Pentair QT4 User Manual
QuickTouch (QT4) Owner’s Manual
4-Function Hand-Held Wireless Remote Control
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Table of Contents
SECTION I. APPLICATION ................................................................................................................................2
SECTION II. KIT CONTENTS ............................................................................................................................. 2
SECTION III. HAND-HELD REMOTE ................................................................................................................... 2
SECTION IV. CONFIGURING BUTTONS ............................................................................................................. 3
SECTION V. INSTALLATION ............................................................................................................................... 4
SECTION VI. CUSTOMIZING THE COMMUNICATION LINK ............................................................................... 5
SECTION VII. HAND-HELD REMOTE BATTERY REPLACEMENT ....................................................................... 5
TROUBLE-SHOOTING ................................................................................................................... 6
WARRANTY ................................................................................................................................... 7
WARNING
Risk of electrical shock or electrocution. It is required that the main power into the home be
switched off at the main circuit breaker box.
WARNING
Before installing this product, read and follow all warning notices and instructions which are included. Failure to
follow safety warnings and instructions can result in severe injury, death, or property damage.
Call (800) 831-7133 for additional free copies of these instructions.
Important Notice
Attention Installer.
This manual contains important information about the installation, operation and safe use of this
product. This information should be given to the owner/operator of this equipment.
Pentair Pool Products
1620 Hawkins Ave., Sanford, NC 27330 • (919) 774-4151
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 523-2400
Rev. A 7-25-03 1 P/N 520209
SECTION I. APPLICATION
Used in conjunction with the IntelliTouch Pool/Spa Control System.
Provides switching of four remote control circuits from a wireless Hand-held Remote.
It is typically used for activating the spa circulation, and for operating three auxiliary pieces of equipment
(such as lights, jet pump, air blower, waterfall, etc.).
Each of the four functions on the Hand-held Remote has an "ON" and an “OFF” button.
SECTION II. KIT INCLUDES:
1-qty. Hand-held Remote (P/N 520018)
1-qty. Receiver (with 9½ ft. cable)
4-qty. Plastic Anchors (for mounting Receiver to concrete or stucco walls)
4-qty. Mounting screws (for mounting Receiver to a flat surface)
SECTION III. HAND-HELD REMOTE
The Hand-held Remote will control four circuits.
Although the Remote is capable of duplicating any four circuits, it has been preset at the factory to control the
following:
Spa Push-button activates the Spa circuit.
“A” Push-button activates Auxiliary 1 circuit.
“B” Push-button activates Auxiliary 2 circuit.
“C” Push-button activates Auxiliary 3 circuit.
If you would like to control circuits other than Spa, Aux1, Aux2 and Aux3, it is possible to make adjustments
through the Indoor Control Panel or MobileTouch.
USING THE HAND-HELD REMOTE
To activate a circuit, press and hold the appropriate "ON" button for at least a full second. To deactivate, press
and hold the OFF button in the same manner.
IMPORTANT
The Hand-held Remote may be used with wet hands, but should never be submersed in water, as this could damage the
unit. If accidental submersion occurs, dry unit out by removing battery cover and removing battery. Position unit so that
water can drain out. Reassemble when completely dry.
P/N 520209 2 Rev. A 7-25-03
SECTION IV. CONFIGURING BUTTONS
Configuring the Buttons of the 4-Function QuickTouch Wireless
Hand-held Remote to control your desired functions
Getting There
MENU SETUP ADVANCED REMOTES CONFIGURE QT WIRELESS
Hint: Before configuring the wireless remote,
assign names to the AUX circuits and / or
FEATURE circuits.
1
To configure the first
button on your wireless
remote, press the top
button at right. The arrow
indicates which button
your are working on.
Hint: The first button of the
wireless remote is labeled
SPA, so configure this
button for the spa mode,
as shown in the photo.
3
To configure the other
three buttons on your
wireless remote, repeat the
process using the next
three buttons at right.
2
Use the DOWN / UP
buttons to scroll through the
circuit names and find the
function you would like to
assign to the spa-side button
you are working on.
Rev. A 7-25-03 3 P/N 520209
Loading...