Pentair IntelliComm, Variable Speed Pump IntelliFlo User Manual

Variable Speed Pump

(Compatible with IntelliTouch

IntelliFlo

™

and IntelliComm)

®

Installation

Listed

IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS

User's Guide

and

Customer Support

Sanford, North Carolina (8 A.M. to 5 P.M.)

Phone: [phone]

Moorpark, California (8 A.M. to 5 P.M.)

Phone: [phone] (Ext. 6312)

Fax: [phone]

Web sites: visit www.pentairpool.com and www.staritepool.com

© 2005 Pentair Water Pool and Spa, Inc. All rights reserved

This document is subject to change without notice

1620 Hawkins Ave., Sanford, NC 27330 • [phone]
10951 West Los Angeles Ave., Moorpark, CA 93021 • [phone]

Trademarks and disclaimers: IntelliFlo, IntelliTouch and the Pentair Water Pool and Spa logo are trademarks of Pentair
Water Pool and Spa, Inc. Other trademarks and trade names may be used in this document to refer to either the entities
claiming the marks and names or their products. Pentair Water Pool and Spa, Inc. disclaims proprietary interest in marks
and names of others.

P/N 350075 - Rev B - 12/29/2005

Contents

Important Safety Precautions ........................................................................................... ii

Section 1: Introduction ...................................................................................................... 1

IntelliFlo Overview ................................................................................................................ 1

IntelliFlo Features ..................................................................................................... 2

IntelliFlo Motor Assembly ......................................................................................... 2

IntelliFlo Motor Features ........................................................................................... 3

IntelliFlo Drive Assembly and Control Panel............................................................. 4

Operator Control Panel Features .............................................................................. 4

Section 2: Operator Control Panel ................................................................................... 5

IntelliFlo Operator Control Panel........................................................................................... 5

Controls and LEDs ................................................................................................... 5

Navigating the Menu Structure ............................................................................................. 7

Section 3: Operating IntelliFlo .......................................................................................... 9

i

How To Meter a System ....................................................................................................... 9

Manual Mode ........................................................................................................................ 9

IntelliFlo Control Panel Menu ............................................................................................... 11

Menu Structure .................................................................................................................... 12

Pool Data Mode ....................................................................................................... 13

Priming Mode ........................................................................................................... 14

Priming Menu ........................................................................................................ 14

Filter Mode ............................................................................................................... 16

Filter Menu ............................................................................................................ 16

Programming Cycles Per Day .............................................................................. 17

Filter Cycle Settings ............................................................................................. 18

Clean Filter Pressure Example ............................................................................. 19

Alert Status ........................................................................................................... 19

Using Filter mode with Features mode ................................................................. 20

Filter Mode and Flow Control ................................................................................ 21

Flow Control and Filter Mode ................................................................................ 21

Time and Contrast Menu ......................................................................................... 22

Setting System Time............................................................................................. 22

Setting the LCD Backlight Contrast ...................................................................... 22

Features Mode ........................................................................................................ 23

Features 1 & 2 ...................................................................................................... 23

Features 3 -9 ........................................................................................................ 23

M. O. Flo................................................................................................................ 23

Feature Settings ................................................................................................... 24

How to use the Feature 1 or 2 (Flow and Duration) mode .................................... 25

Features 1 – 2 (Flow and Duration) ...................................................................... 26

To run Feature 1 or 2 (Flow and Duration) ............................................................ 26

Features 3 – 9 (Flow, Start/Stop Time) ................................................................. 26

Enabling Features 3 – 9 ........................................................................................ 26

Mo Flo (Modulation Output flow) ........................................................................... 28

IntelliFlo Installation and User’s Guide

ii

Contents (Continued)

External Control with IntelliComm Communication Center ....................................... 29

External Control .....................................................................................................29

Setting up External Control using IntelliComm..........................................................30

Controlling IntelliFlo with IntelliTouch......................................................................... 31

Connecting IntelliFlo to IntelliTouch ...........................................................................33

Backwash Mode .......................................................................................................33

Backwash menu ....................................................................................................33

Running Backwash mode......................................................................................34

Backwash menu screens ......................................................................................34

Vacuum Mode ........................................................................................................... 35

Vacuum menu ........................................................................................................35

Section 4: Maintenance ......................................................................................................37

Pump Strainer Basket Service ............................................................................................. 37

Motor Service ....................................................................................................................... 38

Winterizing ............................................................................................................................ 39

Manual Priming and Initial Start-up After Service .................................................................39

Section 5: Installation and Removal ................................................................................. 41

Installing the IntelliFlo ........................................................................................................... 41

Location ....................................................................................................................41

Piping ........................................................................................................................ 41

Check Valves ...........................................................................................................41

Wiring the IntelliFlo ............................................................................................................... 42

Pump Disassembly ..............................................................................................................43

Pump Reassembly/Seal Replacement .....................................................................44

Shaft Seal Replacement ...........................................................................................44

Drive Assembly Removal and Installation ............................................................................ 45

Illustrated Parts List .............................................................................................................. 46

Replacement Parts ...............................................................................................................46

IntelliFlo Pump Dimensions .................................................................................................. 47

IntelliFlo Flow and Power vs Flow Pump Curve ...................................................................47

IntelliFlo Electrical Specifications ......................................................................................... 47

Section 5: Troubleshooting ............................................................................................... 49

Alerts and Warnings .............................................................................................................49

Suction Blockage .................................................................................................................49

General IntelliFlo Troubleshooting Problems.........................................................................50

General Warnings .................................................................................................................52

Electrical Cost Overview......................................................................................................52

How to make your pool more energy efficient ......................................................................53

Using your IntelliFlo pump ....................................................................................................53

Automatic pool sweeps (booster pump style) ...................................................................... 53

Filter during off-peak times ................................................................................................... 53

Setting filtering time .............................................................................................................. 53

Preventive maintenance .......................................................................................................54

Energy Efficient IntelliFlo pump ............................................................................................ 54

IntelliFlo Installation and User’s Guide

IMPORTANT SAFETY PRECAUTIONS

Important Notice:

Attention Installer: This manual contains important information about the installation, operation and safe use

of this product. This information should be given to the owner and/or operator of this equipment.

WARNING — Before installing this product, read and follow all warning notices and instructions which

are included. Failure to follow safety warnings and instructions can result in severe injury,
death, or property damage. Call [phone] for additional free copies of these
instructions.

WARNING — Entrapment Avoidance Notice:

The suction outlet connected to a swimming pool or spa pump can pull a high vacuum
if it is blocked. Therefore, if only one suction outlet smaller than 18" x 23" is used,
anyone blocking the suction outlet with their body can be trapped and held against the
suction outlet. Disembowelment or drowning can result. Therefore, if small suction
outlets are used with this pump, to prevent this entrapment and possible death, install
at least two suction outlets in the body of water. Separate these suction outlets as
described in the International Residential Code (IRC), the International Business Code
(IBC), the Consumer Products Safety Council (CPSC) Guidelines for Entrapment Hazards:
Making Pools and Spas Safer or ANSI/IAF-7 Standard for Suction Entrapment Avoidance
in Swimming Pools, Wading Pools, Spas, Hot Tubs and Catch Basins. If suction outlets
are not used, additional entrapment avoidance measures as described in the CPSC
Guidelines or ANSI/IAF-7 should be employed.

iii

The covers used on suction outlets should be approved and listed as conforming to the
currently published edition of ANSI/ASME A112.19.8 Standard covering Suction Fittings
for Use in Swimming Pools, Wading Pools, Spas and Hot Tubs. These covers should be
inspected regularly and replaced if cracked, broken or older than the design lifetime
indicated on them by the manufacturer. The maximum possible flow rate of this pump
should be less than or equal to the maximum approved flow rate indicated on the suction
outlet cover by the manufacturer. THE USE OF UNAPPROVED COVERS OR ALLOWING
USE OF THE POOL OR SPA WHEN COVERS ARE CRACKED OR BROKEN CAN
RESULT IN HAIR ENTANGLEMENT WHICH CAN RESULT IN DEATH.

WARNING — Risk of electrical shock or electrocution.

This pool pump must be installed by a licensed or certified electrician or a qualified pool
serviceman in accordance with the National Electrical Code and all applicable local codes
and ordinances. Improper installation will create an electrical hazard which could result in
death or serious injury to pool users, installers, or others due to electrical shock, and may
also cause damage to property.

Always disconnect power to the pool pump at the circuit breaker before servicing the
pump. Failure to do so could result in death or serious injury to serviceman, pool users

or others due to electric shock.

IntelliFlo Installation and User’s Guide

iv

IMPORTANT SAFETY PRECAUTIONS (continued)

WARNING — Water temperature in excess of 100° Fahrenheit may be hazardous to your health. Prolonged

immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal
temperature of the body reaches a level several degrees above normal body temperature of

98.6° F. (37° C.). The symptoms of hyperthermia include: drowsiness, lethargy, dizziness,
fainting, and an increase in the internal temperature of the body.

The effects of hyperthermia include: 1) Unawareness of impending danger. 2) Failure to
perceive heat. 3) Failure to recognize the need to leave the spa. 4) Physical inability to exit
the spa. 5) Fetal damage in pregnant women. 6) Unconsciousness resulting in danger of
drowning.

WARNING — The use of alcohol, drugs, or medication can greatly increase the risk of fatal

hyperthermia in hot tubs and spas.

WARNING — To reduce the risk of injury, do not permit children to use this product unless they are closely

supervised at all times.

WARNING — For units intended for use in other than single-family dwellings, a clearly labeled emergency

switch shall be provided as part of the installation. The switch shall be readily accessible to
the occupants and shall be installed at least 5 feet (1.52 m) away, adjacent to, and within
sight of, the unit.

WARNING — When setting up pool water turnovers or flow rates the operator must consider local codes

governing turnover as well as disinfectant feed ratios.

CAUTION — Install the pump a minimum of five (5) feet from the inside wall of the pool and spa. Canadian

installations require a minimum of three (3) meters from pool water.

CAUTION — A No. 8 AWG or larger conductor must be wired to the motor bonding lug.

CAUTION — This pump is for use with permanently installed pools and may also be used with hot tubs and

spas if so marked. Do not use with storable pools. A permanently installed pool is constructed
in or on the ground or in a building such that it cannot be readily disassembled for storage. A
storable pool is constructed so that it may be readily disassembled for storage and reassembled
to its original integrity and has a maximum dimension of 18 feet (5.49 m) and a maximum wall
height of 42 inches (1.07 m).

CAUTION — For hot tubs and spa pumps, do not install within an outer enclosure or beneath the skirt of a

hot tub or spa unless so marked.

CAUTION — IntelliFlo is capable of generating systems pressures up to 50 psi. Installers must ensure

that all system components are rated to withstand at least 50 psi. Over pressurizing the
system can result in catastrophic component failure or property damage.

General Installation Information

• All work must be performed by a licensed electrician, and must conform to all national, state,

and local codes.

• Install to provide drainage of compartment for electrical components.

IntelliFlo Installation and User’s Guide

Section 1

Introduction

IntelliFlo Overview

The IntelliFlo variable-speed pump control system offers pool and spa filter automation and advanced
features that include energy conservation and programmable scheduled water features for your pool, spa,
cleaner, waterfall, and other applications.

The IntelliFlo pump can adapt to any application up to 130 gallons per minute, you simply program IntelliFlo to
suit the application. IntelliFlo then dials in the perfect operating conditions.

IntelliFlo can reduce energy cost by as much as 90% based on a pool size up to 15,000 gallons, one turn
per day with a 24 hour cycle.

IntelliFlo constantly monitors water flow and electrical current to ensure that the filtration system is operating
at peak efficiency. This can result in maximum energy efficiency savings never before possible – up to 90%
over conventional pumps. The system protects against loss of prime or impedance of flow, under and over
voltage situations, and thermal overload or freezing.

1

With IntelliFlo there’s no need for pump curves and hydraulic calculations to determine the right pump for
the job. Just set the program for your pool size and desired turnover, and IntelliFlo does the rest.

IntelliFlo variable speed pump

IntelliFlo Installation and User’s Guide

2

IntelliFlo Features

• Sizes itself to any pool

• Reduces energy cost by as much as 90%

• Protects against loss of prime or flow blockage

• Prevents thermal overload

• Detects and prevents damage from under and over voltage conditions

• Protects against freezing

• Can communicate with an IntelliTouch or IntelliComm system via a two-wire connection

• Easy to read operator control panel LCD display

• Operator control panel buttons for pump modes

• Built-in strainer pot and volute

• Ultra energy-efficient TEFC Square Flange Motor

• Compatibility with most cleaning systems, filters, and jet action spas

• 16-button LCD control panel

• Drive assembly features permanent magnet synchronous motor

• Heavy-duty, durable construction designed for long life

• Internal 24-hour clock for setting controlled on/off times for filtering and up to ten water features

• UL listed

IntelliFlo Motor Assembly

The IntelliFlo three-phase six-pole motor operates at 3450 RPM (at 92% efficiency) and 400 RPM (at
90%). The motor assembly is continually cooled by an external fan. Dual seals on the motor shaft and at the
fan assembly seal the entire motor from any moisture entering the motor assembly. For added protection, a
slinger located in front of the main shaft seal assists in slinging water away from the shaft opening in the
flange.

IntelliFlo Installation and User’s Guide

Operator control panel cover

Drive assembly and
electronics enclosure

Motor fan cover

Motor assembly

3

IntelliFlo Motor Assembly

IntelliFlo Motor Features

• Permanent Magnet Synchronous Motor (PMSM)

• High efficiency (3450 RPM 92% and 400 RPM 90%)

• Superior speed control

• Operates at lower temperatures due to high efficiency

• Same technology as deployed in hybrid electric vehicles

• Designed to withstand outdoor environment

• Totally Enclosed Fan Cooled

• Three-phase motor

• 56 Square Flange

• Six-Pole

• Low noise

Communication Port for RS-485
(IntelliTouch and IntelliComm)

Motor stand

IntelliFlo Installation and User’s Guide

4

IntelliFlo Drive Assembly and Control Panel

The IntelliFlo drive assembly consists of an operator control panel and the system electronics that drive the
230 VAC single phase (260 VAC~170 VAC) motor. The drive microprocessor controls the motor by
changing the frequency of the current it receives together with changing the voltage to control the rotational
speed.

Operator Control

Panel, buttons and

Liquid Crystal Display

(LCD)

¾” NPT male nipple

Three Wire Harness

Hot (Red), Hot (Red)

Ground (Green / Yellow)

+/- 20% of 230 Volt

IntelliFlo Drive Assembly

Operator Control Panel Features

• Backwash and Rinse — Informs the user when and how to backwash filter media

• Vacuum — Can be preset using duration and flow parameters to save energy

• Filter — Allows pump to run at peak efficiency, saving users up to 90% in energy cost, based on a

pool size up to 15,000 gallons, one turn per day with a 24 hour cycle

• Feature — Ten feature modes can be programmed to control filtration duration, start and stop time,

and frequency for cleaners, water features, spas, and waterfalls

• Manual — Allows the user to override all programming and run the pump using RPM or flow

(GPM) control parameters

IntelliFlo Installation and User’s Guide

Operator Control Panel

Filter

mode

Vacuum

mode

Back

Wash

Manual

mode

Enter

Select

Start
Stop

Reset

Feature

2

Feature

1

Menu

Escape

On

War n.

Alarm

IntelliFlo

®

14

1

2 3

4

5

6

8

9

10

11

15

12

13

7

This section describes the operator control panel controls and LEDs.

IntelliFlo Operator Control Panel

5

Section 2

Controls and LEDs

1

Filter button/LED: Starts Filter mode. The LED is on when Filter mode is active.

2

3

4

5

6

7

8

Vacuum button/LED: Starts Vacuum mode. The LED is on when Vacuum mode is active.

Backwash button/LED: Starts Backwash mode. The LED is on when Backwash mode is active.

Manual button/LED: Starts Manual mode. The LED is on when Manual mode is active.

Select button: Display available menu items or enters edit mode for changing a value on line two of the display.

Escape button: Go to the next level up in the menu structure or stop editing the current setting.

Menu button: Access the menu items if the pump is stopped.

Enter button: Save current menu item setting. Also, press this button to acknowledge alarms and warning alerts.

IntelliFlo Installation and User’s Guide

6

Controls and LEDs (Continued)

9

Arrow buttons:

• Up arrow: Move one level up in the menu tree or increase a digit when editing a setting.

• Down arrow: Move one level down in the menu tree or decrease a digit when editing a setting.

• Left arrow: Move cursor left one digit when editing a setting.

• Right arrow: Move cursor right one digit when editing a setting.

10

Feature 1 button: Starts Feature 1 mode. The LED is lit when mode is active.

11

Feature 2 button: Starts Feature 2 mode. The LED is lit when mode is active.

12

Start/Stop button: Start or Stop the pump. When the LED is lit it indicates that the pump is currently running or
in a mode to start automatically.

13

Reset button: Reset alarm or alert.

LEDs

On: This green LED is on when IntelliFlo is powered on.

14

Warning: This LED is on if a warning condition is present.

Alarm: This LED is on if an alarm condition has occurred.

15

Control Panel LCD Display

LCD Display Lines:

• Line 1 - Mode and time. To set A.M. and P.M. time, refer to “Time and Contrast Menu” on page 22.

• Line 2 - Data

• Line 3 - Name of data in line 2

• Line 4 - Run status

IntelliFlo Installation and User’s Guide

Navigating the Menu Structure

Before navigating the control panel menu structure, first familiarize yourself with the menu buttons. To
change a parameter setting, use the Left and Right arrow buttons to select the digit, then the Up and Down
arrow buttons to edit the digit. The following example shows how to set the GPM and priming time in the
“Priming” menu (see page 14).

Priming Mode Example

7

To set the “Priming” mode settings:

1. Ensure that the green power LED is on and the pump is stopped.

If the pump is running, press the Start/Stop button.

2. Press the Menu button. “Pool Data” is displayed.

Menu

Start
Stop

3. Press the Down arrow to select “Priming”.

4. Press the Select button to access “Max Priming Flow” setting.

5. Set the GPM: Press the Select button to set the gallons per minute

Select

Select

(GPM) value.

6. To change the GPM value, press the Left and Right arrows to select

which digit to modify.

Press the Up and Down arrows to change the selected digit. For setting
values, see “Priming menu options” below.

7. When you are done, press the Enter button to save the changes. To

Enter

cancel any changes.

Press the Escape button to exit edit mode without saving.

Escape

Menu

Select

Select

5X

MENU 12:15

Pool Data

MENU 12:15

Priming

Priming

12:15

55. GPM

Max Priming Flow

Priming

12:15

0055. GPM

Max Priming Flow

Priming

12:15

0055. GPM

Max Priming Flow

Priming

12:15

0065. GPM

Max Priming Flow

Priming

12:15

0065. GPM

Max Priming Flow

Priming

12:15

0060. GPM

Max Priming Flow

8. Set the priming time: Use the Up and Down arrows to select “Max

Priming Time” and “System Priming Time.”

Press the Select to edit the setting.

Select

9. Repeat steps 5, 6, and 7 to edit the setting.

IntelliFlo Installation and User’s Guide

Enter

Escape

12:15Priming

60. GPM

Max Priming Flow

12:15Priming

15. MIN

Max Priming Time

12:15Priming

0. MIN

System Priming Time

MENU 12:15

Priming

8

Blank Page

IntelliFlo Installation and User’s Guide

This section describes how to use the IntelliFlo pump control panel.

FILTER

1:37

43.GPM

FLOW
RUNNING Schedule

MANUAL

12:15

15.W

POWER
STOPPED

MANUAL

12:15

10.RPM

ACTUAL SPEED
STOPPED

MANUAL

12:15

13.GPM

FLOW
STOPPED

MANUAL

12:15

10.RPM

Set SPEED
STOPPED

MANUAL

12:15

580.GPM

Set FLOW
STOPPED

Metering the System

9

Section 3

Operating IntelliFlo

The first step to operating and programming IntelliFlo is to know what is being used in the
pool system. After the devices are selected you can then set valves for the appropriate
features and use the “Manual” mode to measure flow rates for the types or series of
devices that require flow. When an appropriate flow rate or rates are found for a device
or series of devices, you should note that flow rate for programming later.

Note: If the pool system uses a filter, always monitor pressure at the filter when
changing the speed (RPM) or flow (GPM) from IntelliFlo.

Manual Mode

Operating IntelliFlo in manual mode is typically used for service and testing purposes only.

To operate IntelliFlo in manual mode:

1. Ensure that the green power LED is on.

2. Press the Manual button.

3. Use the Up and Down arrow buttons to view the current power, actual speed and flow:

• Power Menu (Watts): Displays current power to the motor shaft in continuous watts

• Actual Speed (RPM): Displays RPM speed when flow and RPM control is used

• Actual Flow (GPM): Displays actual flow when using flow control

• Set Speed (RPM): Set IntelliFlo to run at a continuous speed

• Set Flow (GPM): Set IntelliFlo in flow control to allow the pump to change speed to manage the

flow rate based on system changes

Filter
mode

On

Warn.

Alarm

Feature

IntelliFlo

Vacuum

mode

Select

Feature

1

®

Back

Manual

Wash

mode

Escape

Menu

Enter

Start

Reset

Stop

2

Filter Vacuum

On

Warn.

Alarm

Feature

1

IntelliFlo

Select

Enter

Feature

2

Manual

®

Back

Manual

Wash

Escape

Start

Reset

Stop

Filter Vacuum

Select

Menu

On

Warn.

Alarm

Feature

1

IntelliFlo

Back
Wash

Enter

Start

Feature

Stop

2

®

Escape

®

IntelliFlo

Manual

Menu

On

Warn.

Alarm

Reset

Filter Vacuum

Select

Feature

1

Feature

2

Enter

Back

Manual

Wash

Escape

Start

Reset

Stop

Filter Vacuum

Select

Menu

On

Warn.

Alarm

Feature

1

IntelliFlo

Back
Wash

Enter

Start

Feature

Stop

2

®

Escape

®

IntelliFlo

Manual

Menu

On

Warn.

Alarm

Reset

Filter Vacuum

Select

Feature

1

Feature

Back

Manual

Wash

Escape

Menu

Enter

Start

Reset

Stop

2

Note: No sensors except the flow control will work while in “Manual” mode. Suction Blockage will
not work in this mode.

IntelliFlo Installation and User’s Guide

10

MANUAL

12:15

Set SPEED
STOPPED

MANUAL

12:15

Set SPEED
STOPPED

MANUAL

12:15

Set SPEED
STOPPED

0010.RPM 1010.RPM0010.RPM

Manual Mode (Continued)

To change the Set Flow and Set Speed features:

1. Ensure that the green power LED is on.

2. Press the Manual button (LED is on).

3. Set Flow: Use the Up and Down arrow buttons to select Set Flow, then press the Select button to

edit the setting.

4. To change the setting, press the Left and Right arrows to select which digit to modify, then use the
Up and Down arrows to change the selected digit. The preset flow values can be set to 15 to 130
GPM (default 50 GPM).

5. When you are done, press the Enter button to save the changes. To cancel any changes, press the
Escape button to exit edit mode without saving.

6. Set Speed: Use the Up and Down arrows to select Set Speed, then press the Select button to edit
the setting. The preset speed can be set to 400 to 3450 RPM maximum (default 1000 RPM).

IntelliFlo

Filter Vacuum

Select

Select

On

Warn.

Alarm

Feature

Feature

1

Cursor hi-lights in

Cursor Hi-lights

in Black

Enter

2

black

Back
Wash

Start
Stop

®

Escape

Manual

Reset

Enter

2

digit

Wash

®

Back

Manual

Escape

Menu

Start

Reset

Stop

IntelliFlo

Filter Vacuum

Select

Menu

On

Warn.

Alarm

Feature

Feature

1

Left/Right arrow

Arrow Keys to

buttons to change

change Values

IntelliFlo

Filter Vacuum

Select

On

Warn.

Alarm

Feature

Feature

1

Press the Enter

Hit Enter and

button to save.

Start/Stop

Press Start/Stop

®

Back

Manual

Wash

Escape

Enter

Start

2

Reset

Stop

Enter

Start
Stop

Menu

7. To change the setting, press the Left and Right arrows to select which digit to modify, then use the
Up and Down arrows to change the selected digit.

8. When you are done, press the Enter button to save the changes. To cancel any changes, press the
Escape button to exit edit mode without saving.

IntelliFlo Installation and User’s Guide

Manual Mode (Continued)

9. Press the Start/Stop button (LED is on) to run IntelliFlo in “Manual” mode (LED is on). The pump

will start and control the flow or speed using the last settings made. After the button is pressed, the
display shows “Running.” To stop IntelliFlo, press the Start/Stop button (LED is off). The display
will show “Stopped.”

Note: While IntelliFlo is running in Manual mode, you can view the current power
consumption and what actual speed is being used.

10. Change Flow and Speed settings while the IntelliFlo is running: The Set Flow and Set Speed

settings can be changed on the fly while the pump is running. To change the flow and speed settings,
perform steps 3 through 8.

• When “Set Flow” is used IntelliFlo will prime then ramp to the current flow rate

• It takes the IntelliFlo about 60 seconds to two minutes to find a flow rate after it is primed. This is best
seen in Actual Speed status display

• While changing the Set Flow setting, IntelliFlo will reprime after a value is changed

11

• While changing the Set Speed setting, IntelliFlo will immediately ramp to the current speed

11. To stop the pump, press the Start/Stop button.

IntelliFlo Control Panel Menu

Use the control panel menu to setup and configure IntelliFlo.

To access the menu features:

• Ensure that the pump is stopped. Press the Menu button. Use the Up or Down arrow button to
scroll through the menu items. Use the Select button to select a menu item. Press the Enter button
to save a setting. Press the Escape button to move up a level from a selected menu item.

Menu Structure

The IntelliFlo menu structure is shown on the following page.

IntelliFlo Control Panel with IntelliComm or IntelliTouch

• The IntelliFlo control panel remains active when the IntelliFlo is connected to an IntelliComm. For
more information see page 29.

• The IntelliFlo control panel is disabled when the Intelliflo is communicating with an IntelliTouch.
"DISPLAY NOT ACTIVE!" will be displayed. For more information see page 31.

IntelliFlo Installation and User’s Guide

12

Main Structure

MAIN SCREEN

POOL DATA

(page 13)

PRIMING

(page 14)

FILTER

(page 16)

TIME / CONTR

(page 22)

FEATURES

(page 23)

Press MENU button to access menu items

Address

Water Temp

Pool Volume

Max Priming Flow

Max Priming Time

Sys Priming Time

Clean Filter Pressure

Turnovers per Day

Cycles per Day

Start Cycle 1

Stop Cycle 1

Start Cycle 2

Stop Cycle 2

Start Cycle 3

Stop Cycle 3

Start Cycle 4

Stop Cycle 4

Clock

Contrast Level

Features 1

Features 2

Features 3

Features 4

Features 5

Features 6

Features 7

Features 8

Features 9

M.O Flow

(1 - 16) [Note: 1-8 when connected to IntelliTouch]

(68˚ - 104˚ F)

(1 - 1000 Kgal)

(30 - 160 gpm)

(1 - 15 min.)

(0 - 5 min.)

(1 - 50 min.)

(1 - 8 counts)

(1 - 4 counts)

(hr:mm - AM/PM)

(hr:mm - AM/PM)

(hr:mm - AM/PM)

(hr:mm - AM/PM)

(hr:mm - AM/PM)

(hr:mm - AM/PM)

(hr:mm - AM/PM)

(hr:mm - AM/PM)

(hr:min - AM/PM)

(0 - 9)

Set Flow (15 - 130 gpm)
Set Duration (0:01 - 10:00)

Set Flow (15 - 130 gpm)
Set Duration (0:01 - 10:00)

Disable/Enable

Set Flow (15 - 130 gpm)
Set Start Time (hr:mm AM/PM)
Set Stop Time (hr:mm AM/PM)

Disable/Enable

Set Flow (15 - 130 gpm)

Set Start Time (hr:mm AM/PM)

Set Stop Time (hr:mm AM/PM)

Disable/Enable

Set Flow (15 - 130 gpm)

Set Start Time (hr:mm AM/PM)

Set Stop Time (hr:mm AM/PM)

Disable/Enable
Set Flow (15 - 130 gpm)
Set Start Time (hr:mm AM/PM)
Set Stop Time (hr:mm AM/PM)

Disable/Enable
Set Flow (15 - 130 gpm)
Set Start Time (hr:mm AM/PM)
Set Stop Time (hr:mm AM/PM)

Disable/Enable
Set Flow (15 - 130 gpm)
Set Start Time (hr:mm AM/PM)
Set Stop Time (hr:mm AM/PM)

Disable/Enable
Set Flow (15 - 130 gpm)
Set Start Time (hr:mm AM/PM)
Set Stop Time (hr:mm AM/PM)

Disable/Enable
Set Flow (15 - 130 gpm)
Set Run Time (0:01 - 00:59)
Set Interval Time (0:02 - 4:15)

EXT. CONTROL

(page 29)

BACKWASH

(page 33)

VACUUM

(page 35)

IntelliFlo Installation and User’s Guide

Program 1

Program 2

Program 3

Program 4

Backwash Flow

Backwash Duration

Rinse Time

Vacuum Flow

Vacuum Duration

Disable/Enable

Set Flow (15 130 gpm) / Time Delay Stop (hr:mn) (0:00 - 0:10)

Disable/Enable (15 - 130 gpm)

Set Flow (15 130 gpm) / Time Delay Stop (hr:mn) (0:00 - 0:10)

Disable/Enable

Set Flow (15 130 gpm) / Time Delay Stop (hr:mn) (0:00 - 0:10)

Disable/Enable

Set Flow (15 130 gpm) / Time Delay Stop (hr:mn) (0:00 - 0:10)

(15 - 130 gpm)

(0:01 - 1:00)

(0:01 - 1:00)

(15 - 130 gpm)

(0:01 - 10:00)

Pool Data Mode

MENU

12:15

Pool Data

Pool Data

12:01

Pump Address

1

Pool Data

12:15

Pool Volume

31.kGAL

Pool Data

12:15

Water Temperature

75.F

Use the Pool Data menu to configure IntelliFlo for the pool and spa system. From this menu you can set an
address for the IntelliFlo pump when connected to an IntelliTouch system, set the volume of pool water, in
1000’s of gallons (kgal) and estimated pool water temperature.

To access the Pool Data menu:

1. Ensure that the green power LED is on and the pump is stopped.

2. Press the Menu button.

IntelliFlo

13

®

3. Press the Up and Down arrow buttons to scroll through the menu items. Press the
Select button to access the “Pool Data” menu.

4. To enter the pump volume (pool size): Press the Select button to access “Pool
Volume” setting. To enter the pool volume setting, see step 7.

The “Pool Volume” value is expressed as 1000’s of gallons (Kgal). Enter from 1 to
1000 Kgal for the pool volume. The volume number can be a close estimate, although
the more accurate the better the turns will be done when employing filter mode. Filter
mode uses this value in coordination with the parameters from Filter mode to sustain
turn rates, flows, and times.

5. To set the water temperature: Use the Up and Down arrows to select “Water
Temperature”. To set the water temperature, see step 7.

Enter the current water temperature from 68° F - 104° F (Default 75° F.) The “Water
Temp” is only for the accuracy of the flow sensor. Temperature accuracy is not
critical, just enter an approximate temperature. When the IntelliFlo is connected to an
IntelliTouch system, water and air temperature information is provided by the system
sensors. The flow reading on the IntelliFlo is –0 / +2 GPM. The closer the
temperature to the actual temperature, the more accurate the flow reading on the
IntelliFlo control panel LCD will be while it’s running.

6. To enter the pump address: Press the Select button to access the “Pump Address”
setting. To enter the IntelliFlo pump address, see step 7.

This setting is only used if IntelliFlo is connected to the IntelliTouch system. The
“Pump Address” identifies the pump number (1-16) that is displayed on the
IntelliTouch control panel for programming. For example, if there are multiple IntelliFlo
pumps, pump address 1 can be name as “Spa Pump,” in the IntelliTouch control panel.
The IntelliTouch system can address and control up to eight different pumps using the
RS-485 COM port connection. Note: IntelliFlo pumps cannot be connected in

series with other pumps. Check valves must be used when an IntelliFlo is used in
parallel with other pumps.

7. Press the Select button to change the current setting.

8. To enter a new setting, press the Left and Right arrows to select which digit to modify,
then use the Up and Down arrows to change the selected digit.

Filter Vacuum

Select

Enter

On

Warn.

Alarm

Feature

Feature

2

1

IntelliFlo

Pool Data

Pump Address

Filter Vacuum

Select

Enter

On

Warn.

Alarm

Feature

Feature

2

1

IntelliFlo

Pool Data

31.kGAL

Pool Volume

Filter Vacuum

Select

Enter

On

Warn.

Alarm

Feature

Feature

2

1

IntelliFlo

Pool Data

75.F

Water Temperature

Filter Vacuum

Select

Enter

On

Warn.

Alarm

Feature

Feature

2

1

Back

Manual

Wash

Escape

Menu

Start

Reset

Stop

®

12:01

Back

Manual

Wash

Escape

Menu

Start

Reset

Stop

®

12:15

Back

Manual

Wash

Escape

Menu

Start

Reset

Stop

®

12:15

Back

Manual

Wash

Escape

Menu

Start

Reset

Stop

9. When you are done, press the Enter button to save the changes. To cancel any
changes, press the Escape button to exit edit mode without saving.

IntelliFlo Installation and User’s Guide

14

MENU

12:37

Priming

Priming

12:44

Max Priming Flow

55.GPM

Priming Mode

To “prime” a pump means filling the pump and suction pipe with water. This process evacuates the air from all
the suction lines and the pump. It may take several minutes to prime depending on the depth of water, pipe size
and length. It is easier to prime a pump if you allow all the air to escape from the pump and pipes. The water
cannot enter unless the air can escape. Pumps do not hold prime, the pool piping system has that task.

Priming is a function used every time the motor is started with a flow as reference. The “Priming Flow” function
ensures the proper operation of the pump. The “System Priming Time” function ensures proper operation of the
whole pool system. When the pump is priming, the control panel LCD displays “Priming” and then for a moment
displays “Primed” when priming is complete.

CAUTION: To avoid permanent damage to the IntelliFlo pump, before starting the system, fill the IntelliFlo

housing strainer with water so that the pump will prime correctly. If there is no water in the stainer the pump will
not prime.

Priming Menu

To enter maximum priming flow (GPM):

1. Ensure that the green power LED is on and the pump is stopped.

2. Press the Menu button. “Pool Data” is displayed.

3. Press the Up or Down arrows to select the “Priming” menu.

4. To set the Max Priming Flow (GPM): Press the Select button to access the “Max

5. To set the Max Priming Time: Press the Select button to access the “Max

IntelliFlo

Priming Flow” setting. To enter the maximum flow range (GPM) during the

Filter Vacuum

priming cycle, see step 7.

On

Warn.

Alarm

Feature

Select

Enter

Feature

2

1

The “Max Priming Flow” value is entered as gallons per minute (GPM), from 30
to 160 GPM. The default is 55 GPM. The “Max Priming Flow” is a critical
parameter for the pool and equipment. Every time the pump starts this parameter
will negotiate the maximum flow of the pump. If the flow is too high, equipment
damage can occur. If the flow is to low the pump will not prime. This “flow” is
system dependent and may require iteration. The pump will never flow more than
this parameter is set to, however, it is common for the pump to ramp up and down
quickly while priming. Always try to keep this flow as low as possible for cost
savings and safety.

Priming Time” setting. To enter the maximum time for priming before “PRIMING

IntelliFlo

Priming

55.GPM

Max Priming Flow

ERROR”, see step 7 on the following page.
The “Max Priming Time” value is entered in minutes, from 1 to 15 minutes. The

Filter Vacuum

default is 15 minutes. Use this parameter to set the time that you want IntelliTouch

On

Warn.

Alarm

Feature

Select

Enter

Feature

2

1

to try and prime before it reports an error. Remember that the IntelliFlo will attain
prime every time it starts and goes through this cycle. The IntelliFlo mechanical
seal can withstand about 15 minutes before severe damage occurs. You can set
this range between 1 minute to 15 minutes. The lower the time the quicker you will
get a priming error if the system is difficult to prime. A well plumbed pool without
having the strainer removed should prime in less than 30 seconds. If the strainer
has been removed for cleaning and a substantial amount of air is in the system it should prime in
about 60 to 90 seconds on the average, however, all systems will be different.

Wash

®

Back

Manual

Escape

Menu

Start

Reset

Stop

®

12:44

Back

Manual

Wash

Escape

Menu

Start

Reset

Stop

IntelliFlo Installation and User’s Guide