battery will occur .
On-Board Power Supply Unit
The on-board Power Supply Unit (PSU) supplies and monitors power to the system and peripherals. The
following table shows the fuse name and value in amps.
G3-144/G3-520: The Galaxy 3 Series control panel contains four fuses. Details are given in the table below .
NOTE: The G3-48 does not require fuse AUX2.
T able 2-4. On-board PSU Fuses
Power Monitoring Characteristics: Low battery level: 11.2V
Deep discharge protection: 10.5V
Overvoltage protection: 14.7V
Stand-by Battery
lenaPlortnoCyrettaB
TAB-lanimretev-
TAB+lanimretev+
FUSE NAME VALU E (AMP S ) MONITOR S TYPE
AUX1 1.0 RS485 Line 1, RIO 0, Zones 1-8: +12V,
on-board comms
20 mm, anti-surge
AUX2 1.0 RS485 Line 2, RIO 1, zones 1-8 +12V 20 mm, anti-surge
BATT 1.6 Battery 20 mm, anti-surge
BELL 1.0 Outputs RIO 0 1-4, RIO 1 1-4, Horn output 20 mm, anti-surge
G3-48
The PSU total capacity is 1.5A. Internally the PSU
is split in two in order to ensure sufficient current is
always available for stand-by battery recharge.
The PSU capacity is broken down as follows:
• Battery: 0.75A
• Control PCB: 0.25A
• AUX +12V: 0.5A
G3-144/520
The PSU total capacity is 2.5A. Internally the PSU is
split in two in order to ensure sufficient current is always available for stand-by battery recharge.
The PSU capacity is broken down as follows:
• Battery: 1.25A
• Control PCB: 0.25A
• AUX +12V: 1.00A
The PSU is available for zones/outputs and peripherals.
Galaxy 3 Series Installation Manual
2-10
Figure 2-8. Daisy Chain Configuration
Memory
The Galaxy 3 Series control panel is fitted with a memory chip with its own battery backup on the main PCB.
This allows the panel to retain the system configuration, programming details and the event log for up to a year
when both the mains power and standby battery have been disconnected. The memory backup battery must
be kept in place to retain the memory during a mains failure. Re-apply power, this is known as a warm start.
T o completely erase the system memory and return to the default settings, place a piece of thin card between
the retaining clip and the memory backup battery then remove all power to the PCB for one minute. Re-apply
power and remove the card. This is known as a cold start.
The memory backup battery shoud be replaced every 5 years.
CAUTION: There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
CAUTION: Do not overstress the retaining clip when removing and installing the backup
battery. The clip must maintain a firm pressure on the backup battery at all times.
RS485 Data Communication Bus (AB Lines)
Communication between the Galaxy control panels and the modules attached to the system takes place on the
AB lines. The communication protocol is RS 485 format. The control panel constantly monitors the modules
attached to it. A break in the communication from any of the modules generates a module tamper alarm
RS485 Wiring Configurations
The system must be wired in a daisy-chain configuration. That is the A line from the previous module is
connected to the A terminal of the current module and then on to the A line of the next module.
The RS485 (AB) line must have a 680 Ω resistor fitted across the A and B terminals of the last module on the
line. If two lines are connected, both ends must be terminated with 680 Ω resistors and the appropriate link
(LK3 or LK5) removed.
Each AB line can run in two directions from the control panel.
• Remove link LK3 (RS485 line1) or link LK5 (RS485 line2).
• Run two lines from the A and B terminals of the line.
• Terminate both Ends of Line (EOL) with a 680 ohm resistor .
NOTE: It is permissable to have different configurations on each line. For example, line 1 - Daisy chain;
line 2 - twin AB daisy chain.
Memory
Galaxy
Control
Panel
680 Ω
Fit LK3/LK5 on PCB
A
B
AB
680 Ω EOL
A
B
Keypad/Keyprox
OR
Module
Galaxy 3 Series Installation Manual
2-11
2. The system must be wired in a daisy-chain configuration. Spur and star configurations must not
be used as they reduce the immunity to electrical interference.
3. The cable used to connect the RS485 (AB) line must be screened twisted pair (Part No. W002) or
Belden 8723 equivalent.
4. Shielded twisted pair cable, where used, is connected to the earthing pillar on the Galaxy control
panel using the P-clip and nut supplied (refer to Figure 2-10).
5. The RS485 (AB) line must have a 680 Ω resistor fitted across the A and B terminals of the last
module on the line. If twin lines are connected, both ends must be terminated with 680 Ω resistors and
the appropriate link on the control panel PCB must be removed (refer to figure 2-9).
Figure 2-9. T win AB Line Daisy-Chain configuration
RS485 Wiring Recommendations
T o ensure that the system communicates at the maximum level of efficiency , the following recommendations
must be adhered to:
1. Each communication line can support 32 devices. The maximum number of devices on each line
are:
T able 2-5. Communication Devices
RS485 Recommendations
A
B
A
B
Galaxy
Control
Panel
680 Ω EOL
680 Ω EOL
A
B
Keypad/Keyprox
OR
Module
Keypad/Keyprox
OR
Module
Remove
LK3/LK5
Galaxy 3-48
(Line 1 only)
Galaxy 3-144
(Lines 1-2)
Galaxy 3-520
(Lines 1-4)
Keypads
8 8 per line 8 per line
Keyprox
3
3 (line 1)
4 (line 2)
3 (line 1)
7(lines 2, 3, 4)
RIO's/SPSU's
4 8 per line
15 (line1)
16 (lines 2, 3, 4)
Output Mod ule
4 4 per line 4 per line
RF RIO
4 8 per line
15 (line 1)
16 (lines 2, 3, 4)
MAX
4 4 per line 8 per line
RS232
1 1 (line 1 only) 1 (line 1 only)
Telecoms
1 1 (line 1 only) 1 (line 1 only)
Printer
1 1 (line 1 only) 1 (line 1 only)
ISDN
1 1 (line 1 only) 1 (line 1 only)
Ethernet
1 1 (line 1 only) 1 (line 1 only)
RS485 Recommendations
Galaxy 3 Series Installation Manual
6. There must only be a single AB pair of wires in each of the cables.
7. The minimum voltage level is 10.5 Vd.c. with 12.5 Vd.c. being the recommended working minimum.
8. The power supply in the Galaxy control panel and remote power supplies must not be connected
in parallel.
9. The 0 V of all remote power supplies should be connected in common to the 0 V of the Galaxy
control panel.
10. Ensure that any extension loudspeakers are not wired in the same cable as an AB pair of wires.
11. Where possible, ensure that the AB cable is at least 30 centimetres away from any other cables.
12. Where possible, ensure that the AB cable does not run parallel to other cables for extended
distances (maximum 5 metres).
AB connectors
P-clip
A
data line
RS 485 cable
Nut
P-clip
Earthing pillar
(threaded)
B
data line
Cable screen
Figure 2-10. Connection of cable screen using P-Clip
2-12
Galaxy 3 Series Installation Manual
Zone Addresses
Zones
The default setting for the zones on the Galaxy 3 Series are shown in the following table:
Galaxy
Panel
3-48 Final Exit Intruder
3-144 Final Exit Intruder
3-520 Final Exit Intruder
Zone 1001 Zone 1002
Remaining
Zones
T able 2-6. Default Zone Functions
Zone Addresses
Each zone has a four digit address; 1004, 4136. The address is made up of three reference numbers as shown
in the following figure:
Example: 3057
3
05 7
Represents Panel
Line No.
GALAXY
G3 PANEL
1 2 3 4
Represents
RIO Address
RIO
ADDRESS 05
Represents
Zone No. 1-8 on
RIO
Figure 2-1 1. Zone Addr esses
For example, zone 3057 is the detector connected to line 3, RIO 05, zone 7.
ZONE 7
2-13
Galaxy 3 Series Installation Manual
2-14
T able 2-8. Double Balanced Zone
Resistance and Conditions
T able 2-7. Zone Address Ranges
Wiring Zones
The zones on Galaxy 3 Series panels can be Double Balanced (default) or End of Line. Zones can be programmed with different resistance ranges for zone status activation (see Galaxy 3 Series Programming
Manual, IP1-0033, parameter 51.46 = Parameters.Zone Resistance). Refer to T able 2-8 (Double
Balanced) or T able 2-9 (End of Line) for details of the zone resistance and resulting conditions.
NOTE: The circuit debounce time (the period the zone must remain in a state to register a change in condi-
tion) is 300 milliseconds by default.
Zone Addressing with Onboard RIO Switch
The RIO switch (SW3, dipswitch 8) controls the ordering of the on-board RIO’s. This dipswitch must be set
before powering up the panel.
NOTE: The RIO switch is not functional on the 3-48. It defaults to the Switch off configuration.
Switch off (default)
When the switch is set to this mode, the onboard RIO’s configure to the following addresses:
Onboard RIO0 Zone address range: 1001-1008 Outputs: 1001-1004
Onboard RIO1 Zone address range: 1011-1018 Outputs: 1011-1014
Switch on
When the switch is set to this mode, the onboard RIO’s configure to the following addresses:
Onboard RIO0 Zone address range: 1001-1008 Outputs: 1011-1014
Onboard RIO1 Zone address range: 0011-0018 Outputs: 0011-0014
RIO Switch
T able 2-9. End of Line Zone Resistance
and Conditions
PANEL ON-BOARD RIO RANGE TOTAL RIO's TOTAL
3-48 1001 - 1008, 1011 - 1018 16 Line 1 (4) 48
3-144 1001 - 1008, 1011 - 1018,
0011 - 0018 (switch on)
16 Line 1 (8)
Line 2 (8)
144
3-520 1001 - 1008, 1011 - 1018,
0011 - 0018 (switch on)
16 Line 1 (15)
Line 2 (16)
Line 3 (16)
Line 4 (16)
520
Preset 1 - 1k Preset 2 - 2k2 Preset 3 - 4k7
Tamper S/C 0 - 800 0 - 1800 0 - 3700
Low Res 800 - 900 1800 - 2000 3700 - 4200
Normal 900 - 1200 2000 - 2500 4200 - 5500
High Res 1200 - 1300 2500 - 2700 5500 - 6500
Open 1300 - 12000 2700 - 12000 6500 - 19000
Masked 12000 - 15000 12000 - 15000 19000 - 22000
Tamper O/C 15000 - infinity 150 0 0 - infini ty 220 0 0 - infini ty
Preset 1 - 1k Preset 2 - 2k2 Preset 3 - 4k7
Tamper S/C 0 - 800 0 - 1800 0 - 3700
Low Res 800 - 900 1800 - 2000 3700 - 4200
Normal 900 - 1200 2000 - 2500 4200 - 5500
High Res 1200 - 1300 2500 - 2700 55 00 - 6500
Masked 1300 - 12000 2700 - 12000 650 0 - 19000
Open 12000 - infinity 12000 - infinity 19000 - infinity
Galaxy 3 Series Installation Manual
2-15
Figure 2-12. Preset 1 - Double balanced Zone/Detector wiring
Zone Wiring
NOTE: N/C = Normally Closed
NOTE: The recommended maximum cable run from a zone to a detector is 500 metres.
Wiring Keyswitches
Latching or spring loaded keyswitches can be used to set and unset the Galaxy panels; option 52 = PROGRAM ZONES has provision to accommodate both types of transition.
If the keyswitch latches, the transition from 1 kΩ to 2 kΩ initiates the setting procedure of an unset system,
the transition from 2 kΩ to 1 kΩ instantly unsets a set system. If the system is already set, then the transition
from 1 kΩ to 2 kΩ has no effect. If the system is unset, the transition from 2 kΩ to 1 kΩ has no effect. This
is programmed as a Keyswitch in the PROGRAM ZONES option.
If the keyswitch is spring-loaded (returns to its normal position), the transition from 1 kΩ to 2 kΩ initiates the
setting procedure of an unset system and instantly unsets a set system, the transition from 2 kΩ to 1 kΩ - the
return to the normal position - has no effect. This is programmed as a Keyswitch in the PROGRAM
ZONES option.
Wiring Multiple Zones
Multiple detectors can be wired into a single zone as shown in the following Figure. The maximum number of
detectors that can be connected to a single zone is ten.
Figure 2-14. Zone to Multiple Detector Wiring
Figure 2-13. Preset 1 - End of Line Zone/Detector wiring
Zone
Alarm
N/C
Tamper
N/C
1k
1k
500 m
1%
1%
Anti-mask
N/C
12k
1%
Zone
Alarm
Alarm Alarm Alarm
N/C
N/C
N/C N/C
N/C TAMP
1k
1k
1k
1k
1k
1%
1%
1% 1%
1%
N/C
500 m
(10 max)
Zone
Alarm
N/C
Tamper
N/C
1k 1%
Anti-mask
N/C
12k
1%
500 m
Terminator Zone Wiring
Galaxy 3 Series Installation Manual
Wiring T erminator Buttons
Zones programmed as Push-Set (terminator) buttons can be open going closed (2 kΩ to 1 kΩ) or closed
going open (1 kΩ to 2 kΩ). The first activation of the terminator button initialises its status to the system.
NOTE: The first activation of a terminator may not set the system as this can be the initialisation routine. If
the system continues setting, push the button again. The system will set on the second push. This
initialisation only occurs on the first setting. All subsequent setting routines set on the first push of the
terminator.
The wiring of the terminator and keyswitch zone type is shown in the following figure:
Keyswitch
zone
Push-set
zone
Open - Closed
1k
1%
1k to unset, 2k to set
1k
1%
OR
500m
Closed - Open
1%
1k
Figure 2-15. T erminator and Keyswitch Zone Wiring
Outputs
The Galaxy 3 Series control panel on-board outputs are detailed in the following table:
sserddAtuptuO
tluafeDelbanE0eniL
tluafeD
noitcnuF
epyTgnitaR
1k
1k
1%
1%
etatSlamroN
)pu-llup3k3htiw(
10011001slleBdesirotsisnarTAm004,V21evitisoP
20012001ebortSeloPelgniS
revOegnahC
)OCPS(yaleR
30013001APdesirotsisnarTAm004,V21evitisoP
40014001teseRdesirotsisnarTAm004,V21evitisoP
11011100teSdesirotsisnarTAm004,V21evitisoP
21012100redurtnIdesirotsisnarTAm004,V21evitisoP
31013100mrifnoCdesirotsisnarTAm004,V21evitisoP
41014100teseRdesirotsisnarTAm004,V21evitisoP
A1,V03desigrene-eD
T able 2-10. Outputs
2-16
Galaxy 3 Series Installation Manual
Output Applications
Output Applications
The outputs on the Galaxy panels, with the exception of the SPCO relay output, are transistorised outputs;
negative applied (positive removed) by default. These supply up to 400 mA and can be used to drive the
necessary output devices.
NOTE: The polarity of each output can be changed using option 53 = PROGRAM OUTPUTS
Transistorised Output
+12 V
3k3Ω
0 V
Cut 3k3Ω to give
open collector
A) LED
Output
B) Bell
Output
Output
C) Output used to trigger zone
Output
Output must be
open collector
Typical Applications
LED
1kΩ (typical)
Bell
1%
1kΩ
1%
1kΩ
Figure 2-16. Output Configuration and T ypical Applications
Note: For the appropriate 3k3Ω pull-up resistor refer to DIP switch SW3 (T able 2-1).
+12 V
+ 12 V
zone
The relay output is a single pole change over; this can be used to drive output devices that require a clean set
of contacts, isolated from the output voltage.
Horn
Normally
closed
+12 V
Single Pole
Change - 0ver
relay contacts
0 V
Normally open
Figure 2-17. Single Pole Change–Over Relay Output Configuration and T ypical application
2-17
Loading...