Pentair FLECK 5800, FLECK 5810, FLECK 5812 Service Manual

Download

Page 1

FLECK 5800/5810/5812 XTRI (CONNECTED XTR2)

SERVICE MANUAL

pentair.com

Page 2

TABLE OF CONTENTS

OPERATING PARAMETERS ............................................................ 2

JOB SPECIFICATION SHEET .......................................................... 2

INSTALLATION ............................................................................... 3

START-UP INSTRUCTIONS/FLUSHING & CONDITIONING ...........5

SYSTEM DISINFECTION ................................................................. 5

TOUCHSCREEN CONTROL FEATURES.......................................... 6

TOUCHSCREEN SETUP ................................................................. 7

MASTER SETTINGS PROGRAMMING ............................................ 9

ADDITIONAL FEATURES ................................................................ 13

REGENERATION ............................................................................. 14

CONTROL OPERATION ................................................................... 14

MASTER RESET ............................................................................. 14

DIAGNOSTICS ................................................................................ 15

ALARMS AND ERRORS .................................................................. 15

USB CONNECTION FOR FIELD PROGRAMMING ..........................16

TROUBLESHOOTING ......................................................................17

PENTAIR PRO: APP SETUP ...........................................................18

MASTER SETTINGS REFERENCE CHART ..................................... 23

5800/5810/5812 CONTROL VALVE -PART NUMBERS ...................24

POWERHEAD ASSEMBLY............................................................... 25

5800 CONTROL VALVE ASSEMBLY ................................................26

5810 CONTROL VALVE ASSEMBLY ................................................27

5812 CONTROL VALVE ASSEMBLY ................................................28

5800/5810/5812 CONTROL VALVE ACCESSORIES ......................... 29

5800/5810/5812 CONTROL VALVE ASSEMBLIES ..........................30

5800 TURBINE METER ASSEMBLY ................................................ 31

5800 PADDLE METER ASSEMBLY .................................................31

5800 BYPASS VALVE ASSEMBLY (METAL) ..................................... 32

5800 BYPASS VALVE ASSEMBLY (PLASTIC) ..................................32

SAFETY BRINE VALVE .................................................................... 33

WATER CONDITIONER FLOW DIAGRAMS .....................................34

5800 DIMENSIONAL DRAWINGS ................................................... 40

5810 DIMENSIONAL DRAWINGS ................................................... 41

5812 DIMENSIONAL DRAWINGS ................................................... 42

WIRING DIAGRAM .......................................................................... 43

INJECTOR FLOW DATA .................................................................. 44

5800 PERFORMANCE DATA ..........................................................45

5810 PERFORMANCE DATA ..........................................................46

5812 PERFORMANCE DATA ..........................................................47

IMPORTANT PLEASE READ:

• The information, specications and illustrations in this manual are based

on the latest information available at the time of release. The manufacturer reserves the right to make changes at any time without notice.

• This manual is intended as a guide for service of the valve only. System

installation requires information from a number of suppliers not known at the time of manufacture. This product should be installed by a plumbing professional.

• This unit is designed to be installed on potable water systems only.

• This product must be installed in compliance with all state and municipal

plumbing and electrical codes. Permits may be required at the time of installation.

• It is established that when daytime water pressure exceeds 80 psi (5.5

bar), the maximum pressure rating of 125 psi (8.6 bar) can be exceeded. A

pressure regulator must be installed on this system or warranty is voided.

• Do not install the unit where temperatures may drop below 32°F (0°C) or

above 120°F (52°C).

• Do not place the unit in direct sunlight. Black units will absorb radiant heat,

increasing internal temperatures.

• Do not strike the valve or any of the components.

2 • FLECK 5800/5810/5812 XTRI Service Manual

• Warranty of this product extends to manufacturing defects. Misapplication

of this product may result in failure to properly condition water, damage to product, or personal injury.

• A prelter should be used on installations in which free solids are present.

• In some applications local municipalities treat water with Chloramines. High

Chloramine levels may damage valve components.

• Correct and constant voltage must be supplied to the controller to maintain

proper function.

• The system is intended to treat potable water only. The system is not

intended to be used for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before and after the system.

• This system is not intended for use by persons (including children) with

reduced physical, sensory, or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children shall not play with the system.

• Cleaning shall not be made by children without supervision.

• Periodic cleaning and maintenance may be required to function properly.

See disinfection instructions on page 5.

OPERATING PARAMETERS

Minimum Pressure 20 psi/1.4 bar/138 kPa Maximum Pressure 125 psi/8.61 bar/861 kPa Minimum Water Temperature 34°F/1°C Maximum Water Temperature 110°F/43°C Minimum Ambient Temperature 34°F/1°C Maximum Ambient Temperature 120°F/52°C Maximum Humidity 75% Input Voltage 100-240 VAC Input Frequency 50/60 Hz Output Voltage 12 VDC Output Current 2.0 amps Maximum Altitude 2,000 meters

JOB SPECIFICATION SHEET

Job Number: ___________________________________________________

Model Number: _________________________________________________

Water Hardness: _______________________________________ ppm or gpg

Capacity Per Unit: _______________________________________________

Mineral Tank Size: ______________ Diameter: ________ Height: _________

Salt Setting per Regeneration: _____________________________________

Regenerant Flow: Downow Upow Backwash Downow 2x Backwash Filter Upow Variable Rell Custom Downow Custom Upow

1. Meter Size:

A. 3/4" Paddle Wheel Turbine

B. 1" Paddle Wheel Turbine

C. 1-1/2" Paddle Wheel Turbine

D. 2" Paddle Wheel

E. 3" Paddle Wheel

F. Generic_________Pulse Count__________Meter Size__________

2. System Type:

A. System #4: 1 Tank, 1 Meter, Immediate, or Delayed Regeneration

B. System #4: Time Clock

3. Cycle Settings:

A. Backwash: ____________________________________ Minutes

B. Brine and Slow Rinse: ___________________________ Minutes

C. Rapid Rinse: ___________________________________ Minutes

D. Brine Tank Refill: _______________________________ Minutes

E. Pause Time: ___________________________________ Minutes

F. Second Backwash: ______________________________ Minutes

4. Drain Line Flow Control:_____________________________ gpm

5. Brine Line Flow Control: ____________________________ gpm

6. Injector Size#: ________________________________________

7. Battery Install/Change Date: ______________________________

Page 3

CAUTION

INSTALLATION

CAUTION

WARNING:

Water Pressure

A minimum of 20 psi (1.4 bar) of water pressure is required for the regeneration valve to operate effectively.

Electrical Facilities

An uninterrupted power supply is required. The control uses a transformer to supply 12 VDC. Please make sure your voltage supply is compatible with your unit before installation.

Existing Plumbing

Condition of existing plumbing should be free from lime and iron buildup. Piping that is built up heavily with lime and/or iron should be replaced. If piping is clogged with iron, a separate iron filter unit should be installed ahead of the system.

Location of System and Drain

You must have an air gap on the drain line to prevent back flow of drain water into the system. A 2x the drain line pipe diameter air gap (Figure 1) is required with a minimum 1" air gap.

Air Gap

Drain

Figure 1

Installation Locations

FOR DRY LOCATIONS ONLY.

Bypass Valves

Always provide for the installation of a bypass valve if unit is not equipped with one.

Water pressure is not to exceed 125 psi (8.6 bar),

water temperature is not to exceed 110°F (43°C), and the unit cannot be subjected to freezing conditions.

The system must be depressurized before

removing any connections for servicing.

6. Soldering of joints near the drain port must be done prior to connecting the Drain Line Flow Control fitting (DLFC). Leave at least 6" (15 cm) between the DLFC and solder joints when soldering pipes that are connected on the DLFC. Failure to do this could cause interior damage to the DLFC.

7. Plumber tape is the only sealant to be used on the drain fitting.

8. Make sure that the floor is clean beneath the salt storage tank and that the tank is level.

9. Place approximately 1" (25 mm) of water above the grid plate. If a grid is not utilized, fill to the top of the air check (Figure 2) in the salt tank. Do not add salt to the brine tank at this time.

If grid plate is used, cut air check height just below

the grid plate. This is critical on 6", 7", 8" and 9" tanks. The brine refill water must come above the grid plate and make contact with the salt.

10. On units with a bypass, place in bypass position. Turn on the main water supply. Open a cold soft water tap nearby and let run a few minutes or until the plumbing is free from foreign material (usually solder) that may have resulted from the installation. Once clean, close the water tap.

11. Slowly place the bypass in service position and let water flow into the mineral tank. When water flow stops, slowly open a cold water tap nearby and let water run until the air is purged from the plumbing lines.

12. Plug the transformer into an electrical outlet.

NOTE: All electrical connections must be connected according

to local codes. Be certain the outlet is uninterrupted.

Installation Instructions

1. Place the media tank where you want to install the unit. Make sure the unit is level and on a firm base.

2. During cold weather, the installer should warm the valve to room temperature before operating.

3. All plumbing should be done in accordance with local plumbing codes. The pipe size for a residential drain line should be a minimum of 1/2" (13 mm). Backwash flow rates in excess of 7 gpm (26.5 Lpm) or drain line length in excess of 20' (6 m) require 3/4" (19 mm) drain line. Commercial drain lines should be the same size as the drain line flow control.

NOTE: The tank should have the distributor tube installed

and have the proper amount of regenerant in place.

4. Refer to the valve spec sheet for cutting height of the distributor tube.

5. Lubricate the distributor O-ring seal and tank O-ring seal. Place the main control valve on tank. Note: Only use silicone lubricant.

60002 Rev E

Figure 2 Residential Air Check Valve

Electrical Connection

The controller operates on 12-volt DC power supply. Do not operate the controller with a power supply other than the one supplied by the manufacturer for this model. For installation location assistance, see Transformer Port Location on page 4. When installing IOT, a WiFi connection is important. See IOT BOARD POSITIONING OPTIONS on page 4. These positions will provide maximum connection locations.

NOTE: The power source should be constant. Be certain the power adapter is not on a switched outlet. Power interruptions longer than eight hours may cause the controller to lose the time setting. When power is restored, the time setting must then be re-entered.

FLECK 5800/5810/5812 XTRI Service Manual • 3

Page 4

INSTALLATION continued

Outside

Bath TubLavatoryToilet Kitchen

Typical Residential System Plumbing

Faucet

- Side Mount -

Pump

Meter

Hot Water

Outlet

Water Heater

Grounding

Strap

Bypass

Drain Line

Laundry Tubs

Softener

Figure 3 Softened Water Flow

TRANSFORMER PORT LOCATIONIOT BOARD POSITIONING OPTIONS

Soft Water

Faucet

Hard Water

Brine Tank Overow Drain (Optional)

Floor Drain

Air Gap

- Top Mount -

4 • FLECK 5800/5810/5812 XTR I Service Manual

Page 5

START-UP INSTRUCTIONS/

SYSTEM DISINFECTION

FLUSHING & CONDITIONING

The water softener should be installed with the inlet, outlet, and drain connections made in accordance with the manufacturer’s recommendations, and to meet applicable plumbing codes.

1. Program the valve control according to instructions shown in this manual.

2. Start an immediate regeneration by holding the Extra Cycle button for five seconds. Position the valve to backwash. Ensure the drain line flow remains steady for 10 minutes or until the water runs clear.

3. Position the valve to the brine draw/slow rinse position. Ensure the unit is drawing water from the brine tank (this step may need to be repeated).

4. Position the valve to the rapid rinse position. Check the drain line flow, and run for five minutes or until the water runs clear.

5. Position the valve to the start of the brine tank fill cycle. Ensure water goes into the brine tank at the desired rate. The brine valve drive cam will hold the valve in this position to fill the brine tank for the first regeneration.

6. Replace control cover.

7. Put salt in the brine tank.

NOTE: Do not use granulated or rock salt.

Disinfection of Water Softeners

The materials of construction of the modern water softener will not support bacterial growth, nor will these materials contaminate a water supply. During normal use, a softener may become fouled with organic matter, or in some cases with bacteria from the water supply. This may result in an off-taste or odor in the water.

Some softeners may need to be disinfected after installation and some softeners will require periodic disinfection during their normal life.

Depending upon the conditions of use, the style of softener, the type of ion exchanger, and the disinfectant available, a choice can be made among the following methods.

Sodium or Calcium Hypochlorite

Application

These materials are satisfactory for use with polystyrene resins, synthetic gel zeolite, greensand and bentonites.

5.25% Sodium Hypochlorite

These solutions are available under brand names of household bleach. If stronger solutions are used, such as those sold for commercial laundries, adjust the dosage accordingly.

1. Dosage A. Polystyrene resin; 1.2 fluid ounce (35.5 ml) per cubic

foot.

B. Non-resinous exchangers; 0.8 fluid ounce (23.7 ml) per

cubic foot.

2. Salt tank softeners A. Backwash the softener and add the required amount

of hypochlorite solution to the well of the salt tank. The salt tank should have water in it to permit the solution to be carried into the softener.

B. Proceed with the normal recharge.

Calcium Hypochlorite

Calcium hypochlorite, 70% available chlorine, is available in several forms including tablets and granules. These solid materials may be used directly without dissolving before use.

1. Dosage A. Two grains (approximately 0.1 ounce [3 ml]) per cubic

foot.

2. Salt tank softeners A. Backwash the softener and add the required amount of

hypochlorite to the well of the salt tank. The salt tank should have water in it to permit the chlorine solution to be carried into the softener.

B. Proceed with the normal recharge.

FLECK 5800/5810/5812 XTR I Service Manual • 5

Page 6

TOUCHSCREEN CONTROL FEATURES

Features of the XTRI Touchscreen Control

• Full-featured easy to use graphical touchscreen interface for programming, servicing, and diagnostics.

• Non-linear programming no longer requires cycling through every parameter when programming/servicing.

Buttons and Symbols

NOTE: Not all buttons appear on all screens.

Regeneration Cycle Wheel

• Displays the regeneration cycle step the system is currently in. The wheel rotates with each step so that the current step is shown in green.

On metered units, the "Treatment" step on the Regeneration

NOTE:

Cycle Wheel will flash when water is flowing through the unit.

Assistance:

for unit service.

USB Connect:

via a USB cable for field programming or download of diagnostic parameters via PC (Field Programmer application required).

Displays a name and phone number to call

Allows you to connect the control to a PC

Screen Navigation Arrows: Displayed in the

upper-left and upper-right corners of the screen, these arrows allow you to navigate from one screen to another.

NOTE: Settings on previous screen are not saved unless

is pressed.

Settings Arrows: These arrows allow you to change

the values of certain settings when programming the control.

Alarm: Displayed when an alarm has been triggered;

accompanied by an audible alarm. Press to silence the audible alarm.

Home: Displays the Home screen.

Regeneration: Displays the Regeneration screen, which

allows you to start a regeneration and manually cycle through the regeneration steps.

Settings: Displays the Settings screen, which allows

you to adjust commonly used settings. Pressing this button while in the Settings screen provides access to the Master Settings screen, which allows you to fully program the valve.

NOTE:

Due to the complexity of these settings and the

potential for errors, Master Settings should only be accessed by your local water professional.

Diagnostics: Displays the Diagnostic screen, which can

assist in performing maintenance and troubleshooting performance issues with the valve.

Brightness/Sound: Displays the Brightness/Sound

screen, which allows you to adjust the backlight of the control screen and allows you to mute the alarms of the control.

Error: Displayed when an error has occurred. Press

to display the Error screen for more detailed error information.

Advance: This arrow allows you to advance through

cycle steps during a regeneration.

Reset: Displayed in the Diagnostics screen to reset

Totalizer and Peak Flow data and in Master Settings to reset parameters to factory or non-factory settings.

Accept: Press to save or accept changes in

control configuration.

Cancel: Press to cancel configuration and exit to

previous screen without saving.

Alert: Will display when there is no internet

connection.

Vacation Mode: Halts all scheduled regenerations

when pressed; press again to resume normal operation. When Vacation Mode is on, the 100 day regeneration error will be suspended.

6 • FLECK 5800/5810/5812 XTRI Service Manual

WIFI: Represents signal strength to WiFi router.

Bluetooth: When displayed in black, bluetooth signal

is open. When displayed in white, bluetooth connection is engaged.

Page 7

TOUCHSCREEN SETUP

The XTRI control was designed to be easy to set up and begin using right out of the box. The following simple procedure can be used to set up the system and begin treating water in most typical applications.

NOTE: Steps 2 and 3 are optional and are not required to start

NOTE: Press

1. After plugging in the unit, the Format screen (Figure 4) is

the system. All control settings may be changed after the unit is in service.

on any Quick Start screen to reset the screen

back to its default settings.

displayed.

Using the keypad, type the name of the water treatment professional or company that the homeowner may call for system service (optional).

To enter a letter using the keypad, quickly press the keypad button the number of times that correspond with the position of the correct letter on the button. For example, to enter the letter "C", quickly press the ABC button three times. Press

3. After pressing (Figure 6) is displayed.

when finished.

, the Assistance/Mainten. Phone screen

Figure 4 Format Screen

Press the language button to adjust the system's displayed language (international version only): English, French, German, Italian, Spanish, or Dutch. Press

Press the units button to adjust the system's units of measure (either U.S. or metric). Press

Press the hardness units button to adjust the system's hardness units of measure (grains per gallon, mg/L or ppm, German degrees, French degrees, or English degrees). Press if metric units are selected.

NOTE: If the screen is blank after plugging in the unit, touch

2. After pressing (Figure 5) is displayed.

when finished. Hardness units are adjustable only

the screen to turn the screen on.

, the Assistance/Mainten. Name screen

Figure 5 Assistance/Mainten. Name Screen

when finished.

Figure 6 Assistance/Mainten. Phone Screen

Enter the phone number of the water treatment professional or company that the homeowner may call for system service (optional). Press

4. After pressing (Figure 7) is displayed.

Figure 7 Assistance/Mainten. Interval Screen

Use the Assistance/Mainten. Interval screen to set the interval in which the homeowner will need to call a water treatment professional for system service (optional). The assistance interval can be based on a set number of months (month based) or a number of regenerations (regen based).

Press the interval button to select a month-based or regenbased assistance interval, then press the month or regen button (depending on your previous selection), and select the number of months (up to 60) or regenerations (up to 2000) until the homeowner will need to call for service. Press

, the Assistance/Mainten. Interval screen

when finished.

. Press either

FLECK 5800/5810/5812 XTRI Service Manual • 7

Page 8

TOUCHSCREEN SETUP (continued)

5. After pressing , the Home screen (Figure 8) appears.

Next Scheduled

Day and Time

Regeneration Cycle Wheel

Regeneration

Current Cycle

Step

Settings

The Settings screen allows you to change basic control settings including time of regeneration and water hardness. These settings improve the operational efficiency of the system and can be adjusted independently from other control settings without needing to enter Master Settings.

From the Home screen, press the Settings button Settings screen is displayed.

. The

Vacation

Assistance

Figure 8 Home Screen

The Day and Time button will be flashing, indicating that the day of the week and time need to be set. If the date and time are incorrect, press the Day and Time button to update to the correct day and time. The Day and Time screen (Figure

9) appears.

Day

Month

Hour

Minute

Figure 9 Day and Time Screen

Press the Day of Week, Hour, Minute, and AM/PM/HR buttons to adjust the values to the correct day of week and time. Setting the value of the AM/PM/HR button to HR changes the display to a 24 hour clock. Press the Day, Month, and Year buttons to adjust the values to the correct date. Press the Home screen. Press without saving.

button when finished to return to the

Diagnostics

to return to the Home screen

Regeneration

Settings

Year

Day of Week

AM/PM/HR

Brightness/Sound

Figure 10 Settings Screen

• Bluetooth button should be turned on to open bluetooth signal during programming will automatically turn to off when WiFi connected.

• Press day override to adjust the number of days since last regeneration in which a new regeneration will automatically be run whether one is scheduled or not.

• Press regen time to adjust the time of day that an automatic regeneration cycle will begin.

• Press hardness to adjust the hardness setting. This value should match the hardness of the incoming untreated water supply.

NOTE: Changing the hardness setting recalculates treatment

Additional features may be accessed from the Settings screen by pressing the buttons at the bottom of the screen. (see Figure 14):

volume and regeneration interval. This setting should only be changed on the advice of a professional.

• Press the Home screen.

to save your changes or press to return to

Master Settings

8 • FLECK 5800/5810/5812 XTRI Service Manual

Page 9

• Master Settings: Displays the Master Settings screen,

CAUTION

which allows you to fully program the valve.

• Brightness/Sound: Displays the Brightness/Sound screen, which allows you to adjust the backlight of the control screen and allows you to mute the alarms of the control.

NOTE: Due to the complexity of these settings and the

NOTE: Settings can not be accessed during a regeneration.

potential for errors, Master Settings should only be accessed by your local water professional.

If a regeneration starts while in the settings menu, the screen will return to the main screen and all parameters will be voided.

Master Settings

The Master Settings screens include all configurable parameters available in the control.

Improperly adjusting master settings may cause

the system to operate incorrectly. Before entering master settings please contact your professional water dealer.

From the Settings screen, press the Settings button A warning message appears.

Figure 11 Master Settings Warning Screen

After entering the correct password and pressing , the main Master Settings screen is displayed.

Figure 13 Main Master Settings Screen

While in the Master Settings screens, press set parameters to a custom profile (see "NONFACTORY SETTINGS" on page 13 or press the Home button to the Home screen.

Features of the Master Settings screens are described below. See MASTER SETTINGS PROGRAMMING and MASTER SETTINGS REFERENCE CHART for more detailed information.

• format: Contains settings for Language, Units, Hardness Units, Assistance Name, Assistance Phone, and Assistance Interval.

• valve: Contains settings for System, Valve, and Regeneration Type.

• regen: Contains settings for Regen Flow.

• relay: Contains settings for Aux 1 and Aux 2 relays.

• meter: (except for time clock systems) Contains settings

for Meter Types, emergency regeneration.

• settings review: Displays a summary of all programmed settings.

to save all

to return

Press return to the Home screen.

The Password screen displays a numeric keypad.

to continue to the Password screen or press to

Figure 12 Password Screen

• Enter the master settings password 1201 and press continue to the main Master Settings screen, or press to return to the Home screen.

MASTER SETTINGS PROGRAMMING

FLECK 5800/5810/5812 XTRI Service Manual • 9

Page 10

CAUTION

MASTER SETTINGS PROGRAMMING

(continued)

The following is a detailed overview of settings available in Master Settings. Please see the MASTER SETTINGS REFERENCE CHART for the complete set of values and ranges available to program while in Master Settings.

Format Screen

From the main Master Settings screen (Figure 13) press the format button to display the Format screen.

Figure 14 Format Screen

• language: Displays the language used on the control (international version only): English, French, German, Italian, Spanish, or Dutch.

• units: Contains settings for the unit type (either US or Metric) to be used in the control.

• hardness units: Contains settings for hardness units of measure (grains per gallon, mg/L or ppm, German degrees, French degrees, or English degrees). Hardness units are adjustable only if metric units are selected.

NOTE: Degree hardness units are converted to ppm upon

• Press the screen navigation arrows at the upper-right

• Press

input. Degree inputs may be rounded up or down to the nearest ppm equivalent.

and left of the screen to navigate to the Assistance Name, Assistance Phone, and Assistance Interval screens.

to save changes.

Valve Screen

From the main Master Settings screen (Figure 13) press the valve button to display the Valve screen.

Figure 15 Valve Screen

• system: Displays the system type. Type 4 (single system) is currently the only available selection.

• valve: Contains settings to select the valve model installed with the control.

• regen type: Contains settings for the type of regeneration to use for the system. Regeneration types are described in detail below.

Regeneration Types

The XTRI control supports several different Regeneration Types. The Regeneration Type defines the method of automatic regeneration for the system. Each type is explained below.

Time Clock

Triggers a regeneration on a timed interval. The control will initiate a regeneration cycle at the selected Regeneration Time when the number of days since the last regeneration equals the Day Override value. The Day Override can be set from 1 - 99 days as well as partial day intervals of 4, 8, 12, 16 and 20 hours.

Softener Immediate

Measures water usage and regenerates the system as soon as the calculated system capacity is depleted. The control calculates the system capacity by dividing the unit capacity by the feed water hardness. Softener Immediate systems do not use a reserve volume. The control will also start a regeneration cycle at the programmed regeneration time if a number of days equal to the Day Override pass before water usage depletes the calculated system capacity. The Day Override parameter default is OFF, and REGEN TIME will be grayed out unless the day override value has been modified.

When setting the system for softener immediate

regeneration, setting the capacity to a value lower than that of feed water hardness may cause the system to constantly regenerate. If this occurs, disconnect the motor from the control and correct the capacity and feed water hardness values in Master Settings.

Softener Delayed

Measures water usage and regenerates the system at the selected Regeneration Time after the calculated system capacity is depleted. The control calculates the system capacity by dividing the unit capacity by the feed water hardness and subtracting the reserve.

10 • FLECK 5800/5810/5812 XTRI Service Manual

Page 11

The reserve should be set to ensure that the system delivers

CAUTION

treated water between the time the system capacity is depleted and the actual regeneration time. Reserves can be set at a Fixed Volume, Fixed Percentage of capacity, a Variable Reserve based on the previous calendar day's water usage, or a Weekly Reserve based on the average water usage for the current day of the week. The default for the day override parameter is OFF, and the default reserve type is Weekly Reserve.

A Softener Delayed control will also start a regeneration cycle at the selected Regeneration Time if a number of days equal to the Day Override pass before water usage depletes the calculated system capacity.

If the regen type is changed from Softener Immediate to Softener Delayed (or vice-versa), all parameters within those types will be reset to factory default.

Filter Immediate

Regenerates the system immediately after the selected Volume Override value is depleted. A Filter Immediate control will also start a regeneration cycle at the selected Regeneration Time if a number of days equal to the Day Override pass before water usage depletes the calculated system capacity.

Filter Delayed

Regenerates the system at the selected Regeneration Time after the selected Volume Override value is depleted. A Filter Delayed control will also start a regeneration cycle at the selected Regeneration Time if a number of days equal to the Day Override pass before water usage depletes the calculated system capacity.

NOTE: If Filter Immediate or Filter Delayed are selected,

Regenerant Flow selections are limited to Filter, Upflow Filter, Custom Filter, and Custom Upflow Filter.

• regen flow: Contains settings for the type of regenerant

flow to be used in the valve. Changes to this setting affects the cycle steps displayed in the Regeneration Cycle Wheel on the Home screen. Regenerant flow cycle steps are described below.

• downflow: Cycle steps are as follows: Backwash, Draw, Rapid Rinse, Tank Refill

• upflow: Cycle steps are as follows: Draw, Backwash, Rapid Rinse, Tank Refill

• downflow 2X backwash: Cycle steps are as follows: Backwash, Draw, Backwash, Rapid Rinse, Tank Refill

• custom upflow / downflow / filter: Allows for up to 20 programmable cycle steps.

• variable refill: (softener delayed only) Cycle steps are as follows: Refill, Pause, Draw, Backwash, Rinse. Variable refill calculates refill time based on salt dosage, media volume, and BLFC size.

Relay Output Screen

From the main Master Settings screen (Figure 13) press the

relay button to display the Relay Outputs screen.

Regeneration Screen

From the main Master Settings screen (Figure 13) press the regen button to display the Regeneration screen.

Figure 16 Regeneration Screen

Adjusting Regeneration settings will turn any set

relays off. Any required relays will need to be reprogrammed in the Relay Output screen.

• auxiliary 1 / auxiliary 2: Contains settings for

programming up to two auxiliary relay outputs. There are three types of relays that can be programmed:

• Cycle Based: The relay will turn on when the valve moves to the specified regeneration cycle steps. To program, select each cycle step button for which the relay should turn on.

• Time Based: The relay will turn on and off at up to two specified start and end times. If water saving regeneration is on, this is not an available option.

• Volume Based: The relay will turn on when the valve has treated a specified volume of water. Duration can be set for up to two hours.

• Alarm Based: The relay will turn on when the specified alarm condition (or any alarm condition) is met. The relay will turn off when the alarm is cleared.

FLECK 5800/5810/5812 XTRI Service Manual • 11

Page 12

MASTER SETTINGS PROGRAMMING

(continued)

Meter Screen

From the main Master Settings screen (Figure 13) press the meter button to display the Meter screen.

Figure 17 Meter Screen

• meter type: Contains settings for the type of meter installed with the system. The 5810/5812 valve uses an internal 1.25" turbine meter.

• generic: A generic option is available if the installed meter does not match any other selection. Requires setting the number of pulses per volume to ensure proper metering.

• emergency regen: When on, the emergency regen feature causes a regen to occur immediately when 105% or greater of the capacity (e.g., volume plus reserve)

Continuous Flow Detect Screen

From the Meter screen (Figure 19) press to display the Continuous Flow Detect screen.

is used.

Settings Review

From the main Master Settings screen (Figure 13) press the settings review button to display the Settings Review screens, which display a read-only summary of all programmed settings in the control. Use the navigation arrows at the top of the screen to scroll through the parameters currently set in the control. The Settings Review screens are formatted similarly to the corresponding screen where each parameter was set. Press

to return to Master Settings.

Non-Factory Settings

After all parameters in Master Programming have been set, these settings can be saved to a custom profile by pressing on the main Master Settings screen (Figure 13). After pressing

, the Non-Factory Settings screen appears.

Figure 19 Non-Factory Settings Screen

Press to non-factory settings. At any point, the control can be reset to these saved custom settings. By performing a custom reset, any setting that is subsequently programmed without saving to non-factory settings will be reset to the previously saved nonfactory settings in the control.

to save all programmed Master Settings parameters

Figure 18 Continuous Flow Detect Screen

• continuous flow detect: When active, triggers an alarm when continuous flow of 0.5 GPM or 1 LPM is detected by the flow meter over an 8-hour period.

• Press the screen.

12 • FLECK 5800/5810/5812 XTRI Service Manual

button when finished to return to the Home

Page 13

ADDITIONAL FEATURES

Press the screen navigation arrow at the top right of the Master Settings screen (Figure 13) to navigate to the secondary Master Settings screen.

Figure 20 Secondary Master Settings Screen

• water saver regen: Contains settings for setting regenerations to save water by reducing backwash and rinse time on a particular interval

• remote regen: Contains settings for triggering a regeneration via a remote input

• cl generation/low salt: (international version only) Contains settings to trigger chlorine generator for the control

Water Saver Regeneration

From the secondary Master Settings screen (Figure 22) press the water saver regen. button to display the Water Saver Regen screen (Figure 23).

From the secondary Master Settings screen (Figure 22) press the remote regen button to display the Remote Regen screen.

Figure 22 Remote Regeneration Screen

• remote regeneration duration: Contains settings for triggering a regeneration via a remote input. Select a value in seconds that the remote switch must be closed in order to trigger the regeneration.

Connect a remote switch (such as a differential pressure switch) to the remote start input terminals on the back of the XTRI control board. When the remote switch remains closed for the number of seconds specified in the Remote Regen screen, a regeneration will be triggered regardless of volume, capacity, or time remaining until the next scheduled regeneration.

Chlorine Generation/Low Salt (international version only)

From the secondary Master Settings screen (Figure 22) press the cl generation/low salt button to display the Chlorine Gen/ Low Salt screen (Figure 25).

Figure 21 Water Saver Regen Screen

• water saver regen: reduces backwash and rapid rinse times on a particular interval. The reduced backwash time is 50% less than the backwash time (rounded down to the nearest minute, e.g. if the backwash time is set to 10 minutes, enabling the water saver regen function will reduce the backwash time to 5 minutes).The reduced rapid rinse time is 66% less than the rapid rinse time (rounded down to the nearest minute, e.g. if the rapid rinse time is set to 10 minutes, enabling the water saver regen function will reduce the backwash time to 3 minutes).

• range: 1-25 regenerations (for example, a setting of 3 will produce 1 normal regeneration then 3 reduced water saving regenerations).

Figure 23 Chlorine Gen/Low Salt Screen

• cl generation/low salt: Contains settings to trigger chlorine generator for the control (on/off)

• regen interval range: 1 to 255 regenerations

FLECK 5800/5810/5812 XTRI Service Manual • 13

Page 14

REGENERATION

CAUTION

Start a regeneration by pressing the Regeneration button . The Regeneration screen appears (Figure 26).

Figure 24 Regeneration Screen

• Press now to begin a regeneration immediately, or press at regen. time to queue the regeneration for the programmed regeneration time (2:00 AM default for softeners, 12:00 AM default for filters). Pressing at regen. time again will cancel the manual regeneration.

• During Regeneration, press the advance to the next cycle step. Once in regeneration, the volume or time will be displayed below the

For softener systems, put salt in the brine tank before starting a regeneration.

NOTE: Do not use granulated or rock salt.

The unit is now fully programmed and ready to treat water. This quick setup uses the control's default settings, which are appropriate for most residential applications.

button to immediately

button.

CONTROL OPERATION

Control Operation During Regeneration

During regeneration, the Regeneration Cycle Wheel shows the regeneration step the valve is advancing to, or has reached, and the time remaining in that step. Once all regeneration steps are complete the valve returns to treatment position and resumes normal operation. The time remaining in regeneration will be displayed on the home screen in hours and minutes.

Pressing the immediately advances the valve to the next cycle step position and resumes normal step timing. The when the valve is in position and the motor has stopped. Pressing the

button during a regeneration cycle

button is only shown

button will cancel the regeneration.

are stored in a non-volatile memory and are stored indefinitely with or without power. After a long power outage, the Time of Day button may flash indicating it needs to be reset. Press the button to stop the Time of Day from flashing and reset time if needed. If power fails while the unit is in regeneration, the control will save the current valve position before it shuts down. When power is restored, the control will resume the regeneration cycle from the point where power failed. If power remains off for more than eight hours, upon power restoration the regeneration is canceled and the piston returns to service.

If power fails during a regeneration cycle, the

valve will remain in its current position until power is restored. The valve system should include all required safety components to prevent overflows resulting from a power failure during regeneration.

The control will not start a new regeneration cycle without power. If the valve misses a scheduled regeneration due to a power failure, it will queue a regeneration. Once power is restored, the control will initiate a regeneration cycle the next time that the Time of Day equals the programmed regeneration time. Typically, this means that the valve will regenerate one day after it was originally scheduled. If the treated water output is important and power interruptions are expected, the system should be set up with a sufficient reserve capacity to compensate for regeneration delays.

Remote Lockout

If a remote switch is installed, the control will not allow the system to go into regeneration until the regeneration lockout input signal to the control is cleared. This requires opening the contact closure to clear the lockout condition. The recommended gauge wire is 20 with a maximum length of 500 feet. See "WIRING DIAGRAM" on page 43.

Sleep Mode

The control will go into sleep mode if no button is pressed after five minutes. All other control functions will continue to operate. The display will wake from sleep mode when any part of the display is touched.

MASTER RESET

Press the button while in the Master Settings main screen (Figure 13) to display the Reset screen.

Control Operation During Programming

The control can only be programmed with the valve in treatment. While being programmed the control continues to operate normally, monitoring water usage and keeping all displays up to date. Control programming is stored in memory permanently until reset.

Control Operation During a Power Failure

The XTRI includes internal power backup. In the event of power failure, the control shifts into a power-saving mode. The control stops monitoring water usage. The display and motor shut down, but it continues to keep track of the time and day for a minimum of eight hours. The system configuration settings

14 • FLECK 5800/5810/5812 XTR I Service Manual

Figure 25 Reset Screen

Press the factory button to reset all control parameters to their factory defaults, or press the non-factory button to reset control parameters to previously saved custom settings (see "NONFACTORY SETTINGS" on page 13). A warning screen appears before parameters are reset. Press reset or press

to return to Master Settings.

to confirm the

Page 15

DIAGNOSTICS

The control records and displays a variety of diagnostic data to assist with troubleshooting performance issues and fine-tuning system efficiency. Press the Diagnostics button Master Settings or Home screens to view the Diagnostic screen.

Figure 26 Diagnostic Screen

• Press the screen navigation arrows at the upper-right and left of the screen to view each diagnostic parameter.

• Press the Error Log button

to access the Error Log (Figure 29) screen. To clear the Error Log, press the Reset button then the Reset button again on the Clear All Error Logs screen, then enter "1201" at the password prompt screen, then press the Accept button to confirm.

from the

NOTE: If a regeneration occurs while in the Diagnostic screen,

the unit will return to the main screen.

Parameter Description

Flow Rate Displays the current flow rate.

Peak Flow* Displays maximum flow rate of water along

Totalizer*

Last Regen Displays when last regeneration occurred.

Software Version Displays the software version installed on

No of Regens Displays how many manually and system

Regen Interval Displays the average length of time between

Daily Usage Displays average water usage for each day of

Usage Since Regen Displays water usage since last regeneration.

Last Setting Change Displays the date and time of the last update

** Displays total volume of water used since

Reserve Displays the reserve volume based on the

with date and time of occurrence, since last

reset.

last reset.

reserve type selected under master settings.

*This parameter is only available for meter

delayed regeneration type.

the controller.

initiated regenerations the system has gone

through since last reset.

regenerations based on the past four

regenerations.

the week based on the usage on that day for

the past six weeks.

to Master Settings.

NOTE*: Only Peak Flow and Totalizer can be changed - they

can be reset to zero.

NOTE**: Totalizer has a maximum value of 99,999,999. If this

number is reached, the Totalizer must be reset to zero to continue tracking this value.

Figure 27 Error Log Screen

Press the Home button

to return to the Home screen.

ALARMS AND ERRORS

If an error in valve or control function occurs, an alarm will sound and the Home screen will display the Error

Alert button

• Press the Alarm button to mute the alarm.

• Press the Error Alert button to view information about the error.

and the Alarm button .

Error Alert

Alarm

Figure 28 Alarm and Error Alert

FLECK 5800/5810/5812 XTRI Service Manual • 15

Page 16

If the display is in sleep mode when an error occurs, the screen will turn on for five minutes. The error will beep for one second per minute until the error is cleared. If the error is not cleared after five minutes, the screen will switch to power saving mode and display the Error Alert button as a screen saver.

See TROUBLESHOOTING for more information about error conditions.

USB Connection for Field Programming

The XTRI features a USB port that allows you to connect a PC to the control for field programming and diagnostic parameter download.

NOTE: Field Programmer software is required for field

Pressing

programming features. See XTRI Field Programmer Manual for more information on using the Field Programmer software.

on the Format screen displays the USB screen.

Figure 29 USB Screen

When the USB screen appears, connect a USB cable to the USB port on the control circuit board. Connect the other end of the USB cable to a PC with the Field Programmer software installed and follow the directions in the XTRI Field Programmer manual to complete the connection. Press return to Master Settings.

NOTE: Do not remove USB cable from computer or control

while connected and transferring data. See the XTRI Field Programmer manual for proper disconnection procedure.

16 • FLECK 5800/5810/5812 XTRI Service Manual

Page 17

TROUBLESHOOTING

Problem Cause Correction

Valve constantly

regenerates

Error Alerts

NOTE: An Error Alert appears on the Home screen if an error condition is detected. Press the Error Alert button to view the

error message.

NOTE: Most error alerts are cleared at regeneration. If the error persists following a regeneration attempt the appropriate

reset and recovery procedure below or contact technical support.

Error in programming has caused

a regeneration loop condition in the

control.

Disconnect the motor from the control circuit board (see "WIRING DIAGRAM" on page 43 for location on circuit board). A Motor Stall error will occur, allowing access to Master Settings. Navigate to the Valve screen and check Regen Type settings. Ensure that the value for Capacity is larger than the value for Hardness, and save settings.

If the error continues to occur, unplug the unit, put it into bypass and contact technical support.

Error Screen

Display

Motor Stall

Motor Run-On

No changes

detected in the

optical sensor for 6

seconds

Optical Sensor

Undesired change

detected in the

optical sensor

Flow meter error Continuous Flow

Over current

Motor over current

detected

Flow meter error No flow detected Flow meter

No regeneration for

100 days

Service Interval Service Interval

No Salt Detect

(international

version only)

Emergency Regen

Occurred

App Display Cause Reset and Recovery

Motor stall

Optical sensor

Flow meter

Over current

No regen

100 day

No Salt Detect

Emer Reg

Occur

No state changes in

the optical sensor

are detected for six

seconds.

An undesired optical sensor state change

occurred.

The flow meter has

reported continuous

flow for more than 24

hours.

Motor drew too much

current

No flow has been

detected for 7 days.

The valve has not

regenerated in more

than 100 days.

Service Interval timer

has expired.

When chlorine

generator is on but does not read salt from the chlorine generator.

Over 105% of the total

capacity (e.g., volume

plus reserve) has been

depleted

Unplug the unit and plug back in. Allow the control to attempt to find position again.

Verify the optical sensor is in place with the wires connected to the circuit board. Verify the motor and drive train components are in good condition and assembled properly. Check the valve and verify that the piston travels freely. Replace/reassemble the various components as necessary.

Plug the unit back in and observe its behavior. If the error reoccurs, unplug the unit, put it into bypass and contact technical support.

Non-critical error. Extra optical sensor pulse detected. Press the Regeneration button to advance motor to clear error.

Error will clear when flow to meter drops below 0.5 GPM or 1 LPM. If continuous flow is expected, turn plumbing leak detection off in Master Settings.

Attempt to perform a manual regeneration. If error continues, call technical support.

Error will clear when a flow pulse is detected. Check to ensure meter cable is properly installed and meter spins freely. Clear meter of debris if necessary. If error continues, call technical support.

Initiate a regeneration.

From within Master Settings, navigate to the Assistance/Mainten. Interval screen and set a new Service Interval time.

Error will clear if salt is added to the brine tank and a manual regeneration is performed.

Error will clear when regeneration occurs. When the Emergency Regen is enabled, the Emergency Regen Occurred error alert will display to let the user know an Emergency Regen Occurred. Repeated Emergency Regen may indicate an undersized system.

IOT Conn

Failure

Offline

XTRI & IOT Board

Communication not

working

WiFi Connection has

been disrupted for

more than 60 minutes

Remove data cable. Reset IOT Board by reset button on top, then plug data cable back in.

Verify WiFi is not experiencing any issues.

FLECK 5800/5810/5812 XTR I Service Manual • 17

Page 18

PENTAIR PRO: APP SETUP

Pairing the Fleck 5800/5810/5812 XTRI Connected Valve with Wi-Fi Devices

The Fleck 5800/5810/5812 XTRI Connected Valve can be paired with a smartphone or tablet. New users can download and install the Pentair Home App from the App Store or Google Play. WiFi connection must be 4G or less.

New users will need to create an account to monitor their water softeners. From the Log In page, press a new account. If you already have an account, skip to Login.

Once you press Create Account, an email will be sent to the email for verification.

Click the “Verify Email” link to complete the process.

Add your email address and set your password.

18 • FLECK 5800/5810/5812 XTR I Service Manual

Page 19

Sign into the app with your verified email and password.

If you have a Pentair Partner Center Account, you should select yes you are a participant. If you will be the main administrator for the Pro account, then select Admin. (Employees will be able to be invited to be part of your Pro app team through the Pentair Dealer Web App.) The Pentair ID and password is your Partner Center email and password.

Once you sign in, the app will take you through the following series of screens.

(Your Pentair Center email)

(Your Password)

Available only by Admin by invitation.

FLECK 5800/5810/5812 XTRI Service Manual • 19

Page 20

In the event you are not a Partner Center user, then please select No and proceed through the log in pages. This will provide for limited screens and options.

After pressing CONTINUE, the app will then take you to the dashboard. To add a device click on the + sign.

Once in the app, it will take you through a Create a Profile screen. Once you create your profile, click the save button at the bottom of the screen. This will take you to the main dashboard.

Select Water Treatment, Water Softener.

20 • FLECK 5800/5810/5812 XTR I Service Manual

Page 21

The screens will now take you through the provisioning process.

2. Turn the Bluetooth to “ON” and then click the check mark at the bottom right hand corner.

3. A Bluetooth icon will appear in the upper right hand corner of the main screen.

You are now ready to provision your valve.

1. From the XTRI control, press the gear button main screen to proceed to settings.

Settings

on the

a. A black icon

but not connected.

b. A white icon reflects the Bluetooth signal is open

and connected.

c. The alert icon will show up on the screen until a

WiFi connection has been established.

4. Once the Bluetooth signal is open the continue button on the app to scan for the device.

reflects the Bluetooth is open,

on the screen, press

FLECK 5800/5810/5812 XTR I Service Manual • 21

Page 22

5. A list of available devices will appear. Once the device is found, select that device from the list.

(Your device)

7. Once pairing is complete, if you are using the Pentair Pro App, set up is complete.

6. Authorize the pairing of the device by clicking “Pair”.

If you are using the Pentair Home app, please proceed to the screens to set up the WiFi connections as referenced in the Homeowner Manual.

8. In the app the product will now show up in your installed devices.

22 • FLECK 5800/5810/5812 XTR I Service Manual

Page 23

MASTER SETTINGS REFERENCE CHART

CAUTION

Before entering Master Settings, please contact your local professional water dealer.

Screen Name Parameters Values Notes

Format Language English, French,

Units U.S.

Hardness Units Grains per gallon

Assistance Name Free-form text A - Z and space Name of service provider to display when viewing the Assistance screen. 20 character limit.

Assistance Phone Free-form text 0 - 9 and space Phone number of service provider to display when viewing the Assistance screen. 20 character limit.

Assistance Interval Month Based

Valve System 4 System 4 (single system) is currently the only available selection.

Regeneration Regen. Flow Upflow

Regen Based

Valve 5800

Media Volume 0.25 - 999.00 ft

Salt Dosage 3 - 18 lbs/ft

BLFC size 0.125 gpm

Regen. Type Time Clock

Capacity 1 - 99 999 999

Hardness 1 - 199 grains/gallon

Reserve Fixed %

Day Override 1 - 99 days

Regen Time 12 / 24 hour clock Required for Time Clock and delayed Regeneration Types. Set for immediate regeneration types only when a

Volume Override 1 - 99 999 999 gallons / liters Only displayed when Regeneration Type is Filter Immediate or Filter Delayed.

German, Italian,

Spanish, Dutch

Metric

mg/L or ppm

German degrees

French degrees

English degrees

1 - 60

1 - 2000

Off

5810 5812

1 - 9999 L

50 - 290 g/L

0.250 gpm

0.500 gpm

1.000 gpm

Softener Immediate

Softener Delayed

Filter Immediate

Filter Delayed

grains / grams / degrees

1 - 1 999 mg/liter

x - x degrees

Fixed Volume

Weekly Reserve

Variable Reserve

4, 8, 12, 16, 20 hours

Downflow

Downflow 2x Backwash

Custom Upflow/Downflow/Filter

Filter

Variable Refill

Changes the language to display screen text and button labels in the control (available with international version of control only).

Changes system units and values across all parameters in the control. All programmed units and values should be recalculated after adjusting this setting.

Changes hardness units used in displaying hardness parameters and calculating system capacity and editing exchange capacity and hardness settings.

Set to automatically display the Assistance screen after a certain number of months or regenerations.

Select the type of valve to be installed.

Used to calculate capacity.

Used to calculate capacity and refill time.

Brine Line Flow Control; Used to calculate refill time.

Regeneration Types are described in detail on page 11. Additional Valve screen parameters are dependent upon selected Regeneration Type. Not all parameters will be displayed. Softener Delayed regeneration type has four reserve options (Fixed %, Fixed Volume, Variable Reserve, Weekly Reserve). The control will display additional configuration options depending on the selected reserve type.

Only required on metered systems to calculate treated water capacity and reserve. Represents total system capacity between regenerations.

Only required on metered systems to calculate treated water capacity and reserve. Represents hardness of untreated water.

Only available when Meter Delayed regeneration type is selected. Selecting Fixed % or Fixed Volume will display additional configuration options. Weekly Reserve is calculated based on average day of week's water usage. Variable Reserve is calculated based on previous day's water usage.

Available to be programmed for all Regeneration Types.

Day Override is also set.

Cycle steps on the Home screen and during regeneration will change to reflect the cycle steps and order in the selected Regenerant Flow. Additional Regeneration screen parameters are dependent upon selected Regenerant Flow. Not all parameters will be displayed. Custom Upflow and Downflow allows for up to 20 programmable cycle steps. Variable Refill calculates refill time based on Salt Dosage, Media Volume, and BLFC Size. Time per cycle step can be programmed for all other Regenerant Flow options.

Relay Outputs Aux 1/Aux 2 Cycle Based

Meter Meter Type .75 inch Turbine

Generic 1 - 999.9 /1 - 1500

Remote Regen Remote Regen 1 - 255 seconds

NOTE: Some items may not be shown depending on control configuration. The control will discard any changes and exit Master Settings if any button is not pressed for five minutes.

Time Based

Volume Based

Alarm Based

Off

.75 inch Paddle

1.00 inch Paddle

1.25 inch Turbine

1.50 inch Paddle

1.50 inch Turbine

2.00 inch Paddle

3.00 inch Paddle Generic

pulses per gallon / liter

Off

For Cycle Based relays, select the cycle steps on which the relays will turn on. For Time Based relays, two start/end times will need to be selected for each relay. Relay times are based on total regeneration cycle time. Volume Based relays can be programmed from zero gallons/liters to the full system capacity. Duration can be set from zero seconds to two hours. Volume Based option is not available when Regeneration Type is set to Time Clock. Alarm Based relays will turn on when an alarm condition is met, and will turn off when the alarm is cleared.

Select the type of meter installed with the system. A Generic option is available if the installed meter does not match any other selection. Selecting the Generic meter type requires setting the number of pulses per gallon or liter to ensure proper metering.

Only available when Generic meter type is selected.

Select a value in seconds that the remote switch must be closed in order to trigger the regeneration.

FLECK 5800/5810/5812 XTRI Service Manual • 23

Page 24

5800 CONTROL VALVE PART NUMBERS

Item No. QTY Part No. Description

1 ................... 1 ......... 580008-004 ........... Turbine Meter, Downflow Softener, U.S. Power

.......... 580008-005 ........... Turbine Meter, Upflow Softener, U.S. Power Supply,

.......... 580008-006 ........... Time Clock B/W Filter, U.S. Power Supply

Supply, #00 Injector, 0.125 GPM BLFC

#00 Injector, 0.125 GPM BLFC

NOTE: Above part numbers DO NOT include the following parts.

Bezel Bypass Assembly Connector Assembly Flow Washer DLFC

See 5800 accessories page for options.

5810 CONTROL VALVE PART NUMBERS

Item No. QTY Part No. Description

1 ................... 1 ......... 581008-005 ...........

.......... 581008-006 ........... 1.25" Integral Meter, Upflow Softener, U.S. Power Supply,

.......... 581008-007 ........... Time Clock B/W Filter, U.S. Power Supply

NOTE: Above part numbers DO NOT include the following parts:

Bezel Distributor Pilot Bypass Assembly Connector Assembly Flow Washer DLFC

See 5810/5812 accessories page for options.

1.25" Integral Meter, Downflow Softener, U.S. Power Supply, #00 Injector, 0.125 GPM BLFC

#00 Injector, 0.125 GPM BLFC

5812 CONTROL VALVE PART NUMBERS

Item No. QTY Part No. Description

1 ................... 1 ......... 581208-0010 ......... 1.25" Integral Meter, Downflow Softener, U.S. Power Supply,

.......... 581208-0011 ......... Time Clock B/W Filter, U.S. Power Supply, 4" Base,

.......... 581208-0012 ......... Time Clock B/W Filter, INT'L Power Supply, 4" Base,

NOTE: Above part numbers DO NOT include the following parts.

Bezel Distributor Pilot (except on 4" base models) Bypass Assembly Connector Assembly Flow Washer DLFC

See 5810/5812 accessories page for options.

24 • FLECK 5800/5810/5812 XTR I Service Manual

2.5" Base, Less Distributor Pilot, #00 Injector, 0.125 GPM BLFC

1.9" OD Distributor Pilot

Page 25

POWERHEAD ASSEMBLY

Item No. QTY Part No. Description

1.................1 ........ 43261 .................Cover, Black

2.................1 ........ 43262-00 ............Bezel, Blue

......... 43262-01 ............Bezel, Black

......... 43262-02 ............Bezel, Silver

3.................1 ........ 61957 .................Panel Gear Assy, 5800/5810/5812

4.................1 ........ 62126 .................Timer Assy, 5800XTR Touch Scrn

5.................1 ........ 61835 .................Motor Assembly

6.................1 ........ 61882 .................Cover Assy, Environmental, 5800, Gray

61994 .................Cover Assy, Environmental, 5810/12, Gray

7.................1 ........ 44161 .................Transformer, 12V UL

8.................1 ........ 44162 .................Transformer, Intl, 12V UL

9.................1 ........ 43715 .................Cover, Lower, Black, 5800

10 ...............1 ........ 62125 .................Kit, IOT Module, 5800 XTRI

w/Logo, International Lang

FLECK 5800/5810/5812 XTR I Service Manual • 25

Page 26

5800 CONTROL VALVE ASSEMBLY

CAUTION

Item No. QTY Part No. Description

1 ................... 1 ......... 61857-01 ............... Valve Body Assy, Downflow/Upflow

................................. 61857-20 ............... Valve Body Assy, Mixing, Downflow/

2 ................... 1 ......... 18271 .................... Screen Injector, 5800

3 ................... 1 ......... 40064 .................... Seal Injector

4 ................... 1 ......... 18277 .................... Cap Injector

.......... 18278-20 ............... Injector Cap Assy, 1610 Regulated,

.......... 18278-30 ............... Injector Cap Assy, 1610 Regulated,

5 ................... 2 ......... 18262 .................... Screw, Hex Washer Head, #10-24 x

6 ................... 1 ......... 19654 .................... Label, 0.125 gpm Brine Flow

.......... 12128 .................... Label, 0.25 gpm BLFC

.......... 10759 .................... Label, 0.5 gpm 1.5 lbs Salt/Min

.......... 10760 .................... Label, 1.0 gpm 3 lbs Salt/Min

7 ................... 1 ......... 13333 .................... Label, Injector, Blank

8 ................... 3 ......... 18261 .................... Screw, Hex Washer Head, #10-24 0.81

9 ................... 1 ......... 13304 .................... O-ring, -121

10 ................. 1 ......... 18303-01 ............... O-ring, -336, 560CD

11 ................. 1 ......... 13030 .................... Retainer, Distributor Tube O-ring

12 ................. 1 ......... 18312 .................... DLFC Housing Retainer Clip

13 ............................. 61837 .................... Piston and Seal Kit Assy, Downflow,

.......... 61838 .................... Piston and Seal Kit Assy, Upflow, 5800

14 ................. 1 ......... 60032 .................... Brine Valve, 4600/5600

15 ................. 1 ......... 13302 .................... O-ring, -014

16 ............................. 60022-12 ............... BLFC, 0.125 gpm

.......... 60022-25 ............... BLFC, 0.25 gpm

.......... 60022-50 ............... BLFC, 0.5 gpm

.......... 60022-100 ............. BLFC, 1.0 gpm

17 ..........60705-00 ............... DLFC, Plastic, Blank

.......... 60706-8.0 .............. DLFC, QC x 3/4"F, 8.0 GPM

.......... 60706-9.0 .............. DLFC, QC x 3/4"F, 9.0 GPM

(Includes Items 9, 10, 11, 12)

Upflow (Includes Items 9, 10, 11, 12)

5800, 20 psi, Black, Upflow

5800, 30 psi, Gray, Upflow

1.00

5800

.......... 60706-10 ............... DLFC, QC x 3/4"F, 10 GPM

.......... 60706-12 ............... DLFC, QC x 3/4"F, 12 GPM

.......... 60706-15 ............... DLFC, QC x 3/4"F, 15 GPM

18 ............................. 19153 .................... Washer, Flow, 0.6 GPM

.......... 19152 .................... Washer, Flow, 0.8 GPM

.......... 12085 .................... Washer, Flow, 1.2 GPM

.......... 19150 .................... Washer, Flow, 1.3 GPM

.......... 12086 .................... Washer, Flow, 1.5 GPM

.......... 12087 .................... Washer, Flow, 2.0 GPM

.......... 12088 .................... Washer, Flow, 2.4 GPM

.......... 12089 .................... Washer, Flow, 3.0 GPM

.......... 12090 .................... Washer, Flow, 3.5 GPM

.......... 12091 .................... Washer, Flow, 4.0 GPM

.......... 19147 .................... Washer, Flow, 4.5 GPM

.......... 12092 .................... Washer, Flow, 5.0 GPM

.......... 17814 .................... Washer, Flow, 6.0 GPM

.......... 12408 .................... Washer, Flow, 7.0 GPM

19 ............................. 18272-000 ............. Injector Assy, 1610, #000, Brown

.......... 18272-00 ............... Injector Assy, 1610, #00, Violet

.......... 18272-0 ................. Injector Assy, 1610, #0, Red

.......... 18272-1 ................. Injector Assy, 1610, #1, White

.......... 18272-2 ................. Injector Assy, 1610, #2, Blue

.......... 18272-3 ................. Injector Assy, 1610, #3, Yellow

20 ............................. 18276-01 ............... Injector Assy, Plug, w/O-rings

Not Shown:

.......... 40947-01 ............... Plug, Brine Valve, w/O-ring, 560CD

.......... 13918-01 ............... BLFC Module Plug Assy, w/O-ring

NOTE: In upflow units, the Injector Plug and Injector Assy are put in the

reverse holes. In filter units, both injector holes are plugged with 18276-01.

Excessive side load on piston rod may cause premature

failure.

If seal/spacer stack is stuck in valve bore during disassembly,

rotate stack prior to removal.

BR61500-5800 Rev A

26 • FLECK 5800/5810/5812 XTR I Service Manual

Page 27

5810 CONTROL VALVE ASSEMBLY

Item No. QTY Part No. Description

1 ................... 1 ......... 61961 .................... Kit, Mounting, 5810/5812

2 ................... 1 ......... 61956-01 ............... Kit, Piston, Seal, and Spacer, 5810,

.......... 61956-02 ............... Kit, Piston, Seal, and Spacer, 5810,

.......... 61956-03 ............... Kit, Piston, Seal, and Spacer, 5810,

3 ................... 1 ......... 19791-01 ............... Assy, Meter Cable

4 ................... 1 ......... 60016-01 ............... Brine Valve

5 ................... 1 ......... 40947 .................... Plug, Brine Valve

6 ................... 1 ......... 13302 .................... O-ring, -014

7 ................... 1 ......... 61450-00 ............... BLFC Assy 3/8", Blank

.......... 61450-12 ............... BLFC Assy 3/8", .12 GPM

.......... 61450-25 ............... BLFC Assy 3/8", .25 GPM

.......... 61450-50 ............... BLFC Assy 3/8", .50 GPM

.......... 61450-100 ............. BLFC Assy 3/8", 1.0 GPM

8 ................... 1 ......... 61451-00 ............... BLFC Assy 1/2", Blank

.......... 61451-12 ............... BLFC Assy 1/2", .12 GPM

.......... 61451-25 ............... BLFC Assy 1/2", .25 GPM

.......... 61451-50 ............... BLFC Assy 1/2", .50 GPM

.......... 61451-100 ............. BLFC Assy 1/2", 1.0 GPM

9 ................... 1 ......... 41056 .................... Nut Assy, 1/2"

10 ................. 2 ......... 40576-01 ............... Clip, H, Plastic

11 ................. 1 ......... 61923-20 ............... Cap, Regulated Injector, 20 PSI

.......... 61923-30 ............... Cap, Regulated Injector, 30 PSI

12 ................. 2 ......... 61958 .................... Injector Cap Assy, w/O-ring

13 ................. 1 ......... 61454-0 ................. Injector Assy, #0, Red

.......... 61454-00 ............... Injector Assy, #00, Violet

.......... 61454-000 ............. Injector Assy, 7000, #000, Brown

.......... 61454-1 ................. Injector Assy, #1, White

.......... 61454-2 ................. Injector Assy, #2, Blue

.......... 61454-3 ................. Injector Assy, #3, Yellow

.......... 61454-4 ................. Injector Assy, #4, Green

.......... 61454-5 ................. Injector Assy, #5, Gray

14 ................. 1 ......... 40945 .................... Clip, Drain Retaining

15 ................. 1 ......... 61959 .................... Injector Plug, w/O-rings

16 ................. 1 ......... 43719 .................... Screen, Injector 5810/5812

17 ................. 1 ......... 40946 .................... Clip, Brine Retaining

18 ................. 1 ......... 61983-01 ............... Valve Body Assy, 5810

.......... 61983-02 ............... Valve Body Assy, 5810, Mixing

19 ................. 1 ......... 61919 .................... Meter Assy, 1-1/4", 5810/5812

20 ................. 1 ......... 61419-02 ............... Kit, 32mm Distributor, Adapter

21 ................. 1 ......... 61419-01 ............... Kit, 1.315" Distributor, Adapter

22 ................. 1 ......... 61419 .................... Kit, 1.05" Distributor Adapter

23 ................. 1 ......... 61455-00 ............... DLFC 3/4", Elbow Blank

24 ............................. 61456-00 ............... DLFC 1", Straight Blank

Downflow

Upflow

Filter

L1487214 REV A

NOTE: Install injector in hole "DF" and plug in hole "UF" for

downflow units. In upflow units the injector plug and injector assembly are installed in reverse holes. In filter units, both injector holes are plugged with 61959. See illustration below.

FLECK 5800/5810/5812 XTRI Service Manual • 27

Page 28

5812 CONTROL VALVE ASSEMBLY

Item No. QTY Part No. Description

1.................1 ........ 61961 .................Kit, Mounting, 5810/5812

2.................1 ........ 61960-01 ............Kit, Piston, Seal, and Spacer,

5812, Downflow

......... 61960-02 ............Kit, Piston, Seal, and Spacer,

5812, Upflow

......... 61960-03 ............Kit, Piston, Seal, and Spacer,

5812, Filter

3.................1 ........ 19791-01 ............Assy, Meter Cable

4.................1 ........ 60016-01 ............Brine Valve

5.................1 ........ 40947 .................Plug, Brine Valve

6.................1 ........ 13302 .................O-ring, -014

7.................1 ........ 61450-00 ............BLFC Assy 3/8", Blank

......... 61450-12 ............BLFC Assy 3/8", .12 GPM

......... 61450-25 ............BLFC Assy 3/8", .25 GPM

......... 61450-50 ............BLFC Assy 3/8", .50 GPM

......... 61450-100 ..........BLFC Assy 3/8", 1.0 GPM

8.................1 ........ 61451-00 ............BLFC Assy 1/2", Blank

......... 61451-12 ............BLFC Assy 1/2", .12 GPM

......... 61451-25 ............BLFC Assy 1/2", .25 GPM

......... 61451-50 ............BLFC Assy 1/2", .50 GPM

......... 61451-100 ..........BLFC Assy 1/2", 1.0 GPM

9.................1 ........ 41056 .................Nut Assy, 1/2"

10 ...............2 ........ 40576-01 ............Clip, H, Plastic

11 ...............1 ........ 61923-20 ............Cap, Regulated Injector, 20 PSI

......... 61923-30 ............Cap, Regulated Injector, 30 PSI

12 ...............1 ........ 61454-0 ..............Injector Assy, #0, Red

......... 61454-00 ............Injector Assy, #00, Violet

......... 61454-000 ..........Injector Assy, 7000, #000, Brown

......... 61454-1 ..............Injector Assy, #1, White

......... 61454-2 ..............Injector Assy, #2, Blue

......... 61454-3 ..............Injector Assy, #3, Yellow

......... 61454-4 ..............Injector Assy, #4, Green

......... 61454-5 ..............Injector Assy, #5, Gray

13 ...............2 ........ 61959 .................Injector Plug, w/O-rings

14 ...............1 ........ 43719 .................Screen, Injector 5810/5812

15 ...............1 ........ 40946 .................Clip, Brine Retaining

16 ...............1 ........ 61984-01 ............Valve Body Assy, 5812, 2-1/2"

Base

......... 61984-11 ............Valve Body Assy, 5812, 4" Base*

......... 61984-02 ............Valve Body Assy, 5812, 2-1/2"

Base, Mixing

17 ...............1 ........ 43596 .................Clip, Drain Retaining

18 ...............1 ........ 61919 .................Meter Assy, 1-1/4", 5810/5812

19 ...............1 ........ 61419-01 ............Kit, 1.315" Distributor Adapter

20 ...............1 ........ 61419-02 ............Kit, 32mm Distributor Adapter

21 ...............1 ........ 61419 .................Kit, 1.05" Distributor Adapter

22 ...............1 ........ 13577-01 ............O-ring, -226, 560CD

23 ...............1 ........ 41747 .................Retainer, Distributor, 1.5"

24 ...............2 ........ 61958 .................Injector Cap Assy, w/O-ring

25 ...............2 ........ 1000269 .............Cap Assembly, Blank

* Includes items 24 and 25. Each valve body is installed with adapters for a 4" tank base and packaged with distributor adapter kits for 1.5" distributors (items 24 and 25).

**See "5812 Valve Accessories"

**See NOTE below.

L1487216 REV A

NOTE: Install injector in hole "DF" and plug in hole "UF" for

downflow units. In upflow units the plug and injector are installed in reverse holes. In filter units, both injector holes are plugged with 61959. See illustration below.

NOTE: Install plug in hole "A" for units that allow hard

water to flow during regeneration. For no hard water bypass (downflow only), install plug in hole "B". See illustration below.

28 • FLECK 5800/5810/5812 XTRI Service Manual

Page 29

5800/5810/5812 VALVE ACCESSORIES

Covers

43261 .............................Cover

43715 .............................Cover, Lower

61994 .............................Cover Assy, Environmental 5810/5812 Gray

61882 .............................Cover Assy, Environmental 5800 Gray

Bezels

43262-00 .......................Bezel, Blue

43262-01 .......................Bezel, Black

43262-02 .......................Bezel, Silver

Adapter Kits (5810, 5812)

61419 ............................Kit, 1.05" Distributor, Adapter

61419-01 .......................Kit, 1.315" Distributor, Adapter

61419-02 .......................Kit, 32mm Distributor, Adapter

Bypasses

43644 .............................Bypass Assembly, 1.25", 5810/12

60040SS.........................3/4” Bypass, SS, NPT (5800 only)

60041SS.........................1” Bypass, SS, NPT (5800 only)

60049 .............................Bypass, Plastic (5800 only)

Connector Assemblies (5810, 5812)

61991-01 .......................Connector Assy, 1" NPT

61991-02 .......................Connector Assy, 1" BSP

61991-03 .......................Connector Assy, 1¼" NPT

61991-04 .......................Connector Assy, 1¼" BSP

61991-05 .......................Connector Assy, ¾"-1" Sweat

61991-06 .......................Connector Assy, 1"-1¼" Sweat

61991-07 .......................Connector Assy, 1¼" - 1½" Sweat

61991-08 .......................Connector Assy, 1½" NPT

61991-09 .......................Connector Assy, 1½" BSP

61991-10 .......................Connector Assy, ¾" & 1" CPVC

61991-11 .......................Connector Assy, 1¼" & 1½" CPVC

Connector Elbow (5810, 5812)

61992 .............................Connector Elbow Assembly

Collectors (5800)

18280 .............................Top Collector, 1.050

18280-01 .......................Top Collector, 1.050 Wide

18280-02 .......................Top Collector, 1.050 Narrow

Power Supplies

44161 .............................Power Supply, US, 12V DC 3M, 2A

44162 .............................Power Supply, INTL, 12V DC 3M, 2A

Washers

19153 ...........................Washer, Flow, 0.6 GPM (5800 only)

19152 ...........................Washer, Flow, 0.8 GPM (5800 only)

12085 ...........................Washer, Flow, 1.2 GPM (5800 only)

19150 ...........................Washer, Flow, 1.3 GPM (5800 only)

12086 ...........................Washer, Flow, 1.5 GPM (5800 only)

19149 .............................Washer, Flow, 1.7 GPM (5810 only)

12087 .............................Washer, Flow, 2.0 GPM (5800, 5810)

12088 .............................Washer, Flow, 2.4 GPM (5800, 5810)

12089 .............................Washer, Flow, 3.0 GPM (5800, 5810, 5812)

12090 .............................Washer, Flow, 3.5 GPM (5800, 5810, 5812)

12091 .............................Washer, Flow, 4.0 GPM (5800, 5810, 5812)

19147 .............................Washer, Flow, 4.5 GPM (5800, 5810, 5812)

12092 .............................Washer, Flow, 5.0 GPM (5800, 5810, 5812)

17814 .............................Washer, Flow, 6.0 GPM (5800, 5810, 5812)

12408 .............................Washer, Flow, 7.0 GPM (5800, 5810, 5812)

17943 .............................Washer, Flow, 8.0 GPM (5810, 5812)

17944 .............................Washer, Flow, 9.0 GPM (5810, 5812)

16529 .............................Washer, Flow, 10.0 GPM (5810, 5812)

16735 .............................Washer, Flow, 12.0 GPM (5810, 5812)

16736 .............................Washer, Flow, 15.0 GPM (5810, 5812)

16528 .............................Washer, Flow, 20.0 GPM (5810, 5812)

16737 .............................Washer, Flow, 25.0 GPM (5810, 5812)

43736 .............................Washer, Flow, 30.0 GPM (5812 Only)

43737 .............................Washer, Flow, 35.0 GPM (5812 Only)

43738 .............................Washer, Flow, 40.0 GPM (5812 Only)

43739 .............................Washer, Flow, 45.0 GPM (5812 Only)

Yokes (5800)

19620-01 .......................Yoke Assy, 3/4", r/angle, 90 deg.

18706 .............................1" Yoke, Plastic NPT

18706-02 .......................3/4" Yoke, Plastic NPT

18706-10 .......................1" Yoke, Plastic BSP

18706-12 .......................3/4" Yoke, Plastic BSP

61694 .............................1" Yoke, QC

61700 .............................3/4" Yoke, QC

13708-40 .......................1” Yoke, Sweat

41026-01 .......................1” Yoke, SS, NPT

42690 .............................3/4” Yoke, Sweat

41027-01 .......................3/4” Yoke, SS, NPT

DLFC (5800)

60705-00 .....................DLFC, Plastic, Blank

60706-8.0 ....................DLFC, QC x 3/4"F, 8.0 GPM

60706-9.0 ....................DLFC, QC x 3/4"F, 9.0 GPM

60706-10 .....................DLFC, QC x 3/4"F, 10 GPM

60706-12 .....................DLFC, QC x 3/4"F, 12 GPM

60706-15 .....................DLFC, QC x 3/4"F, 15 GPM

DLFC (5810)

61455-00 .......................DLFC, ¾", Elbow, NPT, Blank,

For 0.6-7.0 GPM Washers

61456-00 .......................DLFC Assy, 1", Straight, NPT,

For 0.8 - 25 GPM Washers

62088-00 .......................DLFC Assy, 1", Straight, NPT,

Blank,For 8.0 - 25 GPM Washers

61456-30 .......................DLFC Assy, 1", 30 GPM

DLFC (5812)

61971-00 .......................DLFC, 1" NPT, Blank, Elbow, 5812

61974-00 .......................DLFC, 1" BSP, Blank, Elbow, 5812

61977-00 .......................DLFC, 1¼" NPT, Blank, Straight, 5812

61980-00 .......................DLFC, 1¼" BSP, Blank, Straight, 5812

COVER, LOWER

COVER, ENVIRONMENTAL

CONNECTOR ASSY,

STRAIGHT

BYPASS ASSY

ADAPTER KITS

WASHERS

COLLECTORS

YOKES

COVER, BEZEL

CONNECTOR ASS,

ELBOW

POWER SUPPLIES

DLFC

FLECK 5800/5810/5812 XTRI Service Manual • 29

Page 30

5800/5810/5812 VALVE ASSEMBLIES

BLFC

60022-12 ................ BLFC, 0.125 GPM (0.375 lbs NaCl/min) (5800 only)

60022-25 ................ BLFC, 0.25 GPM (0.75 lbs NaCl/min) (5800 only)

60022-50 ................ BLFC, 0.50 GPM (1.5 lbs NaCl/min) (5800 only)

60022-100 .............. BLFC, 1.0 GPM (3 lbs NaCl/min) (5800 only)

61450-00 ................ BLFC, 3/8", Blank (5810, 5812)

61450-12 ................ BLFC, 3/8", 0.125 GPM (5810, 5812)

61450-25 ................ BLFC, 3/8", 0.25 GPM (5810, 5812)

61450-50 ................ BLFC, 3/8", 0.50 GPM (5810, 5812)

61450-100 .............. BLFC, 3/8", 1.0 GPM (5810, 5812)

61451-00 ................ BLFC, 1/2", Blank (5810, 5812)

61451-12 ................ BLFC, 1/2", 0.125 GPM (5810, 5812)

61451-25 ................ BLFC, 1/2", 0.25 GPM (5810, 5812)

61451-50 ................ BLFC, 1/2", 0.50 GPM (5810, 5812)

61451-100 .............. BLFC, 1/2", 1.0 GPM (5810, 5812)

BLFC

Injector Assemblies

18272-000 .............. Injector Assy, 1610, #000, BROWN (8" Tank) (5800 only)

18272-00 ................ Injector Assy, 1610, #00, VIOLET (9" & 10" Tank) (5800 only)

18272-0 .................. Injector Assy, 1610, #0, RED( 12" & 13" Tank) (5800 only)

18272-1 .................. Injector Assy, 1610, #1, WHITE (14" & 16" Tank) (5800 only)

18272-2 .................. Injector Assy, 1610, #2, BLUE (18" Tank) (5800 only)

18272-3 .................. Injector Assy, 1610, #3, YELLOW (20" Tank) (5800 only)

61454-0 .................. Injector Assy, #0 RED (12" & 13" Tank) (5810, 5812)

61454-00 ................ Injector Assy, #00 VIOLET (9" & 10" Tank) (5810, 5812)

61454-000 .............. Injector Assy, #000 BROWN (8" Tank) (5810, 5812)

61454-1 .................. Injector Assy, #1 WHITE (14" & 16" Tank) (5810, 5812)

61454-2 .................. Injector Assy, #2 BLUE (18" Tank) (5810, 5812)

61454-3 .................. Injector Assy, #3 YELLOW (20" Tank) (5810, 5812)

61454-4 .................. Injector Assy, #4 GREEN (21" Tank) (5810, 5812)

61454-5 .................. Injector Assy, #5 GRAY (24" Tank) (5810, 5812)

Injector Caps

18278-20 Injector Cap Assy, 1610 Regulated, 5800,

20 PSI, Black (5800 only)

18278-30 Injector Cap Assy, 1610 Regulated, 5800,

30 PSI, Gray (5800 only) 61923-20 Cap, Regulated Injector, 20 PSI (5810, 5812) 61923-30 Cap, Regulated Injector, 30 PSI (5810, 5812) 61958 Injector Cap w/o-ring (5810, 5812)

Powerheads

61957 5800/5810/5812 Powerhead.Less Timer, Less Power Supply

INJECTOR ASSY

POWERHEAD

METER ASSY

CAP, REGULATED INJECTOR

TIMER ASSY, XTR2

METER CABLE ASSY

Timers

61931-03 Timer Assy, 5800XTR Touch Scrn w/Logo,

International Lang

62126 Timer Assy, 5800 IOT XTR2 Touch Scrn

62076 Timer Assy, SXT, 62085-01 Timer Assy, LXT 5800, Soft TC DF (5800 only) 62085-02 Timer Assy, LXT 5800, Soft TC UF (5800 only) 62085-03 Timer Assy, LXT 5800, Soft Mtr DF (5800 only) 62085-04 Timer Assy, LXT 5800, Soft Mtr UF (5800 only) 62085-05 Timer Assy, LXT 5800, Fltr Clock (5800 only) 62085-06 Timer Assy, LXT 5800, Fltr Meter (5800 only)

Meter Assemblies

60086-50 Meter Assy, 3/4" Dual Port, Slip Elec,

Plas, Pdl, w Clps (5800 only)

60626 Meter Assy, Turbine, Electronic 3/4"

with Clips and Screws (5800 only)

61919 Meter Assy, 1-1/4", (5810, 5812)

Meter Cables

19121-01 ...............Meter Cable Assy, SE, Paddle (5800 only)

19791-01 ...............Meter Cable Assy, Turbine/SXT

30 • FLECK 5800/5810/5812 XTRI Service Manual

IOT MODULE

Module

62125 ..................... Kit, IOT Module 5800 XTR2

Misc.

40947-02 ...............Plug, Brine Valve, with o-rings (5800 only)

13918-01 ...............BLFC Module Plug Assy, with o-rings (5800 only)

18276-01 ...............Injector Assy, Plug, with o-rings (5800 only)

Page 31

5800 TURBINE METER ASSEMBLY

- P/N 60626

5800 PADDLE METER ASSEMBLY P/N 60086-50

BR60626

Item No. QTY Part No. Description

1.................1 ........ 19797 .................Meter Assy, 3/4" Dual Port, SLP

2.................2 ........ 19569 .................Clip, Flow Meter

3.................2 ........ 13314 .................Screw, Slot Ind Hex, 8-18 x 0.60

4.................1 ........ 60626 .................Meter Assy, Turbine, Electronic

3/4" with Clips and Screws (includes 14613 Flow Straightener)

Not Shown:

......... 14613 .................Flow Straightener

......... 19791-01 ............Meter Cable Assy, Turbine/SXT

Item No. QTY Part No. Description

1.................1 ........ 14716 .................Meter Cap Assy, NT (includes

items 2, 3, and 4)

2.................1 ........ 13874 .................Cap, Meter, Electronic

3.................1 ........ 13847 .................O-ring, -137, Std, Meter

4.................1 ........ 17798 .................Screw, Slot Hex Washer Head

5.................1 ........ 19121-01 ............Meter Cable Assy, SXT, Paddle

(not included in P/N 60086-50)

6.................1 ........ 13821 .................Body, Meter, 5600

7.................1 ........ 13509 .................Impeller, Meter

8.................4 ........ 12473 .................Screw, Hex Wsh, 10-24 x 5/8

9.................4 ........ 13255 .................Clip, Mounting

10 ...............4 ........ 13314 .................Screw, Slot Ind Hex, 8-18 x 0.60

11 ...............4 ........ 13305 .................O-ring, -119

12 ...............1 ........ 14613 .................Flow Straightener

13 ...............1 ........ 60086-50 ............Meter Assy, 3/4" Dual Port, Slip

BR60086 Rev E

FLECK 5800/5810/5812 XTR I Service Manual • 31

Page 32

5800 BYPASS VALVE ASSEMBLY (METAL)

5800 BYPASS VALVE ASSEMBLY (PLASTIC)

60040SS Rev Y 60041SS Rev AA

Item No. QTY Part No. Description

1.................1 ........ 14105 .................Seal, Bypass, 560CD

2.................1 ........ 11972 .................Plug, Bypass

3.................1 ........ 11978 .................Side Cover

4.................1 ........ 13604-01 ............Label

5.................8 ........ 15727 .................Screw, 10-24 x 0.5"

6.................1 ........ 11986 .................Side Cover

7.................1 ........ 11979 .................Lever, Bypass

8.................1 ........ 11989 .................Screw, Hex Head, 1/4-14 x 1.5"

9.................1 ........ 60040SS .............Bypass Valve, 5600, 3/4" NPT

Black Grip Lever, SS

......... 60041SS .............Bypass Valve, 5600, 1" NPT Black

Grip Lever, Stainless Steel

Not Shown:

2 ........ 19228-01 ............Adapter Assy, Coupling,

w/O-rings

BR60049 Rev H

BR18706 Rev J

BR41027 Rev G

Item No. QTY Part No. Description

1.................2 ........ 13305 .................O-ring, -119

2.................2 ........ 13255 .................Clip, Mounting

3.................2 ........ 13314 .................Screw, Slot Ind Hex, 8-18 x 0.60

4.................1 ........ 18706 .................Yoke, 1", NPT, Plastic

......... 18706-02 ............Yoke, 3/4", NPT, Plastic

5.................1 ........ 13708-40 ............Yoke, 1", Sweat

......... 13708-45 ............Yoke, 3/4", Sweat

......... 19275 .................Yoke, Angle 90 Deg, 3/4", NPT

......... 19275-45 ............Yoke, Angle 90 Deg, 3/4", Sweat

......... 19620-01 ............Yoke, Assy, 3/4", R/Angle 90 Deg,

......... 40636 .................Yoke, 1-1/4", NPT

......... 40636-49 ............Yoke, 1-1/4", Sweat

......... 41027-01 ............Yoke, 3/4", NPT, Cast, Machined

......... 41026-01 ............Yoke, 1", NPT, Cast, Machined,

......... 41026-02 ............Yoke, 1", BSP, Cast, Machined, SS

......... 18706-10 ............Yoke, 1", BSP, Plastic

......... 41027-02 ............Yoke, 3/4", BSP, Cast, Machined

......... 18706-12 ............Yoke, 3/4", BSP, Plastic

......... 19620-01 ............Yoke Assy, 3/4", R/Angle, 90 Deg

6.................1 ........ 60049 .................Bypass Plastic

Not Shown:

2 ........ 19228-01 ............Adapter Assy, Coupling,

w/O-rings, Clips & Screws

w/O-rings

32 • FLECK 5800/5810/5812 XTR I Service Manual

Page 33

SAFETY BRINE VALVE

42112 Rev A

Item No. QTY Part No. Description

1.................1 ........ 19645 .................Body, Safety Brine Valve, 2310

2.................1 ........ 19803 .................Safety Brine Valve Assy

3.................1 ........ 19804 .................Screw, Sckt Hd, Set, 10-24 x 0.75

4.................1 ........ 19805 .................Nut, Hex, 10-24, Nylon Black

5.................1 ........ 19652-01 ............Poppet Assy, SBV w/O-ring

6.................1 ........ 19649 .................Flow Dispenser

7.................1 ........ 11183 .................O-ring, -017

8.................1 ........ 19647 .................Elbow, Safety Brine Valve

9.................2 ........ 19625 .................Nut Assy, 3/8" Plastic

10 ...............1 ........ 18312 .................Retainer, Drain

11 ...............1 ........ 60014 .................Safety Brine Valve Assy, 2310

12 ...............2 ........ 10150 .................Grommet, 0.30 Dia

13 ...............1 ........ 60068-10.5 .........Float Assy, 2310, w/10.5" Rod

......... 60068-11.5 .........Float Assy, 2310, w/11.5" Rod

......... 60068-20 ............Float Assy, 2310, w/20" Rod

......... 60068-30 ............Float Assy, 2310, w/30" Rod

14 ...............1 ........ 60002-11.38 .......Air Check, #500, 11.38" Long

......... 60002-27 ............Air Check, #500, 27" Long

......... 60002-32 ............Air Check, #500, 32" Long

......... 60002-34 ............Air Check, #500, 34" Long

......... 60002-36 ............Air Check, #500, 36" Long

......... 60002-48 ............Air Check, #500, 48" Long

......... 60002-26.25 .......Air Check, #500, 26.25" Long

......... 60002-33.25 .......Air Check, #500, 33.25" Long

42112 Rev A

FLECK 5800/5810/5812 XTR I Service Manual • 33

Page 34

WATER CONDITIONER FLOW DIAGRAMS

5800 Upflow

1. Service Position (Treatment)

2. Brine/Slow Rinse Position (Draw)

4. Rapid Rinse Position (Rinse)

5. Brine Tank Refill Position (Refill)

3. Backwash Position

34 • FLECK 5800/5810/5812 XTR I Service Manual

Page 35

WATER CONDITIONER FLOW DIAGRAMS

5800 Downflow

1. Service Position (Treatment)

2. Backwash Position

4. Rapid Rinse Position (Rinse)

5. Brine Tank Refill Position (Refill)

3. Brine/Slow Rinse Position (Draw)

FLECK 5800/5810/5812 XTR I Service Manual • 35

Page 36

WATER CONDITIONER FLOW DIAGRAMS

5810 Upflow

36 • FLECK 5800/5810/5812 XTRI Service Manual

Page 37

WATER CONDITIONER FLOW DIAGRAMS

5810 Downflow

FLECK 5800/5810/5812 XTRI Service Manual • 37

Page 38

WATER CONDITIONER FLOW DIAGRAMS

1. SERVICE POSITION

3. BACKWASH POSITION

INLET

BRINE LINE

2. BRINE/SLOW RINSE POSITION

RESIN TANK

INLET

BRINE LINE

5. BRINE TANK REFILL POSITION

BRINE TANK

5812 Upflow

38 • FLECK 5800/5810/5812 XTRI Service Manual

Page 39

WATER CONDITIONER FLOW DIAGRAMS

BRINE CAM

AIR CHECK

BRINE VALVE

INLET

DRAIN

RESIN TANK

BRINE TANK

BRINE LINE

2. BACKWASH POSITION

BRINE TANK

AIR CHECK

RESIN TANK

DRAIN

INLET

BRINE VALVE

BRINE LINE

BRINE CAM

3. BRINE/SLOW RINSE POSITION

RESIN TANK

BRINE TANK

AIR CHECK

DRAIN

INLET

BRINE VALVE

BRINE LINE

BRINE CAM

5. BRINE TANK REFILL POSITION

5812 Downflow

FLECK 5800/5810/5812 XTRI Service Manual • 39

Page 40

5800 DIMENSIONAL DRAWINGS

Measurements

inches

9.15

232.3

70.2

2.77

38.7

1.53

182.9

7.20

.85

21.5

91.4

3.60

26.7 DISTRIBUTOR TUBE OD

1.05

53.8

2.12

12.7 .50

111.3

4.38

2.90

73.7

7.6 .30

40 • FLECK 5800/5810/5812 XTR I Service Manual

BR61500-5800LNE Rev A

Page 41

5810 DIMENSIONAL DRAWINGS

287.4

11.32

146

5.75

47.8

1.88

29.6

1.17

71.50

2.815

140.1

5.52

91.4

3.60

120.3

4.74

122.4

4.82

5.1 .20

182.9

7.20

61500-5810LNE REV A

FLECK 5800/5810/5812 XTR I Service Manual • 41

Page 42

5812 DIMENSIONAL DRAWINGS

140.08

5.515

29.6

1.17

71.50

2.815

120.3

4.74

5812 2.5" BASE

305

12.0

171.2

6.74

140

5.51

65.4

2.57

91.4

3.60

182.9

7.20

5.1 .20

5812 4" BASE

71.50

2.815

91.4

3.60

182.9

7.20

42 • FLECK 5800/5810/5812 XTR I Service Manual

305

12.0

170.31

140.1

5.52

5.1 .20

6.71

65.5

2.58

36.8

1.45

140.1

5.51

120.3

4.74

61500-5812LNE REV A

Page 43

WIRING DIAGRAM

CHLORINE

GENERATOR

COMM PORT

USB

PRODUCTION

TEST PORT

REMOTE REGEN LOCK REMOTE REGEN START GND

MOTOR / OPTO. ENC.

FLOW METER

-12VDC

-24VDC

AUX2 CMN AUX2 NO AUX2 NC

AUX1 CMN AUX1 NO AUX1 NC

RESET

SWITCH

TOUCHSCREEN

XTR2

NOTE: The reset switch discharges the super capacitor when power is removed

from the control. The super capacitor retains the current time of day in the event of a power failure. Pressing the reset switch on the circuit board while power is applied to the control will have no effect on the control or stored settings.

Chlorine Generator can only be used with +12VDC power supply (international version only).

+12VDC power supply with 5800, 5810, 5812 valves only.

44459 Rev B

IOT

12VDC

COMM PORT

-12VDC

44452U Rev C

FLECK 5800/5810/5812 XTRI Service Manual • 43

Page 44

INJECTOR FLOW DATA

44 • FLECK 5800/5810/5812 XTRI Service Manual

TR18755 REV B

Page 45

5800 PERFORMANCE DATA

Model Name: may include LXT, SXT, XTRI or XTRI

"Rated Service Flow - gpm with an upper collector"

Pressure Drop at Rated Service Flow

"Rated Capacity (grains @ lbs. of salt)"

Rated Eciency (grains/lb. Salt @ lbs. of salt)

Maximum Flow Rate During Regeneration (gpm)

Resin Volume - ft Resin Type - 8% strong acid cation

Tank size

Backwash 8 8 8 8 8 8

Brine Draw & Slow Rinse

@ lb of Salt

Rapid Rinse 6 6 6 6 5 5

5800 - 0.75 ft

5800 - 1.0 ft

Test Model

5800 - 1.25 ft35800 - 1.5 ft

5800 - 1.75 ft

5800 - 2.0 ft

9 11 11 10.5 12.5 12

15 15 15 15 15 15

12,809 @ 2.81

21,051 @ 6.75

24,210 @ 11.25

17,930 @ 3.75

29,467 @ 9.0

33,889 @ 15.0

22,412 @ 4.7 36,833 @ 11.25 42,361 @ 18.75

26,895 @ 5.6 44,200 @ 13.5 50,833 @ 22.5

31,377 @ 6.6

51,567 @ 15.75

59,305 @ 26.25

35,860 @ 7.5 58,934 @ 18.0 67,778 @ 30.0

4,550 @ 2.81 4,780 @ 3.75 4,780 @ 4.7 4,780 @ 5.6 4,780 @ 6.6 4,780 @ 7.5

1.7 2 2.4 2.4 3.5 3.5

0.75 1 1.25 1.5 1.75 2

8" x 44" 9" x 48" 10" x 47" 10" x 54" 12" x 48" 12" x 52"

50 @ 3.0 62 @ 6.75

78 @ 11.25

52 @ 3.75

70 @ 9.0

90 @ 15.0

43 @ 4.7 54 @ 11.25 65 @ 18.75

54 @ 5.6 70 @ 13.5 87 @ 22.5

61 @ 6.6

80 @ 15.75

100 @ 26.25

70 @ 7.5 91 @ 18.0

115 @ 30.0

Valve Cycle Time

Settings (minutes)

Fill @ lb of Salt

18 @ 6.75

30 @ 11.25

8 @ 3.0

10 @ 3.75

24 @ 9.0

40 @ 15.0

7 @ 4.7

15 @ 11.25

25 @ 18.75

8 @ 5.6

18 @ 13.5

30 @ 22.5

9 @ 6.6

21 @ 15.75

35 @ 26.25

10 @ 7.5

24 @ 18.0

40 @ 30.0

Operating Pressure:20 -125 psi or 1.4 – 8.8 kg/Centimeter2, Operating Temperature: 34 - 110° F or 1.1 – 43.3° C Acceptable Salt Type: Sodium Chloride

All Systems above tested at 35psi +/- 5 psi, pH of 7.5 +/- 0.5, Capacity Testing Flow Rate = 50% of the rated service ow rate for the various size systems

These water softener systems have been tested by WQA and conform to NSF/ANSI 44 for specic performance claims as veried

and substantiated by test data. The rated salt eciencies above were also determined in accordance with NSF/ANSI 44 and are only valid at the salt dosage referenced above. An eciency rated water softener is a demand initiated regeneration (DIR) softener which also complies with specic performance specications intended to minimize the amount of regenerant brine and water used in its operation. Eciency rated water softeners shall have a rated salt eciency of not less that 3350 grains

of total hardness exchanged per pound of salt (based on NaCl equivalency) (477 grams of total hardness exchanged per kilogram

of salt), and shall not deliver more salt than its listed rating. The rated eciency of the water softener, the salt dosage at that

eciency, the capacity at that salt dosage and that of the eciency is only valid at the stated salt dosage. Eciency is measured

by a laboratory test described in NSF/ANSI 44. The test represents the maximum possible eciency the system can achieve.

Operational eciency is the actual eciency achieved after the system has been installed. It is typically less than the eciency

due to individual application factors including water hardness, water usage, and other contaminants that reduce the water softener’s capacity. These systems are not intended to be used for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Refer to the system Installation and Service Manuals for set-up

and programming instructions.

Contact your local dealer for parts and service. See your owner’s manual for warranty information.

C US

Tested and Certied by the WQA

to NSF/ANSI Standard 44 & 372 for softener performance & lead free

compliance and CSA B483.1

Pentair Residential Filtration, LLC

13845 Bishops Drive Suite 200

Brookeld, Wisconsin 53005

Rev. F 7/16/19

PHONE: (262)-238-4400

FLECK 5800/5810/5812 XTRI Service Manual • 45

Page 46

5810 PERFORMANCE DATA

Model Name: may include SXT, XTRI or XTRI

Maximum Rated Service Flow (gpm) (W/upper collector)

Pressure Drop at Rated Service Flow Rate (gpm)"

Rated Capacity (grains @ lbs. of salt)"

Rated Eciency (grains/lb. Salt @ lbs. of salt)"

Maximum Flow Rate During Regeneration (gpm)

Resin Volume - ft3 Resin Type - 8% strong acid cation"

Tank size

5810 - 1.00 ft

13.1 14.9 13.7 17.2 18.9

15 15 15 15 15

17,834 @ 4.0 27,949 @ 9.0

32,225 @ 15.0

4,460 @ 4.0 4,580 @ 5.0 4,580 @ 6.0 4,580 @ 8.0 4,580 @ 12.0

2.0 2.4 2.4 3.5 5

1 1.25 1.5 2 3

9" x 48" 10" x 47" 10" x 54" 12" x 52" 14" x 65"

5810 - 1.25 ft3

test unit

22,918 @ 5.0

35,915 @ 11.25

41,410 @ 18.75

5810 - 1.50 ft

27,501 @ 6.0

43,098 @ 13.5

49,692 @ 22.5

5810 - 2.0 ft

36,668 @ 8.0

57,464 @ 18.0

66,256 @ 30.0

5810 - 3.00 ft

55,003 @ 12.0

86,196 @ 27.0

99,384 @ 45.0

Backwash 8 8 8 8 8

Brine Draw & Slow Rinse

@ lb of Salt

58 @ 4.0 76 @ 9.0

95 @ 15.0

46 @ 5.0

58 @ 11.25

72 @ 18.75

54 @ 6.0 68 @ 13.5 86 @ 22.5

49 @ 8.0 62 @ 18.0 78 @ 30.0

58 @ 12.0 76 @ 27.0

98 @ 45.0

Rapid Rinse 6 6 6 6 6

Valve Cycle Time

Settings (minutes)

Fill @ lb of Salt

11 @ 4.0

24 @ 9.0

40 @ 15.0

14 @ 5.0

30 @ 11.25

50 @ 18.75

16 @ 6.0 36 @ 13.5 60 @ 22.5

11 @ 8.0

24 @ 18.0

40 @ 30.0

8 @ 12.0

18 @ 27.0

30 @ 45.0

Operating Pressure:20 -125 psi or 1.4 – 8.8 kg/Centimeter2, Operating Temperature: 34 - 110° F or 1.1 – 43.3° C Acceptable Salt Type: Sodium Chloride

All Systems above tested at 35psi +/- 5 psi, pH of 7.5 +/- 0.5, Capacity Testing Flow Rate = 50% of the rated service ow rate for the various size systems

These water softener systems have been tested by WQA and conform to NSF/ANSI 44 for specic performance claims as

veried and substantiated by test data. The rated salt eciencies above were also determined in accordance with NSF/ANSI

44 and are only valid at the salt dosage referenced above. An eciency rated water softener is a demand initiated regeneration

(DIR) softener which also complies with specic performance specications intended to minimize the amount of regenerant brine and water used in its operation. Eciency rated water softeners shall have a rated salt eciency of not less that 3350

grains of total hardness exchanged per pound of salt (based on NaCl equivalency) (477 grams of total hardness exchanged per

kilogram of salt), and shall not deliver more salt than its listed rating. The rated eciency of the water softener, the salt dosage

at that eciency, the capacity at that salt dosage and that of the eciency is only valid at the stated salt dosage. Eciency is

measured by a laboratory test described in NSF/ANSI 44. The test represents the maximum possible eciency the system can

achieve. Operational eciency is the actual eciency achieved after the system has been installed. It is typically less than the

eciency due to individual application factors including water hardness, water usage, and other contaminants that reduce the

water softener’s capacity. These systems are not intended to be used for treating water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system. Refer to the system Installation and Service Manuals

for set-up and programming instructions.

Contact your local dealer for parts and service. See your owner’s manual for warranty information.

Tested and Certied by the WQA to NSF/

C US

ANSI Standard 44 & 372 for softener

performance & lead free compliance

and CSA B483.1

46 • FLECK 5800/5810/5812 XTRI Service Manual

Pentair Residential Filtration, LLC

13845 Bishops Drive Suite 200

Brookeld, Wisconsin 53005

PHONE: (262)-238-4400

Rev. B 7/09/19

Page 47

5812 PERFORMANCE DATA

Model Name: may include SXT, XTRI or XTRI

Maximum Rated Service Flow (gpm) (W/upper collector)

Pressure Drop at Rated Service Flow Rate (gpm)

Rated Capacity (grains @ lbs. of salt)

Rated Eciency (grains/lb. Salt @ lbs. of salt)

Maximum Flow Rate During Regeneration (gpm)

Resin Volume - ft3 ResinType - 8% strong acid cation

Tank size

5812 - 1.25 ft

5812 - 1.50 ft

14.2 14.8 19 21.9 24.3

13 15 15 15 15

21,604 @ 5.0

33,518 @ 11.25

38,243 @ 18.75

28,111 @ 6.0

43,614 @ 13.5

49,761 @ 22.5

4,320 @ 5.0 4,690 @ 6.0 4,690 @ 8.0 4,690 @ 12.0 4,690 @ 16.0

2.4 2.4 3.5 5 7

1.25 1.5 2 3 4

10" x 47" 10" x 54" 12" x 52" 14" x 65" 16" x 65"

5812 - 2.0 ft3

test unit"

37,482 @ 8.0

58,153 @ 18.0

66,349 @ 30.0

5812 - 3.0 ft

56,233 @ 12.0 87,229 @ 27.0 99,523 @ 45.0

5812 - 4.00 ft

74,964 @ 16.0 116,306 @ 36.0 132,698 @ 60.0

Backwash 8 8 8 8 8

Brine Draw & Slow Rinse

@ lb of Salt

46 @ 5.0 58 @ 9.0

72 @ 18.75"

54 @ 6.0

68 @ 13.5

86 @ 22.5"

48 @ 8.0

62 @ 18.0

78 @ 30.0"

58 @ 12.0 76 @ 27.0

98 @ 45.0"

70 @ 16.0

84 @ 36.0

96 @ 60.0"

Rapid Rinse 6 6 6 6 6

Valve Cycle Time

Settings (minutes)

Fill @ lb of Salt

14 @ 5.0

30 @ 11.25

50 @ 18.75"

16 @ 6.0

36 @ 13.5

60 @ 22.5"

11 @ 8.0

24 @ 18.0

40 @ 30.0"

8 @ 12.0

18 @ 27.0

30 @ 45.0"

11 @ 16.0

24 @ 36.0

40 @ 60.0"

Operating Pressure:20 -125 psi or 1.4 – 8.8 kg/Centimeter2, Operating Temperature: 34 - 110° F or 1.1 – 43.3° C Acceptable Salt Type: Sodium Chloride

All Systems above tested at 35psi +/- 5 psi, pH of 7.5 +/- 0.5, Capacity Testing Flow Rate = 50% of the rated service ow rate for the various size systems

These water softener systems have been tested by WQA and conform to NSF/ANSI 44 for specic performance claims as veried and substantiated

by test data. The rated salt eciencies above were also determined in accordance with NSF/ANSI 44 and are only valid at the salt dosage referenced

above. An eciency rated water softener is a demand initiated regeneration (DIR) softener which also complies with specic performance

specications intended to minimize the amount of regenerant brine and water used in its operation. Eciency rated water softeners shall have

a rated salt eciency of not less that 3350 grains of total hardness exchanged per pound of salt (based on NaCl equivalency) (477 grams of total

hardness exchanged per kilogram of salt), and shall not deliver more salt than its listed rating. The rated eciency of the water softener, the salt

dosage at that eciency, the capacity at that salt dosage and that of the eciency is only valid at the stated salt dosage. Eciency is measured by

a laboratory test described in NSF/ANSI 44. The test represents the maximum possible eciency the system can achieve. Operational eciency

is the actual eciency achieved after the system has been installed. It is typically less than the eciency due to individual application factors

including water hardness, water usage, and other contaminants that reduce the water softener’s capacity. These systems are not intended to be

used for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Refer to the

system Installation and Service Manuals for set-up and programming instructions.

Contact your local dealer for parts and service. See your owner’s manual for warranty information.

Pentair Residential Filtration, LLC

13845 Bishops Drive Suite 200

Brookeld, Wisconsin 53005

PHONE: (262)-238-4400

C US

Tested and Certied by

the WQA to NSF/ANSI Standard 44 & 372 for

softener performance

& lead free compliance

and CSA B483.1

Rev. B 7/09/19

FLECK 5800/5810/5812 XTRI Service Manual • 47

Page 48

For Pentair Fleck§ Product Warranties visit:

pentair.com

§For a detailed list of where Pentair trademarks are registered, please visit PENTAIR.COM/brands. Pentair trademarks and logos are owned by Pentair plc or its affiliates. Third party registered and unregistered trademarks and logos are the property of their respective owners.

44514 REV A JL19

Pentair FLECK 5800, FLECK 5810, FLECK 5812 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual